Quick Change Of Fishing Line With Trimmer

In this manual, we will step by step analyze the entire replacement process. Looking ahead, there are two ways to tackle the trimmer spool with fishing line. There is no fundamental difference. The difference is that in the first case there will be one fishing line, folded in half, and in the second there will be two lines of such lines.

Replacement Preparation

Disassemble the trimmer spool

For clarity, the mowing head (spool) was removed from the lawn mowers. To replace the fishing line, you do not need to remove it, everything is done locally. It does not take much time.

We disassemble the trimmer spool. It rests on the latches-latches. Remove the cover by pressing on the latches. If you do not have enough effort with your hands, then use a screwdriver.

The spool consists of the following:

• Spring housing
• Locking lid
• Button Coil

The principle of action is as follows. By pressing the button, the coil presses on the spring and exits the locking grooves in the spool cover. While holding the coil in this state, you can twist, thereby adjusting the length of the fishing line. When you release the button, the housing spring returns the coil to its original fixed state.

Disassembled Trimer Spool

Bottom on the coil there are several holes for different diameters of the lines. Different trimmer manufacturers may vary. In some cases (as here) they are signed, in others not.

These holes are needed to fix the fishing line when replacing it. After winding on a woman’s fishing line, the ends of the latter are inserted into them. This is necessary so that the scaffold does not unwind at the time of installation of the coil in the trimmer housing. In other words, it facilitates the replacement of fishing line.

Fishing Line Holes

There are models without specifying the diameter of the consumable. Then, in order to find out what the maximum diameter of the scaffold can be used, it is tried on through the holes for withdrawing fishing line from the body of the trimmer spool (see figure below).

Fitting on fishing line outlets

The reel has two sections for fishing line, separated by a partition. They may not be. They are needed only to distinguish and facilitate winding of the consumable.

Two sections for fishing line

Initially determined with the required length of the loess. The latter is wound in one of the sections of the coil so that it does not go beyond its limits. In this case, 3 mm was wound, the length was about 2 meters. Those. For two sections you will need a 4 meter cut. This is for the 1st method. For the second method, you need two segments of 2 meters.

Determination of the required length of fishing line

Now you need to figure out which side you need to wind it. To do this, many manufacturers of trim tabs on the coils apply special designations such as in the figure below.

Special designation on the reel

If such designations were not found, then you need to pay attention to the body of the spool. There is without fail an arrow that indicates the movement of the mowing head. The line is wound in the opposite direction.

Designation on the spool housing

First way

Bent in half fishing line

The prepared segment (in this case, 4 meters) is bent approximately in half. One segment should be 15-20 cm longer and inserted into a special slot located on the dividing partition.

The fishing line is inserted into the slot

In a previously defined direction, a fishing line is wound. This is done in a tight fit, the line is neatly distributed. In this case, you need to wind a segment that is longer in the section that is closer to the button.

There are designs in which the division of the coil into two sections is not provided. This does not change anything, the fishing line is wound in a similar way. It is only necessary to ensure that the segments do not overlap among themselves.

The first segment that ends at the bottom of the coil, i.E. One that is closer to the fixing holes.

This tip is placed in the corresponding diameter hole. The fishing line is firmly fixed.

The fishing line is firmly fixed

A long section is wound another half turn. There it is fixed in a similar way. In this case, the segment crosses another section of the coil.

A long section is wound another half turn

The fixed ends of the wound fishing line are inserted into the holes of the trimmer spool housing.

The fixed ends of the wound fishing line are inserted into the holes of the trimmer spool housing

The coil is attached to the body. The ends of the fishing line are pulled with force so that the fishing line previously fixed in the holes of the reel springs out. This is easily determined by the characteristic sound (click).

The ends of the fishing line pull

The button coil is latched into the trimmer spool housing.

Coil with button snap into the trimmer spool housing

Replacing the fishing line was successful. In this case, you need to install it back on the trimmer and you can start mowing the grass.

It should be repeated, you do not need to remove the spool from the trimmer. This was done to make the process of replacing the fishing line easier. You can disassemble the spool in place, wrap it on a reel and put it back.

Successfully replacing fishing line

The tips so that they do not hit the trim cover can and should be trimmed.

Method 2. Two segments

Two wound lengths of fishing line

Method number 2 fundamentally no different from method number 1. The only difference is the two winded pieces of fishing line, instead of one.

The end of each segment is bent.

Two special locking sockets

There are two special locking sockets on the coil (see figure above).

Start winding the fishing line

They hook onto it with a hook formed earlier on the fishing line, and begin to wind the fishing line.

Winding is carried out in a special order.

The winding should be carried out in the following order: first the bottom line, i.E. The one that is closer to the fixing holes at the bottom of the coil, and only then the upper one, i.E. One that will overlap the bottom section.

The bottom line is wound

The tips are made into the holes in the body of the trimmer spool. They are pulled up to a click, which indicates that the line has come out of the clips.

The tips are threaded into the holes of the trimmer spool housing

The coil is fastened into the housing. The fishing line in the spool is replaced.

The fishing line in the spool is replaced

Video: How to wind a fishing line on a mowing head trimmer or lawn mowers

How to wind a line onto a mowing head of a trimmer or lawn mowing machine

Replacing the fishing line in the trimmer: 2 easy ways

Feedback from our readers is very important to us. Leave your rating in the comments with the argument for your choice. Your opinion will be useful to other users.

I want to devote today’s article to the sore topic of summer residents and gardeners of the entire post-Soviet space “How to refill a fishing line into a trimmer.” Not many trimmer manufacturers answer this question in their operating instructions. Therefore, it is difficult for ordinary gardeners to figure out how to do this correctly.

I want to start with a brief description of the technical characteristics of the trimmers.

So, trimmers are electric and gasoline. The cutting element of the trimmers can be a fishing line and a knife. The fishing line is ordinary, four. Pentahedral and intertwined (in the form of a pigtail). Knives come in 2, 3 and four blade blades. Knives are also plastic and metal.

The feed system of the fishing line from the trimmer is manual, semi-automatic and automatic.

Development engineers who create new models of trimmers clearly calculate the diameter (thickness) of the fishing line and the number of knife blades according to the power of the trimmers. Otherwise, the engine is overloaded, which as a result leads to its breakdown. And this is an additional and significant cost.

Today on the market are trimmers:

With one nozzle. Only fishing line. With two nozzles. Fishing line and three-four-blade knife. With one nozzle. Only a three-four-blade knife.

Our Kulibins long ago learned to improve any mechanisms. So, for example, some gardeners make successful, in their opinion, replacing the fishing line with a metal cable, or fishing line. But at the same time they do not think about the safety of their and their loved ones, because, as a cable with the power of a working trimmer, it can easily break out and not only injure the mower and others, but leave it crippled for life. Using fishing line can and gives a better effect, I have never personally tried it than fishing line for trimmer, but this work has a number of inconveniences: when it comes into contact with solid objects it dissolves or can simply be pulled out of the reel without limit.

So what is called closer to the topic. I give an example of how to fill a fishing line into a trimmer (BOSCH Art 30 trimmer). Everything is very simple. We started.

After you have chosen the fishing line for refueling, you need to cut off the necessary amount of fishing line, because all the fishing line in the skein is not wound into a reel.

Cut off and start winding.

Remove the coil and the protective cover from the coil.

They took off. We fix one end of the fishing line into the gap and carefully and evenly wind the fishing line.

The amount of fishing line should be such that the protective cover of the reel closes and the line on the reel unwinds itself a little.

The second end of the fishing line is planted in the hole on the protective cover.

Next, take the coil and the protective cover of the coil. We sink the end of the fishing line from the reel into the metal hole on the protective cover of the reel. Tighten the fishing line a little.

We put it all on the trimmer. Turn the coil clockwise until it clicks.

Secured. Now connect the trimmer to the network. We put the trimmer in the starting position for the job. Turn on the trimmer. The excess length of the fishing line will be cut off on the cutting blade.

Trimmer Coil

That’s all starting work.

You can watch the

A little tip. Make sure that the fishing line does not come into contact with solid objects when cutting. With this contact, the fishing line will be cut. And since, in this trimmer, the fishing line is not fed automatically, then you have to stop the work each time, remove the reel and re-release the fishing line.

In my trimmer, in addition to the standard line for mowing the lawn, there is still provided a thick fishing line for mowing coarse weeds. It has the shape of a pigtail, i.E. Three fishing lines are tightly intertwined. Such a fishing line has its own reel.

Thick fishing line

It is stored at the top of the trimmer body.

Spare coil storage space

Installing such a fishing line into the reel is very simple. According to the internal circuit inside the reel. We insert the center of the fishing line with a metal mount at the top of the reel, and draw the ends of the fishing line along the grooves and bring it out.

Reinforced Fishing Line

Such a coil is attached to the trimmer as well as a reel with ordinary fishing line.

• What types of woods are
• How to remove or refill a fishing line in a trimmer

Since we considered the choice of the trimmer in the previous article, today we will tell you how to properly trim the trimmer with a fishing line, and which is better to choose based on the working conditions.

After you bought a trimmer and began to use it actively, sooner or later the question will arise about replacing the fishing line, since this is the most wearing element in the tool, then intensive use of the trimmer will lead to frequent replacement of consumables.

What types of woods are

The most common type of fishing line, which is suitable for almost all types of coils. Round cord. This is an ordinary fishing line suitable for mowing juicy grass, but mowing dead wood with it will be much more difficult, and even more so it can not cope with the bush.

As a rule, the diameter by which young grass can be mowed does not exceed 1.6 mm. The thicker the thread, the more coarse grass it can overcome.

There are fishing lines with sharp edges in the form of an asterisk or square, this option is more suitable for mowing dry grass just due to the existing sharp edges, but its disadvantage is more wear and tear and is inferior in strength to round cord.

There are fishing lines with improved aerodynamics with characteristic dents, scales and notches, such a product makes less noise, but they are used only on lawn mowers, since the exit of such a thread from the reel is difficult, it is used most often with discs into which segments are inserted. The disadvantage of this product is its fragility.

Most often in gas trimmers with an engine power of more than 1.5 hp apply cords with a metal cable inside.

This thread is ideal for mowing dry grass and small bushes. The presence of a core positively affects the wear resistance of this material.

The disadvantage of such a cord is its price, which is significantly higher than the listed opponents.

How to remove or refill a fishing line in a trimmer

It takes about 10-15 minutes to wind the line. What is a trimmer coil? Plastic case with a cassette inside, on which there is a special hook for convenient winding of fishing line.

Almost all trimmer coils have a similar mounting principle, this is the central screw-button, when pressed, it becomes possible to pull the fishing line of the required length. The photo below shows some examples of different coils for trimmers.

The bobbins of the trimmers, the motor of which is located near the ground, have a different mount to the axis of rotation, they have two buttons on the spool located on the sides that need to be pressed, otherwise the thread replacement is no different from other cassettes.

The principle of the correct winding of the fishing line is similar in all of the above cases, so for example, consider the standard version with two antennae.

To remove the reel with fishing line, it is necessary to unscrew the screw located in the center, but note that the thread there is left, so you have to turn it clockwise, this is done specially so that during operation it does not open under the influence of centrifugal force.

Next, using a screwdriver, disassemble the head and take out the reel, on which the fishing line is directly wound.

Having measured the necessary length and folded in half, you need to fill the fishing line into the reel, removing, in the end, its ends opposite each other (for this there are special slots for fixing).

After this, it is necessary to assemble the head in the reverse order by threading the ends of the cord into two corresponding holes.

If you have doubts or it’s not entirely clear how to charge the fishing line to the trimmer, we recommend watching the: how to wind the fishing line into the lawn mowing properly.

In this, the instructor will open the trimmer head in steps, measure out the required amount of fishing line, usually from two to four meters, and demonstrate assembly and installation on the trimmer.