Miter saw metabo how to use

Miter saw: device, purpose and capabilities

A hand-held miter saw has a narrow purpose, and you are unlikely to be able to unfold boards with its help. Her tasks are slightly different. she can perform extremely short cuts. With its help, you can cut the board in half, align its end, or cut the end of the board at a certain angle. That, in principle, is all that she can, but, believe me, this is a lot. other saw equipment copes with such tasks much worse. Oh yes, I completely forgot that in addition to wood, depending on the equipment used, the miter saw can work with soft metals, plastic and, if necessary, with thin sheet iron, or rather with a profile made of it.

Miter saw capabilities

The universal miter saw has a rather complex design. it consists of two main units, which are not at all simple in design. This is a bed on which a rotary table and a movable cutting head with a powerful electric motor attached to it are fixed.

• Bed with a rotary table. As a rule, these two parts cannot do without each other. There is a guide on the bed itself, which ensures a fixed position of the workpiece. The miter saw table itself can rotate relative to the guide within 90˚ (45˚ in one direction and 45˚ in the other direction), thus providing a simple trimming of the workpiece in any direction without reinstalling the part.
• Cutting head. Installed directly on the turntable. it changes its location with it. For convenience in work, a graduated scale is applied to the side of the rotary table on the bed. by combining the table mark with a certain degree value, you can make cuts at any angle. And that’s not all. the head itself, or rather its cutting part, can be tilted left and right, thereby providing an oblique cut. In most cases, this tilt is performed in one or two fixed positions (30˚ and 45˚ to either side). Also, some models can be equipped with a special broaching mechanism. The miter saw with a broach allows you to cut workpieces much wider than its ordinary counterpart.

What is the design of the miter saw

Miter saw blades: what is the difference between them

There are not so many differences between the discs used on the miter saw, and the main ones are the fit and outer diameter, as well as the geometry of the cutting tooth. If everything is more or less clear with the size of the discs (the bore can be either 25mm or 30mm, and their outer diameter is 210, 250 and 305mm), then the geometry of the tooth should be dealt with in more detail.

• You should pay attention to the size of the tooth. the larger it is, the rougher the cut will be. A disc with a large tooth is unlikely to be able to cleanly cut laminated, varnished or painted workpieces. for these purposes, you need to purchase a disc with a fine tooth. Also, a small tooth showed itself well when working with an aluminum profile. In general, in this regard, saw blades for a miter saw can be divided into three types: for longitudinal cuts, for cross cuts and for fine cuts, which, as a rule, are universal.
• When it comes to mass production or working with thick workpieces, you need to pay attention to the presence of thin slots on the disk. in fact, these are temperature compensators, whose task is to maintain a stable disk size when it heats up. In addition, such discs are less noisy.

Miter saw blade photo

And a few words about the enterprises that produce miter saws for wood. Bosch and Makita are leaders in nearly all power tools, and their miter saws are no exception. The tools Metabo, Hitachi, DeWalt also performed well in practice. If we talk about domestic miter saws, then here we can note the Corvette tools. In general, there is plenty to choose from. the main thing is just not to miscalculate the possibilities.

Bosch manual miter saw photo

That is, in principle, everything you need to know about a tool such as a miter saw. Buy, use it and remember that this tool is quite dangerous. do not forget about safety precautions and when working, always be extremely collected, and most importantly sober!

A miter saw is a tool designed to cut workpieces at a specific angle. It makes it possible to make a perfectly even cut at any given angle. The saw can be used for sawing various materials such as wood, plastic, aluminum.

The area of ​​use of trimming machines is quite large: they are used in the manufacture of furniture, assembly and repair work, and carpentry. The main field of application of miter saws is work related to the production of window frames and the laying of floors.

If you need to select and purchase a miter saw, first you need to decide on the volume of work performed, the frequency of use and its direct purpose. If for one-time home use, then it is not necessary to buy an expensive professional-class typewriter. you can get by with a budget option. For daily use, you need a more serious car. You should also pay attention to the following features:

• Maximum dimensions of workpieces;
• Availability of electronic adjustments;
• Base material;
• Limits of tilt and swivel angle adjustment;
• The presence of a laser;
• Broach function.

metabo Compound miter saw, model C 10FCG (S) unboxing and review! #oldguysmatter #metabo miter saw

Modern miter saws. applications

Modern trims can be used for cutting wood and metal, as well as plastic and composite materials (chipboard, fiberboard, plywood, laminate, etc.). This makes this tool a popular equipment in wood and metal processing enterprises.

Before you understand what a miter saw is, how to use it in everyday life and in the carpentry industry, you should get acquainted with its main design features.

Like the closest “relatives”, circular saws, cross-cutters are equipped with a saw head tilted to the left and right with a disc (smooth-edged or serrated). For operator safety, the saw equipment is placed in a protective cover that automatically opens the saw blade when starting work.

The start of the tool is carried out by the start button, which activates the operation of the gearbox with an electric motor. The tool can be purely manual, with a convenient bracket-shaped handle, it can have a table-top base or be installed on a workbench with rubber-knob feet that prevent the machine from sliding on the floor.

In contrast to the circular, not only the saw head tilts at the trimming, but also the working surface of the table (bed). This provides a wide field for the joiner who can create different types of cuts in the material to be cut by tilting both the saw head and the work table. That is why in the technical parameters of miter saws there can be several values ​​of sections (width and depth of cut) with different positions of the head and bed.

Also, in contrast to the circular saw, in the trimming the saw head is fed to the workpiece, and in the circular saw the workpiece is moved to the fixed tool. The axis of the saw blade in the miter saw is located above the plane of the work table: to make a cut, the saw is lowered, crossing the workpiece and the surface on which the workpiece is fixed.

Miter saws are most in demand at factories for the manufacture of floor coverings, doors, furniture. Taking into account large-sized workpieces in furniture production, in order to securely fix them to obtain the most accurate and accurate cut without chipping, bevels and burrs, a crosscut saw with a broach is used here.

Cutting finishing materials at an angle is, frankly, not an easy task, and almost all people have problems with its solution. Meanwhile, most of the finishing materials require just such an approach to their installation, for example, lining, baseboards, baguettes and even metal structures assembled from a profile pipe. In general, there are many such materials, and their diagonal cutting has to be solved, sometimes even with very high accuracy. In this article, along with stroisovety.org, we will explore a tool such as a miter saw to help you tackle the task of diagonal trimming. We will get acquainted with the device of this tool, the evaluation criteria, which will allow us to purchase a model suitable for work and we will deal with the saw blades used with this tool.

Electric miter saw photo

Electric miter saw: nuances and selection criteria

The question of how to choose a miter saw can be solved by adhering to five small rules.

To begin with, you must decide on its purpose and operating conditions. What do you need it for? What kind of work, and most importantly, how much do you plan to do with it? If you are purchasing a miter saw for home use and do not plan to perform complex operations, then it is quite possible to get by with a simple tool with a basic set of additional functions. If we are talking about the professional use of the miter saw and its daily use, then, of course, you need to choose the extended version of this tool with a full set of additional options. You can consider the option of purchasing a so-called combined miter saw, which is equipped with an additional work table in the upper part of the cutting head, allowing it to be used as a stationary circular saw.

Miter saw for wood photo

How to choose a miter saw

Naturally, when choosing a miter saw, it will not be superfluous to take into account the power of this tool, as well as the speed of rotation of the blade. In most cases, these values ​​are calculated by the manufacturer and are optimal. A household tool will have a lower power than a professional one, but the rotational speed of the disk is almost always the same, which is due to the need to make a clean and even cut.

Miter saw universal photo

METABO MITER SAW REVIEW!

Combined saws

Combined saws are also available on the market. They combine two tools in one. a miter saw and a saw saw. It is based on the same miter machine with an additional sawing table. The attitude towards them is rather skeptical, professionals believe that the tool should be designed for one type of work. However, the common user is increasingly opting for combination saws.

How to use a miter saw

A hand, table or machine miter saw is a professional sawing power tool used for miter, longitudinal, transverse, oblique and oblique cuts. Its full name is a miter saw, this operating tool received for the ability to perform an ultra-precise and ultra-fine accurate saw operation. the so-called “mustache joint”, when the joining of two parts with angled edges is as tight as possible (for example, two plinths in the corner premises). In general, most often, in the everyday life of masters, a miter saw is simply called a miter saw.

Device

The miter saw device is pretty simple. It consists of an operating unit and a control unit (handle with start button).

The working unit consists of a gearbox with a motor. Two types of motors are used on trimming machines: commutator and asynchronous. The collector ones have a high torque, but they require constant maintenance and replacement of brushes. Asynchronous motors do not have brushes, they are less noisy and serve for a long time. The engine is most often located to the right of the working disc, so as not to block the view.

To transfer torque from the engine to the disk, two types of transmission are used. gear and belt. The gear transmission eliminates slippage at high loads, the belt makes less noise and dampens the vibration of the disc. Over time, the belt wears out and needs to be replaced. There is also a direct drive miter saw. The absence of rubbing parts is good for reliability.

Bevel cuts require the work surface to be rotated. The table rotates at an angle of at least 45 degrees, often the angle of rotation is greater, up to 60 degrees. Often, adjusting mechanisms are equipped with clamps for standard tilt angles (0, 15, 30 and 45 degrees).

An added benefit is that the cutting disc can also be tilted. The standard tilt angle is 45 degrees, but on some models the angle reaches 46 or even 47 degrees.

One of the most important functions of the miter saw is the cut depth stop. It is used for grooving or facing a workpiece.

In miter saws, the number of electronic adjustments is kept to a minimum. Most models do not even have a speed controller, but the presence of such an option allows, by reducing the speed of rotation, to better control the process and adapt to a certain material.

Even less often, the function of maintaining the speed under load is used in saws. With strong pressure, the tool speed drops sharply, at this moment the electronics should work and stabilize the speed. This allows you to significantly improve the quality and cutting speed. Experienced craftsmen do well without this feature.

Some saws use a “laser” to improve quality and ease of use. It makes it possible to see the intended cutting line, and not estimate “by eye”.

There are also additional options. One of them is the desktop extension. It is essential when working with long workpieces. The standard length of the extended table is half a meter, but there are also more. Other accessories include ties, clamps, stands for easy installation and use.

Any miter saw creates a lot of waste. Dust, sawdust and debris contaminate the work surface, interfere with the work and safety of the user. In modern saw models, there are several options for collecting dust. Waste can be collected in a dust bag or vacuum cleaner. To connect the latter, there is an additional pipe.

Order in one click

The Metabo KGS 254 M miter saw is an indispensable tool for finishing work. Designed for sawing plastic, wood, non-ferrous metals. An updated version of the legendary saw that entered the market in the fall of 2014.
The saw has become lighter, more comfortable and more ergonomic. The design features of Metabo KGS 254 allow you to cut workpieces of various sizes and at different angles, make cuts of the same depth for serial production of workpieces.

• The powerful engine allows to carry out work of increased complexity and has a large motor resource.
• Metabo KGS 254 is equipped with Stop Blocks, with which workpieces of the same size are cut quickly and efficiently.
• The saw blade is mounted on two strips and can move freely (feed function), which allows cutting material up to 305 mm.
• A special stop allows you to make an incision of the same depth, which is very convenient for serial production of workpieces.
• The exact cutting angle can be set quickly and easily thanks to the easy-to-read scale.
• The aluminum table is die-cast and is highly durable, which in turn increases the overall service life of the Metabo KGS 254 M.
• The laser indicator of the cutting line and illumination allow for the most accurate incision. The laser and LED lamp are mounted on top of the saw cover, which eliminates the ingress of chips.
• Comfortable work with long workpieces is ensured by the possibility of extending the table, and this does not require additional tools. The extenders themselves can be removed and placed at any distance from the instrument.
• Convenient holder for winding the power cable, ergonomic design make transport and storage of the saw as easy as possible.
• Redesigned dust extraction system. swarf is captured directly at the disc exit from the material, which significantly increases the efficiency of the entire dust extraction system.

Miter saw Metabo KGS 254 M

Equipment

Specifications

elder (07/18/2019)
Rating:

Having picked Metabo, I’ll give a jib saw and I’ll give her more satisfaction. And the qia came with a crooked table. Rozcharuvannyu not bulo kіntsya. The center of the left part of the boulevard is 2 mm. By submitting the service on Monday. On Tuesday, the phone was answered, the problem was violated, and on four evenings they took it. The same for the service of the service staff is firm p’yatirka. We will marvel at the yak tsia shaitan-machine bude dali.

Alexander (09/27/2017)
Rating:

Good day. Tell me if it is possible to install discs with an outer diameter of 260 mm on this facing?

Metabo Shop’s answer
Good afternoon, Alexander.
No, a disc with a diameter of 260 mm will not fit into a standard casing.

Alexander (05/31/2017)
Rating:

Hello. Please tell me if the rotary table and bed with extensions should be in the same plane. I have a turntable a millimeter higher than the bed, and the bed is higher than the extensions. In total, all three elements are at different heights. You have to press the workpiece with your hand near the saw itself. I also could not adjust the backgauge, which would turn out to be 90 degrees. He took it off, and he was all screw. I just bought it! This is how it works, but there is no way to adjust the angles due to the difference in the heights of the platforms and the screw in the backgauge! Is this a warranty case? can all this be eliminated or is it a metabo quality? And more. The saw only cut a few pieces of wood. It is practically new and already contact in the laser is interrupted sometimes.

Miter saw: device, purpose and capabilities

A hand-held miter saw has a narrow purpose, and you are unlikely to be able to unfold boards with its help. Her tasks are slightly different. she can perform extremely short cuts. With its help, you can cut the board in half, align its end, or cut the end of the board at a certain angle. That, in principle, is all that she can, but, believe me, this is a lot. other saw equipment copes with such tasks much worse. Oh yes, I completely forgot that in addition to wood, depending on the equipment used, the miter saw can work with soft metals, plastic and, if necessary, with thin sheet iron, or rather with a profile made of it.

Miter saw capabilities

The universal miter saw has a rather complex design. it consists of two main units, which are not at all simple in design. This is a bed on which a rotary table and a movable cutting head with a powerful electric motor attached to it are fixed.

• Bed with a rotary table. As a rule, these two parts cannot do without each other. There is a guide on the bed itself, which ensures a fixed position of the workpiece. The miter saw table itself can rotate relative to the guide within 90˚ (45˚ in one direction and 45˚ in the other direction), thus providing a simple trimming of the workpiece in any direction without reinstalling the part.
• Cutting head. Installed directly on the turntable. it changes its location with it. For convenience in work, a graduated scale is applied to the side of the rotary table on the bed. by combining the table mark with a certain degree value, you can make cuts at any angle. And that’s not all. the head itself, or rather its cutting part, can be tilted left and right, thereby providing an oblique cut. In most cases, this tilt is performed in one or two fixed positions (30˚ and 45˚ to either side). Also, some models can be equipped with a special broaching mechanism. The miter saw with a broach allows you to cut workpieces much wider than its ordinary counterpart.

What is the design of the miter saw

Miter saw: device, selection principles and discs used for work

Cutting finishing materials at an angle is, frankly, not an easy task, and almost all people have problems with its solution. Meanwhile, most of the finishing materials require just such an approach to their installation, for example, lining, baseboards, baguettes and even metal structures assembled from a profile pipe. In general, there are many such materials, and their diagonal cutting has to be solved, sometimes even with very high accuracy. In this article, along with stroisovety.org, we will explore a tool such as a miter saw to help you tackle the task of diagonal trimming. We will get acquainted with the device of this tool, the evaluation criteria, which will allow us to purchase a model suitable for work and we will deal with the saw blades used with this tool.

Electric miter saw photo

Electric miter saw: nuances and selection criteria

The question of how to choose a miter saw can be solved by adhering to five small rules.

To begin with, you must decide on its purpose and operating conditions. What do you need it for? What kind of work, and most importantly, how much do you plan to do with it? If you are purchasing a miter saw for home use and do not plan to perform complex operations, then it is quite possible to get by with a simple tool with a basic set of additional functions. If we are talking about the professional use of the miter saw and its daily use, then, of course, you need to choose the extended version of this tool with a full set of additional options. You can consider the option of purchasing a so-called combined miter saw, which is equipped with an additional work table in the upper part of the cutting head, allowing it to be used as a stationary circular saw.

Miter saw for wood photo

How to choose a miter saw

Naturally, when choosing a miter saw, it will not be superfluous to take into account the power of this tool, as well as the speed of rotation of the blade. In most cases, these values ​​are calculated by the manufacturer and are optimal. A household tool will have a lower power than a professional one, but the rotational speed of the disk is almost always the same, which is due to the need to make a clean and even cut.

Miter saw universal photo

Miter saw blades: what is the difference between them

There are not so many differences between the discs used on the miter saw, and the main ones are the fit and outer diameter, as well as the geometry of the cutting tooth. If everything is more or less clear with the size of the discs (the bore can be either 25mm or 30mm, and their outer diameter is 210, 250 and 305mm), then the geometry of the tooth should be dealt with in more detail.

• You should pay attention to the size of the tooth. the larger it is, the rougher the cut will be. A disc with a large tooth is unlikely to be able to cleanly cut laminated, varnished or painted workpieces. for these purposes, you need to purchase a disc with a fine tooth. Also, a small tooth showed itself well when working with an aluminum profile. In general, in this regard, saw blades for a miter saw can be divided into three types: for longitudinal cuts, for cross cuts and for fine cuts, which, as a rule, are universal.
• When it comes to mass production or working with thick workpieces, you need to pay attention to the presence of thin slots on the disk. in fact, these are temperature compensators, whose task is to maintain a stable disk size when it heats up. In addition, such discs are less noisy.

Miter saw blade photo

And a few words about the enterprises that produce miter saws for wood. Bosch and Makita are leaders in nearly all power tools, and their miter saws are no exception. The tools Metabo, Hitachi, DeWalt also performed well in practice. If we talk about domestic miter saws, then here we can note the Corvette tools. In general, there is plenty to choose from. the main thing is just not to miscalculate the possibilities.

Bosch manual miter saw photo

That is, in principle, everything you need to know about a tool such as a miter saw. Buy, use it and remember that this tool is quite dangerous. do not forget about safety precautions and when working, always be extremely collected, and most importantly sober!

Miter saws Metabo

Power 1350 W
Speed ​​5000 rpm
Saw at 90 ° 120/65 mm
Saw at 45 ° 80/45 mm
Weight 9.4 kg

Power 1500 W
Speed ​​5000 rpm
Saw at 90 ° 305/65 mm
Cut at 45 ° 205/36 mm
Weight 13.5 kg

Li-Power battery 18 V
Speed ​​5000 rpm
Saw at 90 ° 120/65 mm
Cut at 45 ° 80/45 mm
Weight 9.6 kg

Power 1700W
Speed ​​3800-5500 rpm
Saw at 90 ° 305/65 mm
Cut at 45 ° 205/36 mm
Weight 13.5 kg

Power 1800 W
Speed ​​4500 rpm
Saw at 90 ° 305/92 mm
Cut at 45 ° 205/47 mm
Weight 16.3 kg

Battery 18 V Li-Power
Speed ​​4200 rpm
Saw at 90 ° 305/65 mm
Cut at 45 ° 205/36 mm
Weight 13.8 kg

Power 2000 W
Speed ​​3700 rpm
Drank at 0 ° 150/102. 200/80 mm
Cut at 45 ° 130/45 mm
Weight 17 kg

Power 2000 W
Speed ​​3700 rpm
Saw at 0 ° 305/105 mm
Cut at 45 ° 205/67 mm
Weight 19.6 kg

Li-Power battery 18 V
Speed ​​5000 rpm
Saw at 90 ° 120/65 mm
Saw at 45 ° 80/45 mm
Weight 9.6 kg

Tool set: Miter saw Metabo KGS 216 M
Metabo KSU 251 table

Tool set: Miter saw Metabo KGS 254 M
Table Metabo KSU 251

Power 2000 W
Speed ​​3700 rpm
Saw at 0 ° 150/102 mm
Saw at 45 ° 115/45 mm
Weight 22 kg

Battery 18 V Li-Power
Speed ​​4200 rpm
Saw at 90 ° 305/65 mm
Cut at 45 ° 205/36 mm
Weight 13.8 kg

Power 1800W
Speed ​​2200-6300 rpm
Saw at 90 ° 305/72 mm
Saw at 45 ° 215/42 mm
Weight 16.1 kg

Tool set: Miter saw Metabo KGS 305 M
Table Metabo KSU 251

Power 1800W
Speed ​​2200-6300 rpm
Saw at 90 ° 305/72 mm
Cut at 45 ° 215/42 mm
Weight 18.3 kg

Tool set: Miter saw Metabo KGSV 72 Xact
Metabo KSU 251 table

Tool set: Miter saw Metabo KGS 305 M
Table Metabo KSU 401

Battery 18 V LiHDr
Speed ​​4200 rpm
Saw at 90 ° 305/65 mm
Cut at 45 ° 205/36 mm
Weight 13.8 kg

Miter saws from Metabo are high-quality professional-grade tools designed for sawing work during renovation, construction or interior decoration, as well as efficiently working in a carpentry workshop or furniture workshop.

Depending on the model, the Metabo miter saw can be equipped with such functions as feed, fixing the cutting depth, laser indicator of the cutting line, tilting the saw head to one or two sides, table extensions, etc. Thanks to their excellent functionality and high reliability, Metabo miter saws are highly regarded by professionals.

Mitre Saw Unboxing and setup for Fine Tuned Perfect Cuts

Cordless wood trimmer 185mm Yato YT-82816

Miter saw 305mm for wood JET JSMS-12L

End saw for wood 210mmProton PDT-210

Miter saw for wood 210mm Utool UMS-8

Saw head.

Overall unit consisting of a saw blade, an electric motor, protective covers, a tilt mechanism, a control handle with a control button.
To perform the trimming, that is, the connection of wooden parts along the entire width, they must be cut at 45 °.
All feed miter saws can tilt the blade 45 ° to the left from vertical. Some in both directions. This is more difficult to implement, due to the location of the engine, which, when installed laterally, will rest against the workpiece, leaning to the right.
On professional angle cutters, some tilt angles are fixed: 0, 15 °, 22.5 °, 30 °, 33.9 ° and 45 °, and the maximum is 47 ° or 60 °.

Carbide wheel and protection device.

Outside diameters of the most popular tooling: 210, 255 and 305 mm. The soldered circle rotates at a speed of several thousand revolutions, so it is always closed from the user’s side.
The protective cover consists of two parts. In the standard version, the upper fixed part, narrow aluminum. Bottom movable wide, made of transparent plastic. The lowering and raising of the cover occurs automatically, following the movement of the saw unit.
On miter saws with a pull, a roller is usually placed from the left edge of the lower part of the protective element, which moves parallel to the groove on the work table along the workpiece.

The tooling is changed with a key while the spindle lock button is pressed, or with a quick-clamping nut.

Lever.

Usually one located in a horizontal plane, but there can be two (the second is vertical next to or behind, on the broaching mechanism). A power button is installed on the handle and it also serves to grip during transportation.

Dust extraction system.

All wood miter saws are equipped with sawing waste collection pipes.
The sawdust can be collected autonomously in a bag. This is facilitated by the closed form of the disc protection: when it rotates, the air flow captures most of the sawdust and, passing around the circumference of the casing, throws them into the branch pipe located at the rear.
On other side trims, the dust removal system is organized through a groove in the turntable. The channel connects to the bag installed at the bottom of the turning unit.
Almost all wood waste can be collected only by installing a chip suction and using two pipes.

Wood trimmer with broach 255mm Yato YT-82173

Combined miter saw 250mm Einhell Home TH-MS 2513 T

Reliable miter saws for the construction site and workshop

The miter saws from Metabo are built on the basis of many years of experience. The program includes over 10 saws for a wide variety of applications. The rated power consumption, depending on the model, varies from 1350 W to 2200 W. You can choose saw blades with diameters from 216 mm to 315 mm, this determines the maximum width and height of the part. The large miter and miter saw KGS 315 Plus provides a cutting width of 320 mm at a cutting depth of 120 mm when the saw blade is set at a 90 ° angle. Of course, using the feed function, which is integrated into almost all miter saw models. For mobile use, we recommend a compact lightweight with a carrying handle, which hardly weighs more than 10 kg. The KGSV 72 Xact SYM saw is one of a kind, which is a combination of a panel saw and a rack saw with a symmetrically adjustable stop system. Real Progress in Precision Sawing Operations with Time Savings for Floor Installers.

Miter saws

• 20
• fifty
• one hundred

• 20
• fifty
• one hundred

Features for maximum sawing comfort

In all miter saws, the swivel disc can be rotated on both sides. The tilt of the saw head is also a standard feature, in some models even to the right and to the left. Bevel cuts, curved cuts and combined cuts / cuts are possible without any problem. With a variable speed miter saw, aluminum and plastic can be sawed without problems at the appropriate speed. The integrated cutting laser and extendable table extensions are standard equipment at Metabo, as well as the chip suction option. Other properties are indicated in the description of individual products.

Miter saws / Miter and miter saws

Large range of miter saw blades

From rough cuts of construction timber to precise, clean cuts in complex workpieces, saw blades are available in all required diameters and tooth systems. Special blades for plastic and aluminum round off the comprehensive range of accessories for miter saws. Stands can be used for sawing while standing. A lightweight and sturdy stand, possibly with casters, for mobile use. a valuable companion on the jobsite. For sawing long workpieces, the miter saw holder KSU 401 can be extended to a width of up to 4 meters.