Playing a trimmer for grass of gasoline new Huter. Inspection of the reducer of the lawn mower and its lubrication

The ratio of gasoline and oil for a trimmer for Huter grass

Entering the tool into the work, many are wondering about what assumes and how to run into a gasoline saw. Following a step.by.step instruction, you can achieve the most successful result reflected in the future work of the saw. And so, it is necessary:

• Prepare a uniform composition of oil and gasoline. At the same time, the oil for the running.in should have corporate production, preferably corresponding to the manufacturer of the gas instrument itself. It is described in more detail in the instructions for your saw model.
• Accurately follow the proportions of the injected products (25-30 ml of oil per liter of gasoline) so that the mixture gains the necessary consistency. Patriot chainsaw after replacing the cylinder. In most cases, this determines the octane number of gasoline specified in the same instructions.
• Check the presence of oil poured into the tank and used for chain lubrication by substituting a sheet of paper to the guide tire when the saw is turned on. The proper run.in the new rope of the running.in is also performed after replacing the piston. Patriot chainsaw is running after replacing the cylinder and piston of the bully on the piston. Duration. If the lubricant comes, the trace will appear on the sheet.
• Turn off the inertial brake so that at the beginning of the work do not cause melting the body in the clutch area.
• Perform the saw processing by the method of turning on in idle mode for 15-20 minutes with a canting every half a minute.
• Conduct processing as usual, using first wood and soft wood, without severe pressing. Over time, the density and size of the tree increase.
• How intense and how much the running.in, it depends on the power of the tool itself and the intensity of the process, but in general, it is required to process no more than three hours of total time in active and passive work mode.

But this processing is used not only for new saws. The running.in is also performed after replacing the piston group of the engine. Having a prepared base of specialists and conditions, the company “Sicks for Motors grass” offers engine running.in services with professional introduction to operation, processing the necessary units, checking technical points. But if you have the necessary tools for service tools, all this can be done independently by purchasing oil for lubricating the chain of the chainsaw and other mechanisms, the necessary service mixtures, spare parts and components.

Motobobes can be repaired for various reasons. When working, smoke from the exhaust pipe suddenly appeared, or the motor does not gain the right power, or uncharacteristic sounds appeared in the device. In this case, you should immediately turn off.

Allow you to turn your boat into a high.speed ship. At the same time, you will enjoy in full fishing or walking by water.

How to mix oil with gasoline for a two.stroke engine

The peculiarity of the operation of two.stroke engines is that the fuel is refueling into the tank along with the oil. Each refueling before the operation of equipment requires the preparation of the fuel mixture in compliance with the proportions. How to do everything right? From our article you will learn how to dilute gasoline for a chainsaw, a trimmer for grass and other garden tools.

Fuel mixture preparation instructions

For the operation of garden equipment, it is recommended to buy unhealthy gasoline. Otherwise there is a risk of engine system. Manufacturers advise fuel with an octane number not lower than the AI-90, better AI-92 or AI-95. Individual recommendations for your tools see in the instructions. At the gas station, pour the required amount of fuel into the canister. It is advisable to take a metal one: static electricity from friction does not occur in such a container, which increases the safety of use.

Buy branded oils for two-stroke engines, preferably API-TB or API-TC class. Recommended brands manufacturer should indicate in the instructions for the tool. Also consider their composition. Mineral oils are suitable for use in warm weather. Synthetic, they are less viscous and can be used even in the frost. Semi.synthetic. these are minerals with improved qualities that are universal for any season. See the temperature limit of operation on the packaging

Pay attention to the volume. It is not the proportion of gasoline and oil for a chainsaw is important, but how many fuel mixture you will need for one refueling and how often you will work as a tool

If in your arsenal, in addition to the saw, there is still a trimmer for grass or gasoline and you use this or that tool several times a week, it makes sense to buy a large canister of oil with a volume of 3 to 5 liters. For several mowing for the summer season, it is enough to take a bottle for 1 liter.

At the beginning of work with the tool, the question always arises how much oil to add to gasoline for a chainsaw or a trimmer for grass

It is important to remember that for two.stroke engines the ratio is 1:50, t.e. per 5 liter of fuel accounts for 100 ml of oil

Why is it important to observe the proportions? Excess oil contribute to the appearance of soot on pistons and candles, and its deficiency worsens the lubricating properties of the fuel mixture, which leads to the formation of bully on the piston group and increases the risk of engine breakdown.

The easiest way to follow the proportions of gasoline and oil for the chainsaw, using measuring containers. They have a scale with marks on which it is easy to navigate. Before filling gasoline and oil, make sure that the capacity is clean. Avoid getting into water and dirt. this may affect the quality of the fuel mixture. Pour the gasoline first to the required mark, then share the oil. also to the desired mark. To mix them, tilt the container several times. The liquids are quickly mixed, and the composition will acquire a uniform color, for example, green or red (depending on the composition of the oil).

It’s important to know! In no case do not use plastic bottles of drinks for storage and mixing fuel mixture. Gasoline corrodes plastic

And even if the walls of the bottle are intact, harmful components will fall into the fuel mixture, and with it into the engine. It is very harmful to the carburetor.

It is recommended to work in gloves to protect your hands from gasoline and oil. Also do not forget about the elementary fire safety rules. Mix the liquids on the street so that the vapors of gasoline do not accumulate indoors. Do not smoke during work and exclude other factors that can cause ignition of combustible materials.

Pour the prepared fuel mixture into the fuel tank and close the lid tightly. If you have made more mixtures than you can use it at a time, squeeze it into a separate canister for storage or leave it in a mixture container. The main thing is to close the lid tightly. The finished mixture can be stored for two weeks and used for refueling without risk for the engine. The only condition. do not leave it in the fuel tank. If the tool will not be used for a long time. spent the rest completely or drain.

Specifications

Before making a choice in the direction of a particular model of equipment, you must familiarize yourself with its technical characteristics. The Huter GGT 2500S model is no exception, the operating instructions of which are presented below. This unit is a device whose power reaches 3.3 liters. With., or 2.5 kW.

As a cutting tool, a knife or fishing line for a trimmer is used (by choice). The design has a bicycle handle and a hard drive shaft. Speasing width is 25.5 cm. When consumers consider this Huter lawn mower, they pay special attention to the spindle rotation frequency. In this case, it is 9500 per minute. The landing diameter is 25.4 mm. You may also be interested in the level of noise, which is 96 dB. Weighs the unit 7 kg. The thickness of the used fishing line is 2.4 mm.

How to refuel a trimmer for grass

The finished mixture of gasoline with butter can be stored for no more than 3 months (clean gasoline is stored less). Dilute the fuel in the quantity that is enough for several applications of the trimmer for the grass. In general, prepare:

• gasoline and oil, which is suitable for two.stroke engines with an air cooling system;
• metal canister and a mixture container;
• respirator;
• gloves.
• Pour 1 l of gasoline into a suitable volume of 1 l of gasoline and add 1/2 of the desired amount of oil.
• Mix carefully, being at a decent distance from the sources of open fire.
• Add the rest of the oil to combustible and mix everything again.

General recommendations for refueling a trimmer for grass with a two-or four-stroke engine:

• Place the fuel tank so that the cover is located on top, and then pour the required amount of fuel.
• Do not overfill the fuel tank. This will lead to one of the problems: transferring into the intake pipe and fuel filter, flammable ignition or breakdown of the motor.
• Try to fill the mixture so that it does not spill. To do this, you can use the watering can.
• If you still poured fuel, then immediately wipe it. Put the wiping material, do not accumulate indoors. this is fire hazardous.
• The launch of the device should begin after the canister with fuel is removed at a distance of more than 10 m.
• If there was a long break between the operations of the mowing, then the remaining old fuel be sure to drain.

Why conduct

The running.in has a double target: this is an access to the specified norms of the internal combustion engine, as well as ensuring the safe and long.term operation of all its mechanisms, an increase in the warranty period without breakdowns.

The process of running in gasoline garden technology helps to solve the following problems:

• At the first start of the friction of the parts, it has an increased value, after production it is significantly reduced, which means that the mechanisms wear much less.
• Slightly, by a couple of percent, but still the engine efficiency grows, since the piston-cylinder is spent on the course of the operated pair. With the existing consumption, this leads to an increase in power, with a fixed power. to a decrease in fuel consumption.
• Thanks to the competently carried out, all the elements of the motor are lubricated to the necessary extent. The combination of moderate load and operation at the necessary revolutions relieves the new engine from overheating and at the same time prepares it for normal operation in conditions of possible hard work.

Working scheme of gasoline technique

If there is no indication of the initial period of operation in the instructions for a chainsaw or trimmer, this sequence of actions should be followed:

• Mix gas and oil in the proportion, which is indicated in the instructions for a normal working regime or at the very saw in the area of ​​the bay neck or gas handle. It is allowed to increase the amount of oil by 10. 20% of the norm.
• Start the engine, taking into account the features of a particular model.
• Having given the saw to work for 15. 20 seconds at idle, you need to press several times, and then hold the gas handle in order to work as the clutch and the chain set in motion.
• Start work by choosing branches for this, branches or thin trunks. It is advisable to carry out the run not on dry, but fresh wood. After 5. 10 minutes of working with a periodic transition to idle (no more than 20% of the total work time), drown the saw.
• Repeat the cycle, increasing the working hours to 10. 15 minutes. After that, the saw can be considered running.

Safety measures when spent

What are the safety measures when working with a trimmer? There are several simple and understandable points, following which, you can avoid dangerous situations and minimize the possibility of injury:

do not use a trimmer for grass in raw and wet weather (especially an ethletric trimmer for grass); In front of mowing, dress in dense clothes so as not to injure the skin with pieces of grass of stems flying away from the disk or fishing line with high speed;

observe a distance of 15 meters from other people and pay attention to the signs that others can serve; use headphones or berushi;

• Using an ethletric trimmer for grass, make sure that the wire from the extension cord always remains behind;
• put on dense rubber boots, which after work are easy to clean;
• use gloves and protective glasses to avoid small pebbles in the eyes and respiratory tract;
• Upon an injury, immediately consult a doctor.

In addition to the above, do not forget to look around, suddenly an obstacle awaits you ahead or side. Suburbating the bar with the blade into thick thickets of grass, it must be remembered that there can be stone, stump, or berries (for example, strawberries). Working with a trimmer requires composure and attentiveness, but by understanding simple rules, it will become familiar, understandable and will bring only positive emotions from the results obtained.

Manual gasoski: weight and handle type

Sometimes the buyer is mistaken in that there is no need to take the weight and type of handle when choosing an unit. This is an erroneous opinion. After all, the uninterrupted operator’s work will depend on weight. The heavier the unit, the less time you will work out.

As a rule, powerful trimmers for grass can weigh from six to ten kilograms. If you decide to choose just such an unit, then you need to closely study its configuration. Such models always have shoulder straps that greatly facilitate the work.

When conducting a review of models, pay attention to the type of handle. After all, working with a trimmer, you must hold it tightly and confidently

Most manual benzocosyles have a T-shaped handle, it is convenient and practical.

Why cannot be drove at idle

There are many videos on the Internet, entitled as a “proper run.in saw”, where you can see the assigned unit, quietly rumbling at idle, removed from different angles. You can’t do this!

While working at idle, the engine operates at the lowest revolutions, but long-term work in this mode is destructive for the cylinder-piston group. The fact is that the fuel does not burn out completely, part of it settles on the walls of the cylinder and the bottom of the piston in the form of a carrier, interferes with the work of compression rings, works as an abrasive.

In addition, with the clutch turned off, the flywheel, on which the card of the crankcase is mounted, rotates slowly and does not provide proper cooling. As a result, the motor overheats, bulletin appears on the piston and cylinder, which leads to decompression, the saw loses power and stalls periodically.

Working scheme of gasoline technique

If there is no indication of the initial period of operation in the instructions for a chainsaw or trimmer, this sequence of actions should be followed:

• Mix gas and oil in the proportion, which is indicated in the instructions for a normal working regime or at the very saw in the area of ​​the bay neck or gas handle. It is allowed to increase the amount of oil by 10. 20% of the norm.
• Start the engine, taking into account the features of a particular model.
• Having given the saw to work for 15. 20 seconds at idle, you need to press several times, and then hold the gas handle in order to work as the clutch and the chain set in motion.
• Start work by choosing branches for this, branches or thin trunks. It is advisable to carry out the run not on dry, but fresh wood. After 5. 10 minutes of working with a periodic transition to idle (no more than 20% of the total work time), drown the saw.
• Repeat the cycle, increasing the working hours to 10. 15 minutes. After that, the saw can be considered running.

How to start a motorcycle

The peculiarity of any technique with a two.stroke engine is a hard algorithm of cold launch, which must be strictly observed.Good afternoon, dear subscribers and guests of the channel.

The other day, a man asked me to see his mower.

The complaint was that the tool would not start. The client said that he bought a mower recently, worked only once. An attempt to start a motorcycle for a second time was unsuccessful.

Such leaks indicate that the mower shifts fuel, but the user practically did not work, and as I later found out from the client, they appeared during an unsuccessful launch.

Now everything fell into place. This lawn mower is completely serviceable, but the client would not be bad to read the instructions, especially the section in which the process of “cold” launch is described.

The result of proper run.in a gasoline trimmer for grass

After you have been running the lawn mower by the instructions, as a result, we get a tool ready to work. Of course, it is best not only to read the stages, but also to see the crowding on the video from specialists. The result of the correct actions will be obtained:

• trouble.free operation of the benzo tool for a long time;
• high.quality start of the device and stability of the submitted power;
• lack of unforeseen repairs of a trimmer for grass after high.quality pounding;
• Lack of overheating.

In this regard, the primary processing of the Chinese braid for grass is an integral part of the quality work of the device that can work flawlessly using benzos knives or cutting fishing lines of different diameters when processing territories available in the special store “Spit for grass”.

Peculiarities

It should be noted that a gasoline braid for grass is controlled very simply. It is enough to see how other users use this unit to start using it fully. The performance of the main technical functions is intuitive and does not require any difficulties in practice. Correctly driving a gasoline trimmer for grass is also not difficult. over, there is almost no difference between devices of household and professional categories.

The key difference is the type of motor. On technology for professionals, it is more powerful and gives more revolutions. A two.stroke engine is more often used in household models. Four.stroke units are more reliable and give out a greater effort, so they are suitable for special conditions, difficult and overgrown sites.

In addition, we must consider whether there is a cutting device in the supply set.

The first trigger

When everything is checked and the prepared fuel mixture is filled in the tank, the moment of the first launch of the trimmer for the grass until it is launched. To do this, follow the following manipulations:

• Place the brush on a flat horizontal surface;
• Transfer the throttle lever to a closed position;
• We inject several fuel shocks for beginners in a carburetor;
• Turn on the ignition;
• Gently pull the starter cord until you feel resistance;
• Then make a cord 3. 4 sharp jerks until the brush begins;
• After starting, open the air damper.

Characteristics

It should be noted that the gas braid is very simple to operate. It is enough to see how other users use this device to start using it completely. The performance of the main technical functions is intuitive and does not require difficulties in practice. It is also easy to properly run a gas trimmer for grass. over, there is practically no difference between devices in the household and professional categories.

The key difference is engine type. As for the technology for professionals, it is more powerful and gives more speed. A two.stroke engine is more often used in household models. Four stroke units are more reliable and require great efforts, so they are suitable for special conditions, difficult and overgrown sites.

How to run in parts?

The described launch method is quite suitable even for Chinese technologies. But sometimes it is impossible to start the first time or the trimmer for the grass stops immediately. In this case, similar manipulations are performed when closing the air duct valve. If then nothing works, you need to contact a specialist. If the system works correctly, never start the device immediately.

First, the engine should work at idle for 5 minutes. Important: if the instructions indicate another time, you must follow its instructions. During heating, it is necessary to adjust the air supply. Setting various provisions of the air damper lever, they guarantee that the cutting part is not moving. Having waited for warming up, completely open the damper and set the power by 50% of the maximum.

In this position, the lever is held within 20. 30 seconds. Having lowered the gas to a minimum, let the braid work 30-40 seconds. Then they set the power by 20% and wait 10-15 minutes. After that, the engine turns off and remains at rest for ¼ hours. When a trimmer cools for grass, the engine starts in accordance with the already described scheme, but first the damper opens.

Gas maintenance should be avoided, since poorly processed parts can be damaged. Long idle is also contraindicated. This will lead to overheating. This completes the engine operation, after which you need to start the transmission. This procedure is performed on an open area where soft fresh grass grows. It is mowed by 5. 10 minutes without a break, periodically processing gases with a capacity of 50-75%.

After such a session, the mowing stops for 20 or 25 minutes. Typically, 3-4 cycles are enough for the proper operation of a trimmer for grass for many years. Most often they try to start the device until the first refueling is completed.

Features of Kustorez See in the next video.

The correct first launch and launch of a bush cutter are very important steps when starting a new tool. On the one hand, they can save a gasoline engine motorized engine, laid down by the manufacturer, since at this stage there is a crushing of mobile units and parts. On the other hand, the first necessary skills for working with a trimmer are acquired when we are talking about the first tool in my life.

• Preparation for the first launch of a bush
• Examination and lubrication of the gearbox
• Preparation of the correct fuel mixture
• The first trigger
• The start of work on starting brushes for gasoline

Playing Chinese lawn mower and operation issues. Practice

In this video, we will indicate the most all.produced error when running in gasosos and chainsaws. Buy spare parts.

Playing Chinese lawn mower and operation issues. Practice

I continue to share the first impressions of the Tatra motorcycle. In this video I will briefly tell about the first start.

The first launch and run-in Motokos Tatra BCU-73

how to run the lawn mowers and chainsaws correctly.

mechanical. to defend and store gasoline for work not in metal containers and not longer than 1 (one) month, otherwise it oxidizes and loses its properties;

chemical. impurities and additives should not be present (they have different speed, degree and temperature of combustion). Old gasoline turns yellow or reddish, and impurities have pungent smells of bitterness (for example, creosot) or acid (for example, methyl alcohol).

The proportion of the fuel mixture is 1:50 (2%) or 20 ml/cm3 of oil per 1 liter of gasoline. For example, pour half a gasoline measure into a transparent plastic bottle (1 l), then administer a two.stroke oil with a medical syringe (20 ml/cm3) and mix, add gasoline and mix thoroughly. If the quality of gasoline is doubtful or the working conditions are difficult, then the amount of oil can be increased to 22-25 ml/cm3. Before each refueling, shake the mixture! Store the resulting fuel for no more than two weeks! If the color of the mixture has changed (from the color of the sea wave, for example, brown), then it is not recommended to use it!

We proceed to running the lawn mower

After starting, do not rush to immediately run the trimmer for the grass. Let the engine idle for 5 minutes. While heating is going on, adjust the air supply to the air damper with a lever so that the rogue with a fishing line or with a knife does not rotate. As soon as the tool warmed up, we completely open the air supply to the corresponding lever to the “ON” position and squeeze the gas trigger for 1/2 and hold the seconds of seconds 30. Then we drop the gas, let the trimmer work on xx 3040 seconds. In this mode we continue 10 minutes 15. Then we mock and let it rest for 15 20 minutes.

Having cooled the lawn mower, we continue to run the engine according to the previous scheme. Start a hot, a trimmer for grass should already be with an open air damper. Try not to hold the gas for a long time, since the movable details of the tool only rubbing each other. And do not let the engine work at idle for a long time as it can overheat.

The next stage is the run.in a gas reducer gearbox for grass. To do this, select a plot with soft young grass. Kosim 5 10 minutes with 1/2 2/3 from full gas. After we take a break for 20 25 minutes. Repeat the cycle 3 4 times.

In general, therapist for the lawn mowing according to the described algorithm is carried out until the fuel mixture in the tank is fully generated. After which the tool is ready for long.term work. In the process, follow the temperature regime of the gearbox and the motor. They should not overheat.

Motokosa service (trimmer for grass)

Engine. The air filter should always be clean (without dirt or sawdust); foam filter must be wetted with oil. The fuel filter must be checked once a week, in the case of intensive use of the tool, if necessary, to replace it in time. Checking the tightening of nuts and screws. before starting work. Cleaning from a muffler carrier (or its grid) and candles. if necessary.

Cutting discs. The cutting faces should be well and properly sharpened using the necessary templates and files (emery), in compliance with the angles of the cutting parts depending on the brand of the disk. Double.sided disks regularly turn over 180 ° and wear out evenly. A dumb disk or a disk with poor or improper sharpening does not cut well, and thereby overloads the engine, which leads to an accelerated reduction in its motorcyclear.

Trimmer fishing line and trimmer heads. Use only a special braid line for a trimmer. do not use wire or metal cables! Install a fishing line for a trimmer only of the diameter that is recommended by the manufacturer. Wind on the bobbin tightly, but do not cross the turns. Clean the mowing head from dirt and, if necessary, lubricate. A worn or deformed head can disable a gearbox and/or shaft motorcycles.

Corner gearbox. As necessary, cleaned of dirt (such a “fur coat” does not allow the gearbox to cool normally) and add a consistent lubricant of Husqvarna, or similar, for a reducer pair.

Protective covers. It is forbidden to work without a protective casing. this is dangerous for the life of the operator and others, and can also overload the motor motorcycles. For each type of cutting equipment, only its own protective casing, provided for by the manufacturer, should be used.

Independent repair of motorcycles

It should be noted that it is not always possible to independently repair motorcycles, but in most cases, small repairs are possible for everyone.

If a trimmer motor broke for grass, and you are not a car mechanic and not an electrician, it is better not to try to fix the mechanism. There is a chance that you cannot collect it back. There may be such problems: low compression in the engine, the engine jammed, the carburetor failed. If these phrases do not tell you about anything, then you should not repair the motorcycle for the picture and intuition.

It should be noted that the maintenance and repair of the chainsaws and motorcycles are largely similar.

A trimmer for grass consists of a bar, a motor (happens from above or below), and a mowing head with knives, various additional elements. What can be repaired here yourself?

air damper; 2. handle; 3. engine stopping device; 4. throttle control lever;

5-bracket limiter; 6. bar; 7. protective device of cutting devices;

1) If the swallowed a toggle switch is turned on, and you are familiar with simple electrical circuits and are friends with a soldering iron, solder and rosin, then you can easily replace the toggle switch with a new. They are sold in electrical equipment and lighting stores.

2) if the wire limiter from the mowing head has disappeared, it can be wrapped with flexible copper or aluminum wire to the bar. You can also make a new mount from a strip of stainless steel.

3) If a fishing line for a trimmer was torn in the drum of a mowing head, there is nothing easier than replacing it on your own. You can, of course, just buy a head for motorcycles separately and replace it, but a fishing line for a trimmer will cost a hundred percent cheaper. The optimal material here is a fishing line for a trimmer from 0.9 to 1.5 mm, nylon or nylon. Measure the diameter of the used fishing line at once, before it ends completely. Thinner. can break, thicker. causes engine overheating and unnecessary vibration. You need to disassemble the drum and wind the fishing line for a trimmer manually, then collect the drum.

4) if the bar breaks, it can also be repaired by scraping and gluing to wooden rails or iron brackets.

5) If strong vibration has begun, and the engine began to work “unevenly”, perhaps a motorcycle has a lubricant. Any trimmer for grass is easily disassembled, it is recommended to lubricate it with technical oil at least once a year.

7) If the trimmer for grass is equipped with plastic knives, and they were deformed for some reason, there is a way to replace them with metal. To do this, you need to make several stainless steel knives. This is difficult at home, but a familiar turner operating in an industrial enterprise or factory will be able to save the situation. Knives are attached to the shaft using a sleeve with a puck. Such modernization will lead to the fact that a trimmer will become possible to mow grass of any stiffness. But caution when handling such a trimmer should increase.

8) the engine does not start? To start a braid, sometimes even hot, it is necessary to completely close the damper to enrich the mixture. Check the flow of gasoline, clean, if necessary, replace the glow of incandescent.