Paint Remover Drill Sets
Remove old paint from the walls quickly will help the nozzle on the drill with his hands
When we ordered the repair of the bathroom and toilet latrine. closet. closet). a room for the performance of natural needs (urination, defecation and antiperistalsis) in khrushchevka, then the workers faced a difficult problem. Removing old stained paint is a common name for a group of colored dyes intended for direct use in one way or another in the home on concrete walls is not an easy thing to do.
It used to be commonplace to paint walls with oil paint not only in the bathroom and toilet, but also in the kitchen. In the kitchen, we did the repairs themselves and did not remove the paint, and just cleaned of dust and glued washable wallpaper type of construction finishing materials for lining walls and ceilings inside the premises. The wallpaper is still holding up (it’s been 4 years).
See how it was not easy for us to repair a set of measures to restore the working or serviceable condition of an object and / or restore its resource in the bathroom, bathing or taking medical procedures and the toilet.
You can remove the paint with an axe, a spatula. But the process can take a long time. As a result, the headache of noise, not only the owners, those who make repairs, but also the neighbors.
How to speed up the process and get the paint off the walls faster? There is a good way to do this.
What nozzles are available for the peorator
After the invention of the peorator, the functionality of this power tool is expanding every year. It is achieved by extending the functionality by producing different kinds of nozzles that can not only drill, but also chisel, tap, destroy, drill, knead, chisel, hammer, etc.п. All these manipulations are realized by special devices. The following types of nozzles are available for the peorator:
- Drills. for drilling holes in concrete and other similar materials
- Chisels. special appliances for removing tiles and crushing concrete
- Spade. for piercing holes in concrete structures
- Shovel. used for drilling channels in the walls, which is carried out for the purpose of subsequent laying of communications
- Crown. a device that allows you to drill a hole of large diameter in the wall
- Mixers or whiskers. for mixing and stirring dry and loose materials
- Dust collectors. special devices that make drilling work dust-free
- Paint strippers. special types of nozzles for removing paint from concrete surfaces
- Break-through drill. a special kind of drill, which are used to make through holes in concrete and reinforced concrete structures
- Drills. for drilling holes in concrete and wood
- Vibrator. a device used to compress concrete in floors, walls, and other structures
- For hammering nails. also the peorator can be used as a hammer. For this purpose, a special device is installed in the tool chuck, which allows you to hammer nails into wood materials
- Pit drill. an attachment, which is designed to drill holes not in concrete, but in the ground. When operating such a device, only high-powered power tools are used
Knowing what attachments there are for the torch, it is necessary to pay attention to their consideration. Of course, the most popular are drills, which are used to drill holes in concrete, reinforced concrete and other similar materials. For this auger is chosen with an appropriate diameter, which depends on the technological task. Even if the tool is delivered with a concrete auger, you still need to buy them, because they are subject to wear and tear.
What kind of tool is needed for removing paint from walls?
After the invention of the peorator, the functionality of this power tool is expanding every year. It is possible to expand the functionality by producing different types of nozzles that can not only drill, but also chisel, punch, destroy, drill, mix, chisel, hammer, etc.п. All of these manipulations are carried out with the help of special devices. There are such types of nozzles on the peorator:
- Drills. for drilling holes in concrete and other similar materials
- Chisels are special devices, designed for removal of tiles and concrete crushing
- Picka. for piercing holes in concrete structures
- Shovel. is used for slotting channels in walls, which is performed in order to lay utilities
- A crown is a device that allows you to drill a hole of large diameter in the wall
- Mixers or whisk attachments. for mixing and kneading dry and granular materials
- Dust collectors. special devices that ensure dust-free drilling
- Paint strippers. special types of nozzles that allow you to remove paint from concrete surfaces
- Break-through drill. a special kind of drill that is used to make through holes in concrete and reinforced concrete structures
- Drill bits. for drilling holes in concrete and wood
- Vibrator. a device by means of which compaction of concrete mortar is performed when pouring floors, walls and other structures
- For hammering nails. a peorator can also be used as a hammer. For this purpose, a special device is installed in the tool chuck, which allows nailing into wood materials
- Pit drill. an attachment that is designed to drill holes not in concrete, but in the ground. When operating such a device, only high-powered power tools are used
Knowing what attachments there are for a feorator, it is necessary to pay attention to their consideration. Of course, the most popular are drills, which drill holes in concrete, reinforced concrete and other similar materials. For this auger is chosen with an appropriate diameter, which depends on the technological problem. Even if the bundle is attached to the grinder drill for concrete, then they still need to buy more, because they tend to wear out.
Brush on angle grinder for paint removal
Some home masters, in the repair in the apartment face the problem of cleaning the walls from old paint. I want to share with you the experience. Tried the various methods available, and similarly tell you about the alternatives.
What will be needed, the first thing that was tried in this case, it was a technical hair dryer. I have an inexpensive hair dryer firm Makita model HG5012K 230V. Industrial hairdryers differ in most respects by heating level.
This is what a technical hair dryer looks like. very similar to the normal one used to dry your hair, but don’t do it
Types of shanks on the attachments of peorators
Before sorting out the types of attachments for the peorator, it is necessary to clarify what types of shanks are used in such devices. So, peorators are divided into three main types according to their functional purpose:
- Household devices. an inexpensive type of percussion power tool, designed for infrequent use in the household. SDS plus type chucks are used in the construction of such tools
- Semi-professional. gimbals, which are designed for frequent use, for example, during construction and repair works. Depending on power, semi-professional models can be equipped with two types of chucks SDS plus and SDS max
- Professional devices. are used exclusively for work. They have only two modes. drilling with impact and chipping hammer, and SDS max chucks are used as an actuator
Read also: Pyrolysis tire recycling
Depending on the types of chucks, tools with corresponding types of shanks are used. Not only do they differ from each other, but also from drill bits and screwdrivers. What are the differences, and what parameters have different types of tails on the nozzles for the perorator, we will find out further.
- SDS-plus. type of shank, which is characterized by features such as length, thickness and shape. The length of sds plus type shanks is 4 cm or 40 mm, thickness. 10 mm, and it should be noted that they have 4 slots. Two open grooves and two closed grooves
- SDS max. the shanks on the shank for professional type peorators. They differ from sds plus in such parameters as length. 90 mm, thickness. 18 mm, as well as the number of slots. Besides the shape of these slots is larger than that of sds, they have two closed and three open types. This design ensures better engagement of the bit with the working mechanisms of the chuck
- SDS-top is an old type of shank, which has 14 mm diameter and 70 mm length. It is something in between sds-plus and sds-max. Today they are extremely rare and produced only for highly specialized models of torches
- SDS-quick. shank, which has a cylindrical shape with 4 parallel protrusions. Such bits can be used not only in the chucks of Bosch brand special rotary tools but also in the chucks of drills and screwdrivers
Today Chinese developers also produced a special design of shanks called Spline or spline. They have a cylindrical part with splines that resemble a gear. Such fixtures are used on Chinese-made peorators, which are equipped with special types of chucks.
Dismantled with the types of shanks for the bits under the perforators, it is necessary to understand the features of these devices, their capabilities and purpose.
The nozzle on the plaster removal peoratora
Peorator is a versatile tool that uses the attachments not only for laying utilities, but also for removing dust from the workplace, for stirring mortar, for compaction of concrete, removal of old paint, plaster, old tiles.
If you want to be that would choose the right tool for you, you need to know the approximate amount of work that will be performed. If the work is done occasionally, not a full day of work, but say, 3. 4 hours during the day, with breaks not in bad conditions, then a domestic peorator will be fully sufficient. If you need to perform a huge amount of work, the work is performed actually a shift, 5-6 hours, with short breaks, with heavy-duty operation criteria, then choose the professional tool.
These two groups of models differ in the following features: in weight, prof peoratorov much heavier, performance, the difference in power is not in the impact. The difference is not the design features but the number of devices. For this reason there will be a difference not in cost. Professional peorators are more expensive.
It is also necessary to compare the types of drives based on the percussion axis. Naturally, the horizontal types or straight not vertical.
The first types are used than simple domestic models, they are more comfortable to use, the narrow body allows you to work in small openings.
It is also necessary to know in what criteria the work will be done. If there is no access to the electronic network, then you have to choose the cordless peorator, it is more expensive than the network, but choose the one that will be more convenient. Choosing a cord type, you must pay attention to the length of the cord. Also, we should choose the number of operating modes. for household needs we take a three-mode, it is more universal and does not operate in 3 modes: drilling, drilling, impact (as a jackhammer). It is easier to pick up different additional attachments.
It is necessary to underline that the power is not the same indicator. Hole size and other related characteristics depend on power. The weight of the tool is also principal aspect of choice. It has an impact on how often you have to take breaks. Household tool weighs 3 to 5 kg.
Now about the impact force. Similar to oil is measured in Joules, for residential does not exceed 5 Joules. It is approximately, if to take a 5 kg weight and not drop it on the floor. You, the tool is enough for home work. An ordinary workable peorator must have 1200-1500 rpm not 4000-4500 strokes per minute.
READ How to Choose a Peorator for Home Work
Manufacturer of the tool
The main question, what company to choose the tool. That, in the market criteria a lot of different tools. Who offers their own, vary. Some recommend supporting the Russian manufacturer, others recommend taking a single, but reliable tool, others recommend China, it happens that no luck.
And, first of all, I’d like to note that more effective peoratorom always been listed from the company BOSH, which has not invented it as early as 1891, in 1931, released the first electronic percussion peorator. Very good is considered Makita, it is light, but very hardworking, like a real Japanese. It is not the size of the holes, but their number. Excellent reviews of Hitachi, especially the pro models, Hyundai. PRACTICE is just for one repair. Of course fall on a solid China, but there as luck, lottery.
Choose the model should be the manufacturer, whose service center is not very far away, who gives the best guarantee. It means that the manufacturer cares about quality. After all, this tool needs constant care not preventive maintenance, so that not to spend over time on an expensive repair.
Choice of nozzles
Not counting those operations that are listed in the annotation on the application, directly speaking drilling, chiseling, not strobing, using peoratora can perform various repair work is not preparing for him. Nettle, a vacuum cleaner attachment for peoratora very vivid, because removing dust during the work is very easy. The introduction of household vacuum cleaners leads to breakdowns due to the narrow dust, building vacuum cleaner to take is not cheap, but to find a rental. Dust extraction nozzle for peorator.
The nozzle on the drill for removing paint, with their own hands.
will need: a bolt M10 with a pre-cut cap, three nuts and two
Repair in a khrushchevka / Removal of old paint from the walls
old paint from the walls, in the presence ofpeoratora. not such a problem! I simply welded a metal
Yes, and separately, there are a lot of them presented in stores that sell tools. Nettles, many models from Bosch.
Paint remover attachment for the paint remover
When you remove old paint or plaster is much harder than thought. There are a lot of methods to do this. Particularly difficult if the paint is oil-based. Non-chemical methods not thermal. The paint-removing method with the feather duster is considered more productive. There are 3 kinds of nozzles used for this, each has its own advantages and disadvantages. It is a special chain put on a rod. The rod is inserted into the chuck, then the drill goes along the surface of the wall and the chains, hitting the wall, break the paint on it.
READ How to Cut the Corner of a Ceiling
The chain nozzle for removing old paint
You can also use the nozzle on the paint peorator for removing paint in the form of a brush, but such a nozzle is better for removing old acrylic paints. For removing oil-based paints, you need to take one with a shorter pile.
Nozzle. mop nozzle for removing old paint and plaster
Experts recommend and you can watch a video on the internet, how to remove paint from walls very effectively with a peorator and an attachment such as a chisel or spatula. But you have to move the torch a little sideways and sideways. If you get the hang of it, the cleaning process goes very quickly.
Nozzles on the peorator for removing plaster
When repairing very often there is a question of removing old plaster. The causes can be different: and the destruction of the old layer from time, or not qualitatively made work. But you have to remove.
There are many ways to remove. This can be done manually with a manual chisel and hammer, with a roughening machine or with a suitable bit on the rotary tool. With any method, it is imperative to protect the ingress of dust into the lungs and use personal protective equipment.
Types of shanks on the attachments of the peorator
Before we deal with the types of nozzles on the peorator, we need to find out what types of shanks are used on such devices. So, peoratorov are divided into three main types according to their functional purpose:
- Household devices. an inexpensive type of percussion power tool, designed for infrequent use in the household. SDS plus type chucks are used in the design of such tools
- Semi-professional. peorators, which are designed for frequent use, for example, in construction and repair work. Depending on the power, semi-professional models can be equipped with two types of chucks SDS plus and SDS max
- Professional devices. are used exclusively for work. They have only two modes. drilling with impact and chipping hammer, and SDS max chucks are used as a driving tool
Read also: Pressure bracelet with magnet
Depending on the type of chuck, tools with corresponding types of shank are used. They differ not only from each other, but also from drill bits and screwdrivers. What are the differences and parameters of different types of tailpieces for rotary tool bits we will clarify further below.
- SDS-plus is a type of shank, which is characterized by features such as length, thickness and shape. The length of sds plus type shanks is 4 cm or 40 mm, thickness is 10 mm, and in terms of shape it should be noted that they have 4 slots. Two grooves of open type, and two of closed type
- SDS max. shanks of sds max type for professional type rotors. They differ from sds plus in such parameters as length. 90 mm, thickness. 18 mm, and the number of grooves. Besides the fact that these slots are bigger in shape than sds, they also have two closed and three open types. Such design provides better meshing of the nozzle with the working mechanisms of the chuck
- SDS-top. this is an obsolete type of shank with 14 mm diameter and 70 mm length. It is a cross between sds-plus and sds-max. SDS-quick. are extremely rare today and available only for highly specialized models of torches
- SDS-quick. shank, which has a cylindrical shape with 4 parallel jaws. Such nozzles can be used not only in chucks of special Bosch brand peorators, but also in chucks of drills and screwdrivers
Today, also Chinese developers have made a special design of shank called Spline or Spline. They have a cylindrical part with splines, which resemble a gear. Such devices are used in Chinese-made rotary drilling machines, which are completed with special types of chucks.
After dwelling on the types of shanks for the bits for peorator, we need to understand the features of these tools, their capabilities and the purpose of their use.
Drills for Peorators
One of the most common types of attachments on peorators is a drill. It looks like an ordinary concrete drill bit for a drill, only instead of a cylindrical base for fixation in a collet chuck, there is a special design of SDS-max or SDS-plus. Drills are designed to make holes in concrete and brick walls. They consist of the following parts:
- The shank is the part that recesses into the chuck of the peorator. Due to the special design of the shank, the bit has a backlash after installation, due to which an impact movement is ensured
- Working part is a spiral, which is designed to extract dust and concrete particles from the drilled hole. Spirals can be screw type, as well as spiral and inclined. If augers allow drilling deep holes, spiral ones are designed for making holes for dowel installation
- The tip is the cutting part, which also serves as a guide when performing the corresponding work. Tungsten carbide inserts are applied to the tip, which increases the wear resistance of drills, as well as extends their service life. Tips have not only a different number of facets, but also appropriate types of sharpening, which affects the quality and speed of drilling holes in concrete
Drills are available in different diameters from 12 mm to 60 mm, and they also have different length from 10-15 cm to 1 meter. Depending on the tasks to be carried out, it is necessary to choose the appropriate roller drills.
How to remove paint with a squeegee?
Mechanical paint stripping is the easiest and most technically advanced way to remove the old paint. You can use a wide variety of tools to remove paint. You can, for example, work with a paint scraper. A faster and more efficient way to remove paint is to use electrical equipment.
Features of mechanical cleaning
It is not always necessary to remove the old paint coat before applying the new one. Much depends on the characteristics of both the old and the new paint. If adhesion is ensured without removing the coating, there is no need to spend effort on mechanical processing of the material. The best adhesive qualities have water-based compositions, which can hold on almost any surface.
If the adhesion of the materials can not be secured, the removal of the old coating can not be avoided. You will also have to remove the old paint if you plan to level the surface, as leveling compounds do not practically hold on painted materials.
It is not very difficult to determine the type of old paint: just try to peel off a piece of it. Water-based paints peel off quite easily. Oil-based paint is more difficult to remove.
In terms of labor costs and the choice of suitable tools, it is very important to determine the material of which the base is made. For example, with sandy plaster paint removal is not a difficult task, but with concrete it is much harder to remove the coating.
Before you start removing paint, you must prepare the workplace. The nearby space will be heavily littered in the course of work, so do the following:
- Remove all furniture from the room;
- If any items are too large and cannot be taken out, we cover them with polyethylene;
- Cover the floor with polyethylene film, but do not just spread it over the surface, but attach it to the baseboards with tape.
- Wear a respirator, goggles, rubber gloves, and apron.
Mechanical cleaning can be done with two types of tools: manual and electric.
The best effect is achieved with a power tool, especially an angle grinder (sander) or an axe. Both tools can be equipped with several types of attachments, including:
Below we will tell in more detail about the peculiarities of the use of certain types of tools.
Most often the following types of tools are used to remove paint:
- The axe. With this well-sharpened device, notches are created on the paint coating. Then the resulting recesses are generously moistened with water, which penetrates into the coating, softens it. Swollen, peeling paint can easily be removed with the same axe.
- a hammer and chisel. The easiest but also the most time-consuming way to remove the old paintwork.
- Scraper. This handheld device is often used to remove paint. However, if you have several coats, or if you have a thick, old oil-based paint coat, a scraper will not help, and you have to use more advanced methods.
The use of electrical equipment significantly reduces labor costs and time for the work.
angle grinder (colloquial name. angle grinder) allows you to remove the paint coating through the use of special attachments. The nozzle is a brush with very stiff metal wires. In operating mode, the wheel angle grinder develops speed up to 10 thousand revolutions, which provides high-quality removal of paint coatings.
Tip:! Do not use an overly large head, because there is a risk of breakage of the angle grinder. It is also not safe to work with a large head. It is better to buy a small nozzle.
You can also opt for a grinding wheel with an emery pad. The abrasive is attached to the bit with special Velcro. The optimal grit size of sandpaper. 80, but not less than 40, as fine-grained sandpaper quickly rubs off. The abrasive allows you to remove paint even from concrete surfaces. But sanding with sandpaper can ignite the abrasive.
Please Note! When working with an angle grinder use of protective glasses is mandatory, as on the sides at high speed pieces of the removed paint material fly away.
This type of electrical equipment perfectly copes with the mechanical removal of stale or thick paint coatings, but has a very important in some situations. high noise.
The device is equipped with a special nozzle. a spatula, which allows you to beat off not only paint, but also a layer of plaster. And if you work carelessly, you can also damage the substrate. even silicate bricks or concrete. The productivity of the torch depends on the complexity of the area, but on average you can handle about a square meter, or one and a half hours.
To clean the surface of paint can be used an electric drill with an abrasive attached to it. Fasten sandpaper sheets with Velcro. But this method is not very effective.
Construction hair dryer
In this case, the operating principle is based on heating the coating, which breaks the adhesion and causes the paint to peel off. And you must remove the paint layer immediately (with a trowel or scraper), without waiting until it cools down, otherwise later it will be even harder to remove the paint.
Note! When working with a hair dryer you need to keep in mind the following circumstance: you need to know exactly where the wiring is located, so as not to heat such places.
Working with a hair dryer is a very time-consuming process. Yes, and a layer of stale putty so do not remove. Construction hair dryer. this is more of a solution for a small area, and on larger spaces it is better to work with a peorator or angle grinder.
How to clean the paint from the bathroom wall with your own hands
Ways to clean bathroom walls from paint, a practical guide. Analysis of the situation, methods, recommendations for the choice of tools, description of the technology of removing the paint coating.
The task of cleaning bathroom walls from paint is not as simple as it may seem at first glance. For those who are doing it for the first time, the wrong approach to this task turns the cleaning of the wall surface into an extremely time-consuming and inefficient process. Work on the dismantling, contrary to popular opinion, also requires certain skills, special training and considerable effort.
In domestic conditions, there are two ways to scrape paint from bathroom walls: chemical and mechanical. The chemical method is to use special construction flushes, which in sufficient quantity produced by both foreign and domestic manufacturers. Such washes do an excellent job on metal substrates, are good on wooden substrates, but show rather mediocre results on wall materials.
Widely spread in domestic conditions paint removers for removing paint from the walls of the bathroom have not received. However, do not completely “discount” this method of cleaning. He can help you in places with limited access, where the use of hand tools is difficult. The compound is applied to the surface with a brush. After a few minutes the paint will begin to change into a gelatinous state. To remove it, all you need is a simple spatula. You do not need to apply much force. If you are dealing with a wall that has been painted in several layers, the procedure will need to be repeated more than once.
Mechanical cleaning of walls. theory and practice
For mechanical cleaning of bathroom walls from paint use a manual primitive tool or an electric tool. Primitive hand tool makes sense to use when the condition of the paint coating is bad, which is expressed in the presence of bloats, cracks or its peeling. In this case, you will be helped:
- Scraper to remove decorative coatings;
- planer blade;
- Any improvised tool with a wide sharp edge.
Of the tools listed, the scraper is the least suitable, as it removes paint in a thin layer and quickly blunts. Scraper to remove decorative coatings you can easily buy in a construction store, it is inexpensive.
In addition to the condition of the paint coating, an important parameter when choosing a tool is the presence, thickness and condition of the putty under it. A layer of unpainted gypsum putty is relatively easy to peel off the wall, along with the paint. If, however, before painting the wall was well primed, and a layer of putty was impregnated with primer completely, then the effective use of primitive hand tools, most likely, will be impossible.
The worst case is when the paint is applied to a concrete base or a well-done cement-sand plaster, where the putty layer is minimal. It is very difficult to clean such a surface. In this case, you shouldn’t even think about using primitive tools. That’s a lot of effort with minimal results. Arm yourself with a power tool.
Remove paint with a drill
In order to remove a layer of paint from the wall you can use the following power tools:
In order to remove paint from the walls of the bathroom with a drill, you will need a device that was invented by folk craftsmen and entered into use relatively recently. This tool does not have an official name. It is a metal rod, at the end of which, at an equal angular distance, are fixed three chains of several links. The other end of the rod is fixed in the chuck of the drill.
Paint remover attachment for the drill bit
After installing the device and turning the drill on, you will unwind the chains, thus making the device operational. You will get something similar to a propeller, but with flexible blades. These “blades” are the working part of the tool. A series of hard and steady blows will chisel the paint off the wall. Minimum muscle effort and quite acceptable results. The device has been tested, found to be quite effective, and adopted by master builders.
Be careful! The chain links will fray during use. If you don’t remove the worn-out link in time, it will come off in the process. Protect your face at all times. Remove or protect anything that could break. You can’t remove a link from only one chain. The number of links on all chains must be the same, otherwise the balance will be broken and it will be impossible to work with the tool.
Remove paint with a drill from the wall with a guarantee
If you have the worst condition of the painted surface to remove the paint layer described above, the chain tool might not be effective. In this case you have to use another option. The large-diameter through-hole brick cutter is up to the task. It’s important to apply the right amount of force. The bit should peel off the top layer, but not deepen so that you can guide the drill along the surface.
Naturally the larger the diameter, the faster you can clean the wall surface. Because of the high rotational speed and the principle of the crown itself, be prepared for dust. Protect your eyes and respiratory system. This method is effective, fast enough and has a good end result.
Clean the walls with a feather duster
There are three ways to peel paint off a bathroom wall. In the most difficult situation you, as in the case of the drill, will help with a drill bit for brick or concrete. The principle is the same. If you do not have a crown, you can use the spatula, which is included in the standard set of the peorator.
Cleaning the wall with a peorator
Hold the cutter at right angles to the wall. Dose the effort and speed of the burst. The blows should be strong, but superficial, so that you can move the tool. Do not despair if at first you do not succeed. Here the main thing is to “catch a wave”, show persistence and very soon you will acquire the necessary skill. The peorator will easily break up a layer of fossilized putty or multiple layers of paint. This method is practiced by a large number of masters.
Cutters for a hardware manicure
Using the cutter for a hardware manicure allows you to perform several procedures that result in a neat and attractive appearance of the nails. When choosing a cutter, it is recommended to proceed from 2 peculiarities of the work:
- The purpose of the procedure (getting rid of keratinized skin cells, correcting the nail and cuticle, polishing the nail plate, and other).
- Your experience in working with the machine and cutters.
Let’s dwell a little on the second point. The fact that an inexperienced technician or one who is just beginning to work with cutters for hardware manicure, can injure the nail and the skin around it, choosing a “rough” cutter. It is better to start with the more “soft”, or even practice on silicone tips to understand at what angle to hold the tool, and give the hand to get used to. In the hands of an experienced craftsman, cutters of any abrasiveness, shape and diameter can easily cope with any work.
About what such tools are like, what they are designed for, and how to use them, we will tell you below.
Characteristics and use of angle bits on a drill
There are several kinds of removable attachments for various operations that can be categorized as angle drill bits. Some nozzles are designed to create holes in places where a tool with a regular drill will not reach. There are adjustable and stationary angle nozzles. In the second case, the device is rotated by 90° and locked in this position.
Angular attachments can also be used as limiters. In essence, this nozzle simultaneously performs two functions: it limits the depth of the hole being formed and provides the required drill position, resulting in an accurate angle.
Drill bits and guided angled attachments can be fixed or adjustable
In addition, you can find on sale electric screwdriver attachment to the drill. It has a more complex design than the conventional version. The screwing heads enable fasteners (screws) to be driven at different angles.
Important! The screwdriving bit can only be used with tool models with which it is possible to reduce the rotational speed.
Angle-type nozzles are usually sold as kits, which include tips of different diameters. This makes it possible to install screws and self-tapping screws of different sizes. In rare cases, there are detachable fixtures that allow you to turn an electric drill into a grinder with an angle design.
Other varieties of useful drill bits
There are many other narrowly focused attachments that cannot be categorized as general due to their specificity, but many of them can be useful in construction as well as in the home. For example, drill sharpening attachments will keep this type of accessory in proper condition.
Drill bits are some of the most indispensable accessories for the workshop
With a pump attachment on the drill, you can pump solutions and liquids from one place to another. These tools are used in combination with a very powerful drill. This type of nozzle comes in handy in a private or holiday home in case of an emergency.
Country homeowners can benefit from feather duster attachments. They are used to pluck wild and domestic fowl. No skin or meat is damaged.
All kinds of cutters will be a great addition to the home workshop. With their help, craftsmen can decorate products made of wood with embossed patterns, as well as create grooves and holes, get rid of some defects.
The list of commercially available removable nozzles for an electric drill does not end here. There are dozens of other devices, allowing to increase the functionality of this tool and add new features to it. Some of these attachments are DIY (do-it-yourself). In any case, it is always necessary to adhere to safety precautions and check the reliability of fixation of attachments.
Methods of removing paint from walls
There are 3 ways to remove paint from walls:
- The chemical method, which uses washes, gels and reagents for removal;
- The mechanical method. using manual and electric tools;
- Thermal method. with open fire.
Read also: Why do you need a choke in lamps
Before choosing the method of removing the paint coating, the painted surface is analyzed. To do this, take a sharpened knife (kitchen or painting knife) and with maximum force try to make deep scratches. If the knife does not penetrate beyond the first layer, then the case is severe, and you will need to experiment with all methods of removal.
Otherwise, the mechanical method will be sufficient.
Mechanical method of removal
The following tools will be needed to clean paint off walls:
- Painting knife;
- Spatula. 70 or 100 mm;
- Thread roller;
- Bricklayer’s Hammer;
- A chain nozzle on a drill to remove paint;
- Spray gun. 1-2 liters;
- Vacuum cleaner construction;
- Small angle grinder;
- Diamond sanding disc;
- Petal sanding disc;
- Sanding disc;
- Brush tapered flagellum on an angle grinder;
- The widest paddle for the peorator;
- Concrete crown on a peorator;
- Special attachment for scraping. buchard.
The situation, how to clean the wall from the paint, requires the right approach. Therefore, the removal begins with the easiest ways. Using a scraper, a knife and a spatula it is possible to remove the layers on bloated spots and cracks.
When the light spots are cleaned, proceed to remove paint using an angle grinder with attachments. Paint remover from walls reviews? Each nozzle is tested on small areas of the surface.
Then the most effective one is used to peel off the layers.
Cleaning the walls of old paint is a very dusty job, which is convenient for two people to do. One deals directly with the removal, and the second. the subsidiary work. To minimize dust, use a spray gun and water to wet the walls.
And for rapid deposition of dust, water is sprayed into the air. While working with an angle grinder you can use a vacuum cleaner, taking the dust directly from under the nozzle. Excluding winter time, the windows in the room should be open.
Paint removal by hand.the process is long
The above technique of removing paint from walls is well suited for not strong painted surfaces: plasterboard partitions and plastered walls. But how to clean, if the angle grinder can not cope? Then the process involves a torch. The only serious disadvantage of this tool, compared to an angle grinder is the impact force. When cleaning, the plaster layer will be damaged and additional leveling will be required later.
This is especially true for the bathroom and kitchen, which were repaired back in Soviet times.
Not every performer knows how to remove paint from bathroom walls. It is not uncommon for bathroom walls to be covered with layers of paint for decades. Therefore, in such situations, the enamel is removed with an axe or a peorator.
Tip: sharpen the wide blade for the gritter like a chisel and you can remove any paint that gets in your way.
The most difficult case is rightly considered a problem: how to remove paint from a concrete wall. First try to remove the enamel with an angle grinder with different attachments or a peorator with a spatula. If the effect is not enough, you can try using a bouchard. an attachment for peorator, which resembles a kitchen hammer for making chops. Advantage of bouchard: it removes any paint from concrete walls. Combination of colors of paint for walls and ceiling?
The disadvantage: together with the enamel is removed 3-5 mm of the wall surface.
The thermal method of removal
Use this method of paint removal only in well-ventilated rooms. To improve ventilation, you can use an artificial draught using 2 summer standing fans. One fan is placed at the window and directs the air, saturated with chemical odors, outside the room.
The second one is installed at the door to pump clean air into the room.
To protect the respiratory organs, you should use at least a good respirator, because the emitted soot and smoke are well and permanently deposited in the lungs of man. Eyes protected by goggles.
The tools required to remove paint thermally:
First, one person burns a small section of the surface of the wall with the paint and the second person, immediately after, scrapes it off with a scraper, spatula or chisel. In this way, the firing is carried out until the wall is completely clean.
The same procedure takes much longer with a hair dryer.
The disadvantage of this method is the impossibility of using the burner in residential apartment buildings, as the smell will cause a fair resentment of the neighbors.
Remember: the thermal method is more dangerous to health than the mechanical method because it is very toxic.
The chemical method
How to clean the walls from the paint, if the above methods do not help? This leaves the chemical method. In this method to remove the paint use special rinsers in liquid and gel form and solvents (such as white spirit or acetone).
Wear full protective clothing, gas mask, gloves, goggles, and a raincoat to handle chemicals. The room must be well ventilated.
Liquid remedies are applied to walls with a sprayer, and thick gel ones with rollers and brushes. Depending on the manufacturer’s instructions, wait a certain amount of time after application and try to remove the dissolved bloated enamel. Remedy for removing old oil paint from walls? Repeat the procedure until you are completely clean.
When the wall is clean, it should be treated with an acidic solution (water, citric acid or vinegar). Remember: take care of yourself and your health for your family and friends.
No danger for communications
Such a nozzle very carefully removes the paint layer and at the same time does not damage the various cables. Also the paint stripper is very environmentally friendly because it does not heat the paint, which means that there is no decomposition of polymers and no toxins.
This nozzle is also very often used in older homes, some built in the 60s.
Because, the paint in such houses is very toxic (it contains a lot of lead), it can not be heated, otherwise it is very harmful to health, as well as it can not be turned into dust.