How To Wind The Line On A Lawn Mower

How to fill the line in a lawn mower: how to change and load into a reel, how to change and how much to wind in a trimmer Lawn mower. It is an indispensable technique at the summer cottage. Its cutting element wears out quickly, so it is important to be able to thread the line in the reel yourself.

Replacement instructions. How to insert the line

It should be noted that the reels in mowers can be different:

• For functioning with one antenna;
• For functioning with two antennae;
• The fishing line must be threaded through the through hole located inside the element.

And do not confuse this part with an extension cord for a lawn mower on a reel, because despite the similar name, these are two completely different elements.

This article will tell you about how much the ZIL 130 dump truck weighs and what this transport is capable of.

Read here //machinspec.com/lesozagotovitelnaya/benzopila/stanok-dlya-zatochki.html how to assemble a chain sharpener for chainsaws with your own hands quickly and easily.

In the first option, winding the cutting element is very simple:

• There is a locking tab on the inside of the spool element.
• One tendril of the thread is inserted into it.
• It is necessary to thread the nylon thread in the direction opposite to the rotation of the spool element.
• You will need only 2 to 4 meters of fishing line. When the winding process is complete, put the small end of this cutting element outward and fix it in the groove, which is necessary for fixing the line so that it does not unwind during the mower operation.
• If there is no special groove, then the end should be held by hand so that the cutting element does not unwind during further assembly of the element.
• At the last stage, it is necessary to thread the outer end of the thread into a special hole located on the outer part of the element. The spool can then be inserted into the mower.

When the roller is working with both ends of the plastic filament, then the following steps must be taken to thread the line into the mower:

• Inside, on the spool, you will see how many recesses there are for winding (two or one). If there is only one groove, then both ends of the thread will be guided through this groove. If there are two of them, then the antennae are laid out separately.. Each in its own notch.
• It is necessary to unwind from 2 to 4 meters of polyethylene thread and thread its two ends into the hole.
• Wind both threads in the opposite direction to the rotation of the drum.
• When all the line is wound, the ends should be fixed in the grooves or held by hand.
• Both ends are threaded into an eyelet on the outside of the roller housing.
• The drum is then assembled and inserted into the mower.

Tips and steps for replacing the line with

The spool element or roller may have a completely different design from the previous two options. The line can be threaded through the eyelet, which is through and located inside the spool. In this case, you do not need to disassemble the roller drum and manually wind the polyethylene thread.

The polyethylene thread is threaded through the hole and rotated by pressing a special button. This the button is located on the body and is intended for the operation of equipment, so that you can release the line as it wears out.

Line device in the mower

The device of the element on which the nylon thread is wound is very simple. This element is called a coil. It has two “tracks”. The upper and the lower. There is a special partition with a recess between these tracks. A fishing line is wound on these tracks. It must first be pulled through the recess.

Features of replacing the fishing line with

How to fill a line in a lawn mower: how to change and load into a reel, how to change and how much to wind into a trimmer

When spring comes, people often spend their free time at their summer cottage. They try to rid their area of ​​problems such as weeds and grass with the onset of warm days. It is difficult to do this manually, especially if the area is very large, so a lawn mower will help. Thanks to this technique, you can trim the grass and remove weeds. It is a suitable device for mowing unnecessary plants near the fence, at home, between rows in the garden on a flower bed, and so on. Read about how to choose the right mower for your needs here. The cutting element in this device is a fishing line (strong polyethylene thread), which is wound on a special element. A spool. But over time, the line wears out and it becomes necessary to replace it. The article will talk about how to fill the line in a lawn mower.

How to change the line on a lawn mower: detailed instructions

In 1971, American entrepreneur George Bollas invented a lawn mower that used a line as a cutting knife. A lot of time has passed since then, the drive has become more powerful, a modern trimmer can easily damage the bark, so the idea itself has transformed into mowing grass around obstacles without damaging the mower cutter itself. For a neat cut around obstacles, a smaller line head can be used and is easy to change when moving from large areas to delicate mowing. However, the cutting tool itself needs to be replaced periodically. We will tell you how to disassemble the head of a lawn mower (trimmer) and wind new line.

Choosing a line for the trimmer head

There are many types of heads available to suit different types of line. The latter is also available in several diameters: from 1.0 mm to 3.2 mm. Over, its cross section is round (including with a special groove to reduce the noise level), square, twisted and in the shape of a star.

There are no clear preferences, this explains the wide variety of shapes and diameters on the market. The round shape is usually stronger, but has the worst cutting ability and also produces a characteristic sound when rotated. Therefore, sometimes an acoustic groove is made on it, however, the use of this fishing line makes sense only on battery trimmers, in cars with a gasoline engine and a network drive, the sound level of the drive itself practically drowns out the sound from the fishing line. The square has a good cutting ability, and despite the fact that this line is less strong than round, on average it is consumed less. Square fishing line quite easily cuts off the growth of the same willow up to 1 cm in diameter. The star has the maximum number of cutting edges, mows the best and is consumed the fastest.

The next nuance when choosing is rigidity. The fact is that during the production of nylon, a modifier (often maleic anhydride) is added to it, which improves its strength and prevents tearing. However, modifiers are not the cheapest component, they are trying to save on it. Therefore, a seemingly good line, which remained for the winter, unexpectedly behaves in a completely different way in the spring. It breaks, stops coming out of the reel normally. There is a recommendation to soak the fishing line in water before work, but I do not see much point in this, maleic anhydride interacts with water, but if it is not enough in nylon, then there will be nothing to interact with. Therefore, it makes no sense to stock up on fishing line for a long period of time, a breaking or constantly breaking line, which, moreover, does not want to leave the reel itself, can significantly complicate the work.

Removing the coil from the trimmer

On small, bottom motor electric trimmers (when operating near the ground), the reel usually has two buttons on the sides. Click on them and disconnect one half of the coil body from the second, which remains on the trimmer. Together with the first half, the inner part is also taken out, on which the fishing line is directly wound. When disassembling, be careful: there is a spring inside that can fly out and get lost.

On electric and gasoline trimmers with a curved bar (there is still no way to put a knife on such trimmers), you need to wrap the coil body itself with one hand, and with the other hand you need to start rotating the lamb on it counterclockwise. It is he who attaches the coil to the trimmer bar. Having unscrewed the lamb, carefully remove the entire coil, trying not to lose the spring inside.

On electric and gasoline trimmers with a straight bar and a gearbox at its end (on such trimmers, in addition to the fishing line, you can also install a knife), we look for a hole under the coil, insert, for example, a screwdriver into it, quietly rotate the coil until the screwdriver crawls even deeper, and the coil will lock. Now we turn the whole coil clockwise (since the thread is left-handed) and remove it from the trimmer. Then we disassemble the coil. It can be assembled with latches or twisted with a lamb. If the coil is latched, then press on the sides on the base of the latches so that they bend and release one half of the coil body from the other. We just unscrew the lamb. There may also be a third type of connection of two halves of such a coil: with it, you need to grab the lower part with one hand, and the upper part with the other, and start turning them in opposite directions. When disassembling such a coil, you must also make sure that the spring inside is not lost.

Than 200 types of trimmers in one place at the lowest prices. Click and watch

Now, having removed and disassembled the coil, we proceed, in fact, to winding.

How to properly wind the line on the trimmer spool

Many, having worked out the factory line on a recently purchased trimmer, try to wind a new one, but cannot, because they do not know how to properly wind the line on the trimmer spool (bobbin). It seems that there is an instruction, but it still does not work. Let’s try to deal with this issue in this article.

So, in order to wind the line, you first need to remove the coil from the trimmer. This will be more convenient. Removal method will depend on the type of trimmer.

In the model with one groove

The line must be pulled into the hole, and its mustache must be folded together and aligned.

Then winding is performed in the opposite direction to the rotation of the bobbin on the mower. Often there is an arrow inside the spool indicating how to put the line on correctly.

The ends of the string are fixed in special grooves or simply temporarily held by hands and pulled into the hole located on the outside of the bobbin.

After that, the spool is closed and attached to the rod, after which the mower is ready for work.

Lawnmower fishing line: how to choose and reel?

1. How to choose the right line?
2. Device in the mower
3. How to rewind?
4. Safety engineering

With the arrival of spring, summer cottages become the main residence of many of our compatriots. However, with the arrival of warm days, there is such a problem as fast-growing grass. It is inconvenient to constantly mow it with a hand scythe, and not all types of grass lend themselves to this old working tool. It is much more convenient to use modern lawn mowers for these purposes. Particularly popular among them are devices with a fishing line, which is easy to change if necessary.

Version with two grooves

The line is first folded in half to determine where the middle of the fold is.

Further, the loop formed at the bend is threaded into the groove that is formed between the two grooves.

After that, you can wind both rods in a separate groove.

You can fix the mustache and assemble the coil completely in the same way as described above.

Opening a reel for the first time and winding a new line is not always easy. Over time, this procedure becomes almost automatic and will not take much time. Some reels have an automatic system that spins the line by itself. As a result, it remains only to correctly set the end of the line, and you’re done. In such models, the string must be put in the hole that is on the outside of the body. Further, the bobbin is assembled, and when the winding rotates, the fishing line is put on it.