How to wind a fishing line for a trimmer for grass on a hanscoonner. How to correct the fishing line for a trimmer: Features…

How to wind a fishing line for a trimmer for a trimmer for grass: step.by.step guides and video instructions

A beautiful lawn will look truly well-groomed only if you regularly give up grass. For processing complex areas, a trimmer for grass is best suited. Any owner of the unit will sooner or later collide with the solution to the problem, how to wrap a fishing line for a trimmer to a coil, because from incorrect actions you can not only worsen the quality of the mowing, but also disable the equipment. Today in the Homius review, we will talk about all the ways and nuances of the replacement of fishing line and the features of the selection of consumables.

It is convenient to use a trimmer for grass for pumping small or complex areas, for example, near the hedge, between the beds and along the paths. Today, manufacturers produce a wide variety of gasoline, electric and battery models, which can be selected for any requests of the owners.

As a cutting element of a trimmer for grass, a fishing line for a trimmer is used. In the process of work sooner or later, its length will end, and then the owner will arise the question of how to properly replace and fix the thread tucked in the removable coil.

What to consider when choosing a fishing line

Before inserting and fixing the fishing line for a trimmer in a removable coil of a trimmer for grass, it is important to choose the right material.

Rating of the best models of gasoline trimmer for grass. Review of manufacturers and models, as well as useful tips from experts considered in this review, will help in a difficult choice among many models of devices.

By quality

Before you put a fishing line for a trimmer on a trimmer for grass, you need to pay attention to the cross section of the cord:

• Round cross.sections are the most common option. They perfectly give way to grass even in complex areas;
• A line for a trimmer with a spiral section is suitable for thin grass. It is not very durable and is not suitable for old thickets;
• The cord with zabrinki and sharp faces is chosen for mating by the weeds;
• A fishing line for a trimmer with a variety of geometric sections will help to mow the lawn more evenly, but the strength of the consumable material is low.

Important! The most wear.resistant consumables are a two.component fishing line for a trimmer with a round section, enhanced from the inside.

The owner of Motokosi should know that it is categorically impossible to use metal wire, fishing thread and a variety of strings.

Rating of the best electric trimmers for grass. In this review, we will analyze the criteria for choosing an electrochemmer, technical characteristics, as well as the most popular models and brands according to consumer reviews.

In size

Before winding the thread, you should pay attention to its size to the coil of the trimmer for the grass. Most often use a fishing line for a trim with a cross section of 2 mm.

You can choose the right diameter in the following ways:

• View recommendations in the manufacturer’s instructions for trimmer.
• Often manufacturers apply information about the cross.section to the bobbin.
• The cross section of the cord should be suitable for the diameter of the coil opening.

Important! The thicker the thread will be seasoned, the more rigid grass it will be able to mow.

Preliminary preparation

First of all, to wind the fishing line, it is required to remove the coil (bobbin, spool) from the trimmer for the grass. specific actions will depend on the complexity of the configuration and the type of product itself:

• Small electric trimmers for grass with a working location of the engine and coils in the lower part, as a rule, have side keys on both sides of the bobbin. With the simultaneous press on them, the upper part of the coil, along with the internal contents for winding the fishing line, is disconnected, while the lower remains on the trimmer. It is advisable to analyze the bobbing in an even smooth place, so that the spring does not jump out and not be lost;
• Electric and gasoline trimmers for grass with a curved rod without the ability to install a knife, as a rule, have coils with a special lamb: in such structures, you should hold the spool in a fixed position with one hand, and rotate the fixing bobbin on the bar with a barack’s baracks. After disconnecting the nut, the whole bobin is removed.
• Electric and gasoline trimmers for grass with the ability to install a knife on a straight rod (for example, trimmers for STIHL grass) have a hole. For the immobility of the bar, a screwdriver or another suitable object is inserted into this hole and, with slow rotation, such a mutual arrangement is achieved when the screwdriver enters the hole and the bob is fixed. After that, the coil body is scrolled clockwise (with the left thread) and removed from the trimmer for the grass.

For the second and third cases, the coil, depending on the design, are versed in various ways. In the bobbins with a lamb, lamb is twisted, in the reels with latches, latches-fixers are pressed and one part of the coil is freed from the other. If the halves of the spool are connected by thread, then it is enough to turn them with your hands in the opposite directions until they are completely developed.

We carry out the winding of the fishing line

Sentlessly completed disassembly of a spray coil without losing its spare parts allows you to go to the main task-winding into a fishing line coil. Technological features of the design of the spool and the number of working antennae determine the sequence of actions.

Coil with one working osik

The easiest option and a simple sequence of actions:

• The dimensions of the bobbin and the length of the original factory winding determine the length of the fishing line recommended for winding. 2 5 m.
• One end of the fishing line is inserted into the fixing technological hole located inside the spool.
• The fishing line for the trimmer is wound on the drum in reverse rotation of the spray in the trimmer product direction. as a rule, on the inside of the bobin, the arrow indicates which direction the winding is carried out.
• A small section of the fishing line is left free to output it. it is fixed in a specialized border on the inside of the bobbin, designed to keep the winding when assembling a spool in working condition.
• The left end of the fishing line is passed through the hole of the outer part of the bobbin.
• Half of the bobbin are collected and put on the bar of the trimmer device.

Two working antennae

In this type of spools, the number of grooves for winding the fishing line lying on the inside of the coil should be determined:

For both cases, a fishing line for a trimmer 2-3 m long is taken. In a single.captable coils, the fishing line for a trimmer stretches into a through hole, its ends (antennae) are folded together and aligned, after which they are wound in the back of the rotation of the bobbin on the bar the side. inside the arrow is usually indicated the correct direction of the winding. In the presence of fixing grooves, the ends of the fishing line are threaded in them or hold their free arm fingers, spread into the through hole of the outer half of the bobin, the spool is closed and attached to the bar of the trimmer product.

The difference between the winding of the fishing line in the two-to-dancing coils is that initially a line of fishing line 2-5 m long is folded in half (to determine the middle fold), and the bend loop is inserted into a special groove between the grooves. Both strains of the fishing line are wound each in its own groove, fixing the antennae and assembly of the coil is similar to the option considered above with one groove.

The first implementation of this procedure may seem long and quite time.consuming, but over time and experience, this task will be solved much faster and easier.

The video below will clearly show how to refuel a fishing line for a trimmer to the coil of a trimmer for the grass and correct it correctly. this operation is not a complicated one and, with some patience, will necessarily be crowned with success:

We carry out the winding of the fishing line

Sentlessly completed disassembly of a spray coil without losing its spare parts allows you to go to the main task-winding into a fishing line coil. Technological features of the design of the spool and the number of working antennae determine the sequence of actions.

Coil with one working osik

The easiest option and a simple sequence of actions:

• The dimensions of the bobbin and the length of the original factory winding determine the length of the fishing line recommended for winding. 2 5 m.
• One end of the fishing line is inserted into the fixing technological hole located inside the spool.
• The fishing line for the trimmer is wound on the drum in reverse rotation of the spray in the trimmer product direction. as a rule, on the inside of the bobin, the arrow indicates which direction the winding is carried out.
• A small section of the fishing line is left free to output it. it is fixed in a specialized border on the inside of the bobbin, designed to keep the winding when assembling a spool in working condition.
• The left end of the fishing line is passed through the hole of the outer part of the bobbin.
• Half of the bobbin are collected and put on the bar of the trimmer device.

Two working antennae

In this type of spools, the number of grooves for winding the fishing line lying on the inside of the coil should be determined:

For both cases, a fishing line for a trimmer 2-3 m long is taken. In a single.captable coils, the fishing line for a trimmer stretches into a through hole, its ends (antennae) are folded together and aligned, after which they are wound in the back of the rotation of the bobbin on the bar the side. inside the arrow is usually indicated the correct direction of the winding. In the presence of fixing grooves, the ends of the fishing line are threaded in them or hold their free arm fingers, spread into the through hole of the outer half of the bobin, the spool is closed and attached to the bar of the trimmer product.

The difference between the winding of the fishing line in the two-to-dancing coils is that initially a line of fishing line 2-5 m long is folded in half (to determine the middle fold), and the bend loop is inserted into a special groove between the grooves. Both strains of the fishing line are wound each in its own groove, fixing the antennae and assembly of the coil is similar to the option considered above with one groove.

The first implementation of this procedure may seem long and quite time.consuming, but over time and experience, this task will be solved much faster and easier.

The video below will clearly show how to refuel a fishing line for a trimmer to the coil of a trimmer for the grass and correct it correctly. this operation is not a complicated one and, with some patience, will necessarily be crowned with success:

We change the fishing line for the trimmer to the disk

The procedure for changing fishing line to disk in a motorcycle is as follows:

• Remove the protective casing from the bar;
• We block the drive shaft of the trimmer for the grass, stretching the screwdriver through the hole in the gearbox bowl to the hole in the shaft hub;
• We unscrew and remove the coil with a fishing line from the hub of the drive shaft for the grass;
• Install a cutting disk on the shaft, combining the slots on the puck of the hub with the recesses of the mounting opening of the disk;
• Again, the stop shaft of the trimmer for the grass and twist the mounting tag of the mount. It is advisable to squeeze the nut with a tubular key, but do not overdo it;
• Put the protective casing back.

Everything, the lawn mower is ready to work with a cutting disk.

Important! The change of cutting elements should be carried out carefully, observing safety precautions. You must definitely familiarize yourself with the instructions and follow all the rules set there. This one will ensure a guarantee of the productive, reliable and safe operation of the trimmer for grass.

The choice of fishing line

In order for the dressing of the fishing line to the trimmer head to be successful, it is important not to fail to choose the consumer material. The thicker the cord you refuel, the more thick and hard grass it can cut. A universal fishing line for a trimmer is often used, the diameter of which is 2 mm. You can choose the diameter suitable for the mower in the following ways:

• See the information about the thickness of the fishing line in the instructions attached to the trimmer.
• Pay attention to the squash itself. Sometimes information is applied on it about possible fishing line diameters.
• Another option is to try to insert the cord into the output. If it easily passes into it, then the selected fishing diameter is suitable for use.

Trimmer coil for grass

You can choose a cord thread by type of engine. If the fishing line for the trimmer is too thick, then the resistance to rotation will increase. the engine in this case will overheat and will soon fail. Useful recommendations:

• For an electric device with an engine of less than 500 in, a thread of 1.3 mm thick is suitable. If this was not found, then you can use a fishing line for a trimmer by 1.6 mm. If the power is more than 1 kW, then select a cord with a diameter of 2 mm.
• The gasoline trimmer for grass has a shaft mower. For the bent version, the cord for 2 mm is often used. If the shaft is straight, then set the thread 2.4–2.5 or 3 mm. The thickest fishing line for a trimmer is installed on powerful devices. from 1.3 kW.

Pay attention to the type of cross section of the cordry thread. Some popular options:

• The most common fishing lines with a round section. They mow fresh herbs well, but they cope worse with shrubs, drows.
• Twisted (spiral) cord does not differ in high strength, but well suitable for thin young grass.
• The jagged thread with sharp edges is ideal for a large weeds in a neglected area.
• You can mow the lawn in a rectangular, starry or square fishing line for a trimmer for grass, but they are not very durable.
• The most durable is a two.component cord with an internal core and a round section.

Types of fishing line for grass for grass

Keep in mind that it is impossible to use wire, metal strings and cables, as well as an ordinary fishing thread. The device will be dangerous for both the user and for others. So the cable or similar products will gradually begin to shut down, as a result, their ends will be reacted, and small pieces will scatter at high speed.

How the head with a fishing line on a motorcycle works why you need to know the principle of work

Depending on the manufacturer, the heads differ structurally not only externally, but also inside. Most drums have a clamping spring inside (semi.automatic and automatic). The instruction is presented above how to disassemble the head of the trimmer for grass without a spring, t.e. on a manual.type head. The principle of dismantling a semi.automatic head with a spring inside almost identical above described instructions.

The principle of operation of the semi.automatic coil of the trimmer for the grass is as follows:

• Inside the head is a coil, which is planted on slots that prevent its free movement
• The coil is affected by a spring that presses it to the slots located in the design of the lid
• A fishing line for a trimmer is wound for a tip, the length of which depends on the tool itself. Usually this length is from 1 to 4 meters
• During the work, if it is necessary to increase the length of the fishing line, the protruding part of the drum occurs, through which it comes out of the hook with the slots. In this case, the fishing line for the trimmer is wound from the drum, increasing in the length
• Having released the required amount of fishing line, you should release the pressing, and continue to perform work on the injection of the grass

The advantage of the tool with a fishing line is that this consumable does not require sharpening compared to metal disks. In addition, if a stone or tree comes across the way, then the fishing line for a trimmer simply breaks off, without having a negative effect on the gearbox and the engine engine, as is the case with metal cutting discs.

Knowing the design and device of the types of mowing or trimmer heads, it is necessary to proceed to the consideration of the process of refueling the fishing line into the coil of the trimmer for the grass. After all, it is precisely this moment that most owners of the Special Instruction causes difficulties.

Where to begin

First of all, it is necessary to remove the head from the motorcycles and open it. for this, latches are provided on the sides of the case.

A spit.headed head of three main elements consists. the head with a spring, a coil, on which a fishing line for a trimmer is wound, and cover.

Before proceeding with the “dressing” of the fishing line, you need to make sure that it is suitable. To do this is very simple. we insert the end of the fishing line into the hole in the head, and if the fishing line for the trimmer passes into the hole without problems, then this diameter is suitable.

The main stages of work

Now we start installing fishing line. There is a dividing side on the coil, which divides it into two grooves for fishing line.

This side has a groove. We measure the desired length of the fishing line, and then bend it in half (while one end should be 10-15 cm longer).

We catch the resulting loop to the groove. Next, look at the case and look for the Wind Line inscription, next to which there will be an arrow that indicates the direction of winding of the fishing line.

If there is no such inscription with the arrow, then look for the arrow on the head, then wrap the fishing line for the trimmer in the opposite direction.

Where to begin

First of all, it is necessary to remove the head from the motorcycles and open it. for this, latches are provided on the sides of the case.

A spitter head of three main elements consists. the head with a spring, a coil, on which a fishing line for a trimmer is wound, and cover.

Before proceeding with the “dressing” of the fishing line, you need to make sure that it is suitable. To do this is very simple. we insert the end of the fishing line into the hole in the head, and if the fishing line for the trimmer passes into the hole without problems, then this diameter is suitable.

The main stages of work

Now we start installing fishing line. There is a dividing side on the coil, which divides it into two grooves for fishing line.

This side has a groove. We measure the desired length of the fishing line, and then bend it in half (while one end should be 10-15 cm longer).

We catch the resulting loop to the groove. Next, look at the case and look for the Wind Line inscription, next to which there will be an arrow that indicates the direction of winding of the fishing line.

If there is no such inscription with the arrow, then look for the arrow on the head, then wrap the fishing line for the trimmer in the opposite direction.

Instructions with a step.by.step description how to wind the coil of a trimmer for grass and lawn mower

In order not to make a mistake with the choice of a suitable fishing line for your tool, you should first disassemble the head and look at the side wall of the coil. This information is usually presented on a tip, which will not allow us to make a mistake using the appropriate equipment.

If the information on the coil about what diameter the fishing line for the trimmer can be refueled, then this information can be clarified in the instructions. Having decided on the thickness or diameter of the equipment, it remains to figure out how to charge it. There are two ways for this, but not for all they are applicable. Consider both methods in details, and already depending on what models and trimmers you use, you are determined on your own which option is suitable.

It is interesting!The principle of how to wind a fishing line for a trimmer for a tip of motorcycles is appropriate not only for autonomous benzar groups, but also for electric trimmers.

Method 1. how to correct the fishing line for a trimmer or put it on a coil and choose the required length

To implement this method, you will need to pre.prepare a fishing line for a trimmer of the required length (usually up to 4 meters). It all depends on the thickness of the equipment used, as well as the design of the coil. There is a simple way to find out the required amount of fishing line, the refueling of which will be needed to charge the coil. To do this, the equipment should be wound inside the coil until it is equal to lateral protrusions. At the same time, the equipment should not go out for these extreme ledges.

The thicker the equipment used, the less its length will need and vice versa, the thinner, the longer the segment will need.

Instructions on how to properly tie the equipment into a tip of a trimmer for grass or motorcycles is the following look:

To begin with, a segment of the fishing line, which was prepared to install in a coil, must be folded in half. In this case, one edge should be more than the second by 10-15 cm

With how to put the drum in place, no difficulties arise. There is a second way to charge mowing equipment into a motorcycle. How is it different, and how the second method of refueling the fishing line to the coil of motorcycles is carried out, we will find out in detail.

The nozzle of the cutting block

The cutting block is the main component of the Philips styler. He has short and sharp edges, and it is used to quickly and accurately trim the hair in length.

To remove the cutting block from the styler case, check the presence of the disconnection button on the styler case. If it is present, click the cutting block removal button.

If there is no disconnection button on the Stayler, place your finger under the teeth of the cutting block and put it out of the device. For re.installation, insert the lower part of the cutting unit into the styler case, and then push the part with the teeth to the click. Do not make excessive efforts; This can lead to damage to the device.

If you fail to install the cutting block, check the presence of foreign bodies in the styler case and try to clean it with a small brush or cotton wool.

No matter how well it works in a summer cottage or a country house that we have acquired an electric trimmer for grass. Sooner or later, the time will come when we need to remove the head of the trimmer for the grass for replacement or prevention. I will immediately make a reservation to replace the fishing line with a trimmer head completely do not need to remove. As part of this article, I will tell you how to completely remove or replace the mowing head on the example of an electric trimmer for BlackDecker GL716 grass.

Tips and recommendations how to wind a fishing line for a trimmer and what you need to know

There are several useful tips and recommendations that it will be useful to find out not only beginners, but also experienced masters-codes. These tips will help prevent negative consequences in the form of injuries and improper functioning of the mechanism. These recommendations say the following:

• Set the lid to clicks. over, these are 2 or more clicks, which depends on the number of fixers. If one latch does not click, then when starting the tool, the drum can jump out and injure a person
• Do not wrap a fishing line for a trimmer with its strong pulling, as well as in an amount more than you can insert it into place. It is better not to harvest the equipment than it will be more, as this will lead to negative consequences in the form of the impossibility of unwinding it if necessary
• If you own the tool not with two conclusions of the fishing line, but with one (usually low.power units), then the winding process is performed in a similar sequence, as described above, only with the difference in the absence of the average side between the extreme bases of the coil
• After replacing the material, it is necessary to first check the tools of the tool, and then proceed to the mocking of the grass. If you do not make a preliminary check, then the forests can be unwound, and injure a person

It is interesting!Choose the material of the appropriate quality so as not to get injuries when working with benzo.cards, trimmers and motorcycles. In the process of beating grass, small stones and other materials fall under the rotating parts, which can fly over long distances, therefore, despite the fact that the fishing line for a trimmer is not a knife, working with a tool should be carried out in protective special uniforms. The result of the work done is as follows. after the replacement of the new material is enough for an area of ​​up to 600 square meters, but when taking into account the presence of a reinforcing layer on the fishing line. Ordinary nylon materials serve less, which is important to take into account when working. Do not try to mow thick.button grass with fishing line, as there are special metal wheels or knives for this.