Huter trimmer does not work at high speeds. The device of the carburetor of the lawn mower

The lawn mower stalls

When purchasing a lawn mower, you must be prepared for the fact that, as in all other similar tools, breakdowns may also appear in it that will require repairs.

But do not immediately run to the service center and pay big funds to the craftsmen who convince you of the presence of severe malfunctions in the device.

The lawn mower stalls at high speeds

Perhaps more and more a widespread complaint associated with gasoline trimmers sounds like this: “The lawn mower stalls”.

Naturally, a rather harsh fault may be a prerequisite for this. A two.stroke trimmer engine for grass does not develop turns stalling. lawn mower FS 130 give gas stalls. But in most cases, the situation is even easier than it seems to be the 1st gaze.

In order to cope with such an inconsistent, first, try to deal with its causes without the help of others, because, having found out the reason, it’s even easier to fight with the inconsistency, and from time to time it is even self.destructive.

In fact, circumstances, this is when the lawn mower stalls at high speeds, there are quite a lot of these circumstances.

Why is a Chinese lawn mower not developing momentum?

Trimmer for grass does not gain momentum. very frequent inconsistency and of course does not always have a common solution.In this.

The lawn mower is not gaining momentum, the cause of the malfunction and eliminate it

1st launch of the latest lawn mower.Removed the grid from the silencer, began to work.

Another, this is the presence of malfunctions in the power system.

In this case, the lawn mower will stall at idle. At speed stalls a trimmer for Champion grass. GAPHOLLOSKALL GOODLUCK 4300 stalls video revolutions. The lawn mower stalls when you press the gas. At high speeds, the lawn mower stalls. The problems with the power system may lead to a drainage or incorrect carburetor adjustment.

Vibrations that take place in the process of operation of the lawn mower can lead to a reservoir.

Incorrect adjustment of the lawn mower can be fixed by simply adjusting it in accordance with the requirements specified in the operating instructions.

In addition, sometimes gasoline trimmers for grass can stall due to the fact that the valve located in the gas tank cover just clogged or stick.

To find out, try using a braid by loosening the gas tank cover.

If in this mode the device works properly, clean the valve.

over, the lawn mower can stall due to poor fuel flow into the carburetor

Why then the device starts up, ask you?

The reason for this is that at first the fuel gradually falls into the carburetor and is enough for work with increased power.

However, then it is produced and at large speeds the engine begins to stall.

As for the carburetor, here the problem may also be that its body is too pulled.

The reason that the lawn mower stalls at high gas speeds may also be an air leak.

We are talking about the possible presence of a place through which air can pass during the heating process of the engine.

Among other things, do not forget to check the fuel intake hose. GAPHOLLOSKALL GOODLUCK 4300 stalls video revolutions. Husqvarna trimmer stalls when loading. The problem may be that it is weak or cracked at all.

These are the main reasons why the gas mowl can stall.

Do.it.yourself repair and maintenance of a chainsaw

Benzopila are reduced, which makes them more popular and affordable not only for professionals, but also for simple, so to speak, amateurs. However, a widespread dependence. the lower the price, a less reliable device and more frequent failures, since the chainsaw also matters. But for the chainsaw of any price range, most failures can be avoided with proper operation, maintenance and timely maintenance. But no one is safe from the breakdown of the chainsaw and other technologies. Therefore, these are the main types of malfunctions of the chainsaw, methods for their diagnosis, elimination and repair.

All the main malfunctions of chain saws can be divided into two main categories:. engine malfunctions and its various components: the fuel preparation and supply system. ignition, a piston group with a crankshaft, a system for producing curtain gases;. malfunctions and malfunction of other components: lubrication system, clutch, chain brake, tire and others.

Engine starting problems

It is very important to determine the cause of the failure correctly, because otherwise we simply cannot eliminate it. If there are no extraneous sounds when trying to set up a chainsaw (knocking down, grinding, etc. D.), It often turns out that in fact there are no problems. For example, if you put the chainsaw and pull the fork for a long time, the engine simply pours and starts very much.

To properly start the engine saw engine, install the lever or switch to the “flap” position. Then you need to pump the mixture into the carburetor if there is a fuel pump in stock. Pull out the starting handle until the engine resistance becomes noticeable, and energetically extend the amplitude, taking your hand to the side. After two. Three such movements, the engine must first start, and then decay. If this does not happen, then it is necessary to transfer the lever to the position of half.gas or simply to the working position, and then continue to work the chainsaw in this mode. Many Pologaz chainsaws are recorded automatically when the air damper is pulled. Some models have an ignition with the key, it is important to make sure that it is turned on.

If the engine does not start, the first thing to do. unscrew and check the spark plug. There are times when the plant fills the burner with fuel in the cold season. Then you also need to unscrew the candle, dry the combustion chamber with one plant, clean the spark plug, screw it up and repeat the start. It is advisable to immediately check the presence of a spark. On a twisted candle, we put on a cap with a high.voltage wire, we put it on a cylinder, and we pull the starter. Visually observe a frequent blue spark. OK. We twist the candle in place and launch it. If there is no spark, change the candle and repeat the attempt. Again, no. Check the connection of the high.voltage wire to the spark plug, coil and ignition system.

In general, the condition of the candle can be used to determine the type of malfunction.

• Dry. Most likely, the fuel mixture is not included in the cylinder. This is not a ignition system, so the candle is screwed and checked.
• Wet, strongly sprinkled with fuel. The cause of the excessive fuel mixture is to violate the launch rules, as described above, or if the carburetor is incorrectly set up.
• Covered with black carbon. This may indicate the use of poor.quality oil, an incorrectly configured carburetor or an incorrectly calculated ratio of gasoline and oil. The candle should be washed, cleaned of carbon deposits with a sharp object (awl or needle), rub the electrodes with a fabric and installed in place.

When checking the light of the ignition, it is necessary to pay attention to the gap between the electrodes: Normal is considered from 0.5 to 0.65 mm. Damaged or worn gasket should be replaced.

Correctly adjusted carburetor chainsaw provides its effectiveness at full capacity with the most economical fuel consumption.

The need for tuning a carburetor chainsaw is infrequent, since adjustment is originally performed by the manufacturer to achieve the optimal mode of operation. Adjusting screws are designed for a more accurate adjustment of the carburetor chainsaw, if necessary.

Among the causes of violation of fixing the adjusting screws are the most common:

• Strong vibration or damage to a protective cap. This rarely happens, but still happens.
• Serious engine wear (piston). Of course, in this case it is better to take care of repairing a chainsaw, but at the same time, adjusting the carburetor can improve its functionality for some time.
• Litter in a carburetor because of the low quality of gasoline or due to the formation of scale. In this case, in addition to adjusting the carburetor, it can be avoided.

The reasons

Trammers for grass are reliable and durable (of course, subject to proper care). Most often, malfunctions arise due to contamination of structural elements.

If the engine of your lawn mower does not start, does not gain momentum, does not reach the power you need or suddenly stalls, it may be a reason:

• low.quality fuel (fuel mixture), it can be in long.term storage or in non.compliance with the recipe for the preparation of the mixture;
• The grass was wound on the shaft of the fishing/knife head;
• clogging of the air filter/muffler;
• Balance of the carburetor.

Ways to eliminate problems

The first three reasons are quite simple to eliminate. If the matter is the mixture, it is necessary to pour old fuel from the tank, prepare a new emulsion from high.quality gasoline and engine oil (if your motor requires a mixture) and pour it into a fuel tank. If a trimmer for grass works on clean gasoline, it’s still easier.

In the second case, it is necessary to carefully release the details of the trimmer for grass from the wound grass.

If the filter is clogged, you can try to rinse it. If this procedure has not brought the effect, replace it with a new.

The last reason why the lawn mower does not work properly will require you a little more knowledge and skills.

In order to properly adjust the carburetor of the lawn mower, it is necessary to observe a certain procedure. First of all, carefully clean the air filter. The easiest way to rinse it (it is advisable to carry out the filter with water regularly after 9-10 hours of operation).

After that, in the diagram of your trimmer for grass, which is in the instructions for the operation of the device, find the adjustment screws. Usually there are three of them: the first is responsible for the supply of fuel, the second. for idle, but the third is designed to limit the number of maximum engine speeds.

Next, you should turn on the unit and wait for the engine to warm up.

Slowly twist the first adjusting screw (fuel mixture). Catch the moment when the motor begins to stall, and turn the screw in the opposite direction 45 degrees. If you did not have time and the motor stalled, the screw should be turned 90 degrees. Open the throttle and see how the speed is going. Next, you should slowly unscrew the screw (each turn. the same 45 degrees) until the moment when, with full gas, the motor begins to firmly issue maximum revolutions.

The second screw, as mentioned above, controls the engine speed at idle. Weakening it, you reduce the number of revolutions, tighten. increase. The screw must be adjusted so as to ensure confident operation of the motor at small speeds. Accelerate the engine for better starting a little. At the same time, make sure that before the movement of the knives/coil with the fishing line, the motor makes several dozen revolutions. With poor starting the engine, screw the screw slightly.

After you have adjusted the first two screws, test the operation of the device at the maximum engine speed. If necessary, you can limit it (maximum). this will serve as protecting the motor from “boiling”. To do this, you need to do the third screw. Unscrew the fixation nut until the moment when the control screw can be calmly turned. To increase the maximum speed, the screw must be loosened to reduce. on the contrary, tighten. Fix the screw position with a nut. Test the work of the motor again.

Spend the position of the screws regularly. a high level of vibration characteristic of benzocoses can cause their involuntary shift.

Remember that carburetor adjustment is not the final procedure. During operation, Motokos, most likely, you will have to mess with it more than once, because an unbalanced carburetor is both an increased fuel consumption and a quick failure of the candles, not to mention reducing the power and productivity of the device.

Some tricks of work with a benzotrimer.

Now is summer, and gasoline engines have become a constant attribute on land plots. Great tool, powerful and mobile. You can mow grass with a gasoline trimmer and cut dry weeds. But sometimes the braid for grass does not start, works with interruptions or does not develop full power. Now, of course, is not the time to work! As they say, this is rather the vibration of the starter handle than the kosba.

Problems with the launch do not only have an old braid for grass, but also in the new. what is the answer? Only one thing remains. listen to expert advice and adopt their practical experience.

You bought yourself a new gasoline trimmer for grass and difficulties immediately arose with it. It starts very badly. If you rush a little, and then turn it off, then get it “on a hot” even bigger problem than “for cold”. What to do with it, I won’t know how to start correctly?

Pour the fuel using the silicone button (primer) on the bottom of the carburetor. Press as much (or more) as indicated in the instructions, usually about 8-10.

At high speeds, fix the throttle lever using the throttle button.

Pull the starter lever 2-3 times. The engine must “grab”.

If the engine “grasps” and stalls, transfer the throttle to 1/2 and try to run again. If the engine still starts, lower the throttle and transfer the air damper to the position “Open”. Start operation.

When performing manipulations with a fuel pump, do not be afraid of overflow. If this happened, and you, as they say, “flooded the cork”, do not need to unscrew it, just transfer the air damper to the “open” position and, holding the full gas, simultaneously scroll through the engine with a starter 2-4 times. Then you can start the engine and start work.

Ways to eliminate breakdowns

The following works are possible by carburetor:

• cleaning and adjustment of the fuel supply valve;
• similar work with a valve producing spent gases and pairs (after fuel burning);
• replacement of the spring weaker on the entrance valve;
• restoration of the tension of the carburetor cable;
• replacement of the fuel leaks hose, verification and strengthening of a weakened connection;
• changing the rotor damper disk;.
• Change of faulty wire or ignition coil.

The list of work on the work may also include the cleaning of the nozzles (in a 4-stroke engine), replacement of the valve washer, gaskets in tanks and so on.

Operating advice

It is worth paying attention to several recommendations for working with a benzoca or a trimmer that extend the service life of the device to several times.

• As soon as you notice that the lawn mower or trimmer vibrates for the grass. immediately stop working and check the serviceability, performance of specific parts.
• Valves adjustment and checking the work of pistons and cylinders, cleaning and changing the nozzles perform, starting from the requirements set forth in the user guide and the recommendations of the masters of service centers.
• When air bubbles enter the system due to impaired fuel hose-give in to gas. With the combustion of gasoline with higher speeds of the gas bubbles motor will be less. But this is a temporary measure. As soon as possible, disassemble the unit and eliminate the cause of the suction of excess air.
• Do not work as a unit in cold weather, not heating the engine. under load it can often stall. The effect here is the same as in the case when the driver in.40 started the car and immediately drove off, without waiting for the engine heating.
• Do not leave the unit on the roadway. During the accident, the hit will immediately break, and this will make the purchase of a new unit for a forced measure. A car that has crashed into it at best will receive damage to the body and bumper.
• Avoid working with a motorcycle or a trimmer in a downpour. Water getting along with air in the worst case can lead to engine explosion. Similar situations arose with cars.
• Do not use unverified vehicles and lubricants. The mower warms up the engine more than it would do the car itself. when overheating, it will automatically lose its lubricants. It will turn into a burned out reagent. sticky, too viscous and viscous, like fuel oil. He will immediately stall (and drown out) the motor.
• If the oil is old, previously merged from the tank of the machine or other (or the same) lawn mower (on a 4-stroke engine)-defend it, filter to clean from dirt and metal. But at the first opportunity, purchase fresh motor oil.
• If the engine is two.stroke. observe the ratio of gasoline and oil. For compositions with mineral oils, this is approximately 34: 1, for semi.synthetics. 42: 1, for purely synthetic. 50: 1. Do not violate these proportions: “rewinded” gasoline will not burn out and quickly clog the engine, “under.appropriate”. will accelerate the wear of its mobile parts.
• In terms of viscosity to winter classes, they include marking oils: SAE-0W/5W/10W/15W/20W/25W. To the summer-SAE-20/30/40/50/60. For example, SAE 10W-40 is already all-season oil (when working mowers from spring to autumn inclusive). Be sure to check with the manufacturer exactly what oil is needed.
• Always use high.quality gasoline that has passed the manufacturer all stages of cleaning.
• Recommended octane number of gasoline-AI-92/95/98. The use of the 76th can lead to a non-power of the engine by frequent stalling if you are poured, for example, the 76th or 80th gasoline.
• If you are not sure of the independent solution of problems with a gas station (which does not gain move and often stalls)- call the master or contact the service center for repairing motor and garden equipment. Specialists do not get used to doing this work for you.

Observing all these precautions, you will give your mower for many years of fruitful work, and yourself. the luxury of well.groomed lawns, comfort and convenience when mowing unnecessary vegetation in your site.

About the reasons why the lawn mower stall when you press gas, watch in the next video.

The trimmer for grass stalls. how to eliminate the problem

A gasoline trimmer for grass is a useful tool for cleaning from unnecessary grass of house territories and large area lawns. The design of this technique is quite complicated, therefore, if the device breaks, there may be several reasons. The most likely factors that have caught a breakdown are usually described in the user guide. Knowing why a trimmer for grass stalls, you can try to independently eliminate the defect. The most common malfunctions provoking the motorcycle stops, and the ability to repair them with your own hands is in the material further.

In order to most accurately determine the cause of the trimmer malfunction for grass of any brand (for example, echo) and find out the possibility of eliminating it, you need to install, when performing what action the device stalls. The engine can turn off both at idle and at high speeds, heated under load or immediately after starting and t.D.

If you stalled after gas supply

Owners of gasoline braids often mention that the lawn mower stalls when you press the gas. Usually such a breakdown occurs due to problems in the carburetor. A failure in his work can occur due to long-term storage, use in difficult conditions, significant overload of the motor. The symptom of such a breakdown will be vibrating movements of the device during operation.

On a note! Users familiar with the repair of a car carburetor can try to restore this important node of the trimmer for the grass on their own, using the instructions for operating. Otherwise, the correct decision will be to seek help from the service center representatives.

Sometimes a trimmer for grass stalls when you give gas because the fuel valve is clogged. This interferes with the supply of gasoline. To eliminate the problem, it is enough to loosen the valve. Thus, normal supply of carburetor fuel will be restored.

Another possible reason why the lawn mower stalls when gas is supplied is pollution of the soundtress (check valve). This detail prevents the appearance of a vacuum in a gas tank. If it is clogged, the air does not flow, which means that fuel does not go to the carburetor. To eliminate the problem, it is necessary to clean this element.

If it stalled at high speeds

If the carburetor stalls at high speeds, this means that in idle and small there are enough incoming fuel, and to work on high is not enough. Then it is necessary to check the serviceability of the following nodes of the trimmer for the grass.

• Fuel hose. its integrity could be violated as a result of cracking. In this case, you need to replace the part. Or maybe you just need to tighten the clamps.
• A filter network between a carburetor and a hose for supplying a gasoline mixture-it could clog. In this situation, it is necessary to clean the detail.
• The valve on the gas tank cover. he could stick or clog with garbage. Cleaning is also necessary.
• Carburetor. perhaps as a result of constant vibration, it was resolved. This is usually characteristic of cheap Chinese details. To eliminate the problem, it is necessary to set up according to the instructions. In some cases, it is enough to only weaken the tightening of the carburetor case. If the adjustment is not possible, it is necessary to install a new element.
• Additionally, check the air filter. Perhaps it will need to be washed and cleaned or replaced with a new one, as he could clog with dirt and particles of grass when tilted technology, when the user mowed in hard.to.reach places.

If you stalled during work idle

If the lawn mower stalls, working idle, there may be several factors reasons.

• First you need to check the prepared fuel solution, when it comes to a four-stroke trimmer working on a gasoline-oil mixture. There is a chance that it is made incorrectly. the proportions are not withstanded. Because of this, the gearbox is warming up, and the revolutions on the drum are lowering.
• Another probable cause is blockage of elements such as a throttle, air filter or carburetor. You need to clean the indicated details.
• Another possible factor is to resolve or incorrectly carried out carburetor adjustment. You need to adjust the setting according to the instructions.
• Observe this problem mono and when opening the air damper. In this situation, the lack of fuel for a trimmer for grass occurs through the fault of the air flow.

If the device does not have enough fuel, it works properly at high speeds or when they increase, but stalls at idle. If the root of the problem consists in the carburetor, the lawn mower will be disconnected both with cold startup and hot.

If you stalled after starting

If the technique starts and stalls immediately after starting, this indicates the wrong settings or deducting the device. As a result of this, the fuel enters the engine unevenly, which leads to significant vibration and disconnecting the trimmer for the grass. To fix the breakdown, it is necessary to reconfigure the device according to the user management.

Another probable problem is the blockage of the valve supplying the gasoline mixture. It must be cleaned.

On a note! If the trimmer for the grass starts, but immediately stalls, it may also mean that the fuel is moving to the carburetor with difficulty. Weakening the valve will help to eliminate the problem. this will provide uniform and free circulation of fuel in the device.

Another possible reason is the damaged fuel intake hose. Air can penetrate through cracks and holes into the system. To solve the problem, you need to increase the engine speed in order to get rid of air bubbles that have penetrated the device.

If you stalled when opening the damper

If the technique works properly at idle, but stalls when opening an air damper, this reports about the penetration of air into the system through cracks in the fuel supply hose or damaged oil seals. To fix the breakdown and establish the work of the tool without driving air from the atmosphere, it is necessary to replace damaged parts.

Preventive measures and operating rules

So that the lawn mower does not work and does not stall when starting, it must be correctly stored and operated. Compliance with the following simple recommendations will forget about problems.

• When begging the grass, you need to monitor the state of the cooling system. It is also necessary to regularly clean the channels in the case and starter’s ribs.
• To clean the tool, you should use kerosene, solvent, or other washing tools.
• You can not clean a hot tool. it must cool before washing.
• It is important to observe the recommended working mode. this will avoid overheating of the engine.
• If a braid for grass is not used over the next thirty days, the fuel must be drained, otherwise it will fall into heavy components that can score the channels of the carburetor.
• After the fuel is merged, the trimmer for the grass should work at idle for some time until it turns off. This will allow you to completely get rid of the rest inside the working mixture.

To store the tool in cold weather, you need:

• completely drain the fuel;
• disassemble the lawn mower, wash and clean all available components;

• inspect the condition of the parts, eliminate all defects that can be corrected;
• pour the required amount of oil into the gearbox;
• Clean the air filter;
• perform partial disassembly of the engine, wash all moving parts, blow and lubricate thoroughly;
• To lubricate the piston, unscrew the candle, then raise the piston to the upper dead point by the starter, pour a small amount of oil into the hole for the candle and do the crankshaft several times.

Important! If there is no way to store a trimmer for grass in a warm dry room, you must first wrap the motor with an embarrassed rag.

Only by observing these rules, you can be sure that the lawn mower will work properly and will not stall for a number of seasons.

As you can see, stopping the work of a trimmer for grass can be caused by many reasons. Most of them can be fixed independently using the user instructions. In cases where there is no self.confidence, the equipment is recommended to be attributed to repairs. It is worth remembering that incorrect actions can cause even greater harm to the trimmer. As a result, the repair of Motokos will cost a much larger amount than it would be initially, and in the worst case, it may be necessary to buy a new unit.

What is the problem of a trimmer malfunction for grass

CHAMPION BAS carburetor, how to adjust? This is just a trimmer for floating type grass. a common option designed to mix air and fuel in the proportions provided. The main problems arising during the operation of the motor are approximately similar to the problems that overtake the carburetor in the car:

• the motor can stall immediately after it managed to start. The reason is that gasoline is supplied in insufficient quantities. This is called “poor” fuel;
• Excessively fed gasoline leads to its incomplete combustion, excessive density of the mixture and uneconomous consumption.

Important! It is necessary to regulate the carburetor under different circumstances: a change in the temperature regime, octane fuel or type of oil, after winter or end of the run.in, load or spontaneous turning of the screws from strong vibration of the body. Some owners prefer to configure the module before each use to make sure of its correct work

Setting up a carburetor of a lawn mower with three adjusting screws

Before starting work, you need to place the lawn mower on a flat stable surface. Remove the chain in the opposite direction. There are motorcycles with two and three adjusting screws. Two screws most often equip the tools produced in China. Consider the adjustment of the carburetor Motokos with three screws.

Setting up a carburetor of a lawn mower with three adjusting screws

Before proceeding with the adjustment of the carburetor of the lawn mower, you need to rinse the air filter. Cleaning is carried out with water with a detergent or soap, and if necessary, a new. Often in the poor work of the carburetor, scibberries are guilty. In order to prevent the filter, it is recommended to clean the filter after every 10 hours of operation of the tool. Do not forget to check the condition of the candle, if there is a dozen, you need to clean it. Candles are consumables and have their own resource. To ensure good operation of the engine of the lawn mower, candles periodically need to be changed. Next, we evaluate how well the carburetor is fixed to the cylinder-piston group. After the preparatory manipulations are completed, you need to start the motor. Let the engine work for 5-10 minutes. Then you need to identify how many adjusting screws on your tool.

There are the following adjusting screws on the gasoline trimmer:

Fuel supply adjustment

At first you need to slowly tighten the screw adjustment screw for the fuel mixture. You need to do this until the engine starts to stall or stalls. Following this, if the engine did not stop working, you need to turn the screw for a quarter of turnover, and if it stalled, then by half the turnover. Next, you should have a stalled engine. Then you need to open the throttle and see how the speed is gaining. Turn the screw for a quarter of turnover again. You need to scroll until the engine begins to confidently gain increased speeds during cuffing. This is the right time when the engine works most economically. There are times when adjusting this screw does not give anything. Often the reason is in the factory spring that is located on this screw. This does not happen to all the tools. And if the spring turned out to be defective, then replacing it will not be difficult. A suitable spring can be purchased at any construction store.

Cooper adjustment

Following the adjustment of the fuel supply, we are accepting for the adjustment of the idle. To do this, you need to adjust the corresponding screw so that the engine works slightly accelerated at small speeds. But it is necessary to trace, for the immobility of the reel with fishing line and knives. Before the start of their movement, several revolutions should remain in stock. The movement of the coil and knives can subsequently lead to the rapid wear of the clutch. Having noticed that the engine starts poorly, you need to increase the number of revolutions at idle. With an increase in revolutions, the fuel mixture is saturated with air, which leads to power loss.

The main signs of the proper idle work:

• Revolutions for a trimmer head;
• Uninterrupted operation of the engine even when the position changes (sharp rise or descent of the knife);
• Calm operation of the engine at a cold move;
• Lack of increased speed of hot engine.

Maximum speed adjustment

Further, for the full tuning of the carburetor of the lawn mower, it is necessary to adjust the maximum speed. It will not be superfluous to look into the instrument operating manual and see the maximum speed value. This amount will help to determine the tachometer most accurately. If such a device was not at hand, we set up by ear. Barely determining the maximum speed of revolutions by ear, we begin adjustment. A screw for limiting maximum revolutions will help in this matter. Control the engine operation at maximum speed. If necessary, reduce speed, weaken the fixing nut and unscrew the screw. If the turnover is too large, then you will need to screw the screw. These actions must be done in order to protect the engine from overheating. Scroll the screw until the clear even operation of the engine is established.

After the work done, if everything is done correctly, the stable work of the tool is provided.

Understand this by the following signs:

What to do if a chainsaw stalls on a gas when you press the gas

One of the most common issues regarding the work of this device: why the chainsaw is stalling when pressing gas and what needs to be done to solve this problem? In such a situation, the following actions must be performed:

• check the fuel filter;
• examine the fuel hoses for tightness;
• check the muffler;
• try to add a little speed;
• Check the condition of rubber oil seals on the crankshaft.

Basil starts and stalls. the reason

If the chainsaw is started and stalling at the first attempts to do the work, then the reason may consist of problems with the brake of the chain or in its jamming due to lack of lubrication. In this case, the level of oil is measured. If the lubricant volume is sufficient, then the reason may be in the tube that leads it to the lubricant mechanism.

Another reason may be a carburetor breakdown. If he needs only adjustment, it can be done independently in accordance with the instructions. If the carburetor needs to be cleaned or repair, then you can not do without the help of professionals.

Another possible cause of this malfunction is a low fuel level in the tank. In this case, the motorcycle is stalling when tilted, since the remainder of the fuel mixture is in the part of the tank, the opposite of the place where the suction tube is located.

Off for a load

Often powerful chainsaws will stagger from cargo. Most likely, you have a clogged fuel filter, and it needs to be replaced. If this does not help, you need to check the quality of the fuel mixture and prepare a new.

The brake of the chain does not work

All chainsaws are equipped with the main and inertial (emergency) brake. The latter is turned on only when a reverse blow occurs. The main brake is intended to stop the circuit when operating engine speeds. Why is the chain on the chainsaw and it does not stop? There are two options:

• The brake tape is strongly worn out and does not provide a sufficient stopping effect. It is necessary to replace the brake tape.
• Pollution of the tape. When working in the cover space, garbage can be clogged: chips, sawdust, dirt, etc.D. Garbage blocks the operation of the brake mechanism, so if the brake does not work, it is necessary to clean the brake mechanism.

Glonet on the “single”

Sometimes the saw stops at idle, and a common cause of breakdown. The obstacle of the muffler. It can be easily cleaned independently, it does not require a high specialist.

In addition to cleaning, there is another option, but we are very careful with it so as not to damage the internal parts of the device.

To adjust the carburetor, you need to find two bolts with letters L and H. The latter needs to turn a little, just half a turnover. He is responsible for the revolution of the device and, if necessary, raises the idle move.

The chain does not rotate

Why the chain of the chainsaw does not rotate when the engine works even at full speed?

• Leading star. Either it jammed it or the crown is so worn so that it does not engage in the hook and the chain does not spin on the chainsaw. In any case, it is necessary to disassemble the asterisk to find out the exact reason why the chain does not spin. If the crown is worn, it is necessary to replace the asterisk (or the crown itself, if the asterisk has a prefabricated structure).
• He jammed the brake of the chain. As a result, the asterisk is blocked by the brake mechanism, while the engine works. It is necessary to drown out the engine and unlock the brake. If this happened under load, the brake mechanism will have to be changed, like an asterisk, t.to. Due to the high temperature, many elements can be melted and overheated.

How to run a stihl mitch

The main steps to launch Stihl mowel:

• Before using the gas trimmer for the grass, read the instructions and check the trimmer for STIHL grass for each part. After you can collect it.
• An important step is fuel preparation and refueling. Prepare the mixture in a measured container. Gasoline and oil are poured into it in the indicated ratio. Using a funnel, the mixture is poured into a fuel tank.
• At the first launch, turn on the ignition without opening the air damper. Place the device on a flat and smooth surface for stability. Now you need to sharply pull the cord from 3 to 5 times. The air damper can be open in any case: the engine is launched or not.

The first launch may require up to 15 jerks. After starting the engine, turn on the non.working refrigerator to warm up. After a while, it stops the button.

The note! This is a universal leadership, since you need to do the same to start Stihl.

In the case of launching an electric trimmer for grass, everything is much easier: you need to read the instructions and act accordingly. Instead of fuel. Electricity

The device is powered by the network, so it is important to provide a sufficient amount of energy so that the trimmer for the grass can get power

After each operation, gasoline and electric trimmers for grass require a thorough examination.

Following the instructions, you can quickly eliminate any minor damage yourself. But sometimes you cannot start the device with your own hands. In this case, it is better to seek help from a professional, especially if it concerns the problem with the engine and the development of speed in the trimmer or lawn mower.

Oleo-Mac lawn mowing service

OLEO-MAC gasoline gas mowers, like all gasoline tools, should be transported for regular maintenance. This is a prerequisite for the factory guarantee that allows the support of the lawn mower in operation. In addition, your tool needs proper and good fuel, motor oil, high.quality cutting equipment. Tools for mowing, whether it is gasoline or electric lawners OLEO-MAC, need to care and are responsible for uninterrupted work and neat bevel.

What the lawn mowers work on?

The passport data indicates the type of gasoline recommended by the manufacturer. It is necessary to fill out inside this type of gasoline, there is no need to fill with a higher octane number. Fuel operating time is directly proportional to the increase in the octane number. Therefore, you must follow the recommendations of the manufacturer in order to avoid problems and premature failure of the Oleo-Mac lawn mower.

Basic rules for refueling: 1. Fill the fuel tank when the engine is cold.2. Do not smoke when refueling away from flammable objects, open fire!3. Use an open or well.ventilated zone for refueling.four. Leave the game in the gas tank so that gasoline expands when heated.5. Avoid fuel and shoes.6. Before storing a gas mower, it is necessary to drain the gas and start the engine to work out another carburetor.

When to change oil in a lawn mower

Since the engine of the 4-stroke lawn mowing Oleo-Mac has an oil pan with oil lubrication, there is no need to produce a fuel mixture of gasoline and oil. However, the lack of an oil filter makes it necessary to change the oil every 50 hours (in practice this is enough to do every year, as soon as the oil begins to get dark and lose its turnover).

How to sharpen a lawn mowing knife

Despite the recommendations on the Internet for screws with a file or an electric grinder, it is recommended to contact the service center. Although experienced mowers recommend a new knife for each new season.

How to adjust a carburetor mowing

The carburetor is responsible for the preparation of a combustible mixture of air and gasoline to supply internal combustion to its cylinders. Adjustment and cleaning of the carburetor, as well as oil replacement should be carried out regularly. over, this service task is not easy. Contact the Oleo-Mac authorized service center to configure the carburetor to ensure optimal performance, as is done at the factory or in preparation for the sale. For work, it is necessary to use special equipment (tachometer), so it is not recommended to adjust the carburetor by ear or by eye. The incorrect engine speed will lead to engine operation at higher temperatures, which can lead to overheating and jamming of the engine.

Why is a Chinese lawn mower not developing momentum?

If you have done operations with the filter, but the work of a trimmer for grass working from gasoline remains the same, the benzotrimer does not gain momentum what to do?

Then you should try to extract the filter from the device in order to provide the so.called “relief” of the trimmer for grass. The lawn mower does not develop speed, why the Chinese benzotrimmer STIHL FS. Should help.

The next and rather common problem when working with a gasoline trimmer is that it simply stalls and does not give any signs of life.

In this case, the problem may be as follows:

The last and most common cause of the breakdown of a gasoline trimmer for grass is that the cable that is located in the carburetor department was just sleeping.

Therefore, make sure that it will be well pulled, but not to the limit, otherwise with too much load on the gasoline trimmer for grass, this small cable can crack and then you will definitely have to contact the service center, and then also throw out many money into the wind.

What to do when trimmers for grass do not start up? The gasoline trimmer for the grass is a surprisingly desired tool with which there is an option to dig not only a small clearing in front of the house, but also an additional whole lawn of large sizes. To chagrin, there is nothing endless here, if it is possible to encounter the purpose that trimmers for gasoline grass.

18 best benzotrimmers of benzotrimers which company is better? Among the leaders in the production of professional garden equipment are Husqvarna, Echo, Hitachi, Stihl, whose benzarmers are reliable, high functionality and good technical characteristics. It is also worth noting the attractive and ergonomic design is modern.

What to do if a benzotrimer is not gaining momentum ?

If you once purchased a trimmer for grass, working with gasoline, then you probably had to face the problem of turning on a trimmer for grass, as well as a problem as a benzotrimer does not gain momentum.

That is why this article has been created.

So, what to do if a trimmer for grass, working for you for several years, suddenly just stops gaining momentum, and the motor simply stalls? In this case, you and I should consider a number of problems related to stopping the work of the motor.

The motor may stall under various circumstances. I have the problem of the STIHL FS38 STIHL FS38. Sometimes the reason for the incorrect operation of the trimmer for grass working from gasoline is the clogging of the air filter.

It is the filter that is one of the most important reasons why the operation of a gasoline trimmer for grass may stop.

Various garbage very often gets into it, particles of dust that also clog the filter, so it needs to be cleaned and washed every month, and maybe more often, it all depends on what power the gasoline trimmer has for the grass, as well as then how often do you use this device.