Patriot gasolimmer stalls when adding gas.

5th April 2023

trimmer for grass gasoline sharply stalled and does not start

In order to most accurately determine the cause of the trimmer malfunction for grass of any brand (for example, echo) and find out the possibility of eliminating it, you need to install, when performing what action the device stalls. The engine can turn off both at idle and at high speeds, heated under load or immediately after starting and t.D.

If you stalled after starting

If the technique starts and stalls immediately after starting, this indicates the wrong settings or deducting the device. As a result of this, the fuel enters the engine unevenly, which leads to significant vibration and disconnecting the trimmer for the grass. To fix the breakdown, it is necessary to reconfigure the device according to the user management.

Another probable problem is the blockage of the valve supplying the gasoline mixture. It must be cleaned.

On a note! If the trimmer for the grass starts, but immediately stalls, it may also mean that the fuel is moving to the carburetor with difficulty. Weakening the valve will help to eliminate the problem. this will provide uniform and free circulation of fuel in the device.

Another possible reason is the damaged fuel intake hose. Air can penetrate through cracks and holes into the system. To solve the problem, you need to increase the engine speed in order to get rid of air bubbles that have penetrated the device.

If you stalled after gas supply

Owners of gasoline braids often mention that the lawn mower stalls when you press the gas. Usually such a breakdown occurs due to problems in the carburetor. A failure in his work can occur due to long-term storage, use in difficult conditions, significant overload of the motor. The symptom of such a breakdown will be vibrating movements of the device during operation.

On a note! Users familiar with the repair of a car carburetor can try to restore this important node of the trimmer for the grass on their own, using the instructions for operating. Otherwise, the correct decision will be to seek help from the service center representatives.

Sometimes a trimmer for grass stalls when you give gas because the fuel valve is clogged. This interferes with the supply of gasoline. To eliminate the problem, it is enough to loosen the valve. Thus, normal supply of carburetor fuel will be restored.

Another possible reason why the lawn mower stalls when gas is supplied is pollution of the soundtress (check valve). This detail prevents the appearance of a vacuum in a gas tank. If it is clogged, the air does not flow, which means that fuel does not go to the carburetor. To eliminate the problem, it is necessary to clean this element.

Why does a trimmer for grass stall when you press the gas?

As you can see, the reasons why the trimmer for grass can stall when pressing for gas, a lot

That is why it is important to monitor the state of your assistant, to check the condition of all systems of the mechanism in time

Before you understand why any of the instruments of a summer house or a professional working with a motorcycle (benzocosa) stalls-it is worth distinguishing between two main situations when it happens. First, this is when the tool does not start after you have made the purchase, and the second. being in operation. So, we will analyze both.

After starting.The case stalls the case if the carburetor is incorrectly configured or it was swollen. Fuel is supplied unevenly, respectively, distinct vibrations occur.
When heated. The situation when the mechanism starts and works, but gradually “chokes” and stalls on the go. when gasoline boils in the carburetor, or the damper in the carburetor is not disk, but rotary view. In such cases, it is better to replace the carburetor itself. There is an air leakage option. when a coil or wire is broken in the ignition.
At high speeds. This also occurs from the rounding of the carburetor or clogging the lid on the gas tank. It is worth trying work with a slightly parted valve. Be sure to check the fuel intake hose. it can be a crackling or poorly attached to the base.
He is not gaining momentum. As the main reason why the engine is not gaining momentum. an air filter clogged. It is possible to subside a cable in a carburetor, a breakdown of a carburetor and the occurrence of problems with the motor drive mechanics.

There are times when the detail of the mechanism requires mandatory replacement, so we are always happy to offer spare parts for the lawn mower

It is important to understand that sometimes saving on minor elements can lead to a breakdown of such global components as a carburetor or engine. Therefore, competent operation and timely replacement of the necessary particles will provide you with full work with pleasure

A gasoline trimmer for grass is not started. 10 possible reasons

Before trying without the help of others to do the work of the tool, closely study the management of its operation. Maybe the information contained in it will stumble you upon a particular idea. When working in the load, the trimmer for the grass stalled and no longer starts.There is a spark.Gasoline acts. In an unpleasant case, you will have to find the cause of the malfunction by selection. Why doesn’t the lawn mower start: floods the spark plug, after winter, under load and other reasons for the breakdown of a gasoline trimmer for grass. It may be one of the subsequent:

The switch on the bar has not been transferred to the “v.””. This is one of the simple actions, but from time to time the brand new are blurrying to turn on the tool before starting it.
Similar errors include the lack of fuel in the tank. If the fuel ends, and you forgot about it, just pour into the tank (usually placed near the motor) AI-92 gasoline.
Absence, inappropriate mixture or incorrect proportion of oil for engines. In the standard, less than 50 g of oil should often be added. I don’t remember a trimmer for Homelite grass, it is chasing and starts to start poorly in the time. This will serve as an additional lubricant and will support the engine of your trimmer for grass in working condition. Also consider that oil is of various types (“synthetics”, “semi-synthetics”, “mineral water”)-they all affect the operation of the mechanism differently.
If a trimmer mowel for grass does not start after winter, drain fuel remaining in the gas tank and change it to the freshest. This is especially burning for small low.power trimmers with malhangic engines sensitive to poor consistency. In addition, during the winter, a precipitate can form on a gas tank day, which is due to which the tasks with the operation of the device appear.
Excessive swing of fuel can also become one of the circumstances that the trimmer for the grass has not stalled and does not start. Когда воздушная заслонка перекрыта, свечу заливает топливом. It should be turned and dried, and then stick in your place and try to launch the engine, holding the gas trigger. STIHL 180 chainsaw is not started? Reasons and decision! To date, the manufacturer of STIHL has a leading place among other companies that arbitrarily. It is better to check it for the presence between the electrodes of the sparks before that. If there is no spark, the candle should be changed.
Conclusions with the filter. trimmer for grass but not suitable for my case. Starts and works does not gain momentum. That a trimmer for grass does not start hot and even cold. If the lawn mower is not started. If your trimmer for the grass starts poorly, remove the air filter and run the tool without it. If everything happens, the filter should be changed to a new. As an option-painfully cleaning and blowing the old one, but the substitution will still have to be done at some point.
trimmer for the grass stalled and does not start? Try to clean the so.called Sapun. an element designed to smooth out pressure in the gas tank. Cleaning can be done with an ordinary long needle. The clogged sapun often becomes a prerequisite for a malfunction.
Knives are removed from the car. some models will not work under this condition.
Violation of density. You can check this using a pressure gauge. If the pressure begins to fall, you should find which of the parts of the carburetor is faulty. In most cases, carburetor laying wears out.
From time to time after a long period of work, you can see that the trimmer for the grass has overshadowed and does not start. Benzo trimmer for STIHL FS45 grass starts up and tried to start. Or not starting, MTD STC 55 P. Author. VO-1, you need to know that you should definitely take breaks. The amount of continuous work recommended for this model should be indicated in the annotation. You bought yourself a new gasoline trimmer for grass and in this case the lawn mower will not start or. Also, an overheating failure can lie in a faulty ignition coil or in the air cooling system, which prevents overheating.

Why will the chainsaw be stalled and zapayed when the gas is pressed

Chainsaws are quite reliable and simple design. Therefore, if you properly take care of them and process them on the basis of the recommendations of the manufacturer, then they fail, very rarely and various kinds of breakdowns are quickly eliminated. But if you are faced with this situation and want to personally repair your tool, without turning to the professionals for help, then we will delve into the information provided below.

In fact, it is unambiguous and accurately impossible to determine the reason why the tool does not start or stops when pressing gas, since a lot of factors affect this. But do not forget that, starting with the fact that the chainsaws are equipped with a simple two.stroke engine, conditions such as lubrication, fuel, sparks and air are important for its effective operation.

Therefore, the carburetor directly participates in the preparation of the fuel-air mixture, the filter cleans the air of dust, the ignition unit and the spark plug create a spark, and there is a lubricant in gasoline.

That is why you should look for the reasons for this kind of failure in a sequential order, starting directly with simple and gradually moving on to complex. And this is an important factor in the correct repair, since a person who, without hesitation begins to analyze the carburetor, leads him to risk. Since this type of unit should be repaired or adjusted directly in special workshops (read about the regulation of the carburetor).

There is no spark and chainsaw does not gain momentum

The chainsaw stops when pressing the gas due to the fact that neither spark. This can happen when there is no good contact between the tip of the candle and the wire (high voltage). However, if this type of connection works correctly, but there is still no spark, then the whole reason. This is an incendiary block (electronic)

It is important to note that details of this type cannot be repaired, so they can only be replaced

Do not forget that by studying the spark plug, you can get significant information about the breakdown of the chainsaw. Since if its surface is dry, then the reason for this is a cylinder, which is not directly included in the fuel. That’s why you will have to step by step by step by step by the entire spectrum of his presentation. If the candle is covered with black carbon, this means that the carburetor does not work properly, that is, it either supplies a lot of fuel or pours oil directly into gasoline.

If you put the cable instead of the fishing line, not having the opportunity to let it go, securely fix the two ends of the cable and cut them off with welding (a drop of molten metal prevents cable unturation). Such a tool clogs grass at a time. Cuts shoots in a thickness thick. Not so afraid of stones as a disc. However, there is a problem: when wear, pieces of cable threads break off, and these twisted wires remain at the place of mowing. The offensive on them can lead to injuries.

But pieces of cable left on the field. This is half the trouble. The fishing line for the trimmer, breaking off, weakens the dynamic shocks of transmission and engine, the cable does not give such an opportunity. Result. Quick wear of the brush.

Why is a Chinese lawn mower not developing momentum?

The trimmer for grass is gaining momentum, a very common problem and of course not always a familiar solution.

Also, the ignition coil can be broken in electrical equipment. In this case, the brush does not start or does not start and works with interruptions, and then stops, or does not start at all when hot.

You can check the serviceability of the coil in the same way as when checking the spark: unscrew the candle, lean it against the trimmer body for the grass. If there is no spark when you press the starter, or it appears each other, you need to change the coil.

Continuous work of the shieldcorse is indicated in the instructions for the trimmer for the grass. On average, kosim for 15-20 minutes, after which we turn off the trimmer for the grass and let it cool for 3-5 minutes. Weather conditions also affect the duration of continuous work. In hot weather, during skewing of high grass, thickets of weeds, under a large load, a trimmer for the grass overheats faster.

Many brush problems arise due to incorrectly prepared fuel mixture. In two.stroke engines, the lubricant is carried out with special oil (not ordinary engine oil!) Mixed with gasoline. If the oil does not mix with gasoline, the brush will quickly fail. Mix oil / gasoline in the proportion indicated in the instructions for the trimmer for grass. This is usually 1:40 or 1:50.

The question often arises: the proportion of 1:50 is how much oil and gasoline?

We identify the cause of the malfunction

To repair the lawn mower yourself, it is best to be guided by the principle of “from simple to complex”. First, check if there is enough gasoline in the tank. If the mower stopped starting after wintering, it is worth draining the old fuel and replace it with a new. Sometimes low.quality gasoline comes across, which can give a precipitate or even delay in the winter, and some gas mowers are very sensitive to fuel quality.

If there is confidence as gasoline, but the lawn mower does not show signs of life, the next thing you need to do is check the spark. To do this, remove the wire with a cap from the candle and twist it with a special candle key, which should go with the lawn mower. Then throw the cap on the candle, attach its threaded part to the metal part of the engine and ask someone to pull the starter. At this moment, a bright blue spark should appear, which is clearly noticeable even during the day. Keep in mind that you need to lean the candle against the clean metal surface of the engine, which is not covered with paint and which can be current.

The trimmer for grass stalls. how to eliminate the problem

A gasoline trimmer for grass is a useful tool for cleaning from unnecessary grass of house territories and large area lawns. The design of this technique is quite complicated, therefore, if the device breaks, there may be several reasons. The most likely factors that have caught a breakdown are usually described in the user guide. Knowing why a trimmer for grass stalls, you can try to independently eliminate the defect. The most common malfunctions provoking the motorcycle stops, and the ability to repair them with your own hands is in the material further.

If you stalled after gas supply

Sometimes a trimmer for grass stalls when you give gas because the fuel valve is clogged. This interferes with the supply of gasoline. To eliminate the problem, it is enough to loosen the valve. Thus, normal supply of carburetor fuel will be restored.

Another possible reason why the lawn mower stalls when gas is supplied is pollution of the soundtress (check valve). This detail prevents the appearance of a vacuum in a gas tank. If it is clogged, the air does not flow, which means that fuel does not go to the carburetor. To eliminate the problem, it is necessary to clean this element.

If it stalled at high speeds

If the carburetor stalls at high speeds, this means that in idle and small there are enough incoming fuel, and to work on high is not enough. Then it is necessary to check the serviceability of the following nodes of the trimmer for the grass.

Fuel hose. its integrity could be violated as a result of cracking. In this case, you need to replace the part. Or maybe you just need to tighten the clamps.
A filter network between a carburetor and a hose for supplying a gasoline mixture-it could clog. In this situation, it is necessary to clean the detail.
The valve on the gas tank cover. he could stick or clog with garbage. Cleaning is also necessary.
Carburetor. perhaps as a result of constant vibration, it was resolved. This is usually characteristic of cheap Chinese details. To eliminate the problem, it is necessary to set up according to the instructions. In some cases, it is enough to only weaken the tightening of the carburetor case. If the adjustment is not possible, it is necessary to install a new element.
Additionally, check the air filter. Perhaps it will need to be washed and cleaned or replaced with a new one, as he could clog with dirt and particles of grass when tilted technology, when the user mowed in hard.to.reach places.

If you stalled during work idle

If the lawn mower stalls, working idle, there may be several factors reasons.

First you need to check the prepared fuel solution, when it comes to a four-stroke trimmer working on a gasoline-oil mixture. There is a chance that it is made incorrectly. the proportions are not withstanded. Because of this, the gearbox is warming up, and the revolutions on the drum are lowering.
Another probable cause is blockage of elements such as a throttle, air filter or carburetor. You need to clean the indicated details.
Another possible factor is to resolve or incorrectly carried out carburetor adjustment. You need to adjust the setting according to the instructions.
Observe this problem mono and when opening the air damper. In this situation, the lack of fuel for a trimmer for grass occurs through the fault of the air flow.

If the device does not have enough fuel, it works properly at high speeds or when they increase, but stalls at idle. If the root of the problem consists in the carburetor, the lawn mower will be disconnected both with cold startup and hot.

If you stalled after starting

If the technique starts and stalls immediately after starting, this indicates the wrong settings or deducting the device. As a result of this, the fuel enters the engine unevenly, which leads to significant vibration and disconnecting the trimmer for the grass. To fix the breakdown, it is necessary to reconfigure the device according to the user management.

Another probable problem is the blockage of the valve supplying the gasoline mixture. It must be cleaned.

On a note! If the trimmer for the grass starts, but immediately stalls, it may also mean that the fuel is moving to the carburetor with difficulty. Weakening the valve will help to eliminate the problem. this will provide uniform and free circulation of fuel in the device.

If you stalled when opening the damper

If the technique works properly at idle, but stalls when opening an air damper, this reports about the penetration of air into the system through cracks in the fuel supply hose or damaged oil seals. To fix the breakdown and establish the work of the tool without driving air from the atmosphere, it is necessary to replace damaged parts.

Preventive measures and operating rules

So that the lawn mower does not work and does not stall when starting, it must be correctly stored and operated. Compliance with the following simple recommendations will forget about problems.

When begging the grass, you need to monitor the state of the cooling system. It is also necessary to regularly clean the channels in the case and starter’s ribs.
To clean the tool, you should use kerosene, solvent, or other washing tools.
You can not clean a hot tool. it must cool before washing.
It is important to observe the recommended working mode. this will avoid overheating of the engine.
If a braid for grass is not used over the next thirty days, the fuel must be drained, otherwise it will fall into heavy components that can score the channels of the carburetor.
After the fuel is merged, the trimmer for the grass should work at idle for some time until it turns off. This will allow you to completely get rid of the rest inside the working mixture.

To store the tool in cold weather, you need:

completely drain the fuel;
disassemble the lawn mower, wash and clean all available components;

inspect the condition of the parts, eliminate all defects that can be corrected;
pour the required amount of oil into the gearbox;
Clean the air filter;
perform partial disassembly of the engine, wash all moving parts, blow and lubricate thoroughly;
To lubricate the piston, unscrew the candle, then raise the piston to the upper dead point by the starter, pour a small amount of oil into the hole for the candle and do the crankshaft several times.

Important! If there is no way to store a trimmer for grass in a warm dry room, you must first wrap the motor with an embarrassed rag.

Only by observing these rules, you can be sure that the lawn mower will work properly and will not stall for a number of seasons.

As you can see, stopping the work of a trimmer for grass can be caused by many reasons. Most of them can be fixed independently using the user instructions. In cases where there is no self.confidence, the equipment is recommended to be attributed to repairs. It is worth remembering that incorrect actions can cause even greater harm to the trimmer. As a result, the repair of Motokos will cost a much larger amount than it would be initially, and in the worst case, it may be necessary to buy a new unit.

The lawn mower stalls when you press the gas

The hole in the fuel cover (saepun) of a trimmer for grass

With a similar problem, it is worth paying attention to the fuel valve, which, when clogging, ceases to normally pass the fuel mixture. By solving this malfunction, it is weakening using a suitable tool. In addition, the problem with the circulation of the fuel mixture may cover in the contamination of the valve. To do this, just blow it with a stream of compressed air.

If you stalled when opening the damper

If the technique works properly at idle, but stalls when opening an air damper, this reports about the penetration of air into the system through cracks in the fuel supply hose or damaged oil seals. To fix the breakdown and establish the work of the tool without driving air from the atmosphere, it is necessary to replace damaged parts.

Another possible reason for the breakdown is the malfunction of the carburetor dosage system. To eliminate this problem, it is better to contact professionals.

Immediately after you started

The unit can stall immediately after the launch, if the carburetor is sipped or incorrectly configured. this causes an uneven supply of fuel. The result is that the device begins to vibrate clearly. To eliminate problems, the carburetor is reconfigured, acting according to the instructions for the mechanism.

The engine also stops when the valve supplies fuel clogs. In such cases, it is enough just to clean it. If the lawn mower at first earned, but then immediately stalled, then possible fuel to the carburetor unit enters some difficulty. The weakening of the valve helps to solve the issue, which provides free circulation of the mixture in the system.

The stop can also be caused by air leaks in the presence of mechanical damage to the hose (holes, cracks) that fuel fuel fuel. In this case, the drive should be added to the drive to quickly drive air bubbles from the system.

The gasoline trimmer for grass stalls at idle

Often, when reducing the speed, the motor motorcycles stalls and does not support idle speed when re.starting. The main reasons for the occurrence of such a breakdown include pollution or the dumping of the carburetor, as well as clogging of the air filter.

Gasoline trimmer for grass stalls at idle

In case of violation of the optimal settings of the carburetor, it is necessary to clean it and repeated adjustment. You can cope with clogging the air filter of a trimmer for grass by placing it for several hours in a solution with a conventional domestic detergent. If independent cleaning has not helped to cope with the blockage, it is better to purchase a new filter element in accordance with the operating manual.

After the measures, the user will not encounter a situation for a long time when a trimmer for grass stalls in idle and functions only when gas supplies.

They brought a Chinese benzotrimmer for repairs (they said it turned in the back, we are undergoing to start like.

Apart from time to time, from time to time, gasoline trimmers for grass can stall due to the fact that the valve located in the gas tank cover just clogged or stick. To find out, try to use the braid by loosening the gas tank cover. If in this mode the device is working on a dull way, clean the valve.

over, the lawn mower can stall due to the disgusting receipt of fuel in the carburetor. Nevertheless, repair t.e. It works normally at low speeds. Why then the device starts up, ask you? The reason for this is that at first, the fuel gradually runs into the carburetor and is enough to work at high power. The lawn mower does not work at idle. But then it is produced and at huge turns the engine begins to stall. As for the carburetor, here the problem may also consist in the fact that its body is very pulled.

In addition to everything else, do not forget to check the fuel intake hose. The inconsistent may be that it holds weakly or in general cracked.

These are the main prerequisites why the lawn mower can stall.

Air filter

On the pages of the global network, you can find information that the chainsaw of the Stihl 180 can stall due to severe air filter pollution. I would like to refute this not absolutely true information, and say that the STIHL carburetor MS 180 is equipped with a compensator, which is designed and installed in order to make an air focus necessary for the usual operation of the Stihl 180 chainsaw, bypassing the dirty filter. Of course, the power with a clogged air filter will fall a little, but it will definitely not stall. Another capacity may fall due to the wear of the piston, here the repair of the piston chainsaw of the Stihl MS 180 will already be required.

Forbidbenzokos when clicking on gas: causes of their solution.Glumpnbenzokos (trimmer for grass):. Fighting.

Car Engine Stalls or Rough Idle After Fueling Up

idle sensor failure;
clogging of the throttle;
work of the sensor of the position of the trissellain;
Injector or carburetor pollution

The grounds for breakdown can be completely different, therefore, when eliminating them, it will be necessary to operate with all kinds of actions and techniques. If your shoulders are considerable driver’s experience, and you know the features of the car’s work as your five fingers, regardless of the model, then the elimination of this kind of malfunctions will not cause you any problems. And all because such breakdowns are not complex or serious. It follows that you can establish the operation of the car without outside help. Well, if the level of awareness or lack of free time will not give you the opportunity to eliminate all defects yourself, it is better to seek help from knowledgeable people who can save you from unpleasant moments in the shortest possible time.

Trimmer does not start for grass

Like any technique, trimmers for grass are subject to various breakdowns. Often at the beginning of the summer season, the owners of such a tool complain that the trimmer does not start for the grass, and you have to look for a long time to look for the cause of the malfunction.

For those who have acquired a trimmer for grass recently and still on “you” with this technique, information will be useful about why the trimmer for grass is not started and what to do in this case. So, let’s find out what can cause this.

A gasoline trimmer for grass is not started. 10 possible reasons

Before trying to independently establish the work of the tool, carefully study the guide for its operation. Perhaps the information contained in it will promple you with one or another thought. Otherwise, you will have to look for the cause of the malfunction by selection. It may be one of the following:

The cupcan on the rod is not transferred to the “v.””. This is one of the elementary actions, but sometimes beginners forget to turn on the tool before starting it.
Such errors include the absence of fuel in the tank. If the fuel ends, and you forgot about it, just pour into the tank (usually located near the motor) AI-92 gasoline.
Absence, inappropriate mixture or incorrect proportion of engines oil. Ideally, you should regularly add no more than 50 g of oil. This will serve as an additional lubricant and will support the engine of your trimmer for grass in working condition. Also consider that oil is of different types (“synthetics”, “semi-synthetics”, “mineral water”)-all of them affect the operation of the mechanism differently.
If a trimmer mowel for grass does not start after winter, drain the fuel remaining in the gas tank and replace it with fresh. This is especially true for small low.power trimmers with small engines sensitive to low.quality mixture. In addition, during the winter, a precipitate may form at the bottom of the gas tank, which is due to which problems arise with the operation of the device.
Excessive fuel pumping can also become one of the reasons that the trimmer for the grass has not stalled and does not start. Когда воздушная заслонка перекрыта, свечу заливает топливом. It should be twisted and dried, and then inserted into your place and try to launch the engine, holding the gas trigger. It is advisable before this to check it for the presence between the electrodes of the spark. If there is no spark, the candle should be replaced.
Problems with the filter. If your trimmer for the grass starts poorly, remove the air filter and run the tool without it. If everything works out, the filter should be changed to a new. As an option. to carefully clean and blow the old one, but sooner or later the replacement will still have to be done.
trimmer for the grass stalled and does not start? Try to clean the so.called sapun. an element designed to level pressure in the gas tank. Cleaning can be done with a regular long needle. The clogged soundtrack often becomes the cause of the malfunction.
Knives are removed from the car. some models will not work under this condition.
Violation of tightness. You can check this using a pressure gauge. If the pressure begins to fall, you should determine which of the parts of the carburetor is faulty. Most often, carburetor gasket wears out.
Sometimes, after a long period of work, you can notice that the trimmer for the grass has overheated and does not start. Firstly, you should know that you should definitely take breaks. The amount of continuous operation time recommended for this model should be indicated in the instructions. Also, the problem of overheating can lie in a faulty ignition coil or in the air cooling system, which prevents overheating.

If none of these actions has given a result, you should contact the repair shop or service center.

Why and what to do if a trimmer stalls for grass

There are several reasons why the trimmer for grass stalls when the grass. Usually the problem is provoked:

wear of engine elements. piston, bearings, crankcase;
malfunctions with fuel supply. a carburetor can fail in the device, sometimes a malfunction causes a clogged filter;
mechanical damage to hoses, tubes and cables;
disobedience with the ignition chain.

Most often, under a load for one reason or another, an old trimmer for grass, which has long been in operation, stalls for a particular reason. But sometimes the owners of new gasoline devices face problems.

Why is a trimmer for grass stalling when pressing gas, increasing speed

If the trimmer for the grass stalls when you give gas, then the problem is usually a malfunction of the carburetor adjustment. The malfunction often occurs if the device was inaction for a long time, and then received a significant load. Sometimes the unit stalls immediately after increasing speed, if before that it was operated in difficult conditions with violation of the rules.

The following reasons are also leading to problems with the performance of the device:

Fixing A Car Where The Gas Pump Keeps Shutting Off

With stretching or rupture of the fuel hose in the gasoline trimmer, the elements that have become unusable must be changed. If the reason is in the clogged valves and filters in the unit, they are quite simple to clean.

If the reason that the trimmer stalls for the grass is caused by problems with the carburetor, the problems are accompanied by vibrations

Another common problem is that the trimmer for grass stalls with increasing speed due. In this case, you need to find the instructions for the device and carry out the reconfiguration of the unit. Often it is enough to weaken the tightening of the carburetor body.

Why does a trimmer for grass stall at idle

Garden trimmer for grass often stalls even at idle. The reasons for the malfunction are usually simple. First of all, the improper adjustment of the carburetor affects performance. it leads to problems both at high speeds and in idle mode. Turning off the device can provoke clogging of an air filter or throttle.

Sometimes a trimmer for grass stalls if incorrect fuel is used for it. The gearbox for this reason overheats and reduces momentum.

If a malfunction occurs, it is necessary, first of all, to inspect the carburetor unit and perform mechanical repair or configuration. If the cause is of poor.quality fuel, you need to replace the mixture with a more suitable.

What to do if the trimmer for the grass starts and immediately stalls

If the trimmer for the grass does not gain momentum and stalls immediately after starting, the problem usually consists in improper tuning the carburetor. In this case, fuel in the system comes unevenly, the gasoline unit vibrates and cannot work normally. Repair consists in reconfiguring a carburetor unit according to the instructions from the manufacturer.

Engine stop causes fuel supply valve. The element must be carefully cleaned, and then installed back in place. If the lawn mower still stalls immediately after starting, perhaps the valve is too tight and it needs to be loosened. In this case, the fuel mixture will begin to circulate through the system freely, and problems with the performance of the unit will disappear.

In some cases, a gasoline trimmer for grass stalls due to the fact that the hose contains damage that pass the air. During the repair, you need to replace the fuel tube with a new.

Attention! If the damage in the hose is insignificant, it is allowed to simply add a revolution drive. This will allow you to drive out air bubbles from the fuel system.

What to do if the trimmer works and stalls for the grass

Owners of garden gasoline units are faced with the fact that a trimmer for grass stalls at large speeds after a short work. First, the device begins to function with jerks, and then gradually stops.

Typically, the reason is the overheating of the system. gasoline in the carburetor simply boils. A trimmer for grass can heat up if the ignition circuit coil or wire is damaged. There is no point in repairing worn details, they are simply changed to new working.

The use of a trimmer for the grass does not lead the use of not disk, but rotary damper in a carburetor

What to do if the trimmer for the grass overheats and stalls

If a hot trimmer stalls for grass, the situation is a great danger to the performance of the unit. Repair should be carried out immediately, otherwise the device will be completely unusable, and it will be more difficult to restore it.

Overheating of the unit usually cause the following reasons:

The use of inalitions. pour fuel into the tank with precisely with such an octane number that is recommended by the manufacturer;
a large amount of air in the system. for this reason, the enriched mixture releases an excess of heat;
non.compliance with the proportions of oil and gasoline in the preparation of fuel;
The thick layer of soot on the muffler. soot is a good heat.insulating material, the gasoline braid for the grass during operation is very hot and stalls;
The displacement of the axis of the spit.headed head inside the bar. for this reason, the rotation slows down, and the load on the engine increases.

If the gasoline unit stalls, you need to carefully examine it and eliminate first of all possible deformations of the structure. Then it is necessary to study the fuel parameters. If they do not correspond to the recommended, gasoline is replaced with a more suitable. If unnecessary air gets into the system, it is necessary to independently or with the involvement of specialists to adjust the position of the carburetor damper.

Sometimes a gasoline trimmer for the grass overheats and stalls because there is too old fuel in the tank. Use a fresh mixture for the unit, which was stored no longer than two weeks.

Attention! A trimmer for grass will overheat if you use it for too long, or mow with a weak device hard thick grass.

How to avoid breakdowns

Many breakdowns of a gasoline trimmer for grass can really be eliminated if you remove the causes, but if possible, it is recommended to, in principle, avoid faults. Simple measures allow to maintain the unit in a working state:

You need to use a trimmer for grass in accordance with the recommendations of the manufacturer. It is impossible to use a weak device for removing hard weeds on the site, it is also not recommended to use motorcycles in excess of the due time. The gasoline unit needs to be turned off regularly and allow it to cool down.
During the operation of the device, it is necessary to monitor the state of the cooling system. To maintain performance, the channels in the case are regularly cleaned, like the starter’s ribs. The clogging of the system often becomes the reason that the unit stalls from overheating.
After using the gasoline trimmer for the grass, too, you need to clean. In this case, the procedure is not carried out for a hot unit, at first it must completely cool. For cleaning, use solvents, kerosene and other products allowed for use by the manufacturer.
Before cleaning, the motorcycles for storage must be drained from the tank, the remains of unused fuel. If this is not done, the gasoline mixture will fall into heavy components and will clog the channels of the carburetor, which will subsequently cause malfunctions. After draining the fuel, the device is launched at idle and waited for it to turn off.

With the onset of autumn, a gasoline trimmer for grass must be correctly removed for storage. First, the residues of the fuel mixture are drained from the device, and then the unit is disassembled, rinse and clean all removable components.

Before cleaning gasoline motorcycles for storage, you need to evaluate the condition of its parts, carry out the necessary repair and replacement of nodes. Air filter needs to be cleaned. The engine is partially disassembled, rinsed and blown by moving elements, and then applied a new grease. To maintain the piston part, the candle is unscrewed and the piston itself is lifted to the top point, and a little oil is poured into the opening opening and the crankshaft is twisted several times.

Store a gasoline trimmer for grass in winter is necessary in a warm room

Common reasons for the operation of a benzos at low speeds

The problem is when the lawn mower is not gaining momentum, it is mainly found in gasoline units. This is the technique of various models, for example, Husqvarna, Champion, Stihl.

With quality products, such problems are less common than with cheap from unknown manufacturers.

Part of the structural elements with which problems can be associated with visual inspection are available, and to verify the functioning of the remaining nodes you will need to disassemble the motorcycle.

Problems with the engine

If everything is in order with fuel, filters and a candle of ignition, then the next source may be a gasoline engine. He may have the following mechanical breakdowns:

There is a small cable in the carburetor department. He can save and lead to the problem under consideration. Therefore, while engaged in a carburetor, you should first check the condition of the cable, and, if necessary, pull up (but not to the limit). The main thing is not to overdo it with a stretch so that he does not crack under load.

After you need to check the operating settings of the carburetor, which must comply with the parameters given in the instructions. If they are installed correctly, but there is no desired effect, then you should disassemble the part, rinse, clean, blow all its moves and collect it back. The carburetor itself should be without mechanical damage.

If it is impossible to independently restore the performance of the carburetor, it is better to replace it with a new part or resort to the services of professionals.

In the case when the adjustment or replacement of the carburetor does not give the required result, it is necessary to clean the drive mechanism and grease the cable with oil inside it.

Charges related to the engine can be eliminated with your own hands in the presence of the required skills, but it is better to use the services of the service center for this. Its experts will conduct a comprehensive diagnosis of a trimmer for grass and establish the exact cause of the speed drop.

technical issues

The technical problems of the lawn mower mainly occur in the fuel and ignition system. You can cope with them yourself.

Когда ручная косилка не заводится или глохнет, проблема может быть связана со свечой. The dark cargo speaks of poor carburetor adjustment and low gasoline quality.
The reason for the incorrect operation of the trimmer for the grass may be clogged fuel hose. Filters are also often clogged.
Another internal problem. the muffler is covered with soot. From this, the turnover of the grass for the grass falls strongly. Output. you need to clean the muffler.

Important! If the unit does not work due to breaking up the engine, serious problems may occur. In this case, the malfunctions that can be eliminated with your own hands include only the destruction of piston rings

With more serious problems with the motor, if there is no warranty, you should be prepared to visit the workshop.

How to run a stihl mitch

The main steps to launch Stihl mowel:

Before using the gas trimmer for the grass, read the instructions and check the trimmer for STIHL grass for each part. After you can collect it.
An important step is fuel preparation and refueling. Prepare the mixture in a measured container. Gasoline and oil are poured into it in the indicated ratio. Using a funnel, the mixture is poured into a fuel tank.
At the first launch, turn on the ignition without opening the air damper. Place the device on a flat and smooth surface for stability. Now you need to sharply pull the cord from 3 to 5 times. The air damper can be open in any case: the engine is launched or not.

The first launch may require up to 15 jerks. After starting the engine, turn on the non.working refrigerator to warm up. After a while, it stops the button.

The note! This is a universal leadership, since you need to do the same to start Stihl.

In the case of launching an electric trimmer for grass, everything is much easier: you need to read the instructions and act accordingly. Instead of fuel. Electricity

The device is powered by the network, so it is important to provide a sufficient amount of energy so that the trimmer for the grass can get power

After each operation, gasoline and electric trimmers for grass require a thorough examination.

Following the instructions, you can quickly eliminate any minor damage yourself. But sometimes you cannot start the device with your own hands. In this case, it is better to seek help from a professional, especially if it concerns the problem with the engine and the development of speed in the trimmer or lawn mower.

Summing up

When the first signs of incorrect operation of the chainsaw appear, it is worth performing its full diagnosis. In order to avoid damage to the saw as a result of improper maintenance, it is better to entrust the work to determine and eliminate engine malfunctions. And most importantly, you do not need to use a chainsaw with minor defects, t. to. This will lead to even greater problems.

Those who have lawns in a personal plot know that a trimmer for grass is a fairly useful thing that will help to quickly and efficiently put in order or cleanse the weeds of a strongly overgrown area. And, like any mechanism, it also often fails due to various breakdowns. One of the most common complaints from the owners of the device that the trimmer for grass stalls when pressing gas. We offer to understand the main reasons for this phenomenon and identify ways to solve the problem.

Why does a trimmer for grass stall when you press the gas?

Unfortunately, the situation in which the motor stalls when the gas is pressed on the gas for the grass can occur in many cases. Most often, the “culprit” of the problem is the carburetor. This is the most common reason why the trimmer stalls for grass. As a rule, troubles occur when the carburetor is resolved, which is possible after long.term storage, after operation in adverse conditions, strong loads on the engine. Recognizing the “guilt” of the carburetor is easy in the appearance of vibrating movements of the trimmer for grass. If you have experience in repairing a car carburetor, it makes sense to try to repair yourself using the user guide. Although it is much more reliable to give the part to repair professionalals to the service center. Another reason why the trimmer stalls for the grass, when you give gas, there may be a blockage in the fuel valve, which is an obstacle to the normal supply of fuel

It is not difficult to solve the problem by weakening of the valves, after which normal gasoline delivery to the carburetor is possible. If a similar problem occurs, it is worth paying attention to the check valve. the sapun. While in a gas tank, the check valve does not allow the appearance of a vacuum in the tank

When contaminating the soundtress, the air does not enter, as a result of which the supply of fuel ceases. Often, without gaining momentum, a trimmer for grass stalls at a large load. This happens if the cable located in the carburetor is weakened and hanging. It also happens that an overly stretched fuel intake hose at the load is very stretched, cracks and eventually bursts. If such a problem arises, it will be necessary to replace this component.

As you can see, the reasons why the trimmer for grass can stall when pressing for gas, a lot

That is why it is important to monitor the state of your assistant, to check the condition of all systems of the mechanism in time

Where to start diagnostics motorcycles

If the lawn mower does not start or immediately stalls after starting, it is necessary to sequentially check all the main nodes and assemblies. The test algorithm is as follows:

Fuel tank (fuel quality);
Candle and candle channel;
Air filter;
Fuel filter;
Breather;
Graduation channel.

These nodes are most often source of basic problems, which can be eliminated after a thorough inspection.

Check the fuel mixture

Before starting the engine of a gasoline braid for grass, check the presence, and the quality of the fuel mixture. Do not save, do not greedy and “do not smarter” in this matter. The best light gasoline trimmer for grass

Repair or replacement of the piston group will cost you too much (sometimes up to 70% of the cost of a new tool). Prepare the oil fuel mixture strictly according to the instructions. Calculate its number from real needs. Excess gasoline left after work loses its qualities over time.

We diagnose a candle and candle canal

If the quality of the fuel mixture is not in doubt, and the lawn mower stalls when starting, then a flooded candle may be the reason. Here, a regular candle key is suitable for repair (every motorist has probably has a spare candle.

We twist the candle and wipe;
We thoroughly dry it (you should not bake it);
Excess fuel in the chamber we drain through the candle hole and dry it;
We clean the old candle from the carbon on a sugar or a ladies’ file;
We set a gap with a distance of 1 mm (you can check with any coin);
We return everything to place and try to start a trimmer for the grass.

Dry the channel at least 30-40 minutes. Otherwise, there is a risk of re.pour a new candle.

If the working candle is working, the nest, where it is located completely dry, and the lawn mower does not want to start, lubricate the threaded connection with gasoline. It should be slightly moisturized. No matter what wonderful spark gives out a candle, there is simply nothing to light up in a dry chamber.

If the trimmer engine for grass still does not start, such a cause as the lack of spark due to weak contact between candles and a high-voltage wire should be excluded. Lawn mowing trimmer for grass review comparison. If the connection is of high quality, and there are no sparks, most likely, you have “flew” the ignition unit. Here you can’t do without a master, t. to. The part is not repaired, but sold by a whole knot.

Repair Briggs Stratton Lawn

If the engine works is not clear how it starts up

not always, stalls under load. it’s time to make out.

,Glakes. PIF-PAF-PIKH, dripping gasoline from carburetor and other malfunctions on the lawn mowers

Diagnosis of the filters of the lawn mower

Another reason why the gasoline braid for grass stalls is an air filter. To exclude it, try to remove the filter and start a trimmer for grass without it. If it turns out, then you will have to change the air filter to a new one, or at least blow and carefully clean the old.

You can’t start a gasoline trimmer for grass due to contamination of the fuel filter. This is the next stage of our algorithm. Here we check the state of the filter element and, if necessary, change it with the new. When replacing, try not to leave a suction pipe without a filter, this is prohibited by any operating instructions. A braid for grass for grass gasoline

Stihl. Rush can turn into the repair of the piston group of the engine.

Often, “delicate” branded models of benzos are not launched and stall due. The main function of this element is to align the pressure in the gas tank. When clogging this node, a vacuum is created in the tank that prevents the supply of fuel. Eliminate the malfunction can be cleaned by cleaning the sounds. A trimmer does not start for Huter grass. You can use a regular needle for cleaning.

The normal operation of the cos with internal combustion engines can be disturbed due to the entry of dirt into the exhaust channel or clogging of the muffler grid. trimmer for grass gasoline STIHL does not start. There is such a problem on the models of the older generation. You can solve the issue with traditional cleaning and removal.

Trimmer for grass of gasoline does not work at idiral revolutions Evdiral.Ru

Petrol Trimmer for grass does not work at idle

When purchasing a gas cutting, you must be prepared for the fact that, as in all other similar tools, it may also seem breakdowns that will require repairs. But do not immediately run to the service center and pay huge funds to the craftsmen who will assure you in the presence of severe malfunctions in the device.

Perhaps a more common complaint associated with gasoline trimmers: “Gasoline trimmer for grass stalls”. Gasoline trimmer for grass: but he is not all. It works great like a bush. Naturally, a rather harsh fault may be a prerequisite for this. But almost always the situation is even easier than it seems to the 1st gaze. In order to cope with such a discrepancy, at first try to deal with its causes without third.party help, since, having found out the reason, it is even easier to fight with the inconsistency, and at times it is even self.destroyed.

In fact, when the bureau stalls at high speeds, there are a lot of such events. Another. The presence of flaws in the power system. Construction and repair that it just stalls, not on gasoline trimmers. In this case, the gasoline brush will stop at idle. The engine of the trimmer for the grass works quietly, the box does not really heat up even at idle. Problems with the power system may appear due to distortion or incorrect control of the carburetor. Inconsistency can be caused by vibrations that occur during the operation of bench cutting. Incorrect adjustment of a gasoline mowing can be corrected by simply adjusting it in agreement with the requirements indicated in the operational instructions.

The failure of the idle sensor;
A throttle is closed;
The failure of the throttle sensor of the throttle;
Dirty injector or carburetor

The prerequisites of the breakdown can be completely different, therefore, when eliminating them, it will have to be operated on by various actions and techniques. If you have a significant driving experience behind you and you understand the features of the car as your 5 fingers, regardless of the model, then the elimination of this kind of troubles will not cause any troubles for you. And all since such breakdowns are simple and not serious. Why stall a trimmer for grass on a configured carburetor at idle. It follows that you can start a car without third.party help. Well, if the level of awareness or the shortcoming of free time does not give the ability to remove all the shortcomings without the help of others, it is better to seek help from knowledgeable people who will free you from nasty moments as soon as possible.

How to make the necessary repair

To eliminate problems, clean the throttle and make sure that the idle sensor and the throttle position sensor work correctly. Why does the chainsaw does not start or does not stop at idle? There are times when the chainsaw stalls at idle. If the work done did not bring the same results and difficulties again appear after the restart of the car, then it is worth resorting to constructive action. This means that you need to make a complete substitution of the failed equipment for you.

V. Car repair with faulty idle moves:

Each of the above events leads to the idle move of the motor. But the driver will be able to avoid such problems if he is closely watched by the state of his own car and his parts, which require constant care and preventive inspection.

Checking the filter

1st that must be checked. This is a fuel filter.

In some cases, a filter clogged with a mud cannot pass through a sufficient amount of fuel consistency. Accordingly, a fuel lack of fuel arises in the system, which leads to the fact that when pressing the gas rosopila, fuel is burning out, and the new one still does not have time to act, as a result of which stihl ci.rosopili kiosks. Also, with a clogged fuel filter, there may be a noticeable drop in the power of the chainsaw at the highest revolutions, but this is with insignificant pollution.

If the Stihl MC 100 chainsaw stalls eighty at idle, does not gain power when you press gas or even stalls at its entire speed, you need to diagnose the fuel system and check the density of the crankcase. You can do this without the help of others, but for this you need to have certain abilities. If you are not familiar with two.stroke saws, it is better to contact the specialists, because this technique is quite capricious, and the errors are expensive.

Sources:

https://labequip.ru/trimmer-benzinovyj-rezko-zagloh-i-ne-zavoditsa/
https://101benzopila.ru/benzinovyj-trimmer-glohnet-pri-dobavlenii-gaza/
https://hitech-online.ru/tehnika-dlya-sada/trimmer/glohnet.html
https://zip-sma.ru/instrument-i-stanki/benzokosa-zavoditsya-i-glohnet-prichina.html
https://101benzopila.ru/pocemu-trimmer-glohnet-na-holostom-hodu/
https://tehnolev.ru/dlya-chistoty-i-poryadka/trimmer-dlya-travy/pochemu-trimmer-glohnet-na-holostyh-bolshih-oborotah.html
https://101benzopila.ru/trimmer-patriot-ne-nabiraet-oboroty-pricina/
https://labequip.ru/trimmer-patriot-ne-nabiraet-oboroty-pricina/
https://labequip.ru/trimmer-benzinovyj-glohnet-pri-otkrytoj-zaslonke-vozduha/

Articles patriot, stalls