Patriot benzotrimmer stalls when closing the damper. Huter gas mower adjustment of carburetor

Trimmer for grass stalls when opening an air damper

Suppose you don’t start a trimmer for grass. In this case, the first thing is to check whether the fuel is enough in the tank, as well as evaluate the quality of the fuel mixture. To refuel a motorized unit, it is necessary exclusively high.quality gasoline. It is recommended to use fuel, the brand of which is not lower than AI-95. Refueling a trimmer for grass with fuel of unknown origin, not bought at a gas station, is fraught with frequent failures in the work of the tool. This can cause a breakdown of the cylinder-piston system. Repair in this case often exceeds the cost of the device itself.

Why is a trimmer not starting for grass gasoline? Incorrect preparation of the fuel mixture may also lead to this, which consists of oil and gasoline. The proportions in which the specified components are connected are indicated by manufacturers in the guide for the operation of a trimmer for grass. Preparing the fuel mixture is extremely not recommended in large volumes, that is, for the future. Indeed, with prolonged savings, there is a loss of the determining properties of the substance. Therefore, if a trimmer for grass does not start, it is worth draining the old fuel and use freshly prepared fuel mixture.

STIHL trimmer stalls when pressing gas

If the inconsistent is associated with the carburetor node, then recognize it of course when the vibrations of the lawn mower appear. When a hose bursts or a cable stretches, a change of data data is made.

When a braid for grass stalls at large speeds, this is due to the following problems:

• clogging or clutching the valve placed on the gas tank lid;
• The carburetor was drained under the influence of vibrations that occur during the operation of the mechanism;
• tasks with the circulation of fuel consistency;
• atmospheric air
• The hose created to fuel fuel cracked or slightly connected.

The carburetor is regulated by focusing on the operational annotation to the trimmer. For the option, it is often enough to weaken the tightness of its body. If there are problematic issues with the circulation of the fuel consistency, then it can gradually enter the carburetor. After its production, the engine stalls at huge speeds.

At single speeds, all.fought trimmer stopping the grass are subsequent:

• reducing the speed of the gearbox when heating it, which is a consequence of the use of inappropriate fuel consistency;
• clogging of the throttle;

• air entering the system;
• insufficiently fuel to perform the work of the lawn mower.

If a carburetor is a problem place, then the technique will stop at the “cold” and with a “hot” launch.

The unit can stall immediately after starting, if the carburetor is resolved or incorrectly configured. this causes an uneven supply of fuel. The result will be that the device begins to vibrate clearly. To eliminate problems, the carburetor is reconfigured, acting by annotation to the mechanism.

The gasoline trimmer for grass stalls at idle

Often, when reducing the speed, the motor motorcycles stalls and does not support idle speed when re.starting. The main reasons for the occurrence of such a breakdown include pollution or the dumping of the carburetor, as well as clogging of the air filter.

Gasoline trimmer for grass stalls at idle

In case of violation of the optimal settings of the carburetor, it is necessary to clean it and repeated adjustment. You can cope with clogging the air filter of a trimmer for grass by placing it for several hours in a solution with a conventional domestic detergent. If independent cleaning has not helped to cope with the blockage, it is better to purchase a new filter element in accordance with the operating manual.

After the measures, the user will not encounter a situation for a long time when a trimmer for grass stalls in idle and functions only when gas supplies.

They brought a Chinese benzotrimmer for repairs (they said it turned in the back, we are undergoing to start like.

Apart from time to time, from time to time, gasoline trimmers for grass can stall due to the fact that the valve located in the gas tank cover just clogged or stick. To find out, try to use the braid by loosening the gas tank cover. If in this mode the device is working on a dull way, clean the valve.

over, the lawn mower can stall due to the disgusting receipt of fuel in the carburetor. Nevertheless, repair t.e. It works normally at low speeds. Why then the device starts up, ask you? The reason for this is that at first, the fuel gradually runs into the carburetor and is enough to work at high power. The lawn mower does not work at idle. But then it is produced and at huge turns the engine begins to stall. As for the carburetor, here the problem may also consist in the fact that its body is very pulled.

In addition to everything else, do not forget to check the fuel intake hose. The inconsistent may be that it holds weakly or in general cracked.

These are the main prerequisites why the lawn mower can stall.

Air filter

On the pages of the global network, you can find information that the chainsaw of the Stihl 180 can stall due to severe air filter pollution. I would like to refute this not absolutely true information, and say that the STIHL carburetor MS 180 is equipped with a compensator, which is designed and installed in order to make an air focus necessary for the usual operation of the Stihl 180 chainsaw, bypassing the dirty filter. Of course, the power with a clogged air filter will fall a little, but it will definitely not stall. Another capacity may fall due to the wear of the piston, here the repair of the piston chainsaw of the Stihl MS 180 will already be required.

Forbidbenzokos when clicking on gas: causes of their solution.Glumpnbenzokos (trimmer for grass):. Fighting.

• idle sensor failure;
• clogging of the throttle;
• work of the sensor of the position of the trissellain;
• Injector or carburetor pollution

The grounds for breakdown can be completely different, therefore, when eliminating them, it will be necessary to operate with all kinds of actions and techniques. If your shoulders are considerable driver’s experience, and you know the features of the car’s work as your five fingers, regardless of the model, then the elimination of this kind of malfunctions will not cause you any problems. And all because such breakdowns are not complex or serious. It follows that you can establish the operation of the car without outside help. Well, if the level of awareness or lack of free time will not give you the opportunity to eliminate all defects yourself, it is better to seek help from knowledgeable people who can save you from unpleasant moments in the shortest possible time.

The reasons

Trammers for grass are reliable and durable (of course, subject to proper care). Most often, malfunctions arise due to contamination of structural elements.

If the engine of your lawn mower does not start, does not gain momentum, does not reach the power you need or suddenly stalls, it may be a reason:

• low.quality fuel (fuel mixture), it can be in long.term storage or in non.compliance with the recipe for the preparation of the mixture;
• The grass was wound on the shaft of the fishing/knife head;
• clogging of the air filter/muffler;
• Balance of the carburetor.

Ways to eliminate problems

The first three reasons are quite simple to eliminate. If the matter is the mixture, it is necessary to pour old fuel from the tank, prepare a new emulsion from high.quality gasoline and engine oil (if your motor requires a mixture) and pour it into a fuel tank. If a trimmer for grass works on clean gasoline, it’s still easier.

In the second case, it is necessary to carefully release the details of the trimmer for grass from the wound grass.

If the filter is clogged, you can try to rinse it. If this procedure has not brought the effect, replace it with a new.

The last reason why the lawn mower does not work properly will require you a little more knowledge and skills.

In order to properly adjust the carburetor of the lawn mower, it is necessary to observe a certain procedure. First of all, carefully clean the air filter. The easiest way to rinse it (it is advisable to carry out the filter with water regularly after 9-10 hours of operation).

After that, in the diagram of your trimmer for grass, which is in the instructions for the operation of the device, find the adjustment screws. Usually there are three of them: the first is responsible for the supply of fuel, the second. for idle, but the third is designed to limit the number of maximum engine speeds.

Next, you should turn on the unit and wait for the engine to warm up.

Slowly twist the first adjusting screw (fuel mixture). Catch the moment when the motor begins to stall, and turn the screw in the opposite direction 45 degrees. If you did not have time and the motor stalled, the screw should be turned 90 degrees. Open the throttle and see how the speed is going. Next, you should slowly unscrew the screw (each turn. the same 45 degrees) until the moment when, with full gas, the motor begins to firmly issue maximum revolutions.

The second screw, as mentioned above, controls the engine speed at idle. Weakening it, you reduce the number of revolutions, tighten. increase. The screw must be adjusted so as to ensure confident operation of the motor at small speeds. Accelerate the engine for better starting a little. At the same time, make sure that before the movement of the knives/coil with the fishing line, the motor makes several dozen revolutions. With poor starting the engine, screw the screw slightly.

After you have adjusted the first two screws, test the operation of the device at the maximum engine speed. If necessary, you can limit it (maximum). this will serve as protecting the motor from “boiling”. To do this, you need to do the third screw. Unscrew the fixation nut until the moment when the control screw can be calmly turned. To increase the maximum speed, the screw must be loosened to reduce. on the contrary, tighten. Fix the screw position with a nut. Test the work of the motor again.

Spend the position of the screws regularly. a high level of vibration characteristic of benzocoses can cause their involuntary shift.

Remember that carburetor adjustment is not the final procedure. During operation, Motokos, most likely, you will have to mess with it more than once, because an unbalanced carburetor is both an increased fuel consumption and a quick failure of the candles, not to mention reducing the power and productivity of the device.

Main reasons

The following reasons are possible why the lawn mower or trimmer for grass stalls when trying to re.start and continue the interrupted work:

• malfunctions in the engine;
• refusal to supply gasoline and oil;
• damage to pipelines (capillaries, hoses, pipes);
• malfunctions in the ignition system.

General description of problems with a scythe or trimmer is not enough here. Clear and immediate repair, high.quality maintenance is impossible without specifying the identified cause.

With gazeaming

You click on gas. and the trimmer for the grass stops working, does not develop momentum. The following alleged reasons are possible:

• The tuning of the carburetor was lost, which appears with an increasing load on the drive itself. after its long downtime or when working in extreme conditions;
• The fuel valve is clogged with deposits;
• The carburetor cable is weakened and sag;
• Excessively stretched, possibly torn off the fuel supply hose;
• The check valve (sapun) clogged with deposits. fuel does not enter the tank with fuel.

Important! Problems in the carburetor itself give themselves out the vibration of the lawn mower.

With an increase in speed

If the lawn mower (or a trimmer for grass) has stalled when the engine speed is added, check the device according to the following signs:

• clogging or sticking a valve built into the gas tank cover;
• valve adjustment violation;
• A failure in the work of pistons and cylinders. from vibration during the work of a braid for grass or a trimmer for grass, random blows directly in the session of the mowing of grass;
• violation of the supply of fuel mixture;
• excess air pumping into the motor;
• cracking of the fuel intake hose, weakening its compounds.

When the fuel.heating mixture is served with the right portions to the engine in a timely manner. it burns the amount that has managed to enter from the moment of the last gallpling, and he stalls again.

When working idle

Having launched a trimmer for grass or a motorcycle at idle, you find that the device is starting up. but it swallows, after working, say, 5-10 minutes. The reasons here may be as follows:

• clogging, violation of carburetor adjustment;
• Initially incorrect configuration of the valve mechanism of the carburetor;
• air filter clogging;
• reducing the speed of the gearbox (if any). the incorrect ratio of the fuel mixture;
• clogging the throttle;
• penetration of excess air into the fuel system;
• The fuel ends in the tank (and oil in the tank, if the engine is four.stroke).

If there are problems directly with the carburetor, the machine will stop both after a cold start and after launch on the already worked engine.

Immediately after the start

The stalling of motorcycles or a trimmer for the grass immediately after the start is due to the following reasons:

• impressive of previously adjusted valves;
• Initially incorrect setting of the valve mechanism;
• clogging with fuel supply valve;
• the hose is worn or poorly attached.

Due to the violated fuel injection algorithm, a lawn mower or a trimmer for grass is greatly vibrated in work.

In the process of warming the engine

If the engine heats up too fast, overheating. a lawn mower or a trimmer for grass works unevenly, as if jerking. After which she stalls. The reason may be as follows:

• boiling gasoline;
• The ignition wire was damaged (poor insulation);
• The coil in the ignition system has noticeably burned out, inter.seal circuits appeared.

The same heating is observed when using rotary (not disk) damper.

When opening an air damper

A lawn mower or a trimmer for grass stalls when raising the damper for the following reasons:

Ways to eliminate breakdowns

The following works are possible by carburetor:

• cleaning and adjustment of the fuel supply valve;
• similar work with a valve producing spent gases and pairs (after fuel burning);
• replacement of the spring weaker on the entrance valve;
• restoration of the tension of the carburetor cable;
• replacement of the fuel leaks hose, verification and strengthening of a weakened connection;
• changing the rotor damper disk;.
• Change of faulty wire or ignition coil.

The list of work on the work may also include the cleaning of the nozzles (in a 4-stroke engine), replacement of the valve washer, gaskets in tanks and so on.

The trimmer for grass stalls. how to eliminate the problem

A gasoline trimmer for grass is a useful tool for cleaning from unnecessary grass of house territories and large area lawns. The design of this technique is quite complicated, therefore, if the device breaks, there may be several reasons. The most likely factors that have caught a breakdown are usually described in the user guide. Knowing why a trimmer for grass stalls, you can try to independently eliminate the defect. The most common malfunctions provoking the motorcycle stops, and the ability to repair them with your own hands is in the material further.

In order to most accurately determine the cause of the trimmer malfunction for grass of any brand (for example, echo) and find out the possibility of eliminating it, you need to install, when performing what action the device stalls. The engine can turn off both at idle and at high speeds, heated under load or immediately after starting and t.D.

If you stalled after gas supply

Owners of gasoline braids often mention that the lawn mower stalls when you press the gas. Usually such a breakdown occurs due to problems in the carburetor. A failure in his work can occur due to long-term storage, use in difficult conditions, significant overload of the motor. The symptom of such a breakdown will be vibrating movements of the device during operation.

On a note! Users familiar with the repair of a car carburetor can try to restore this important node of the trimmer for the grass on their own, using the instructions for operating. Otherwise, the correct decision will be to seek help from the service center representatives.

Sometimes a trimmer for grass stalls when you give gas because the fuel valve is clogged. This interferes with the supply of gasoline. To eliminate the problem, it is enough to loosen the valve. Thus, normal supply of carburetor fuel will be restored.

Another possible reason why the lawn mower stalls when gas is supplied is pollution of the soundtress (check valve). This detail prevents the appearance of a vacuum in a gas tank. If it is clogged, the air does not flow, which means that fuel does not go to the carburetor. To eliminate the problem, it is necessary to clean this element.

If it stalled at high speeds

If the carburetor stalls at high speeds, this means that in idle and small there are enough incoming fuel, and to work on high is not enough. Then it is necessary to check the serviceability of the following nodes of the trimmer for the grass.

• Fuel hose. its integrity could be violated as a result of cracking. In this case, you need to replace the part. Or maybe you just need to tighten the clamps.
• A filter network between a carburetor and a hose for supplying a gasoline mixture-it could clog. In this situation, it is necessary to clean the detail.
• The valve on the gas tank cover. he could stick or clog with garbage. Cleaning is also necessary.
• Carburetor. perhaps as a result of constant vibration, it was resolved. This is usually characteristic of cheap Chinese details. To eliminate the problem, it is necessary to set up according to the instructions. In some cases, it is enough to only weaken the tightening of the carburetor case. If the adjustment is not possible, it is necessary to install a new element.
• Additionally, check the air filter. Perhaps it will need to be washed and cleaned or replaced with a new one, as he could clog with dirt and particles of grass when tilted technology, when the user mowed in hard.to.reach places.

If you stalled during work idle

If the lawn mower stalls, working idle, there may be several factors reasons.

• First you need to check the prepared fuel solution, when it comes to a four-stroke trimmer working on a gasoline-oil mixture. There is a chance that it is made incorrectly. the proportions are not withstanded. Because of this, the gearbox is warming up, and the revolutions on the drum are lowering.
• Another probable cause is blockage of elements such as a throttle, air filter or carburetor. You need to clean the indicated details.
• Another possible factor is to resolve or incorrectly carried out carburetor adjustment. You need to adjust the setting according to the instructions.
• Observe this problem mono and when opening the air damper. In this situation, the lack of fuel for a trimmer for grass occurs through the fault of the air flow.

If the device does not have enough fuel, it works properly at high speeds or when they increase, but stalls at idle. If the root of the problem consists in the carburetor, the lawn mower will be disconnected both with cold startup and hot.

If you stalled after starting

If the technique starts and stalls immediately after starting, this indicates the wrong settings or deducting the device. As a result of this, the fuel enters the engine unevenly, which leads to significant vibration and disconnecting the trimmer for the grass. To fix the breakdown, it is necessary to reconfigure the device according to the user management.

Another probable problem is the blockage of the valve supplying the gasoline mixture. It must be cleaned.

On a note! If the trimmer for the grass starts, but immediately stalls, it may also mean that the fuel is moving to the carburetor with difficulty. Weakening the valve will help to eliminate the problem. this will provide uniform and free circulation of fuel in the device.

Another possible reason is the damaged fuel intake hose. Air can penetrate through cracks and holes into the system. To solve the problem, you need to increase the engine speed in order to get rid of air bubbles that have penetrated the device.

If you stalled when opening the damper

If the technique works properly at idle, but stalls when opening an air damper, this reports about the penetration of air into the system through cracks in the fuel supply hose or damaged oil seals. To fix the breakdown and establish the work of the tool without driving air from the atmosphere, it is necessary to replace damaged parts.

Preventive measures and operating rules

So that the lawn mower does not work and does not stall when starting, it must be correctly stored and operated. Compliance with the following simple recommendations will forget about problems.

• When begging the grass, you need to monitor the state of the cooling system. It is also necessary to regularly clean the channels in the case and starter’s ribs.
• To clean the tool, you should use kerosene, solvent, or other washing tools.
• You can not clean a hot tool. it must cool before washing.
• It is important to observe the recommended working mode. this will avoid overheating of the engine.
• If a braid for grass is not used over the next thirty days, the fuel must be drained, otherwise it will fall into heavy components that can score the channels of the carburetor.
• After the fuel is merged, the trimmer for the grass should work at idle for some time until it turns off. This will allow you to completely get rid of the rest inside the working mixture.

To store the tool in cold weather, you need:

• completely drain the fuel;
• disassemble the lawn mower, wash and clean all available components;

• inspect the condition of the parts, eliminate all defects that can be corrected;
• pour the required amount of oil into the gearbox;
• Clean the air filter;
• perform partial disassembly of the engine, wash all moving parts, blow and lubricate thoroughly;
• To lubricate the piston, unscrew the candle, then raise the piston to the upper dead point by the starter, pour a small amount of oil into the hole for the candle and do the crankshaft several times.

Important! If there is no way to store a trimmer for grass in a warm dry room, you must first wrap the motor with an embarrassed rag.

Only by observing these rules, you can be sure that the lawn mower will work properly and will not stall for a number of seasons.

As you can see, stopping the work of a trimmer for grass can be caused by many reasons. Most of them can be fixed independently using the user instructions. In cases where there is no self.confidence, the equipment is recommended to be attributed to repairs. It is worth remembering that incorrect actions can cause even greater harm to the trimmer. As a result, the repair of Motokos will cost a much larger amount than it would be initially, and in the worst case, it may be necessary to buy a new unit.

Check the fuel pump relay

often there is a breakdown of a tanosa relay. To check it, you need to turn the ignition lock on a broken engine. A click should be heard in the relay area, and the operation of the gasoline pump will begin within a few seconds. If there is a click, but the pump does not work, perhaps contacts are burned in the relay. This can be checked by an oh.energized relay and after supply to its voltage winding 12 V with the battery terminals. Obstrated contacts should show infinity, and closed. resistance in a fraction of OM. If the relay is regular, you need to check the connection of the mass to the gasoline pump.

The reason why your tool abruptly stops working, namely the engine does not gain revolutions, breaks them off, or “stalls” in popularity, there may be more than one. Often this is to blame not only the engine itself, but also the adjacent systems, unit nodes, completely different details related to the preparation of the fuel-air mixture, its quality, transportation to the tool of the tool. Consider the most typical situations:

• He is not gaining momentum. The engine drive mechanics may be damaged or there were problems with the carburetor, but the main reason should be considered clogging of the air filter. To change the situation, it must be removed, cleaned, and if it is no longer subject to the latter, then change for a new one, promptly making an order on our website. Also, there will not be a turn of the braid for grass, if the cable from the carburetor constantly flies. disassemble the unit and firmly fix it, or buy a new one if cracks are found on the element, other types of deformations.
• At high speeds. The lid on the gas tank is clogged. it needs to be cleaned or new. often the reason is a sipped carb. We submit information on the correct adjustment of all screws in information articles. Check the quality of the fuel hose and change it to a new one if necessary.
• When heated. It occurs in moments when the fuel in the carburetor literally boils. It can also appear in the options if the carba damper is more rare, rotary type (not disk). The only option would be to replace the carburetor with a new. There is another option for a broken wire or ignition coil. In this case, change the element of the latter.
• Starts and stalls (immediately after launch). Solved or incorrectly adjusted carburetor is the main reason for this situation. Calm vibration will indicate an uneven supply of fuel, and competent adjustment of the node will help to correct the situation.

We hope you found the right answer to the question: why the lawn mower stalls, and all the proposed catalog details today, as always, are at your service. You need a piston trimmer for grass, a new carburetor, or the elements accompanying the operation of these systems. you will find everything in the open spaces of the Benzo SIP store.

This is interesting: how to choose a jacuzzi for the street?

Features of diagnosis

A well.posed question is already half the answer.The fact that the gasoline trimmer for the grass or the lawn mower stalls, namely, will significantly accelerate the search for a solution

• immediately after the start;
• when it works for some time idle. after one or several minutes;
• when pressing the gas button (or handle). or shortly after the start of work at high, submasymal speeds;
• under an enhanced load (for example, to cut the bushes, mow thick and high weeds);
• when warming up in the cold, it heats out excessively (the lawn mower stalled around overheating);
• After the opening of the air damper.

Depending on which of the circumstances was clarified during the pre.diagram, the exclusion method is looking for a more specific reason for the malfunction of motorcycles or a trimmer for grass.

Immediately after the start

The stalling of motorcycles or a trimmer for the grass immediately is due to the following reasons:

• impressive of previously adjusted valves;
• Initially incorrect setting of the valve mechanism;
• clogging with fuel supply valve;
• the hose is worn or poorly attached.

Due to the violated fuel injection algorithm, a lawn mower or a trimmer for grass is greatly vibrated in work.

When opening an air damper

A lawn mower or a trimmer for the grass stalls for raising the damper for the following reasons:

• swinging excess air due to the cracked fuel suction hose;
• sealing oil seals;
• improper functioning of the fuel and air dispenser when mixing them.

Stop motokos in this case is immediately.

In the process of warming the engine

If the engine heats up too fast, overheating. a lawn mower or a trimmer for grass works unevenly, as if jerking. After which she stalls.The reason may be as follows:

• boiling gasoline;
• The ignition wire was damaged (poor insulation);
• The coil in the ignition system has noticeably burned out, inter.seal circuits appeared.

The same heating is observed when using rotary (not disk) damper.

When working idle

Having launched a trimmer for grass or a motorcycle at idle, you find that the device is starting up. but it swallows, after working, say, 5-10 minutes.The reasons here may be as follows:

• clogging, violation of carburetor adjustment;
• Initially incorrect configuration of the valve mechanism of the carburetor;
• air filter clogging;
• reducing the speed of the gearbox (if any). the incorrect ratio of the fuel mixture;
• clogging the throttle;
• penetration of excess air into the fuel system;
• The fuel ends in the tank (and oil in the tank, if the engine is four.stroke).

If there are problems directly with the carburetor, the machine will stop both after a cold start and after launch on the already worked engine.

At high speeds

When a braid for grass stalls at high speeds, this is due to the following problems:

• clogging or clutching a valve located on the gas tank lid;
• The carburetor was diluted under the influence of vibrations arising during the operation of the mechanism;
• problems with the circulation of the fuel mixture;
• atmospheric air
• The hose intended for fuel fuel cracked or slightly connected.

The carburetor is regulated by relying on the operational instruction to the trimmer. For configuration, it is often enough to weaken the tightening of its body. If there are problematic issues with the circulation of the fuel mixture, then it can gradually enter the carburetor. After its production, the engine stalls at high speeds.

Malfunctions leading to improper operation of the chainsaw

There are a number of malfunctions that must be taken into account in diagnosis, t. to. They can lead to the interruptions of the saw.

• Damage to the crankshaft bearings. With worn crankshaft bearings, the appearance of a beating on the main shaft is inevitable, where the flywheel is attached. In such a situation, it is impossible to adjust the gap between the flywheel and the ignition coil, which entails interruptions in sparking, and unstable work of the chainsaw.
• Pollution of the pulse channel. The pulse channel serves to ensure the operation of the fuel pump, respectively, its pollution leads to improper operation of the pump, which will make it impossible to operate the saw (it will be launched and immediately stall).
• Wear of the CPG. As a rule, with increased wear of CPH, a decrease in compression in the chainsaw engine is observed, which is necessarily affecting its ability to develop momentum.
• Fuel and air filters pollution.

Why and what to do if a trimmer stalls for grass

There are several reasons why the trimmer for grass stalls when the grass. Usually the problem is provoked:

• wear of engine elements. piston, bearings, crankcase;
• malfunctions with fuel supply. a carburetor can fail in the device, sometimes a malfunction causes a clogged filter;
• mechanical damage to hoses, tubes and cables;
• disobedience with the ignition chain.

Most often, under a load for one reason or another, an old trimmer for grass, which has long been in operation, stalls for a particular reason. But sometimes the owners of new gasoline devices face problems.

Why is a trimmer for grass stalling when pressing gas, increasing speed

If the trimmer for the grass stalls when you give gas, then the problem is usually a malfunction of the carburetor adjustment. The malfunction often occurs if the device was inaction for a long time, and then received a significant load. Sometimes the unit stalls immediately after increasing speed, if before that it was operated in difficult conditions with violation of the rules.

The following reasons are also leading to problems with the performance of the device:

With stretching or rupture of the fuel hose in the gasoline trimmer, the elements that have become unusable must be changed. If the reason is in the clogged valves and filters in the unit, they are quite simple to clean.

If the reason that the trimmer stalls for the grass is caused by problems with the carburetor, the problems are accompanied by vibrations

Another common problem is that the trimmer for grass stalls with increasing speed due. In this case, you need to find the instructions for the device and carry out the reconfiguration of the unit. Often it is enough to weaken the tightening of the carburetor body.

Why does a trimmer for grass stall at idle

Garden trimmer for grass often stalls even at idle. The reasons for the malfunction are usually simple. First of all, the improper adjustment of the carburetor affects performance. it leads to problems both at high speeds and in idle mode. Turning off the device can provoke clogging of an air filter or throttle.

Sometimes a trimmer for grass stalls if incorrect fuel is used for it. The gearbox for this reason overheats and reduces momentum.

If a malfunction occurs, it is necessary, first of all, to inspect the carburetor unit and perform mechanical repair or configuration. If the cause is of poor.quality fuel, you need to replace the mixture with a more suitable.

What to do if the trimmer for the grass starts and immediately stalls

If the trimmer for the grass does not gain momentum and stalls immediately after starting, the problem usually consists in improper tuning the carburetor. In this case, fuel in the system comes unevenly, the gasoline unit vibrates and cannot work normally. Repair consists in reconfiguring a carburetor unit according to the instructions from the manufacturer.

Engine stop causes fuel supply valve. The element must be carefully cleaned, and then installed back in place. If the lawn mower still stalls immediately after starting, perhaps the valve is too tight and it needs to be loosened. In this case, the fuel mixture will begin to circulate through the system freely, and problems with the performance of the unit will disappear.

In some cases, a gasoline trimmer for grass stalls due to the fact that the hose contains damage that pass the air. During the repair, you need to replace the fuel tube with a new.

Attention! If the damage in the hose is insignificant, it is allowed to simply add a revolution drive. This will allow you to drive out air bubbles from the fuel system.

What to do if the trimmer works and stalls for the grass

Owners of garden gasoline units are faced with the fact that a trimmer for grass stalls at large speeds after a short work. First, the device begins to function with jerks, and then gradually stops.

Typically, the reason is the overheating of the system. gasoline in the carburetor simply boils. A trimmer for grass can heat up if the ignition circuit coil or wire is damaged. There is no point in repairing worn details, they are simply changed to new working.

The use of a trimmer for the grass does not lead the use of not disk, but rotary damper in a carburetor

What to do if the trimmer for the grass overheats and stalls

If a hot trimmer stalls for grass, the situation is a great danger to the performance of the unit. Repair should be carried out immediately, otherwise the device will be completely unusable, and it will be more difficult to restore it.

Overheating of the unit usually cause the following reasons:

• The use of inalitions. pour fuel into the tank with precisely with such an octane number that is recommended by the manufacturer;
• a large amount of air in the system. for this reason, the enriched mixture releases an excess of heat;
• non.compliance with the proportions of oil and gasoline in the preparation of fuel;
• The thick layer of soot on the muffler. soot is a good heat.insulating material, the gasoline braid for the grass during operation is very hot and stalls;
• The displacement of the axis of the spit.headed head inside the bar. for this reason, the rotation slows down, and the load on the engine increases.

If the gasoline unit stalls, you need to carefully examine it and eliminate first of all possible deformations of the structure. Then it is necessary to study the fuel parameters. If they do not correspond to the recommended, gasoline is replaced with a more suitable. If unnecessary air gets into the system, it is necessary to independently or with the involvement of specialists to adjust the position of the carburetor damper.

Sometimes a gasoline trimmer for the grass overheats and stalls because there is too old fuel in the tank. Use a fresh mixture for the unit, which was stored no longer than two weeks.

Attention! A trimmer for grass will overheat if you use it for too long, or mow with a weak device hard thick grass.

How to avoid breakdowns

Many breakdowns of a gasoline trimmer for grass can really be eliminated if you remove the causes, but if possible, it is recommended to, in principle, avoid faults. Simple measures allow to maintain the unit in a working state:

• You need to use a trimmer for grass in accordance with the recommendations of the manufacturer. It is impossible to use a weak device for removing hard weeds on the site, it is also not recommended to use motorcycles in excess of the due time. The gasoline unit needs to be turned off regularly and allow it to cool down.
• During the operation of the device, it is necessary to monitor the state of the cooling system. To maintain performance, the channels in the case are regularly cleaned, like the starter’s ribs. The clogging of the system often becomes the reason that the unit stalls from overheating.
• After using the gasoline trimmer for the grass, too, you need to clean. In this case, the procedure is not carried out for a hot unit, at first it must completely cool. For cleaning, use solvents, kerosene and other products allowed for use by the manufacturer.
• Before cleaning, the motorcycles for storage must be drained from the tank, the remains of unused fuel. If this is not done, the gasoline mixture will fall into heavy components and will clog the channels of the carburetor, which will subsequently cause malfunctions. After draining the fuel, the device is launched at idle and waited for it to turn off.

With the onset of autumn, a gasoline trimmer for grass must be correctly removed for storage. First, the residues of the fuel mixture are drained from the device, and then the unit is disassembled, rinse and clean all removable components.

Before cleaning gasoline motorcycles for storage, you need to evaluate the condition of its parts, carry out the necessary repair and replacement of nodes. Air filter needs to be cleaned. The engine is partially disassembled, rinsed and blown by moving elements, and then applied a new grease. To maintain the piston part, the candle is unscrewed and the piston itself is lifted to the top point, and a little oil is poured into the opening opening and the crankshaft is twisted several times.

Store a gasoline trimmer for grass in winter is necessary in a warm room

Why stalls the chainsaw

If the chainsaws start and stall, the reasons can be different. An external inspection should be carried out before attempts to fix the tool.

If the saw stalled during operation, you should check the presence of a mixture of oil with gasoline in the tank. If the fuel mixture is over, the device will not work. In those situations where gasoline still remained, the quality of the tool should be evaluated until the moment of is turned off. The occurrence of extraneous sounds and the subsequent sharp stop should alert.

The formation of soot on electrodes can also cause difficulties in the operation of the tool. Carefully inspect the device, clean if necessary.

When pressing gas

In cases where the chainsaw stalls when you press the gas, you should check the silencer and the fuel filter. A possible cause of problem is a violation of the tightness of the fuel hoses. In some cases, the addition of revolutions helps.

Sometimes checking all the details does not give a result, the tool is suffocating, zooiling when gas is added. If the device stalls when a person presses gas, it is possible to supply fuel in insufficient amount for normal operation. This phenomenon occurs due to clogging of the carburetor or filter.

Damage can occur due to clogging with air filter dust. When you give gas, the device stops working. Do not eliminate the problem yourself, since each model has individual characteristics.

Calling may cause failure or lack of lubrication on the chain of the chainsaw. If the circuit is dry, the channels should be cleaned through which the oil is supplied to the device tire. If the oil proceeds, the presence of cracks, defects on the pipes is noted, you need to treat them with sealant.

Under load

In situations where the device stalls at load, the problem can be with a gas tank or filters. Check the quality of the fuel and change the filter.

Often the saw does not gain momentum due to the fact that the mixture flooded in the gas tank has a low octane number. There is not enough power, sufficient heating does not work, the chainsaw stalls under load.

Often, malfunctions of the component parts lead to the fact that the device stalls under load. You should check for the presence of a sucker hoses, seals, gaskets. If the details are faulty, you can try to fix them or replace them.

In cases where the chainsaw is started and immediately stalls, the fuel is not enough, the device does not heat up. Turn the device

It is important to use a suitable mixture. Different types of fuel are better suited for different models

It is necessary to familiarize yourself with the instructions, recommendations, reviews of people whose device works normally

It is necessary to familiarize yourself with the instructions, recommendations, reviews of people whose device works normally.

At idle

In those situations where the chainsaw stalls at idle speeds, it is necessary to examine the state of the muffler. If the part is polluted, the spent gases are poorly displayed, the engine cannot continue to work, stops.

The saw stalls idle and in cases where the carburetor is incorrectly configured. It is better for beginners to fix the repair to specialists, since there is a chance of incorrect setup, because of which the tool will not be able to work. Tachometer is required to adjust the carburetor.

At high speeds

If the device stalls at high speeds, pay attention to the state of gasoline and air filters, the serviceability of the fuel hoses

Polluted air filter can be washed under warm running water

It is important to thoroughly dry the part before installing it so that the water does not violate the serviceability of the tool

If the liquid stops flowing through the fuel hose, it clogged. You can clean the part or replace with a new.

In cases where the saw stalls at large speeds, but the liquid flows through the hose, and the air filter is clean and working, look for the cause of the breakdown in the fuel filter. Install a new one in its place or clean.

In some cases, the problem is hidden in a gasoline pump. With the wear of the component part, the fuel begins to flow through the walls. If this phenomenon is noted, a new pump should be installed.

When tilted

If the saw does not develop speed when tilted, turns off, stops working, you need to check the fuel level in the tank. If it is not too high, the device is not supplied in an inclined position is not supplied with a sufficient amount of fuel, since the fuel tube is above the mixture level.

The causes of the malfunction and their elimination

In order to most accurately determine the cause of the trimmer malfunction for grass of any brand (for example, echo) and find out the possibility of eliminating it, you need to install, when performing what action the device stalls. The engine can turn off both at idle and at high speeds, heated under load or immediately after starting and t.D.

If you stalled after starting

If the technique starts and stalls immediately after starting, this indicates the wrong settings or deducting the device. As a result of this, the fuel enters the engine unevenly, which leads to significant vibration and disconnecting the trimmer for the grass. To fix the breakdown, it is necessary to reconfigure the device according to the user management.

Another probable problem is the blockage of the valve supplying the gasoline mixture. It must be cleaned.

On a note! If the trimmer for the grass starts, but immediately stalls, it may also mean that the fuel is moving to the carburetor with difficulty. Weakening the valve will help to eliminate the problem. this will provide uniform and free circulation of fuel in the device.

Another possible reason is the damaged fuel intake hose. Air can penetrate through cracks and holes into the system. To solve the problem, you need to increase the engine speed in order to get rid of air bubbles that have penetrated the device.

If you stalled after gas supply

Owners of gasoline braids often mention that the lawn mower stalls when you press the gas. Usually such a breakdown occurs due to problems in the carburetor. A failure in his work can occur due to long-term storage, use in difficult conditions, significant overload of the motor. The symptom of such a breakdown will be vibrating movements of the device during operation.

On a note! Users familiar with the repair of a car carburetor can try to restore this important node of the trimmer for the grass on their own, using the instructions for operating. Otherwise, the correct decision will be to seek help from the service center representatives.

Sometimes a trimmer for grass stalls when you give gas because the fuel valve is clogged. This interferes with the supply of gasoline. To eliminate the problem, it is enough to loosen the valve. Thus, normal supply of carburetor fuel will be restored.

Another possible reason why the lawn mower stalls when gas is supplied is pollution of the soundtress (check valve). This detail prevents the appearance of a vacuum in a gas tank. If it is clogged, the air does not flow, which means that fuel does not go to the carburetor. To eliminate the problem, it is necessary to clean this element.

Why does a trimmer for grass stall when you press the gas?

As you can see, the reasons why the trimmer for grass can stall when pressing for gas, a lot

That is why it is important to monitor the state of your assistant, to check the condition of all systems of the mechanism in time

Before you understand why any of the instruments of a summer house or a professional working with a motorcycle (benzocosa) stalls-it is worth distinguishing between two main situations when it happens. First, this is when the tool does not start after you have made the purchase, and the second. being in operation. So, we will analyze both.

• After starting.The case stalls the case if the carburetor is incorrectly configured or it was swollen. Fuel is supplied unevenly, respectively, distinct vibrations occur.
• When heated. The situation when the mechanism starts and works, but gradually “chokes” and stalls on the go. when gasoline boils in the carburetor, or the damper in the carburetor is not disk, but rotary view. In such cases, it is better to replace the carburetor itself. There is an air leakage option. when a coil or wire is broken in the ignition.
• At high speeds. This also occurs from the rounding of the carburetor or clogging the lid on the gas tank. It is worth trying work with a slightly parted valve. Be sure to check the fuel intake hose. it can be a crackling or poorly attached to the base.
• He is not gaining momentum. As the main reason why the engine is not gaining momentum. an air filter clogged. It is possible to subside a cable in a carburetor, a breakdown of a carburetor and the occurrence of problems with the motor drive mechanics.

There are times when the detail of the mechanism requires mandatory replacement, so we are always happy to offer spare parts for the lawn mower

It is important to understand that sometimes saving on minor elements can lead to a breakdown of such global components as a carburetor or engine. Therefore, competent operation and timely replacement of the necessary particles will provide you with full work with pleasure

The gasoline trimmer for the grass starts and stalls

Why is a trimmer not starting for grass gasoline? Reasons and their elimination

Recently, a gasoline trimmer for grass has acquired the status of one of the main tools in the arsenal of summer residents. And this is not surprising, because a motorized braid for grass allows you to quickly put a personal plot in order. However, sometimes it happens that the trimmer for the grass does not start hot and even on cold. In such situations, you have to independently establish the cause of the malfunction. Let’s find out what to do if a trimmer does not start for grass. The reasons that most often lead to such troubles will be considered further.

Malfunctions of gasoline and diesel garden motoblocks

Garden Unoa Tractor is a very useful thing in the household. With a good walk.behind hand, work in personal plots goes much faster. But motoblocks, like other household equipment, sometimes break.

The most common malfunctions of garden motoblocks:

• The same.based tractor stalls at loads;
• The same.based tractor works with interruptions;
• The same.based tractor smokes, stalls, muffler makes unusual sounds;
• The same.based tractor does not start;
• The same.based tractor starts, but stalls quickly;
• The same.based tractor stalls when heated.

Malfunction: one.axic tractor stalls at loads

If the unoic tractor functions normally for several minutes, and then stalls, the reason usually lies in the fuel supply or in problems in the ignition system.

To find out what is the cause of the motoblock malfunction, you must first check how the fuel is supplied:

• Get a candle and inspect. if it is dry, then there is not enough fuel;
• check if the fuel is enough in the gas tank of the walk.behind tractor;
• Make sure that the fuel valve is open. the blocked faucet can be a simple reason that the same.based tractor stalls.

If the problem of the malfunction of the gasoline motoblock in the ignition system, it must be re.adjusted as follows:

• remove the cover that protects the ignition system;
• turn the moss engine of the engine until the contacts in Magneto;
• Using the probe, measure the distance from the anvil to the hammer;
• turn the moss to maximum compressing the piston;
• Once again, turn the moss before the appearance of a knock indicating the work of a overtaking coupling;
• Turn the moss in the other direction so that its label coincides with a mark on the body of the walk.behind tractor;
• set the distance from interrupting contact to a fist of 0.3 mm;
• fix the cam with a screw that is above the element;
• Install the lid in the body of the walk.behind tractor.

If the adjustment is made correctly, the unoic tractor will not stall during operation.

Malfunction: one.axle tractor works with jerks, with interruptions or at reduced power

If the unoic tractor on a gasoline or diesel engine begins to work with interruptions, you need to instantly turn off the unit and start eliminating the malfunction.

Continuing to work with a faulty walk.behind tract means to bring it to more serious breakdowns.

• If the engine of the gasoline walk.behind tract makes return movements, it is necessary to rinse the pump and hoses to supply fuel and replace the fuel with a better;
• When the unoic tractor works with jerks due to incomplete warming up the engine, you need to drown out the motor, let it cool completely, start and warm it up for ten minutes;
• If the engine power has fallen, you need to check and clean the filter system;
• If there is a wear of the ignition magnet, you need to replace the part with a new.

Malfunction: one.axic tractor smokes and stalls, the muffler makes unusual sounds

• With an excess of oil, drain the fuel, rinse the fuel pump and the hose system, pour new fuel;
• check the correctness of the gap between the electrodes;
• If it became obvious that the fuel does not completely burn, disassemble the piston system, rinse and dry the cylinder, correctly configure the carburetor.

Malfunction: one.axic tractor starts up, but stalls quickly

Such a malfunction happens if there are problems with contacts. What to do:

Malfunction: one.axic tractor stalls when heated

This problem arises due to excessive air entering the carburetor. With such a malfunction, the gas trigger should be squeezed out half. After the motor factory before the start of work, it is necessary to draw well.

If it is not possible to cope with the malfunctions of the garden motoblock, the unoic tractor stalls, the uniform tractor does not start, contact the Alfa-in motor blocks repair workshop using the high-quality repair of gasoline motor blocks using original components that will always be found in our warehouse.