Is it possible to pour mining into a chainsaw
Why does oil flow from a chainsaw?
If you notice that oil is leaking from the chainsaw, then this is a malfunction and there may be several reasons for it:
How to refuel a chainsaw
Let’s take a look at how to refuel your chainsaw. Failure to feed the saw correctly could pose a threat to the life and limb of the operator.
There are rules that must be followed when refueling the saw:
- do not spill oil and fuel mixture;
- the place where the saw will be refueled must be flat;
- the place must be more than 2 m away from the area where the device will be used;
- the site must be located away from fire; no smoking in this place;
- while the fuel tank is filling, you need to fill the oil tank, which is intended for automatic chain lubrication; you can distinguish containers by special icons;
- before pouring, wipe the container necks with a rag;
- during operation, grease and gasoline must not be spilled, so you need to be careful when unscrewing the canister caps; when refueling, it is better to use a funnel;
- care should be taken when tightening the lid with the latch;
- experts advise not to fill the container completely, but to leave some free space.
During the operation of a properly refueled chainsaw, it is necessary to regularly check the tightness of the containers and the operation of the motor. If the chain gets too hot, or gasoline is consumed too quickly (faster than oil), this should alert you. Before starting work, the chainsaw is run in.
With proper operation of the chainsaw, 1 tank of gasoline should be enough for 30 minutes of operating the device at maximum load. When gasoline runs out, there is still grease in the second container, but in a small amount.
What Gasoline To Pour Into Chainsaw Partner
How to properly refuel a chainsaw
- Preparation of fuel consistency
- Chainsaw refueling sequence
- Features of refueling a chainsaw
Incorrect operation of any tool not only significantly shortens its service life, but also makes it potentially traumatic. This is especially true for devices with the highest injury risk at the beginning, to which the chainsaw belongs.
Chainsaw device diagram.
The operation of the tool always begins with its preparation for work. What kind of gasoline should be poured into the chainsaw. Green tint oil is premium. What kind of gasoline do you need so what kind of gasoline do you put in your chainsaw? Husqvarna, Partner.
What kind of gasoline so what kind of gasoline should you put into your chainsaw? Therefore, pour pure gasoline into. In the case of a chainsaw, this is first refueling.
And although refueling a chainsaw itself is not a super-complicated operation, its incorrect or careless execution can become a prerequisite for a severe threat of tool breakage and injury to the person working with it.
Risks of using fuel and oil surrogates
The design features of the internal combustion engine for chainsaws of domestic and imported assortment exclude the use of biofuel and gas condensate gasoline substitutes, which are more affordable at a cost. The performance characteristics of such a fuel are currently far from perfect.
In the total sales of motor oils, counterfeit lubricants, according to various sources, range from 8 to 15%. Only an experienced specialist can distinguish an original product from a fake.
To eliminate possible risks of early breakdown of the saw, it is recommended to purchase consumables at branded outlets and representative offices of dealer companies.
With all the external similarity, it is forbidden to use oils for two-stroke internal combustion engines of mopeds and light motorcycles for preparing a working fuel mixture. The use of non-recommended lubricants may initiate a denial of warranty by the service department.
What gasoline to fill?
The manual for Husqvarna chainsaws says that you can refuel with gasoline with an octane rating of 90. However, we recommend using AI-92 gasoline. Why 92? Esters are used in AI-95 and AI-98 gasoline as anti-knock additives to increase the octane number.
And AI-95 is generally AI-92 with 5% methyltrebutyl ether (antiknock additive).
Increased in gasoline additives (low-quality) to increase the octane number leads to the appearance of rust on the electrodes of the spark plugs, carburetor jets and “poisoning” of the catalyst, which in turn leads to an increase in fuel consumption.
While AI-92 is a mixture of 92% isooctane and 8% n-heptane. The octane number of isooctane is 100 (it does not give detonation), but n-heptane, on the contrary, provokes detonation, its octane number is 0. AI-92 is ideal for refueling your chainsaw.
What gasoline to pour into a chainsaw?
Manufacturers strongly recommend using only high-quality gasoline for chainsaws, with an octane rating of at least 92 and m ethanol no more than 10%. It is not recommended to use opaque gasoline containing impurities. they will quickly clog the fuel system and engine.
IMPORTANT: it is not necessary to prepare the gasoline mixture for the chainsaw immediately before pouring it into the tank. this can be done in advance.
over, many manufacturers produce ready-made containers with several compartments, for example, for gasoline and oil or gasoline, oil and ready-mixed mixture, and also complete such containers with a special measuring syringe. With its help, oil is collected in the chainsaw in the proportion that is required.
How I Got My Chainsaw Started After 3 Years of Not Using It. EricTheCarGuy
But if the mixture is prepared in advance, then the maximum storage period should not exceed 10 days. over time, the octane number of gasoline decreases, and due to the fact that part of the gasoline from the mixture evaporates, the proportion of oil and gasoline for the chainsaw changes.
Important Tips
In order for a Stihl chainsaw to work productively for many years, you must adhere to the following recommendations:
- Gasoline must be fresh, not from a month old canister.
- It is forbidden to use oils for 4-stroke engines. It will not completely burn out, which will lead to the formation of carbon deposits and a quick failure of the cylinder-piston group (CPG).
- In a 2-stroke engine, the oil should burn without residues, therefore it is more expedient to use “synthetics”, which is characterized by the formation of less combustion residues and smoke.
- When diluting the mixture, it is better to add more than the recommended volume of oil, but within reasonable limits. 5 grams of excess per 1 liter of gasoline will not lead to coking. Larger amounts can cause carbon deposits and damage to the CPG. If you pour 5 grams less than indicated, this is fraught with overheating of the piston and cylinder.
- Do not use a prepared mixture of a month ago.
- It is forbidden to use oils for mopeds. they are not intended for a chainsaw, as they are designed for a lower number of revolutions.
- After the season, the mixture must be completely consumed or drained to avoid loss of gasoline properties, as well as wear of seals.
The proportions of oil and gasoline for a chainsaw: what to use, the ratio, how to fill, dilute
The chainsaw is started by an engine running on a mixture of gasoline and oil adapted to the ambient conditions.
It is necessary to observe the proportions of oil and gasoline for the chainsaw, then the device will work stably. To achieve high power, the saw is used at high engine speeds.
Therefore, increased requirements are imposed on the quality of lubricants and fuel.
Octane number
This is where the fun begins. Can I refuel a chainsaw 95 with gasoline? In all operating instructions for chainsaws, manufacturers indicate in bold type: “Do not use gasoline with an octane rating higher than 92 for preparing the fuel mixture.” It is understandable, but apparently not for everyone. Once from time to time, they bring chainsaws with a burnt-out cylinder to service centers!
Let’s figure out which gasoline is worth pouring into a chainsaw and which is not! For all two-stroke saw engines, you need to use 92 gasoline, the tool is designed for it. Filling 95 gasoline, the engine will begin to detonate (pushing the piston in the opposite direction), something like a micro impact, which will occur almost every revolution of the crankshaft. About 98 gasoline, I think everything is clear, the effect will be even stronger, and it will already be mini strikes.
Dirty gasoline
Some owners of chainsaws are sure that if the tool works in conditions of constant dust (there is even an air compensator in the carburetor in case of a clogged air filter), it means that it is capable of swallowing gasoline with pieces of rust, and working with small pieces of metal will go to lubricate the chain, so?
This is another common misconception, never use gasoline from the bottom of a canister (especially a rusty one). The chainsaw has a carburetor, in which there are small channels that can clog up from these small particles, which in turn will lead to damage to the chainsaw and contacting a specialized workshop.
What gasoline to pour into a chainsaw
Everywhere and everywhere they write and discuss issues related to the choice of oil for a chainsaw, someone recommends only the original, and someone “everything is fine” and on a regular Lukoil 2T! They also raise a lot of questions about mixing gasoline with oil. the process of preparing a fuel mixture for a chainsaw has any more or less human resource. But, no one ever raises the importance of the issue of using gasoline in a chainsaw! Why? After all, all technicians and engineers know how the use of high-octane gasoline affects engines designed to operate on low-octane ones! The chainsaw is no exception!
- How much gasoline is stored
- Octane number
- Dirty gasoline
- Summing up
How much gasoline is stored
During long-term storage, gasoline evaporates (regardless of the brand), a sediment falls at the bottom, it loses its properties, in other words, it deteriorates. It is worth knowing that it is not the gasoline itself that ignites, but its vapors. Therefore, if there is a canister of gasoline in the garage since last year, then think, is it worth it? Better leave him to light the BBQ fire.
The use of “stale” gasoline for a chainsaw entails many problems:
- difficult start;
- decrease in maximum power;
- increased wear of the engine parts of the chainsaw.
It is worth remembering that the prepared fuel mixture (gasoline with oil) is stored for no more than a month, after this time it should be disposed of. Using old mixture increases wear on the engine parts of the chainsaw. do not forget about it!
Summing up
In order for the chainsaw to serve for many years, never fill it with old gasoline, and you do not need to use grade 95 and especially 98 gasoline to prepare the fuel mixture, only 92. Also, do not forget about the purity of gasoline. no odens!
I hope that now you are not wondering which gasoline for a chainsaw is suitable and which is not very.
What will happen if you pour working off into a chainsaw
If you do not want your chainsaw to fail at the wrong time, use only high-quality fuels and lubricants. It is forbidden to mix working off with gasoline. The reasons for this are the following factors:
- Other viscosity of the material, therefore, mining is not able to provide effective lubrication of rubbing parts and mechanisms
- The mining contains small particles of metal and shavings, which, getting into the tank, will cause clogging of the fuel filter and channel. If the grease enters the cylinder along with small particles, they will leave their imprint in the form of accelerated wear of the piston rings.
- Emitting a lot of black smoke, which indicates burning oil
It is impossible to pour surrogate materials not only into the gasoline tank, but also into the chain lubrication tank. What happens if you use the development in the tank for chain lubrication can be seen in the video.
Using the instructions, you can independently prepare the correct fuel mixture on which the chainsaw will work. If the fuel mixture is diluted incorrectly, not only will the tool life be reduced, but also its performance will decrease.
Gasoline to chainsaw oil ratio
The proportions of oil and gasoline for refueling two-stroke engines of chainsaws of different brands is 40 to 1 or 50 to 1. This ratio is standard, which is used not only by beginners, but also by experienced sawers. It is this ratio for preparing the fuel mixture that is close to ideal, and provides lubrication of the rubbing parts of the crank mechanism and piston.
How much oil should be poured into gasoline in milliliters? Calculated per ml, the ratio of oil and gasoline 1 to 50 is 20 ml per 1 liter. To prepare the correct mixture, you should fill 1 liter of gasoline in a plastic bottle and dilute it with 20 ml of oil. To correctly measure how much oil to pour, you should take a special measuring container and fill it up to the appropriate mark. If you plan to immediately prepare 2 liters of fuel, then 40 ml of lubricant must be added to this amount of gasoline.
There are other ratios that different manufacturers offer. These values of the ratios differ insignificantly, but if you have subtracted other values in the instrument’s passport, then you need to adhere to them. A value of 1 in 50 or 40 is standardized. Pour 15 ml of oil into 1 liter of fuel in the summer, and in winter add at least 20-25 ml. Knowing the recipe for preparing the mixture, you should also figure out what kind of gasoline to pour into the chainsaw?
Advantages and disadvantages of oil
Any quality machine oil has its pros and cons.
Any quality lube has its pros and cons. Some experts say that any chainsaw oil will work. This is not entirely true, almost any substance can be used for the Hurstavna chainsaw, but the Stihl chainsaw only requires gear oil. When choosing, you need to know the color of the oil well, a two-stroke engine requires a composition that has a reddish, bluish or greenish tint.
To prepare the mixture yourself, you need to use a heat-resistant lubricant, which has a well-known brand name.
Seasonality affects the density of the product:
- Solar radiation intensity.
- Pressure.
What are the features of different oils, you can find out precisely by carefully studying the label on the container. In the absence of instructions or labels on the packaging, you should refuse to use such a substance. At the same time, the performance characteristics of the oils should not change dramatically with a difference in temperature conditions.
You should not use any substitutes, often there are counterfeit products among them (up to 20%). It is quite difficult to distinguish a fake, you need to have special equipment.
It is recommended to store fuel in metal containers. It is best to prepare the fuel mixture in a canister.
There are a large number of oils and each has its own characteristics.
The consistency is done in the ratio:
The performance characteristics of mineral or organic oils intended for the chain itself are not suitable for preparing the fuel mixture. The finished product is poured into the tank (up to half), then mixed (the container must be hermetically closed). Thus, a homogeneous composition is obtained. It is better not to prepare fuel ahead of time, it loses its functional properties rather quickly. At room temperature, flammable liquid deteriorates within two weeks.
How To Fix a ChainSaw if You Put Oil in the Gas Tank. Video
How much oil is required to add to gasoline?
Types of oils used for dilution in gasoline
Chainsaws do not have oil pumps, so combustible mixture alone cannot be used. You should carefully read the instructions that are attached by the manufacturer to each product. There is a lot of information on the Internet, it is not difficult to find it.
If there is no lubrication, the saw will fail after a short time. It is recommended to do preventive maintenance of the unit, fill in properly diluted fuel, in this case the tool will function for many years.
If we take, for example, a Husqvarna chainsaw, then unleaded gasoline with the first addition of grade 92 is suitable. If the composition has a greenish color, then this indicates that the product is a premium class. AI-92 is the optimal product that can be suitable for such a device. On average, professionals advise adding 20 to 50 ml of machine oil per liter. If the power of the unit is one and a half kilowatts, then only 25-27 ml of oil will be required.
How to dilute engine oil and gasoline, in what proportions? This question arises for all users. First you need to stock up on containers:
- Measuring liter bottle
- A watering can, which will allow you to pour the substance into the tank
The process of mixing oil and gasoline is technologically uncomplicated. It is important to observe safety precautions so that static electricity does not accumulate, not a drop of water gets into the fuel.
Types of oils used for dilution in gasoline
What proportions should be done? The engines are mostly two-stroke, so the mixture is usually 1:50. Russian-made chainsaws function with products of the following brands:
For foreign analogues, it is permissible to use two liters of gasoline per 80 grams of oil. Foreign saws are distinguished by economical fuel consumption, the proportions of oil in them vary from 40 to 49 shares.
Shades of oil can vary significantly, this should be taken into account during operation. For example, HP produces reddish engine oil. If the composition has a greenish (sometimes blue) tint, then this is a sure sign that the product is synthetic premium. The quality of such compositions is high, the cost is also rather big.
Chainsaw refueling instructions
Knowing the ratio of the preparation of the petrol-oil mixture, you can start refueling it. Refueling instructions are as follows:
- First you need to prepare the mixture. Having combined the two main components, you should mix them thoroughly.
- Place the tool on a clean and level surface. Before unscrewing the gas tank cap, it is necessary to clean or blow off sawdust, dust and dirt.
- The filler neck must point upwards.
- Install a small watering can in the neck, then pour fuel
- Control the refueling process, as the volume of the tank is small, so it fills up quickly
- Do not fill up to the full maximum, since when the tank cap is closed, the remaining fuel will splash out.
- After the fuel is poured into the tank, immediately add chain lubricant.
- The consumption of fuel and chain lubrication is approximately the same, therefore, both tanks must be filled at the same time.
- After refueling, you can start starting the engine
It is better to start the engine not in the place where the refueling was carried out, but to move to a distance of 2-3 m. The tool is ready for work, and you can start to start it. How the chainsaw engine starts, you can read in this material (link).
Chainsaw device
Each chainsaw has different technical data and can do different work.
Powerful saws are suitable for felling centuries-old trees, small-format chainsaws are more suitable for various tasks in the home garden:
Chainsaw standard blocks:
- Power point.
- Clutch.
- Ignition unit.
- Carburetor.
- Fuel block (oil and fuel tank).
- Filters for cleaning incoming air.
- Starter.
- Chain.
- Tire.
- Chain brake.
- Tension mechanism.
- Chain lubrication element.
Each chainsaw requires high-quality fuels and lubricants, it is they that ensure long-term productive operation of the unit. What gasoline for the chainsaw to fill, in what proportions?
For domestic chainsaws, simple oils are suitable, foreign chainsaws need more complex fuel mixtures that have been thoroughly cleaned.
Making the mixture: important proportions
When using a two-stroke engine, clean fuel is purchased separately and mixed with oil, often in proportions of 1:50. It is structurally impossible to install an oil pump in such an engine, therefore, pouring pure gasoline into the chainsaw is strictly prohibited! The proportions, quantity and some brands are indicated by the manufacturer in the instructions for use.
Important points in the cooking process:
- Domestic chainsaws work with oil M8-V, M-12TPU, M8-V, TP, MGD-14M. In some cases, you can use foreign options;
- Proportions: 2.5 liters of FI-80 gasoline per 100 grams of oil;
- Foreign models are distinguished by minimal fuel consumption. They work on foreign oils, and their proportions become 1:40 or 1:50.
Can used machine oil be put into the chain lubricator of a chainsaw? | Topic author: Nikolay
They said that to lubricate the chainsaw chain, you can fill in any oil, is it possible to fill in the mining from the machine?
Christina Can-it only lubricates the chain.
Leonid S Zaporozhets. no, from Merce. Yes
Natalya You can, only then you will saw with a hand hacksaw.
Alexander is actually extremely undesirable, because, in working off from any machine, there is debris, metal chips and so on. and the oil is supplied to the tire by a pump, which breaks down from this debris, and its replacement can cost up to a third of the price of a saw, so it doesn’t cost.
Zinaida Pro tsedi through gauze or nylon and then.
Daria is easy, the only minus is that the oil is dirty, it is better to fill in any cheap mineral or even a spindle, the issue price is three kopecks
Oksana If there is nowhere to put the working off, add it to the resin and coat the bottom of the house. there will be less dampness in winter. Only it must be poured in BEFORE heating, so that possible moisture has time to evaporate, and not splash then Zoya.
And in the saw it is useless. repairing the saw will then be more expensive. You can use industrial, which is for machine tools. they are cheaper than motor ones, and there are no high temperatures on the chain, it’s not in the engine.
Raisa here, take a curious discussion:
Olesya The experience of ancestors and my personal experience shows that “working off”, if it does not contain impurities of gasoline, solvents, water, is quite suitable for lubricating the saw chain.
It is advisable to filter the “working off” through a cloth before use in order to avoid the ingress of large abrasive Dima into the oil pump.
For optimal operation of the chainsaw, for one bar and one sprocket, two saw chains must be alternately replaced after each sharpening, which must be lubricated with any machine oil to minimize friction of the chain links, sprockets and tires. At the next chain change, the bar must be turned over for even wear. In this case, by the time the two saw chains are completely worn out, the bar and sprocket will also fully use up their life. If you work with only one saw chain, then by the time it is completely worn out, when installing a new saw chain, you will have to change the sprocket and the tire, since they will have a development that does not correspond to the step of the new saw chain, although they could still work.
The presence of soot and fine dust in the “working off” will not in any way affect the relatively short, compared to the engine, service life of the saw chain. Lubricate with clean “Mobile-1”, but the life of the saw chain ends from the fact that its teeth are grinded from periodic sharpening. This is called natural wear and tear. There is nothing eternal. Basically ahead of time, a set of two saw chains, one sprocket, one bar fails in the event of:
– incorrect adjustment of the saw chain;
– inept operation of the chainsaw;
– lack of full lubricant Alla
As for the ecology, when using “working off” as a lubricant for the saw chain, in practice, Lilia did not reveal any environmental disasters either in her backyard or in places of work with a chainsaw in her entire life.
Conclusion: NORMAL “WORKING OUT” FROM THE ENGINE WITHOUT ANALYSIS OF GASOLINE, SOLVENT, WATER, FILTERED THROUGH A RAG, SUITABLE FOR LUBRICATING THE SAW CHAIN.
Saw, Shura, Saw.
Vasily is 9 years old, saw and pour only working off for chain lubrication, everything works like clockwork, saw Partner 350! Don’t listen to anyone, lay boldly!
Oleg working off from the new car is clean, from the old one is dirty. you need to filter.
IN ORDER TO EARN ON YouTube YOU NEED: 1. Create your own channel 2. Connect it to AIR by filling out.
Chainsaw Chain Oil | Page 3 | Forum. FORUMHOUSE
April 25, 2008. Understand this: that special oils for lubricating oil chains are from the evil one or if you have money. Do not defend working off, the soot will not settle in it. l. if as an alternative to use the usual cheap.
You are asking. we answer: chain tension of the chainsaw!
Tags: Can I use a working tool to lubricate a chainsaw chain
Is it possible to use a working tool to lubricate a chainsaw chain
Working out in a chainsaw. Youtube
21 Jan 2016.2 minutes Added by the user Workshop “Sense of tact” Why it is impossible to pour testing into a chainsaw. Which is better for chain lubrication: oil or waste? Duration: 8:16. Sergey.