Is it possible to redo a trimmer for grass in a motorbike. Postings for a motorcycle

Standard malfunctions of motorcycles and their diagnosis

Tomorrow I go to the small homeland, there is work to install the fence. Accordingly, it will be necessary to drill holes under the poles. The pillars have to put a lot. Actually, the ADA Ground Drill-5 motorized car was purchased for these purposes. Having looked at YouTube video, I came to the conclusion that it was necessary to make a rack in the likeness of this one: something changed, but the essence is the same. Made a more convenient handle with gazulale and collected a gearbox from small.modular gears with a ratio of 1: 4.5. The gearbox collected on bushings from cars. Mounting circuit (3 pcs). Stars from tensioner 412. I collected everything in place without drawings.

The most interesting thing is that it was not even possible to try it out :). I assume that below it will be necessary to weld the screen of 15-20 centimeters from land on the lower star.

P.FROM. Drilled 32 holes to a depth of 60-80 cm for pipes 40×60 with a home-made drill for 70 mm. It would be very difficult for me to do this without a rack, since the main effort goes when extracting the drill. The earth is dense virgin, as almost everywhere in the Trans.Urals. Mixtures 92 gasoline with oil ate only about 1.2 liters.

Комментарии и мнения владельцев 21

Bourin in clay 1 m depth, 200 mm screw. Clay is such that the shovel sticks like a tree. It’s hard alone, the sausage is not subtitances. We got sitting together. they got up on both sides, so much easier, you hold, with straining, but in moderation. Drilled holes 150 approximately, in total.

In the process, it will become clear that it is very difficult to twist and keep it very hard. This is not a moped control. In my opinion, it would greatly facilitate the work. this is a two.handed emphasis around the motor, the gas, while it opens simply to the full so as not to bother with it.

They also drilled together, the second man just got on a weight frame, helped to quickly get drunk.

Write as in practice will show. Interesting. It seems to me a problem design. Accuracy is not particularly needed. The eye sees.

We drilled 30 holes with a home.made drill of 70 mm for profile pipes 40×60 to a depth of 60 cm. A couple of times in inexperience he drove deeper and had to conquer a centimeter on full gas :). The drill installation is not for the sake of accuracy, but to apply less effort, which it coped with remarkably. A pair of holes Buril with a drill for 200 mm under the poles, to a depth of 80 cm. It goes to clay remarkably, and then it is problematic. When applying forces from above, the motorcycle becomes poorly, you need to dose the effort. But the main thing is that a different design is needed, the head of the drill, we need more teeth. How on

No other design is needed. Just a complete gas should be opened and the efforts from above are not to be especially attached, to keep it exactly.

This design is the result of several years of use by a person of Motobur almost for professional purposes, including drilling horizontal 7 meter punctures under the road: www.forumhouse.ru/Threads/284530/

Here for seven.meter horizontal punctures, it will just suit. Maybe for vertical drilling with a diameter of 300 mm and a depth of more than 1.5 m is also suitable. But for the fence use of 200 mm and up to 1 m. it will deliver more difficulties than the work will facilitate.

I have long wanted to write a note, how in a simple way to extend the resource of the soil screw Motobur, but still did not reach the keys.

But the other day, the Schnek himself reminded of himself. being put in the barn and put there vertically in the corner to wait for spring, painfully hit me on the forehead when I stepped on him in the dark. And then, rubbing the bump on my forehead, I realized that there is no more opportunity to postpone anymore, otherwise he will pursue me until I write this article.

With the apparent unnecessary motorcycle, it is indispensable. Once in a country house, Motoburg will easily help you build a fence, barn, canopy and other buildings. I even planted seedlings with his help.

Aluminum Grass Trimmer Head New Style 4 Lines Brush Cutter Head Lawn Mower Accessories

But be prepared for the fact that with the first sounds of a motorcycle, like moths into the light, neighbors will begin to fly to your site. After all, they also need fences, sheds and canopies. To refuse neighbors means to make tension in a relationship, this is not an apartment building for you, where you can spit a neighbor running up the stairs in the back. This is not noticeable in the city bustle. Another thing is the village, where every oblique look will be remembered, recorded, deeply analyzed, and so far.reaching conclusions will be made about you that when you know about them you will be disgusting.

Therefore, one must be prepared for the fact that the motorbike will go hands. And if you refuse, then you will go in languages. There is also an intermediate option. to walk with a motorcycle. I chose this particular option.

But in any case, an additional load will fall on the motor. And after a while he will stop drilling the earth.

The fact is that the screw ends with an almost round plate on which the cutter is fixed, and under load it bends at the site of the cutter mount. The cutter rises and stops baking into the soil. You have to press the motorbike with all force to drill. The plate simply rotates, rubs on the ground and is gradually erased, becomes thinner:

But this leads to rapid wear and a screw and a motorcycle. Then you have to remove the plate and straighten it with a sledgehammer, do it again flat.

So that this is not, I came up with a simple solution. to weld a corner with a thickness of 3 mm to this plate:

And after this procedure, no load could bend the plate anymore. A few seasons after a cut, but the plate remained even.

As you can see in the photo, the corner must be welded so that it does not interfere with the tightening screws. The protruding part of it must be cut off with a corner grinder in a circle and also boil. The welding inverter is also obliged to be in every house, this is such a thing that immediately pay off during the construction of the fence, and then I already forgot when I bought a rake, tramps, a wheelbarrow, all this is periodically crushed and then serves for years.

Characteristic

Land.bourgeal equipment has gained very solid popularity. But using it “in its pure form” is very difficult and laborious. The stand for a motorcycle can greatly simplify many work. This design is made from a pair of metal pipes. A carriage is attached to the fixed part, which moves the drilling element.

To move the carriage, the chain is attached to it. And this chain, respectively, is connected to the shaft equipped with an asterisk. When working, twist the hilt up and down. Thus, the gas tank stand allows you to tighten and lower the main stormy part. At the same time, importantly, the reliability and stability of manipulations is ensured, and not just unloading the muscles of the operator.

Must be adjusted to the design. After all, the soil can be different, and a single standard of passage simply cannot be.

Moving on the surface of the Earth will be greatly simplified if you equip the device with wheels.

Description and purpose of motorcycles

When planning to make a home.made motorbike for fishing or land work, it is advisable to first of all study the features of this kind of unit. Homemade motorbike has wide functionality and high efficiency, which made it an indispensable tool. It is used in:

The unit belongs to the category of manual tools and is rightfully considered universal. It is suitable for drilling in the soil of various holes that can be used for planting plants, installing foundation piles, supports and other elements. In addition, the ice.braid from a trimmer for grass with your own hands seems to be an indispensable device used for fishing in the winter season. it is used to drill holes in ice.

The design of the device is extremely simple and consists of two main elements. an engine and a screw with a knife at the end. In the process of work, the engine transfers rotating movements of the drill, so that the screw successfully enters the ground.

possible, trimmer, grass, motorbike, motorcycle

Since the cost of store models is quite large, it is much cheaper to make a home.made gas tank for winter fishing from improvised materials.

Types of a motorcycle

The former are more compact and cheap. One operator is enough to manage them. They are equipped with an engine with a capacity of up to 3 liters. With. The most common engines with a capacity of 1.5.2 l. With. and a working volume of 33-40 cubic meters. cm. Their work is limited by loose sandy soils, a loam and a chernozem. The maximum depth of the hole is 1.5–2 m.

When working with heavy soils, clay, rocky soils, heavy motorized boots are used. They are equipped with engines with a capacity of 3.5 liters. With. And they need two operators to manage. Some heavy motorized boots are mounted not on the frame, but on the cart. Then one manager is enough.

Handyman Tips & Hacks That Work Extremely Well ▶3

Heavy motorburses can be equipped with a hydraulic drive, which is equipped from:

  • a hydraulic pump that provides the pressure of the hydraulic fluid;
  • a hydraulic resort providing a low.speed rotation of a shaft and a drill with a screw;
  • a distribution system that provides a reverse due to switching valves for the supply of hydraulic fluid.

The hydraulic drive is an extremely reliable system, since it does not contain a large number of rubbing mobile parts and provides sufficient power and torque to work on large diameter screws on heavy soils. However, such systems are very expensive for non.thought use without a permanent front of work. Heavy motorized boots with a hydraulic drive cope with drilling to a depth of 5 m.

The presence of reverse and several transmissions is extremely useful properties for motorcycles, as they avoid jamming the drill with a screw and choose the optimal mode of operation.

Electric chainsaw or saw. what to choose for the garden? 4 Errors when growing tomatoes in pots that almost all housewives are the secrets of growing seedlings from the Japanese, who are very reverent to the ground

The principle of operation of the gearbox motor for the drilling rig. prof

Creating source of uninterrupted supply of clean drinking water is an important task for those who live in a private house.

This is necessary. through which precious liquid will come. To this end, many invite a team of professional drillers.

But you can create the necessary drilling installation with your own hands. Further, we will talk about the creation of a hydraulic tank at home.

The main types of drilling plants

Drilling rigs differ in their design due to the choice of various methods of creating a well. For example, a shock drill destroys the soil with a special cargo tied to a pyramidal support frame.

But the rotating drill is a much more complex design, but the deepening of the required size in the soil with its help is much easier.

By type of design, you can divide into several categories:

  • Shock-groken installations. The design is represented by a frame with the base of the pyramidal shape, to which the cable with a shell is reliably attached to the principle of operation of such an installation to a banal one: the load is lowered and rises as much as a number of times that will be required to create holes in the soil of the necessary depth.
  • Skin installations. Drilling is carried out using a screw breaking through the ground on the principle of rotation. In this case, the recesses dug during the drilling is not washed.

Attention! Keep in mind that drilling plants of this type are a design too complicated so that it can be created with your own hands: most of its functional elements are almost impossible to create in the absence of appropriate skills and tools.

  • Rotors. Rotary structures operate on the principle of hydraulics.
  • Manual structures of rotary type. These attitudes are considered the simplest to a greater extent for the reason that in their design they do not have an engine. Accordingly, the process of creating wells in the soil is carried out manually, which requires considerable physical costs. That is why such manual structures are very rarely used.

Advantages of home.made installation

Undoubtedly, a drilling plant for creating a water well has a number of advantages. These include:

In general, the assembly technology of various drilling rigs is almost the same (and this will be discussed a little further), but the working tool in structures of different types is radically different.

Therefore, to begin with, the technology of manufacturing the main mechanism (drill) in different structures should be considered and only after that proceed directly to the creation of the main frame and the working elements attached to it.

So, let’s consider in detail the most commonly used drill units (installation with a “glass” and a screw installation).

The so.called “cartridge” (“glass”) uses as the main working mechanism. If you want to make it yourself, then you will need only a pipe segment with a diameter of about 1 m.

When creating a suitable founding frame for such a drill installation, the dimensions of the “cartridge” are taken into account without fail.

The “cartridge” itself should have not only impressive dimensions, how much considerable weight for effective soil drilling.

Advice. On the bottom of the pipe, you can make pointings in the form of triangles. Thanks to this trick, you will increase the digging speed of the hole in the soil and the quality of loosening.

If you do not want to give the edges of the “cartridge” a triangular shape, make sure that they are sharp (if necessary, sharpen them).

“The glass” will be attached with a cable, so it is necessary to make several holes on the load (at the top). We fasten the cable and then catch it to a pre.prepared frame. Keep in mind that the length of the cable should be such that the “cartridge” can fall down and rise upstairs completely freely.

As an operating working mechanism uses a boat. For its manufacture, an ordinary metal pipe is also quite suitable. At the top of the pipe, make a screw thread, and on the bottom. a rod.type drill (the most convenient drill length is about 2 m).

Advice. 2-3 turns on the storm will be quite enough to create a water well of medium depth.

It is necessary to attach a pair of knives using the welding apparatus to the ends of the drill: they must be located in such a way that during the drilling process they plunge into the soil at some angle.

So that the design is convenient to work, weld part of the metal pipe to the tee (about 1.5-2 m long). The tee itself must be equipped inside a screw thread.

Separately, it should be said about the swivel, which is used in drilling plants as a compensator of counteracting the mobile part of the installation (drill) and the motionless part that supplies water. The device of this part is quite simple: a pair of flanges, partitions with sealing rubber rings, directly the case (made of a piece of a metal pipe) and a metal rod.

It should be noted that this part can be made independently only with a turning experience and the ability to make technical drawings.

MGBU assembly technology (small.sized drilling rig)

So, the working mechanism of the drilling installation is prepared, now you can proceed directly to the assembly of the entire structure. Keep in mind that you will need some tools for work: an electric drill, corner grinding, a welding machine, as well as a galvanized pipe, a lifting and a plumbing cross. Consider the process of assembling the design step by step:

  • Prepare the pipe segments to create the base of the drill installation. They will need to be attached to the drive and cross. At the ends of the pipe segments, cut the thread into a couple of centimeters.

Water in a personal plot is a necessary condition for a comfortable residence. A country house, cottage-if you have one of the listed, a water intake well you just need. And for its manufacture you will need a mini-brown installation with your own hands.

The assembly of the drilling installation will need to own locksmith skills and the ability to use the welding machine.

Features of options

Cons: the price of the issue depends on the complexity of the soil in your site and varies within 200. e. per pass 1 meter.

Motobur from a trimmer for grass

Another promising option seems to create a motorbike from a trimmer for grass with your own hands, which will significantly save. Such mowers for lawns are universally common. This allows you to find all the components you need for the future device without any problems.

It is important for Uhonor that the operation of all types of drills will be much more convenient if the stand for a motorcycle is involved in the process. With your own hands, it can be made only if the welding machine is available.

Drilling tool

As a drilling instrument in manual motorized carriers, screw drilling drills with a spiral (Rebining) are used, according to which the produced soil, destroyed by cutting knives of the drill screw, rises to the surface. Very rarely when drilling with manual motorized towers, column drilling tools are used. Sometimes, during geological selection of soil samples, hand.to.hand motoburs install tools for sampling. Depending on the type of soil and the season of use on drilling screws, various types of cutting knives of facilitating drilling are installed under different drilling conditions. The screw drilling method when using a motorcycle is designed to develop soft soils of 1, 2, 3 of category and partially soils of the 4th category (depending on the development conditions and the motorized motorcycle).

All of them are good, especially in specific situations for each situation. But when assembling a home.made motorcycle for economic work, it is better to take a factory reverse gearbox.

In the event that the drill stuck, rotating in one direction, then, changing the side of rotation on this gearbox, it can easily be removed.

Ice.beam from a trimmer for grass. the pros and cons of the device

Moto and Iceoburi have long become reliable assistants in the household. They are widely used not only for making holes in ice, but also to prepare a site with the aim of subsequent construction of a pile foundation. The presence of a drill makes it possible to save time and effort, however, the purchase of this equipment is far from affordable for everyone. In the event of a lack of funds, you can make a motorovers from a trimmer for grass. Homemade equipment is allocated by a simple device and does not require special care. In addition, homemade is distinguished by endurance and modest fuel consumption, which makes it possible to use it to make large holes in viscous clay or solid rocky soil.

Ice.beam from a trimmer for grass. the pros and cons of the device

Manufacturing a homemade ice discovery gives the owner of a trimmer for grass a number of important advantages.

  • Significant savings of money. on average, the assembly of a motorcycle will have to be spent 5-6 times less than on the purchase of the cheapest market model;
  • the possibility of using any details and mechanisms. when assembling a motor from a trimmer for grass, you can use any nodes designed to work in different conditions. A wide selection of mechanisms in the market gives the manufacturer the opportunity to assemble a motorbike from a trimmer for grass with your own hands, given, at the same time, its own capabilities and preferences;
  • Simplicity of the device. a home.made motorbike consists of a minimum number of details and mechanisms. At the same time, in its effectiveness it is practically not inferior to market analogues;
  • modest fuel consumption. compared to market analogues, to the operation of a home.made motorcycle, on average, 2 times less fuel goes.

In addition to an impressive list of advantages, the assembly of a motor from a trimmer for grass also has a number of disadvantages.

  • The need to study and understand the drawings. without a pre.prepared scheme, it will be almost impossible to collect an ice car from a trimmer for grass with your own hands;
  • The need for regular dismantling of the motor in order to subsequent installation on a trimmer for grass. those who use one engine for two economic units will face this problem. The purchase of an old but completely working engine from motorcycles will be able to solve it.

Another disadvantage may be the need for stopping when working with a motor from a trimmer for grass. Nevertheless, pauses must be done when using a low power engine.

The principle of operation of the unit

An electric drill is an electric motor and a shaft with a screw.type screw. When using such equipment, the hole in the ground will have even edges and a clear diameter of the screw. The direct process of drilling is carried out due to the fact that the screw has a very acute tip, as well as pointed screw.shaped blades. When the equipment is launched, the electric motor begins to rotate, transmitting its effort to the shaft, to which the screw is attached. Thus, drilling occurs.

Install a hard, stable coupling or flexible, if your drill is working on increased vibrations, so the flexible coupling will extinguish vibrations and blows.

Next, connect the worm shaft and gear of a 2-bit type.

When assembling the gearbox, leave a small hole between the details for the trouble.free filling of the oil.

Assembly of the ice discovery. in details from “A” to “I

To assemble an ice drift from a trimmer for grass, you will also need an engine that will drive the unit in effect. This is where the home trimmer for grass, which can be “lended” by the motor, come in handy. In order to exclude errors when assembling an ice discovery, you should carefully study the drawing of the unit. The scheme clearly shows what mechanisms of a motor.boom from a trimmer for the grass to connect to each other and in what sequence this must be done.

The diagram shows 3 options for the performance of a homemade ice discovery from a trimmer for grass. The first option is a screw motorbike, which consists of such elements:

The second option is a potted ice.beam from a trimmer for grass, the design of which includes the following details:

The third option is a motorbike from a trimmer for grass, equipped with semi.discise cutting knives. Its design includes:

Due to the fact that the motor from a trimmer for grass has a small torque, it means that it will be necessary to use gear ratio and lower the speed of rotation of the engine itself. Several gears placed in one case should be used as transmitting mechanisms. In order to reduce the engine speed on the primary shaft, you will need to install a small gear. At the same time, the secondary shaft is equipped with a large gear.

In order to make a motorbike from a trimmer for grass hard and stable, you need to make a strong frame to which the gearbox and motor will be attached. As controls, the handles should be used, which will also be mounted to the frame. Handles of the ice trammer from a trimmer for grass should be covered with rubber covers, which will not let the control organs slip in the hands of the owner.

The criteria that a good motorbike should have a do.it.yourself

If you decide to assemble a motorbike with your own hands, it is important to know that this is not gluing wallpaper or even brickwork, there is little to depend on your talent. In order to independently assemble a motorbike, you need to have basic turning skills and knowledge about the principles of work of elementary mechanisms. There are nothing complicated in the assembly of a motorcycle with your own hands, if you understand gearboxes. In this case, you can easily make a sleeve of the necessary diameter and make a reliable mount. Without the above skills and knowledge in the manufacture of a motorcycle, one cannot do. Therefore, if you do not have such competencies, you should contact friends with appropriate skills.

How to make ice car from a trimmer for grass?

The entire process of manufacturing a motorbike from a household trimmer for grass consists of several stages. The chances of collecting high.quality and durable equipment, which will regularly serve its owner for many seasons, depend on their sequence.

Rules for the manufacture of a screw mechanism

To make an ice car from a trimmer for grass with your own hands, its device must be equipped with a screw. In its form, this element resembles a screw necessary for a homemade for cutting an ice or soil layer.

To assemble a screw mechanism for a motor from a trimmer for grass, the designer needs a core, tip and a pre.made screw blade. The core must be made of maximum durable material. Most often, a metal thick.walled pipe is used to create this element. So that the motor.coil from a trimmer for grass can withstand the drilling of solid soils, the metal for the manufacture of the core will need to be tempered. this will prevent its deformation when twisting.

For the manufacture of a drilling blade, the designer will need steel of the 65g brand. In addition to high strength, this metal is easily treated with a pipeline.

The assembly of the tip for a motor from a trimmer for grass should be performed using carbide metal. The operator must apply grooves on the profile of the created part. this design will allow the motorcycle to plunge freely in any soil or ice, regardless of its thickness. On the back of the tip, you will need to install a shank that will serve as a connecting link between the drive gearbox and the connecting coupling.

Features of the choice of gearbox

To assemble an ice car from a gas station, the designer will need a gearbox. He plays one of the most important roles in the device device. using the Reducer of the ICE created, the force is transmitted from its standard shaft to another shaft, characterized by a reduced initial angular velocity and pre.increased rotation moment.

In the direction of continuous rotation of the built.in factory working element, built.in gearboxes for motobors are divided into the following types:

  • mechanisms with a shaft rotating along the hand of the watch;
  • gearboxes with a factory shaft rotating against the course of the arrow;
  • Mechanisms of the reverse or reversible type;
  • Inverse cast gearboxes. their second name. planar.
possible, trimmer, grass, motorbike, motorcycle

Do.it.yourself motorbots from a trimmer for grass with your own hands are best equipped with a reversing factory gearbox. This mechanism can rotate both by and counterclockwise. Thanks to this feature, when jaming a working drill in the soil, the operator will be able to extract it back without any problems.

Choosing the type of shaft location and gearbox assembly

At the next stage, the designer should choose the type of location of the standard engine shaft and the shaft of the drill itself. There are 2 options:

The most popular among manufacturers is a design with a parallel location of the shafts. This solution is highlighted in terms of self.handing and ease of repair.

After the preparation of components, you need to study the drawings that will help in the manufacture of the gearbox.

The procedure for the operator during the assembly of the mechanism should be as follows:

  • First you need to install a rigid stable coupling. When creating high vibrations by a power unit, the designer can use a flexible coupling. Thus, the part will soften the blows of the drill and extinguish the fluctuations of the internal combustion engine;
  • Then it is necessary to connect the worm shaft and an entire-metal gear of a 2-row type;
  • During the assembly of the gearbox, the manufacturer must leave a small hole between its details. it will be required for unhindered introduction of lubricants;

After the actions performed, the designer will receive a simple 1-speed gearbox that can continuously transfer the force of the power unit to the working body of a motorbike from a trimmer for grass.

Self.assembly of a motorcycle

For the consistent manufacture of a motorcycle from existing parts, the designer will require a scheme in which the installation sites of components should be indicated.

The assembly procedure should be like this:

  • First you need to disassemble a trimmer for the grass, taking off a bar with it with the cutting organs installed on it;
  • Then it is necessary to connect the gearbox to the motor by connecting the engine shaft and the shaft of the installed mechanism;
  • After that, the operator must install the working body of a homemade motor from a trimmer for the grass, attaching it to the gearbox with bolt clamps.

After assembling the equipment, it is necessary to test it. To do this, you need to season the fuel tank and start drilling soft loose soil. If, during this, extraneous sounds are not reported from the motor compartment of a trimmer for the grass, then you can proceed to drill hard soil or thick layer of ice.

How to make ice car from a trimmer for grass?

The entire process of manufacturing a motorbike from a household trimmer for grass consists of several stages. The chances of collecting high.quality and durable equipment, which will regularly serve its owner for many seasons, depend on their sequence.

Rules for the manufacture of a screw mechanism

To make an ice car from a trimmer for grass with your own hands, its device must be equipped with a screw. In its form, this element resembles a screw necessary for a homemade for cutting an ice or soil layer.

To assemble a screw mechanism for a motor from a trimmer for grass, the designer needs a core, tip and a pre.made screw blade. The core must be made of maximum durable material. Most often, a metal thick.walled pipe is used to create this element. So that the motor.coil from a trimmer for grass can withstand the drilling of solid soils, the metal for the manufacture of the core will need to be tempered. this will prevent its deformation when twisting.

For the manufacture of a drilling blade, the designer will need steel of the 65g brand. In addition to high strength, this metal is easily treated with a pipeline.

The assembly of the tip for a motor from a trimmer for grass should be performed using carbide metal. The operator must apply grooves on the profile of the created part. this design will allow the motorcycle to plunge freely in any soil or ice, regardless of its thickness. On the back of the tip, you will need to install a shank that will serve as a connecting link between the drive gearbox and the connecting coupling.

Features of the choice of gearbox

To assemble an ice car from a gas station, the designer will need a gearbox. He plays one of the most important roles in the device device. using the Reducer of the ICE created, the force is transmitted from its standard shaft to another shaft, characterized by a reduced initial angular velocity and pre.increased rotation moment.

In the direction of continuous rotation of the built.in factory working element, built.in gearboxes for motobors are divided into the following types:

  • mechanisms with a shaft rotating along the hand of the watch;
  • gearboxes with a factory shaft rotating against the course of the arrow;
  • Mechanisms of the reverse or reversible type;
  • Inverse cast gearboxes. their second name. planar.

Do.it.yourself motorbots from a trimmer for grass with your own hands are best equipped with a reversing factory gearbox. This mechanism can rotate both by and counterclockwise. Thanks to this feature, when jaming a working drill in the soil, the operator will be able to extract it back without any problems.

Choosing the type of shaft location and gearbox assembly

At the next stage, the designer should choose the type of location of the standard engine shaft and the shaft of the drill itself. There are 2 options:

The most popular among manufacturers is a design with a parallel location of the shafts. This solution is highlighted in terms of self.handing and ease of repair.

After the preparation of components, you need to study the drawings that will help in the manufacture of the gearbox.

The procedure for the operator during the assembly of the mechanism should be as follows:

  • First you need to install a rigid stable coupling. When creating high vibrations by a power unit, the designer can use a flexible coupling. Thus, the part will soften the blows of the drill and extinguish the fluctuations of the internal combustion engine;
  • Then it is necessary to connect the worm shaft and an entire-metal gear of a 2-row type;
  • During the assembly of the gearbox, the manufacturer must leave a small hole between its details. it will be required for unhindered introduction of lubricants;

After the actions performed, the designer will receive a simple 1-speed gearbox that can continuously transfer the force of the power unit to the working body of a motorbike from a trimmer for grass.

Self.assembly of a motorcycle

For the consistent manufacture of a motorcycle from existing parts, the designer will require a scheme in which the installation sites of components should be indicated.

The assembly procedure should be like this:

  • First you need to disassemble a trimmer for the grass, taking off a bar with it with the cutting organs installed on it;
  • Then it is necessary to connect the gearbox to the motor by connecting the engine shaft and the shaft of the installed mechanism;
  • After that, the operator must install the working body of a homemade motor from a trimmer for the grass, attaching it to the gearbox with bolt clamps.

After assembling the equipment, it is necessary to test it. To do this, you need to season the fuel tank and start drilling soft loose soil. If, during this, extraneous sounds are not reported from the motor compartment of a trimmer for the grass, then you can proceed to drill hard soil or thick layer of ice.

Necessary materials and tools

Creating an ice car from a trimmer for grass or motorcycles is quite simple. It already has an element rotating from the ICE. It is he who is the main detail of the benzargate.

For alteration, you will need a number of materials, tools.

  • Gearbox. This part is necessary to transmit the engine rotation to another shaft with low speed, but increased power. Gearboxes are rotating clockwise or against, reverse, planar. A reverse mechanism is suitable for ice discovery, which when jamming is able to rotate in the opposite direction. This will quickly extract it from the hole, because the ice on the rivers reaches a meter or more thickness.
  • Steel pipe for a screw mechanism, tip, screw blade. The shape of the screw resembles a screw that is easily bite into the ground or ice. The screw can be created independently from a thick.walled hardened pipe and a durable steel screw.
  • 2 conical gears.
  • 4 bearings.
  • Output shaft.
  • Gearbox.

For the manufacture of ice discovery, a lawn mower with an engine power is suitable for at least 3-4 liters.With. Her efforts are enough to make ice holes. A more powerful device is difficult to move in the field.

Read from a corner grinder manual saw with your own hands

Motobur made from a chainsaw with your own hands

The most popular option seems to be a motorbike from a chainsaw, since this variety has excellent performance that allows even hard types of soil to effectively develop. Wanting to make a device, it is necessary to prepare the necessary details in advance.

To make a home.made rope drill, you will need:

Be sure to read: characteristics of the milking apparatus AID-2

The latter is easiest to make using a standard hand drill and a metal pipe of a suitable diameter. The total length of such a screw should allow you to work comfortably with the ground. If you make the design removable, you get an excellent nozzle for a chainsaw.

A chainsaw is used for the manufacture of a motorcycle

Work description

Having decided to create an ice motorbark with your own hands, you should first of all make sure the compatibility of the selected gearbox and the saw engine. The speed of rotation of the future device should be small, otherwise the engine will quickly become unusable, and the soil will not be qualitatively drilled.

For assembly, you should adhere to the following instructions:

  • Make a screw by connecting a drill nozzle and a steel pipe.
  • Set the chainsaw engine reducing the velocity of the transmission mechanism.
  • Frame and screw should be securely connected to the engine and gearbox.
  • It is advisable to equip the unit with handles for 2 people, which will allow you to hold the tool if necessary when processing hard soil.

If you plan to make the tool maximally convenient for the user, it is recommended to transfer the gas button closer to the handles, this will work more comfortably.

How to make a motorbike from a chainsaw at home

Modern chainsaws are equipped with a powerful, hardy engine. The general characteristics of the tool allow you to work under almost any weather conditions. If you add a drill to this, in the end you get a practical, universal technique. DIY Motoburg will become an indispensable assistant in the household.

The manufacture of a gasoline requires a certain set of tools and materials, as well as competently compiled calculations. If problems may arise with the last task, it is recommended to consult an engineer or locksmith with the necessary skills. Do not rush with the assembly of the device. To ensure a high degree of safety during operation, you must carefully calculate and follow the plan.

Motobur from a chainsaw

Necessary tools and materials

  • a powerful motor from a modern chainsaw;
  • a mechanical gearbox with a reduced frequency on the output shaft;
  • directly drill;
  • angle grinder;
  • drill;
  • hollow metal rod;
  • Welding device.

The creation of a chainsaw drill does not imply that the latter will lose its main function. It will be enough to disconnect the drill from a home.made design to use the chainsaw in its normal mode.

Calculation of the compatibility of parameters

For the successful operation of the drill in the future, it is necessary to correctly determine the compatibility of the selected gearbox with the characteristics of the chainsaw motor. Modern motors are of good power, which means they create a large number of revolutions per minute. If the drill is spinning all the time at such a speed, the structure of the structure is not enough, and it will simply fail. In addition, in the manufacture of holes there is no meaning in such intensive work of the motor.

To choose a suitable screw gearbox, you should contact a specialist. Correctly made calculations minimize the risk of injuries in the future and generally optimize the work. In some cases, it is allowed to make a gearbox with your own hands, but the tested design is more reliable. In the manufacture of a motorbike from a chainsaw, saving at this stage is inappropriate.

The principles of assembly of the drill

Assembling a motorboon from a chainsaw begins with the manufacture of a durable case. To do this, it is necessary to measure a piece of a hollow metal rod 160 cm long. To bend the pipe in a rectangle with dimensions of 35 by 45 cm, you should make deep transverse cuts. If you rub the cuts of the corner grinder, it will be easier to achieve a right angle. Now all angles and connections must be fixed with a welding machine.

Then you need to make another similar frame, but smaller. only 10 by 10 cm. The manufactured parts are interconnected so that at least 30 cm remains between them. For assembling the drill, tubes of the same size are used, connecting the angle of one frame to the angle of another. Both frames should not remain in one plane. As a result, a peculiar pyramid should be obtained, inside which a gearbox needs to be placed.

Motor fixation

So that the saw can continue to fulfill its function, it is necessary to think over the BU with the removable engine. The possibilities will be limited if the motor is installed stationary. In order to remove it without problems, you should prepare a hole, in size, identical to the motor. A clamping frame with a high degree of reliability and a minimum of fasteners should be created-no more than a couple of nuts. All sizes depend on the specific model of the selected chainsaw and the features of the motor.

Motobur engine

How to make a motorbike with your own hands

Before starting the process of manufacturing a motorcycle, it is recommended to listen to the recommendations:

It is better to make a drawing of installation before manufacturing to clearly imagine the location of all unit nodes. It is necessary to calculate the power and dimensions of the tool: in the manufacture of a powerful device, a strong bed should be provided, possibly a trolley for moving. When choosing a gearbox, you should pay attention to its coincidence with the desired number of revolutions. If the number of revolutions is too large, it will be difficult to work with a motorcycle. When working with equipment, you need to observe security measures, protect your face and hands from stones, breeds, dust fragments, dust

When working with equipment, you need to observe security measures, protect your face and hands from stones, breeds, dust fragments, dust.

From a chainsaw

You can make a drill with your own hands from a chainsaw. For this, an old model is suitable, which is no longer suitable for performing its functions. The best option would be the old saw “Friendship”, “Stihl” or “Partner”. The engine from the chainsaw is fixed on the design of the frames, while the fuel supply system and the emergency stop of the unit are brought to the upper one.

To fix the drill, it is connected to the gearbox using a pipe. If necessary, in the future it can be replaced. You can make a motorbike from a chainsaw with your own hands with the possibility of vertical drilling. This is achieved by welding to the frame of metal rings, which are put on a vertical pipe made of metal. This design is put on a pipe with a drill, after which you can work.

From a trimmer for grass

For the manufacture of a mechanism for drilling the Earth, you can take an engine from a trimmer for grass. To lower the speed of rotation, it is recommended to use several gears united in a single case with the desired transfer number. The speed speed can be lowered if the gear of the primary shaft will be smaller, and the gear, which is attached to the secondary shaft, is more.

To create a sustainable motor from a trimmer for the grass, you will need a durable frame to which the motor and gearbox are attached. Handles are attached to the same frame to keep the tool. The screw is made of hardened steel, and the drill with a pointed tip.

From a drill

Motoburg can be made from a drill or a peorator. The manufacture of a motor.boom based on a pedorator is preferable, since it has a reverse that prevents the appearance of retroactive force in the event of jamming of the tool in the soil. For the manufacture of Buroim from a drill with a power and a torque of at least 2 kW., The following actions must be performed:

The unit made on the basis of the drill works from the electric network, which narrows the scope of application. However, such a tool can work at any temperature, unlike a chainsaw.

If you use your skills correctly, you can make a productive and powerful equipment that will help out more than once during construction or when performing landscape work

When using a motorcycle, it is important not to forget about safety precautions and get acquainted with any available materials about its proper operation

At the end, it is worth saying that the nozzle for a trimmer for grass for weeding helps to facilitate the work in the garden. The grass is mowed without much effort, giving the gardener the opportunity to engage in more pleasant things. Together with the weeding, some nozzles also give cultivation, saturating the soil with oxygen.

Manufacturers offer a wide selection of nozzles for weeding various designs and quality. In the choice, the main thing is to focus on the processed area, the power of the trimmer for the grass and the type of soil.