How to unscrew the head of a fishing line at a trimmer for grass. How to replace a fishing line for a trimmer on a trimmer?

Repair of a trimmer coil for the grass with your own hands: how to remove, disassemble, change a fishing line for a trimmer, assemble and install back

In this article, we will describe in detail the procedure for how to remove the coil of the trimmer for the grass. Step.by.step instructions with the attached video will help a beginner and an experienced user to independently remove the element of the system and clean it or replace it with a new. Before you remove the trimmer coil for the grass, it must be drowned out. for gasoline samples or disables power. for electrimaters. We will demonstrate one traditional dismantling scheme, but in different models of trimmers, the method of attaching the coil to the tool may vary. With your own hands, you can not only remove the old sample of the coil, but also change it to a new one, if such a need arose. So, a step.by.step script:

• Disconnect the tool from the network or turn off the engine (for benzos).
• Carefully remove the cap of the coil, holding a spiral spring in place.
• Click on clamps symmetrically located on both sides with one hand, and the second carefully remove the lid.
• We are looking for a hole in the gearbox cup located on the side or from above, and combine it with the same hole in the shaft hub.
• Using a playground key or a metal rod-we spread it into the gearbox hole, excluding the possible enlarge of the shaft.
• Remove the mowing bobbin on which the fishing line for the trimmer is wound.
• A slightly drowned screw will be visible in the depths. It can be unscrewed by a cruciferous or slotted screwdriver.
• With one hand we hold the body of the head, and the second, counterclockwise, unscrew the screw.
• Light swaying. remove the mowing head. Even if it acidified a little, we make delicately more efforts and with the same swaying. we remove it. Often movements are produced at the watch arrow, but coils are also found that are unscrewed in the other direction.
• The assembly takes place in the opposite sequence.

Removing the bobbin has to be removed in cases of damage, winding of the fishing line (which is undesirable and indicates an illiterate selection of gear), and also when you need to wind a new cord with a new coil or replace the cutting tackle. Buy a coil for a trimmer for grass will always be inexpensively offered by the Kosikosa store.

The procedure for removing a mowing head of a trimmer for grass.

The design and fastening of the working part of the electric cocia differs significantly in different companies of manufacturers. But taking into account that in our markets there are many copies of acceptable recognizable brands, the order described can suit the owners and other portable garden equipment for the care of the lawn and grass.

Trammering head replacement tool.

For replacement, removing the head of the instrument, a nozzle in the form of a star will be useful to us, usually comes with the kit, or a flat wide screwdriver. Use a hexagon of a knife stars will not work, the nozzle slides, licking the edges of the sprocket on the screw.

Installation of a mowing head on a trimmer for grass Black and Decker.

Installation of a mowing head on a trimmer for grass is done in a flip sequence. When installing the screw in place, it is delayed by average effort.

I wish you a successful summer season and so that the garden technique does not fail. I hope my tips on how to remove the mowing head on the BlackDecker GL716 trimmer saved time and nerves for you.

Trimmer head with two antennae

After extracting the spray from the coil body, we determine the number of streams for winding fishing line (1 or 2). There is no principle distinction between bobbins with one and 2 grooves, but with a negligent refueling in a paired groove there is a place to be confused with the operation. Due to the likelihood of interweaving with a tool adjacent, a situation may appear when, after the wear of the workers’ antennae, it is unrealistic to extract new.

Regardless of the number of streams for refueling, a fishing line is taken for a trimmer from 1 length.5 to 3 meters. The winding needs to be created in a flip rotation of the head to the side, because the winding in the direction of movement will lead to the fact that the fishing line for the trimmer will not be removed from the bobbin. After the fishing line for the trimmer is tucked into the coil of the trimmer for the grass, free ends (15-30 cm) we stretch into special holes. Next, collect the head in the back of the order and check the performance. Do not worry if the ends of the 2nd antenpers are very different in size, since when the trimmer for the grass is launched, the knife installed on protection will cut off excess.

Reviews about trimmer for grass gasoline hopper farmer-052

Advantages: powerful, comfortable in hand, not heavy.

Disadvantages: the quality is terrible. During the year of operation, the piston was changed twice, four times the starter. Constant problems with carburetor. In short, they repaired more than worked.

Comment: I will not advise anyone hoper. Before that, Interskol was (and stayed). worked and works at all without problems. We decided to take something ramps and really regretted it.

Advantages: Power of the biceps belt pissing rod

Comment: The device is just a beast. Power is enough for everything. When the trigger presses you immediately feel how powerful it is. At the first acquaintance with Khopom, they said that everything is crumbling. Will start several times and then from the thirtieth. And so on. As a result, he examined everything well, did not listen to anyone and took a chainsaw from Hopra. After two.year use, definitely a hoper if the technique is suitable for needs. And buying a trimmer for grass generally pleased. There were many devices in their hands from different manufacturers. So I can recommend confidently. P. S. Just remember that you take a gasoline tool, not a kettle. Here is not only the button on.-Off., but also proper maintenance. The correct first launch, running.in, lubrication, cleaning, etc. D. All successful purchases!

Disadvantages: Assembly is bad. Half of the bolts are not swept. Fuel tank separate topic. For a year of use, changed three times. First time under warranty, then I bought separately. All three times the tank burst in the same place. The quality of the plastic tank is disgusting. The tank is suspended by only two bolts and brackets. protection of the tank is a plastic corner. After the first replacement, the tank bought enhanced metal protection, but she also did not help. The fuel tank bursts from the vibration of the braid for grass at the mounting site to the engine body.

Comment: This braid for grass was repaired more than worked. I don’t advise buying this braid.

Advantages:.comfortable (biceps belt).Powerful (grass to waist. In dust)

Flaws:. The resource of motorcycles is only 150 (like Huskvarny 600-). If something opens, I will complement.

-They scared that high grass to the waist would not be reimbursed by a trimmer, because everyone has everything wound up on a gearbox. Nonsense, any grass, any burdocks in dust and dust waves. _.Scared that he eats a lot, all the same 3 liters.With. Nonsense, tank here 2l. And for 3 tsenzil, all that was needed (half of the football field), and the grass was really in Posyas. Husqvarna’s neighbor 2 l.With. Eats the same. Scared that cheap and fall apart, everything will bounce. No, everything is tightly screwed and in general, I constantly beat her for bricks and wound the sticks and benches on it)). Nothing fell off. A crack appeared on the coil after I wrapped some kind of metal cable in the grass as a gearbox. But the crack is not significant, then it never went. Friends have been mowing such a mower for a year. Everything is good for them.

https: // jusof.COM/Katushka-dlja-Trimmera-PA6-30gf-Kak-Razobrat/https: // Poryadok.ru/catalog/katushki_leski_dlya_trimmera/https: // otziv-otziv.ru/Katalog/Trimmery/Hopeer/Trimmer-Benzinovy-Hoper-Fermer-052.HTML

Installation of a new fishing line on the coil of a trimmer for grass

Equipping the coil with a new fishing line is performed in the reverse order. The procedure looks like it is described below, regardless of the model of the lawn mower:

Step one: fixing and styling

Fold the end of the fishing line in half. Place the workpiece above the coil on each side of each half of the winding area. Wrap both halves completely around the winding drum. Stretch the fishing line for the trimmer through the loop.

The procedure for preparing fishing line in the field of both wound sections of the drum. The loops are laid in specially made cutouts, after which the winding of the fishing line is performed in each area

Pull the fishing line for the trimmer enough and put the knot in the groove made on each side of the winding drum.

Step two: winding cutting material according to sections

The next step is to turn the fishing line in a circle of coil, observing caution. It is necessary that each half be filled with “its own” winding, exactly, without intersections. Usually on the hull of the winding drum you can see the arrows indicating the direction of winding. This moment should be borne in mind, filling the reel with a fishing line.

Step Three: The Club of the Head Noner

Stretch the ends of the fishing line through a pair of oval cuts of coil. Replace both goals and a spring (if any in the design) with new elements included in the package. Bend both ends of the fishing line at right angles.

The last technical stroke of the process of replacing the fishing line on the trimmer is to put the cover on the head with subsequent fixation by pressure and slight turnover.

Let each end into the hole, which is at the base of the winding drum. Install the coil in the inner area of ​​the head with an emphasis on the spring. Put the lid, leve on the base and light pressure down with a small rotation counterclockwise, put the cover on the tongues of the latch. This is where the replacement procedure is completed.

Install a trimmer head on the shaft

Insert the bobbin back and close the lid to the click of the latch. Fix the gear shaft and screw the part in the starting position.

When using the fishing line, choose the corresponding trimmer head thicker. Models of trimmer heads differ in the thickness of the landing shaft and holes, so it is very important to choose the correct size of the fishing line for a trimmer for grass. If the trimmer for the grass is powerful, then on it you can use a fishing line for a trimmer a little thicker, because it will not create a load on the engine.

Instructions

In order to change the fishing line for the trimmer, it is necessary to extract the old one (if it was).

The coil is part of the design of the trimmer for the grass, which is located inside the head of the motorcosa, drum or bobbin. Depending on the manufacturers of the head can be different. But this article discusses only Patriot, although their mechanism is used by many other companies.

Now you need to understand how to properly remove the head from a trimmer for grass and how to get a drum out of it.

Instructions on how to promote a hand head on a trimmer is described below.

• First of all, you need to clean the head of dirt and adhering grass if it is contaminated. To do this, you need to raise a motorcycle head up and, holding the casing, remove a special protective cover dressed on the drum.
• The next step needs to remove the reel from the drum. The coil is easily removed even with one hand, because it is not fixed inside the drum.
• The drum itself is fixed in the trimmer with a bolt. This bolt must be unscrewed, after which you can easily pull out the drum. To do this carefully, you should support the drum with a coil, while twist the screw counterclockwise.
• Now you can pull the coil out. As mentioned above, it is not fixed in anything except a hook with a metal shaft, so it does not need to be torn off with force. Neatly, in a circular movement you should pull the coil from the drum.
• Now it remains to extract an old fishing line for a trimmer and follow the following instructions.

Installation of the coil and drum in its former place is performed according to the opposite algorithm.

Before the process of refueling the fishing line, it is worth making sure that the thread suitable for a trimmer was bought. In the case when the thread is not suitable, the fuel or energy consumption increases, as well as the load on the motor motor.

In order to replace the thread itself directly, you need to prepare a piece of thread of the required size. Most often, this requires about 4 m fishing line. A specific figure will depend on the parameters of the thread, for example, its thickness, as well as on the parameters of the coil itself. If it is not possible to accurately determine the length, it can be done as follows: insert and wind the thread to such a state that the coil is completely charged (the level of the fishing line will be compared with protrusions in the sides of the coil). It is necessary to ensure that the fishing line for the trimmer sits in the coil exactly.

Do not forget that the thick thread will be shorter than thin.

The instructions for refueling the fishing line in the coil is described below.

• The prepared thread must be taken and turned in half. It should be ensured that one edge is longer than the other by 0.1-0.15 m.
• Now you need to take the ends in different hands. The one that is smaller must be pulled to more, so that it becomes 2 times shorter. When bending, the indentation should be maintained at 0.15m.
• Find the slot inside the coil partition. Carefully prick the loop that turned out earlier in this slot.
• To continue work, it is necessary to determine the direction of winding the thread in the coil. To do this, just examine the coil. there should be an arrow on it.
• If the gunner could not be found, it is quite possible that there is a written designation. An example is given in the photo below. It is necessary to inspect the head of the coil. It has a direction indicator. However, this is the direction of the coil movement. To get the direction of winding, you need to wind in the opposite direction.
• Now you need to season the reel with a fishing line. It is worth noting that there are special guide grooves inside the coil. When wrapping a thread, you need to follow these grooves, otherwise you can damage a trimmer for grass. At this stage, you need to charge the coil very carefully.
• When the user winds up almost the entire thread, you should take the short end (do not forget about the protrusion of 0.15m) and stretch it into the hole located in the coil wall. Now you need to repeat this action similarly with another end (on the other hand).
• Put the coil itself in the coil head, before that, extinguishing a fishing line for a trimmer through the holes inside the drum.
• Now is the time to return the drum to your place. After that, you need to take with both hands by the ends of the fishing line and pull them to the sides. Then you need to put the lid in place (here you can safely make efforts until a characteristic click is heard).
• Remained to perform “cosmetic work”. You need to see if the thread has come out too long. You can start a trimmer for the grass and check in practice whether everything is comfortable. If the thread came out a little long, you can cut it with scissors.

How the head with a fishing line on a motorcycle works why you need to know the principle of work

Depending on the manufacturer, the heads differ structurally not only externally, but also inside. Most drums have a clamping spring inside (semi.automatic and automatic). The instruction is presented above how to disassemble the head of the trimmer for grass without a spring, t.e. on a manual.type head. The principle of dismantling a semi.automatic head with a spring inside almost identical above described instructions.

The principle of operation of the semi.automatic coil of the trimmer for the grass is as follows:

• Inside the head is a coil, which is planted on slots that prevent its free movement
• The coil is affected by a spring that presses it to the slots located in the design of the lid
• A fishing line for a trimmer is wound for a tip, the length of which depends on the tool itself. Usually this length is from 1 to 4 meters
• During the work, if it is necessary to increase the length of the fishing line, the protruding part of the drum occurs, through which it comes out of the hook with the slots. In this case, the fishing line for the trimmer is wound from the drum, increasing in the length
• Having released the required amount of fishing line, you should release the pressing, and continue to perform work on the injection of the grass

The advantage of the tool with a fishing line is that this consumable does not require sharpening compared to metal disks. In addition, if a stone or tree comes across the way, then the fishing line for a trimmer simply breaks off, without having a negative effect on the gearbox and the engine engine, as is the case with metal cutting discs.

Knowing the design and device of the types of mowing or trimmer heads, it is necessary to proceed to the consideration of the process of refueling the fishing line into the coil of the trimmer for the grass. After all, it is precisely this moment that most owners of the Special Instruction causes difficulties.

Removing and disassembling the coil

The braid trimmer head consists of a casing, a spring (not in every model), bobbins with a cord, cover. Before proceeding to disassemble the coil of the electric unit, be sure to turn off the trimmer for the grass from the network. The disassembly method depends on the mounting of the mowing head. First option:

• To remove the lid covering the inside of the head, click on the latches (latches), which are located on its two sides.
• Remove the lid under which you will see the spool. remove it from the body. Some trimmers have a spring under the bobbin coils, which should also be carefully pulled out.
• Removing the bobbin, you will see the screw in the center of the case. Unscrew it with a screwdriver.
• After extracting the fasteners, take the case body and, shaking it in different directions, remove the gearbox from the shaft.

In the second version, the head of the trimmer for the grass is twisted onto the shaft of the gearbox. To remove it, you need to fix the shaft. To do this, in such devices there is a hole through which a thin screwdriver or metal rod is inserted. Brief Instruction:

• Insert a screwdriver into a special hole, then stall the shaft.
• Get the body of the head and start twist it. This should be done clockwise, t. to. Larva shaft thread.

Winding of fishing line on a reel

Shaving

The device was originally intended only for haircuts and trimming, subsequently began to make trimmers for shaving grass, ordinary cars. a special nozzle is intended for this.

• Writing start up from the bottom up from the kadyk, and remove the hairs below the kadyka with a safe razor.
• When shaving the neck, it is recommended to use a slow speed limit.
• The flat part of the nozzle should fit tightly to the skin.
• If the bristles have grown long, it is required to reduce it as much as possible with a ridge and only then use a shaving trimmer.

The device is a trimmer head

Semi.automatic trimmer heads are considered the most popular in the market. A typical representative of the mechanisms of this type is a universal semi.automatic head, which is equipped with electric trimmers for grass and lawn mowers such well.known brands as Bosch, Huter, Husqvarna, etc. Its device is shown in the figure.

• Corps (pos.6) with a lid (pos.1), equipped with special eyes (poses.5) through which the cutting cord is displayed;
• Shpulya (pos.3), on which a fishing line for a trimmer is wound (pos.7);
• a pressing spring (pos. four).

There are other simpler heads.

Characteristic malfunctions and their independent elimination

Naturally, during operation, the owners of the trimmers are faced with certain malfunctions of mowing heads. over, they are most often associated with certain difficulties in pulling (lengthening) of the cutting cord from the coil. The most common causes of the lack of fishing line is its “bite” between the turns or sticking.

If the string is not served

In this case, the cause of the defect is incorrect winding of the cutting cord. A trimmer fishing line can be wound with insufficient tension, which helps to cross the turns together and confuse the string. When the coil rotates, the cutting cord under the influence of the emerging centrifugal force is delayed, which in turn leads to the clamping of the free end of the fishing line between the turns. To eliminate this malfunction, you need to dismantle the coil, disassemble it and rewind the string so that the turns lie down in even rows, pressing tightly against each other.

If the string sticks together

Squeezing of the turns of the fishing line directly in the mowing head can be caused:

Advice! To avoid sticking the cord inside the mowing head, experts recommend applying a thin layer of silicone lubricant after refueling the string to the coil. In addition, it is better not to use a fishing line for a trimmer of unknown manufacturers.

If, nevertheless, the user could not avoid sticking the fishing line, then to repair the trimmer coil for the grass, you need to remove and replace the existing cord with a better.

If there is too much string consumption

When using semi-automatic mowing heads, the user can detect the accelerated consumption of the cutting cord due to its spontaneous lengthening. As a rule, this happens due to the weakening of the spring installed inside the coil. You can eliminate the malfunction by putting several goals under the spring.

If the bobbin does not spin

The refusal to work the semi.automatic coil of the trimmer for the grass can also be caused by a frequent clash of its head with solid objects (dry branches, soil, stones, etc.). In this situation, there is a slight stretching of the fishing line, and then the rapid retraction of it inside the bobbin. Due to severe friction, the cord is heated, which can lead to sticking its turns to each other. To eliminate the defect, the string will need to be rewound.

If the string is served spontaneously

Spontaneous lengthening of the fishing line, followed by pruning its tips, may be caused by a violation of the order of assembly of the head after replacing the cutting cord. Often, users who do not have sufficient experience forget to install the pressing spring inside the head, which causes premature operation of the mechanism responsible for the supply of fishing line.

Dismantling the spit head

Starting to repair the head of the trimmer head for grass, the owner needs to protect yourself from injuries when randomly starting the engine, for which you must completely de.energize the electric garden tool or drown out the engine motorcycle engine. Most often, the owner of a trimmer for grass is faced with the need to replace the cutting cord. This process is started after the head is dismantled from the shaft. This must be done carefully to avoid damage it.

Important! The gearbox shaft, which is equipped with a trimmer for grass, has a left thread at the end, so the mowing head is taped clockwise when removing.

Dismantle the coil in the following order:

• Having combined the holes available on the axis and washer, the mowing shaft is rigidly fixed by means of a screwdriver or a metal rod;
• unscrew the executive mechanism, rotating its case clockwise.

Having removed the braid head, they begin to disassemble it, for which you need to carefully open the lid, which is most often attached specially provided for by plastic locks. To do this, squeeze the edges of the lid and at the same time drown in the hull of the latch.

Attention! If the trimmer for the grass is equipped with a semi.automatic head with a button at the bottom, then it needs to be opened by observing special caution, when removing the cover, a pressing spring can fly out and get lost.

Charging the string in the spool

To charge the fishing line for the trimmer correctly, it is necessary to act according to the instructions for the operation attached to the trimmer. As a rule, this operation is carried out as follows:

• cut off the right amount of cord and fold it in half;
• The resulting loop is inserted into one of the specially provided grooves (holes) of the spool;
• Pulling the fishing line for the trimmer, they turn the spool counterclockwise several times, while the coats of the cord should be laid in dense layers (one to the other), avoiding overlap;
• Having finished winding, the ends of the fishing line (about 20 cm) are left free, which are fixed in the grooves available on the sides of the spool;
• mount the mechanism in their place, for which it is necessary to assemble it in the reverse order, returning to its original position all the available details (spring, washers, etc.), and install the coil with a string in the body of the head;
• The free ends of the cord are passed through the existing eyes (holes), after which the body is closed with a lid, which is fixed with latches.

On this charge of the spitter head, the cord can be considered complete. The coil is screwed onto the shaft of a trimmer for the grass, having previously stiffly fix it. How to do this described above. You can check the performance of the head by mowing a small area of ​​the lawn.

Advice! In those cases when the owner of a trimmer for grass prefers to replace the failed head of the new one, experts recommend avoiding the acquisition of cheap non.original coils brought from China.

Forest winding algorithm

The type, thickness and length of the mowing fishing line are selected depending on the model of the trimmer for the grass. The diameter of the cord can be from 1.2 to 4 mm. It is easy to guess that the thicker you are refueling the cord, the tougher and thicker it can be cut.

There are 3 ways to find out what kind of fishing diameter you can use on your mower.

• Contact the instructions of the device for information about the thickness of the cord.
• Look at the coil itself. It can be marked with information about the possible diameters of the mowing fishing line.
• Insert a trimmer fishing line into a socket. If it passes into it easily, you can use a cord of this diameter.

The fishing line for a trimmer is wound on a coil located in a mowing head. Therefore, it first needs to be opened (this was discussed above). There are two ways to wind the cord.

The first way

To correctly determine how many meters of fishing line is necessary for a specific coil, it is necessary to wind it on the reel so that the coil does not exceed the diameter of the boards. If the fishing line for a trimmer goes beyond the edges of the coil, you cannot insert it into the lid. As soon as you have decided on the length of the material, you need to load it into a reel, so do the following.

• It is necessary to fold a fishing line for a trimmer in half, so one end is 10-15 cm longer than the other.
• Please note that the coil is divided into 2 parts by the central side, with which charging begins. Find a recess on it and insert a cord into it, bent in half, with a slight effort.
• This is very important to determine in which direction the fishing line for the trimmer is wound to the coil. If you look carefully, you can find an arrow on the drum or an inscription with an arrow indicating in which direction to wind. There are cases when there is no arrow on the coil. In this situation, you can look at the drawn arrow on the mowing head and wind the cord in the opposite direction.
• The winding should be carried out carefully, wrapped with a reel, with maximum thread tension.
• After the cord is finished, you must first fix the short end of the mowing fishing line, inserting it into the groove of the corresponding diameter on the side of the coil.
• The other end, genuine, is installed in the groove on the opposite side of the coil.
• After fixing the spit line, cut its ends, leaving the allowances about 10 cm.
• Next, it is necessary to install an aged coil in a mowing head. To do this, insert and stretch the threads into the heads of the head, insert the coil into the housing, and then, applying the required force, pull the fishing line for a trimmer from the fasteners and tighten it.
• Now you can put on the lid and fix it with latches.

Read how to remove the coil from the lawn mower of an electric house

The second method

Some coils provide the second method of fixing the cord: instead of one folded in half, you can charge 2 pieces of thread for a trimmer is replaced in accordance with the following algorithm.

• Before replacing or loading a new thread in a coil, determine how many meters are required, as described above.
• Bend one end of the cord in the form of a hook.
• Find the hole in the bottom of the coil to fix the fishing line for the trimmer, and insert the end of the thread bent into the loop.
• It is necessary to wind the cord in accordance with the direction of the arrow to the desired level not exceeding the diameter of the coil.
• Do the same for the second coil nest.
• The assembly of the head is no different from the method that was provided for when refueling the coil considered with a double piece of fishing line.

There is a very simple and fast way to replace a fishing line for a trimmer without disassembling a mower that you can see by watching this video.

The ends of the cord protruding from the holes in the case can be cut to the required length when the part is installed in the trimmer. There are two ways to do this:

• The inclusion of a trimmer for grass (during rotation, the ends of the fishing line will be trimmed around a knife fixed for this on a protective cover);
• Cutting the extra ends with scissors so that they do not touch the body.

The second method is used if you need to put on a large diameter cord, and the cutter cannot shorten it.

If the thread is tucked on the mowing head, but the length of the protruding ends of the cord is insufficient, they must be lengthened before starting the machine. This applies to the head with manual adjustment. However, there are cases when a semi-automatic mower is used, when, due to the insufficient length of the protruding ends of the cord, they do not automatically lengthen. In this case, you need to turn off the unit (absolutely necessary to pull the fork out of the outlet on the electric device), manually press the button located at the bottom of the part, and pull out a little fishing fishing line for the trimmer. After this procedure, the cord will be able to again lengthen due to centrifugal force if you set the maximum speed of spindle rotation.

The device is a trimmer head

Semi.automatic trimmer heads are considered the most popular in the market. A typical representative of the mechanisms of this type is a universal semi.automatic head, which is equipped with electric trimmers for grass and lawn mowers such well.known brands as Bosch, Huter, Husqvarna, etc. Its device is shown in the figure.

• Corps (pos.6) with a lid (pos.1), equipped with special eyes (poses.5) through which the cutting cord is displayed;
• Shpulya (pos.3), on which a fishing line for a trimmer is wound (pos.7);
• a pressing spring (pos. four).

There are other simpler heads.

The importance of the correct winding

In order for fishing to be successful, you need to carefully prepare for it. Otherwise, “terrible” can happen. the weather is beautiful, the bite is excellent, and the tackle constantly fails and interfere with the use of favorable fishing conditions.

So that this does not happen, you need to configure all fishing accessories in advance. One of the most important stages of preparation for fishing is the correct winding of the fishing line on the spool of fishing coil. Failure to comply with the basic rules threatens the grief of the fishing with confusing and cliffs of the fishing line, and fishing instead of pleasure will become a test for the nervous system.

The casting range depends on the quality of the performance of such work. Proper winding ensures the bait casting to a distance that is the most corresponding to the technical characteristics of the coil.

In addition, high-quality winding extends the service life of the fishing line, reducing mechanical friction and reducing the risk of “beard” when casting, which often has to be cut out the fishing line for the trimmer. Therefore, before starting work, it is necessary to consider some tips of experienced fishermen on how to lay the fishing line on the spool. This is a fairly simple procedure that even a newcomer can handle.

Preparation for replacement

For clarity, a mowing head was removed from the motorcycles (Spool). To replace the fishing line you do not need to remove it, everything is done in place. It doesn’t take much time.

We disassemble the rogue of the trimmer for the grass-it holds on the clan locks. Remove the lid, pressing on the latches. If you do not have enough effort with your hands, then use the screwdriver.

Spool consists of the following:

The principle of action is as follows. By clicking on the button, the coil presses on the spring and leaves the fixing grooves in the lid of the spray. Holding the coil in this state, you can twist, thereby adjusting the length of the fishing line. When the button is released, the housing spring returns the coil to the original fixed state.

Below on the coil there are several holes for a different diameter of the forest. For different manufacturers of trimmers, they may differ. In some cases (as here) they are signed, in others there is no.

These holes are needed to fix the fishing line when replacing it. After winding on the labina of fishing line, the ends of the latter are inserted into them. This is necessary so that the forest does not unwind at the time the coil is installed in the trimmer body for grass. In other words, it facilitates the replacement of fishing line.

There are models without specifying the diameter of the consumable. Then, in order to find out what maximum forest diameter can be used, it is tried on by the openings of the fishing line out of the trimmer’s corps of the grass (see. Figure below).

The coil has two sections for the fishing line separated by a partition. They may not be. They are needed only to distinguish and facilitate the winding of the consumer.

First determined with the required Lessa length. The latter is wound into one of the sections of the coil so that it does not go beyond it. In this case, 3 mm was wound, the length turned out about 2 meters. T.e. For two sections, you will need a segment of 4 meters. this is for the 1st method. For the second method you need two segments of 2 meters.

Replacing the fishing line with a disk or knife

When ennobleing a personal plot, park zones and other places where various plants are required, it is often necessary to change the cutting tool in the trimmer. This is dictated by the fact that the standard cord installed in a mowing head can only cope with herbs. But when a shrub or young growth of trees appears on the path of an employee, a fishing line for a trimmer cannot cope with such a task, and it requires a change to a more effective cutting tool.

Manufacturers of trimmers provided such situations, and complemented their products with a mass of nozzles in the form of knives with several “petals” or in the form of disks similar to circular saws.

If you replace a fishing line for a trimmer with a knife with several “petals”, then such a tool can be mowed by both high grass and plants with thick and dry stems. And changing the fishing line for the trimmer to the disk, the user of motorcycles has the opportunity to cut shrubs or small trees.

Knives and discs are installed according to the following algorithm.

The first thing you need to remove, stagnating the shaft, a mowing head (twist clockwise) or a nut with anthers if the unit has not yet been used.

For a better understanding of the process of changing the tool, you can watch this video.

Problems with fishing line

Trimmeres users, both gasoline and electric, sometimes have problems with the cord. “Advanced” Kosilov owners can easily cope with the difficulties, realizing why this is happening, and for beginners, this is a problem that does not have a rational explanation. But in fact, everything is solved quite simply. The most common problems that happen to the fishing line are the following.

Cords of cord

If a trimmer fishing line is often torn, this can cause the following reasons:

• Stones, small branches and other hard obstacles come across the grass;
• The user mows the grass back to the fence, and if he is mesh, then this breaks the “antennae” even faster;
• poor quality of the cord (it is recommended to purchase high.quality);
• The output holes are worn out in a mowing head, which is why the fishing line for a trimmer is erased on the sharp edges of the bushings and breaks off (a complete replacement of the part will be required).

Large cord consumption

Basically, the cord quickly ends if you often knock on the ground with a semi.automatic head or press it hard. The coil unlock occurs, and the fishing line for the trimmer, lengthening, is cut off with a knife. Another reason that the cord quickly ends is the improper operation of the device with an automatic head: the user during kosbe often drops engine speed. But as we recall, the automatic head is arranged so that it is with each reduction in the revolution that a new portion of fishing line is supplied, so it is quickly consumed.

The thread does not hold

It happens that the thread is unwound if the spring weakened in the semi.automatic head. The fishing line for the trimmer is constantly extended and cut off with a knife installed on the casing, which increases its consumption. To check this, remove the casing and turn on the unit. If the fishing line for the trimmer “climbed”, then you will need to replace the spring.

a fishing line for a trimmer flies out

The reason that the cord after starting the unit is unwound is also a weakening of the spring inside the head. In addition, there are times when when the unit is turned on, a spitter head is scattered, and the spring installed in it is lost. Inexperienced users do not notice the absence of a spring and collect this node without it. Therefore, the cord does not hold, and under the influence of centrifugal force flies out.

The cord is not served, the coil does not spin

Automatic or semi.automatic head should serve a fishing line for a trimmer without stopping the unit. But if it does not come out, then the reasons may be as follows:

• The fishing line for a trimmer in a coil is incorrectly wound, which is why the latter does not spin;
• The cord is wound unevenly, and the thread can get stuck between the turns (the thread should be wrapped neatly, the turn to the turns, without distortions);
• Too short ends of the threads come out of the holes, as a result of which there is not enough centrifugal force to extract them, and the fishing line is not supplied for the trimmer (it is recommended to always adjust the length of the cord before starting the unit, slightly pulling it up);
• The fishing line for the trimmer is sticking together (it will be considered later).

The thread sticks together

This nuisance occurs most often due to the use of poor-quality cord. When the apparatus is operating, the head of the trimmer for the grass heats up, and a poor.quality fishing line for a trimmer in it melts, gluing among themselves. Also, sintering of the threads occurs when a fishing line with a solid obstacle occurs. In this case, there is a sharp braking of the cord, after which it drags it into the head, where it bothers. Some unit owners recommend lubricating the cord with mineral oil or spray on it with a silicone spray after winding on a spul. Others advise to wrap less threads on the coil. But it is better to immediately buy a quality product, in the manufacture of which the manufacturer took into account the factor of overheating of the head, and the thread will not stick together.