One Hand Fishing Line Do Not Reel To Reel

Beginner fishers will surely fill up a lot of cones until they learn all the secrets of how to equip a fishing rod or spinning. One of the first questions that will have to be answered is: “how to wind a fishing line onto a reel?”.

If the winding of the fishing line on the reel of the rod was initially improperly done, then be sure fishing will be damaged. Another reason to spoil fishing is to wind an old and unreliable fishing line, which will break at the most inopportune moment.

How, where and how much

There are questions, answering which everything will become clear.

How much fishing line do you need to wind

Winding fishing line on the reel should not reach the edge of 1-1.5 mm, so as not to fall down. But the distance can increase to 2-2.5 mm, it depends on the design of the reel, its quality and the diameter of the fishing line. Therefore, sometimes, if there is a constant discharge of fishing line, simply increase the distance to the side by 0.5 mm, perhaps this will solve the problem.

How tight it is to reel

When winding a monofilament or braid, it is necessary to observe the middle ground. It is not necessary to wind it with excessive force, but it is especially important to wind it lightly. You wind it tightly. The fishing line will soon come to an end, it will quickly break. You wind it slightly. The top layer of fishing line when casting with bait will crash into the remaining layers. “beards” cannot be avoided.

Although if you are not fishing line zhAL-KO, you can wind tight.

Unwinding direction

The line should be wound on the reel in the same direction as on the reel. In the opposite direction can not be wound.

How to rewind a cord from a reel without a special machine

For proper winding, you need to conveniently position the bobbin with which you will unwind. To prevent this bobbin from spinning, it must be fixed. Ideal if you put it on a pencil or screwdriver wrapped with adhesive plaster. Give the pencil to the assistant. The bobbin should be in the same plane with the reel, less fishing line is twisted. After rewinding, close the forestry arm.

One Hand Fishing Line Do Not Reel To Reel

We use a pencil

In general, there are many ways to fix the bobbin. Someone clamps with their toes, some use a drill to reel in quality.

If you twist without an assistant, then the winding of the fishing line on the reel often happens with twisting, so you need to constantly turn the bobbin and make sure that there is no torsion. When spinning the fishing line there will be “beards” during casting. The winding density can be controlled by holding the fishing line with your fingers in front of the reel. Only the fishing line must be held with foam rubber or a cloth, someone just puts on a rag glove. Otherwise, cut your fingers or the fat from your fingers will fall onto the fishing line, which is also unacceptable if it is sinking. This is true in match fishing.

How to snap

You can tie the fishing line to the spool with one of the nodes. On high-quality reels there is a special stopper for which you can simply refill the fishing line. In general, how to tie a fishing line to a reel you choose to your liking.

Rewinder

You need to know that in nature there is such a device as a rewinder. With it, fishing line on the reel is wound easily and simply. One drawback is the cost of this fixture is impressive. But our craftsmen make such machines with their own hands.

The shows how such a device works:

Coil

Coils come in several forms. Therefore, you can consider how to reel in one form or another.

  • On multiplier reels, it is impossible to simply change the spool, for which the fishing line or braid was refueled in advance.
  • On inertial spools are all different, so this operation also will not work.
  • On inertialess to wear another spool with a wicker is quite real.

Inertial

About 100 meters are placed on an inertial, ordinary “grinder”, so if you buy a fishing line in an uncoiling of 100 meters, then it is calculated that it will just enter as a whole.

For a spinning rod or feeder, where there are flow rings, the fishing line on the “grinder” is wound directly on the assembled fishing rod. If you put a reel with wound fishing line, you will cling to the “beard” when casting. Therefore, it is necessary to decompose the spinning and pass the line through all the access rings. Start with the smallest ring. Fold away the stowage arm. Then secure the fishing line to the spool, tie a knot or a stopper. First, make several turns evenly by hand, then start twisting the handle of the “grinder”. The fishing line will be wound.

Often the flaws of the “grinder” are wrongly blamed on the fishing line being wound. If you bought a not very successful “grinder”, then humps may form, a failure will appear at the front side or there will be a reverse cone. With proper winding, the fishing line should lie exactly as on a spool of thread.

Multiplier

Everyone knows that a multiplier reel is a type of inertial one. It is very important to use a fishing line of the thickness that is designed specifically for this model.

Look at the how to wind fluorocarbon onto a bobbin reel:

Some fishermen make a mistake when tying braids or monofilament to a bobbin reel. They pass it through the distant holes in the spool, which leads to inhibition. Only need to be tied for holes that are close. Fill the fishing line into the bobbin reel as follows:

  • Bind fishing line with any knot.
  • Insert the reel into the spinning rod, and pass the braid through the right ring.
  • Tighten the clutch and axial brake.
  • Use your fingers and a cloth to control the tension of the fishing line.

Inertialess

The thickness of the line should be the same as indicated on the reel. If the thickness of the braid or monofilament is greater, then it will be very difficult to fill it. With a smaller diameter, solid beards will appear during casting. As a result, you will lose part of the braid or monofilament. Each inertialess reel is made not only for a specific diameter of the fishing line, but can also accommodate a certain amount of braid or monophile. These parameters are indicated in the coil passport. They are different for different manufacturers. So read the instructions carefully, translate it, even if it is in Japanese.

Well-known manufacturers are constantly struggling with twisting. To do this, they will improve the coil, namely the logger roller. The better the coil manufacturer, the better the styling.

Winding fishing line on an inertialess reel is performed “cross” or “turn to turn”. This installation is very high quality. But do not forget that you do not need to fill the spool “to the eyeballs”. Leave 1-1.5 mm.

Leave 1-2 mm to the edge of the spool

When buying an inertia-free coil, you need to set up your styling profile. Profile adjustment is very important. There are three winding methods and you can configure them:

  • Cylindrical.
  • Inverse cone.
  • Straight cone.

In the inertialess coil, 4-6 washers are provided with which you can adjust the styling. These washers have different thicknesses.

In the picture, the first option is the cylinder, the second option is the inverse cone. The third is a straight cone:

Winding

Coils with front and rear clutch have different settings, they are configured differently.

Front clutch

Washers. Gaskets are located on the axis where the spool mount is located. By placing or removing pads, you can adjust the height of the spool. Straight cone. Higher spool fit. Reverse cone is lower. By default, the setting is cylindrical.

With rear clutch

The washers are located inside the spool. Have to unwind the coil, and you will see these washers. But with a rear clutch, a higher landing will give a reverse cone, a lower one will wind a straight one. The opposite is true. The adjustment will be different.

In the, look at winding the braid on an inertialess coil:

Quality spool filling

Often the reel holds more fishing line than you have. In order for the coil to be completely filled, you need to attach a reel under the fishing line. It can be a band-aid or tape.

Backing

Another option is a less quality fishing line called backing. The amount of backing is determined empirically. First, shake the main fishing line, then backing tied to it. Thus, determine which piece of braid you need. Then the reverse process of rewinding to the spare spool. Finally refueling fishing line into the reel begins with backing.

When using backing, the correct knot is very important when linking fishing line with braid, or just fishing line with fishing line.

Unlike electrical tape, backing from fishing line dries faster and therefore does not rot. In addition, with adhesive tape or electrical tape it is not possible to achieve accuracy in filling the spool.

Counter

In multiplier reels, used mainly for trolling, there is a built-in fishing line counter. But such a device is not in all models. Typically, the description indicates equipment counter. When spinning the drum, the counter fixes how many meters have already been lowered or wound up. Having determined empirically to what depth we need to lower the bait, you are already clearly delivering it to a given depth.

Previously, they did not use the counter, since it simply was not there. If there is no counter, then you can simply mark the line every meter or two with a marker. The problem with determining the depth is removed automatically.

Trolling counter

Sign of the people: If you dreamed that you went fishing, it means that you want changes in your life!