Starter for a heavy one -axle tractor with your own hands. How to choose a starter for a single tractor?

10th October 2022

Installation of an electric steamer on a single.based Neva tractor with your own hands. Starter for one.time tractor: device, repair and maintenance recommendations

To date, various equipment is used to cultivate land and agriculture. Everything is aimed at reducing the level of physical costs by shifting certain tasks for equipment. Additionally, due to this, the performance increases. Quite often, such a device as a single tractor is used to treat soil. This technique consists of many individual elements and mechanisms that over time can fail. In this case, it is required to consider such an element as the starter of the walk.behind tractor, its variety and device.

Gasoline starters on MTZ belong to the type of PD-10. Когда происходит его запуск, то редукторы начинают передавать крутящий момент на силовой агрегат, раскручивая его постепенно. The advantage of a gasoline device is unpretentiousness, the ability to use not very high.quality fuel for work, which does not affect performance at all. An electric device is installed on MTZ-80, the power of which is carried out through a special mechanism connected to the battery. Typically, this species is needed for tractors with powerful engines designed to perform prolonged loads and constant operation. Electric requires a mandatory connection to the motor so that the coupling can transfer to the flywheel torque.

Thus, which starter is better to put on an MTZ, the owner of the tractor must choose on his own. Modernization depends on the types of work performed and technical characteristics of the machine itself. Climate and weather conditions are important.

The advantages and disadvantages of the characteristics of the universal T-30 universal tractor is important

The block does not work or works unstable

It is logical to start the analysis of possible breakdowns with this situation: the cascade unoic tractor starts and immediately stalls. Or completely stopped starting. The following reasons are most likely:

excess gasoline (the moisture of the candle speaks of it);
In models with an electric starter, the problem often lies in the discharge of the battery;
The total power of the motor is insufficient;
a failure arose in a silencer.

The solution of each of these problems is quite simple. So, if there is a lot of gasoline in the gas tank, they must dry the cylinder. After that, they start a single tractor with a hand starter

Important: before that, the candle should be twisted and also dried. If the manual starter works and there is no electric, then you should charge or replace the battery

If the engine does not have enough power for normal operation, it must be repaired.

To reduce the likelihood of such a breakdown, it is necessary to use only gasoline of impeccable quality. Sometimes a carburetor filter is clogged due to poor fuel. You can clean it, but better. we will repeat it again. to perceive such an event correctly and stop saving on a fuel.

Sometimes it is required to adjust the carburetor KMB-5. Such devices are placed on lightweight motoblocks

But therefore, the importance of their work is not reduced. After the repair of the failed carburetor, only suitable gasoline brands should be used for washing individual parts

Attempts to remove pollution using a solvent will turn into deformation of the rubber parts and washers.

You need to assemble the device as accurately as possible. Then bends and damage to the parts will be excluded. The smallest parts of the carburetors are cleaned with a thin wire or steel needle. Be sure to check after assembly whether the connection of the float chamber and the main case is tight. And also should evaluate if there are problems with air filters, are there any fuel leaks.

Actually, the adjustment of the carburetors is carried out either in the spring, when the one.axine tractor is first rolled out after the “winter vacation”, or in the fall, when the device has already worked for a very long time. But sometimes they resort to this procedure at another time, trying to eliminate the shortcomings that have appeared. A typical sequence of steps is as follows:

heating of the motor in 5 minutes;
wrapping to the limit of adjusting bolts of the smallest and largest gas;
twisting them for one and a half turns;

installation of gear levers on the smallest move;
task of small revolutions using a throttle;
The gasping of the gas screw for setting the idle speed. with a continuously working motor,;
jetting of the engine;
Assessment of the quality of adjustment by new launch.

To exclude errors in the process of setting up the carburetor, you need to check each step with instructions for operation. When the work is done normally, extraneous noises in the motor will not appear. over, malfunctions will be excluded in any of the working modes. Then it will be necessary to observe the sounds that the one.based tractor makes. If they differ from the norm, you need a new adjustment.

Starter for a single tractor. device, repair nuances, prevention

Motobobes are known for their constructive features. In particular, the fact that two starters are used for their use at once. An auxiliary or spring starter helps the main one to start properly and quickly. But, if the auxiliary starter suddenly fails, then you have to think about how to repair a hand starter. Perhaps even with your own hands.

By the way, the spring option is not the only. A manual starter for a single tractor is quite common, it is common in it is much more simple to operate. It is easier to install it, even if the user does it with your own hands. It has a completely uncomplicated design:

drum building;
coil;
The spring, or rather, two: large and small;
washer;
cord;
tongues;
bolts and nuts, without which neither a mechanical nor an electric starter is collected.

In the collected form, this looks as follows: the cord is attached on the coil, and it is fixed on the core of the drum building. There is a special space inside the drum, where a large spring is located around the axis. It is she who is responsible for ensuring that after scrolling, the starter returns to the previous position.

How a hand starter works

When the user of the walk.behind tractor pulls sharply by the starter handle, the entire mechanism installed on the machine is moving in motion. The initial rotation passes to a single tractor, or rather to the engine, and it starts. As a rule, for the engine the engine, you need to sharply pull the starter handle abruptly in order to properly disperse it.

Small nuances for repair

As already mentioned, the manual starter is the least whimsical. In most cases, the repair of the starter is to correct the places where the springs are attached. They sometimes extend. Or, perhaps, the starter repair will be to replace some parts with new. Sometimes you need to replace the starter cord.

In order to determine a specific malfunction, you will need to disassemble the area of the walk.behind tractor in which the starter is mounted. In what order the repair should take place:

First you will need to arm the scheme from the manufacturer. It describes how and where all its details are attached to the motornote. You will also need a key with which you will unscrew and remove the nuts.
Then you need to disconnect the starter. It is better to photograph and write down everything regarding its fastening scheme. Otherwise you may not collect it back.
In the center of the drum you will see the puck that you need to unscrew. This is the upper washer. When you remove it, disassemble everything that you will find inside and check if there is any damage to any element.

What breaks most often?

The easiest way to fix what you can simply replace. For example, if you have a cord for a walk.behind tractor, then you can change it to a new. As for the large spring, everything is also simple here: study the places of its fastening. There are two hooks at its ends. If one of them is not, then it is worth heating the spring, bend its end in the form of a hook and it will again be ready to serve. However, if the hook broke due to fatal fatal, then it will be more advisable to replace the spring.

Spring mechanism

The manual structure is simple, but it can be improved to save time and time. For example, put an electric steel for a walk.behind tractor. Then you will not have to pull the handle every time. But keep in mind: this design is not suitable for all starters with manual launch. And the electric circuit that you choose for installation may not be suitable for every engine.

In these cases, it is worth paying attention to the third option: the spring mechanism of engine start. After installing it on the engine, just shift the motor block handle, and it will immediately start. This type of kickstarter is based on the semi.automatic work of the spring. It accelerates the engine installed on a one.axle tractor, without the need to pull the handle with your hands. To change completely manual starter to a mechanical, it may take about two hours of time.

Prevention will prevent repairs

There is another important point that is best to remember. New things at first work perfectly and starters. no exception. The factory starter is quite capable of starting a new uniform tractor from one jerk. And such an excellent state of affairs will last about the first year of operation. To avoid annoying troubles, follow whether there is enough lubrication, before each launch. Also measure the strength of a jerk when craving for a handle. This will help reduce the likelihood of a breakdown.

Elektrostarter for one.axle tractor

Motobobes are presented with an extremely common device that allows to significantly simplify the cultivation of land, as well as many other types of work. Having found out how to install a new starter on a single tractor, the farmer will be able to independently carry out the repair of the product by saving on the services of a specialist.

Starter device

When planning to find out how to assemble a starter on the walk.behind tractor, you need to familiarize yourself with the features of this element and its design in more detail. Motobobes provide for the presence of two such devices at once. the main and additional, which guarantees a successful engine start even in low temperatures.

John Deere tractor hard to start, too much compression for the starter to turn over

Studying the device of the starter of the walk.behind tractor, it is advisable to allocate several important nodes at once:

The design provides that a coil with a cord is mounted in the center of the unit housing. A large ring spring is placed along the axis of the product body, which is responsible for the return of the product to the original position during rotation.

The principle of operation of such an element is extremely simple and reliable. the user pulls the cord, as a result of which the coil is rotated. Thanks to this, the element gives momentum to the engine, which contributes to its confident start.

Types of mechanisms

Before finding out how to repair the starter with your own hands, as well as the most common malfunctions of this node, you need to familiarize yourself with the varieties of details. Their various types are presented on sale, which differ significantly in their technical characteristics and the principle of work.

The most popular are:

spring devices. a classic version, is characterized by ease of installation and efficiency when used;
Electronic models. provide for the presence of battery for a successful start of the engine, the power is determined by the battery charge;
A manual mechanism is a simple but less effective option that provides for the use of a special handle to start engine.

When planning to buy a manual starter for a walk.behind tractor or another variety, it should be noted that for most models of equipment, spring elements are perfect, since their energy will be enough to start the engine. advanced electronic devices require a charge at the battery, which cannot be used in the absence of access to the mains.

Installation of the starter on a single tractor

Despite the fact that even a beginner master can dismantle such an element, it is necessary to adhere to the instructions when installing it. This will avoid serious breakdowns that can lead to the failure of important elements of the walk.behind tract. I figure out how to put the starter on a single tractor, you should adhere to the simplest instructions:

Dismantle the air filter, flywheel, which will allow access to the desired details of the product.
Disconnect the protective casing, turn the screws for fasteners of the case, its flywheel, the veneer, which is located under it.
Install the generator, adhering to the connection scheme.
Place generator magnets inside the flywheel so that the holes of both elements coincide. Combine them with each other using fasteners.
Install the resulting design on the aggregate motor, fixing the flywheel veneer.
Mount the case, protective casing and air filter back.
Connect the wiring of the generator to the relay.
Connect the terminals of parts and batteries.

After that, you can try to launch a motor block engine. if everything was done correctly, it will successfully begin its work.

Possible malfunctions

Despite compliance with operation rules, starters, regardless of their type, periodically require repair. There are several typical malfunctions at once, with which the owners of the motor blocks are most often encountered. The following can be attributed to the following breakdowns:

Such malfunctions differ significantly, however, to eliminate them, it is enough to disassemble the knot and, after conducting a defect, replace damaged, worn out elements.

Repair

In order to successfully restore the operation of the unit, it is enough to adhere to a simple instructions that allows you to quickly and safely disassemble the starter to inspect its internal details. It provides for the following actions:

Wipe the puck in the central part of the device.
Dismantle the cover of the case, inspect the elements for breakage.
Most often it requires replacing the lace of the starter of the walk.behind tractor or the spring mechanism.
In the first case, it is enough to replace the cord with a new analogue, but in the second you will need to correctly install the element. I figure out how to refuel the spring into the starter of the walk.behind tractor, you need to pay attention to special hooks with which fastening is carried out.

The replacement of the spring is required only if the hooks were seriously damaged due to excessive wear of the metal and are not subject to restoration.

There are several varieties of starters that can be installed on modern motoblocks. In this case, the most popular option is a spring mechanism, characterized by simplicity and reliability. If desired, you can independently install or repair such an element.

starter, heavy, axle, tractor, your, hands

What other types of starters are suitable for a walk.behind tractor?

Each owner of motoblocks must understand that at first absolutely all starters function perfectly and can delight their owners with such a state of affairs for about a year. But without periodic lubrication of details, their verification and the commensurate power of a jerk, such joy will not last long. Take care of the starter and he will answer you with high performance and a long service life.

This model of the walk-behind tract is a novelty of the late 2014 of the beginning of 2015, it was made at a well-known and loved by many 23rd base, and is its improved continuation. The main differences of this unit are the emerging headlight and the system of an electric starter operating from the built.in battery. These innovations are designed to significantly increase the user’s comfort when working with this agricultural device. It is worth noting that the launch of the 4-stroke American engine of BriggSstatton I/C to 8 liters.With. It can occur not only with the help of an electric starter, but also in an old proven way from a manual starter, pulling the starting cable of the factory mechanism. Such an opportunity provides a choice for the end user and will not let the walk.behind tractor idle in cases of a saturated battery or any other force majeure.

Installation of the starter on a single tractor

Dismantle the air filter, flywheel, which will allow access to the desired details of the product.
Disconnect the protective casing, turn the screws for fasteners of the case, its flywheel, the veneer, which is located under it.
Install the generator, adhering to the connection scheme.
Place generator magnets inside the flywheel so that the holes of both elements coincide. Combine them with each other using fasteners.
Install the resulting design on the aggregate motor, fixing the flywheel veneer.
Mount the case, protective casing and air filter back.
Connect the wiring of the generator to the relay.
Connect the terminals of parts and batteries.

Starter model for a walk.behind tractor

After that, you can try to launch a motor block engine. if everything was done correctly, it will successfully begin its work.

How to put a starter on a single tractor. the right procedure

Remove the electric starter from the walk.behind tractor in order to further repair the broken mechanism even a beginner. However, with the reverse installation of the starter on the unit with their own hands, many beginner farmers, as a rule, have problems. Due to improper installation, the starter does not launch the engine engine even after several strong jerks. In order to prevent typical errors, you should study the algorithm for installing the starter on a single tractor in more detail.

The installation of the starter should be performed in this order:

First you need to remove the flywheel. this will be required to install and fix the crown on it. To dismantle the flywheel, you need to dismantle the air filter, which will give free access directly to the internal structure of the motor block available in the farm;
Then you need to remove the protective casing and unscrew the screws that attach the basket of the starter mechanism, the flywheel and its nut. The removal of the flywheel, as a rule, causes certain difficulties, and therefore many experts advise immediately before repairing the walk.behind tractor to purchase a removable key. As soon as the flywheel is dismantled, you should turn the veneer, which is immediately behind the flywheel;
After that, the generator should be installed. The wiring in it must be sat in a hole located in the metal wall of the engine. Then the generator will need to be fixed in a place on the wall of the motor;
Further inside the existing flywheel, it is necessary to install generator magnets. In this case, all available holes in the flywheel and generator must match. Both elements will need to be connected by fasteners, after which it will install the crown of the used motorcycle unit. Immediately before the installation of the crown, it must be heated with a ballest burner;
The assembled mechanism must be installed on the motor block, while screwing the nut and the vene of the flywheel;
Next, screw the starter basket, fix the casing and motionlessly install the standard air purification filter in the regular place;
Then you need to remove the plug and put the starter itself on the engine;
Next, you will need to connect the generator wiring to the charging relay;
At the final stage, starting terminals must be connected to the engine of the walk.behind tractor and start the unit.

It is not as difficult to install a starter on the uniform tractor in the household, as it seems at first glance. The most important thing is to be as attentive as possible and adhere to the correct assembly algorithm.

All of the listed methods of repairing the starter are suitable for owners of Neva walk.behind shoes, cascade and agro. The procedure for removing and reverse installation of the mechanism will be similar to agricultural machines of all listed manufacturers of technology.

Prevention

Select and install a starter. only half of the work. If you want the purchased part to work as long as possible, you need to pay close attention to care. New things always work well. For example, a factory starter needs only one jerk to start the engine. However, after a year of active use, the state of affairs will necessarily change. In order to prevent such problems, you need to constantly lubricate before starting. In addition, you need not to overdo it when craving for a handle, as this can cause mechanical breakdowns.

If Kikstarter failed, then the repair usually includes the update of the components that stopped working. For example, the replacement of the cord is made if it frayed, and you can season the spring from MB-1 only with problems with its work.

Thus, the starter is an indispensable detail that ensures the work of the motorcycle unit. In the process of choosing, you need to pay attention to the manufacturer, compatibility with the walk.behind tractor itself and a type of model. In addition, you need to pay attention to the constant care of the starter, which will avoid breakdowns and quick failure with active use.

See the video on the prevention of the starter’s work below.

It is forbidden to use any materials without our preliminary written consent.

Small nuances for repair

In order to determine a specific malfunction, you will need to disassemble the area of the walk.behind tractor in which the starter is mounted. In what order the repair should take place:

First you will need to arm the scheme from the manufacturer. It describes how and where all its details are attached to the motornote. You will also need a key with which you will unscrew and remove the nuts.
Then you need to disconnect the starter. It is better to photograph and write down everything regarding its fastening scheme. Otherwise you may not collect it back.
In the center of the drum you will see the puck that you need to unscrew. This is the upper washer. When you remove it, disassemble everything that you will find inside and check if there is any damage to any element.

Repair tricks

The principal electrical diagram of the starter. Repair of a hand starter most often is to correct the exposed places of springs or replace some details. Sometimes it happens that it is necessary to replace the starter cord for the starter. To check what has broken down in the end, you need to disassemble part of the walk.behind tractor where the starter is located.

First of all, we are armed with the scheme of our unit, which describes the fastening of all parts, as well as the key to removing nuts.
Disconnect the starter block, do not forget to remember what and how it was established before.
There will be a drum with a puck in the center that needs to be unscrewed. After the upper washer was removed, we analyze everything inside, and check the elements for damage.

The design of the branded starter of the walk.behind tractor.

If the cord breaks, it is simply changed to a new. There are two hooks at the ends of the ring large spring. If there is no one at one end, you need to heat the metal and bend it with a hook. If necessary, the ring spring can also be replaced.

With your own hands, you can both collect and make out everything, the main thing is to look at the instructions and circuit of the unit. Disassembling the starter of the motor block occurs for the most part equally for all models of this agricultural machinery. The only difference will be the number of tongues under the puck. from 1 to 2.

Chassis

A diesel engine with a driver, produced by personally suited pneumatic crusts with a diameter of up to 10 inches taken from written off agriculturals, motorizedosaurs. Sometimes they take from passenger cars if you need to increase the patency of home.made technology. And when operating a walk.behind tractor on heavy soils, they are replaced by iron (as they manifest themselves in business, you can watch on the video). But the choice of wheels remains you, focus on the type of work that you will carry out.

Engine [tractor] starter repair. diy fix

When creating a home.made motor.cultivator, instead of wheels, soilofires are installed for the possibility of duging and loosening the soil. Thanks to the use of such a soil, there is no tamping of the soil through which the motor.cultivator has recently passed.

In the manufacture of the axis of the Cultivator, the homemade is recommended to use a monolithic piece of steel. The welded pipe will not fit, as it may not withstand the load.

Do.it.yourself starter renovation

Despite the high quality and reliability of modern starters, some owners sometimes face the need to repair them. Most often, the breakdown of the mechanism is insignificant, which allows you to quickly eliminate the malfunction with your own hands. The procedure for dismantling and further repair of the mechanism is as follows:

The repair of the node should start by studying its scheme. If the design of the motor block provides an electric type starter, then before dismantling the mechanism you need to familiarize yourself with the location of its terminals;
Using the key from the kit of the walk.behind tractor, unscrew all the screws and nuts that hold the mechanism in the design of the walk.behind tractor;
If the dismantling of the node is carried out for the first time, we advise you to photograph the starter before finally remove the mechanism from the unit;
Next, unscrew the washer located in the central part of the drum body and carefully examine the internal parts for breakdowns;
All further actions depend on the malfunctions of the starter details. If the cord came out of the system. it was erased or torn, then to replace you will need to wind a new product, adhering to the marks on the drum body of the mechanism;
Another common breakdown is a spring malfunction, or rather, its antennae, the edges of which should be bent in the form of hooks. If the antennae broke off, then the edges of the spring will need to be heated, and bend them so that the spring can be hooked by the holes in the drum. In this case, the residual length of the spring is of great importance. make sure that the part does not stretch too much. If you find that the spring is very short, or it has already begun to rust, it is better to replace it entirely.

Before mounting the starter back to the uniform tractor, we advise you to first clean the space inside the unit structure. This will prevent garbage from getting into the motor, carburetor and on the spark plug.

How to replace or put a starter spring in place?

If everything turned out to be in order with the rope at the starter, the suspicion falls on the coil itself. It is driven by a strip spring rolled into a roll. To change the spring, certain steps should be taken.

Remove the starter from the lawn mower.
Remove the starter coil.
Unscrew the main bolt holding the pulley on the case.
Pull the exciting antennae and the spring, the strip spring is almost completely straightened or folded by rings of a larger diameter.
Hold it in advance.
Check if the spring is valid (there may be rusty stains, breaks, etc. D.). If the hooks at its ends are cut off, the new ones will not be bent. high.carbon steel breaks when trying to bend it. Weakened hooks are suitable for easy bending.
Make sure that an auxiliary (ordinary) spring with washers in place. These details protect the coil frame from the end of the main spring with the ends. If the washers and the spring are broken, but there are no new ones, do not screw the coil bolt hard, but follow it. it can unscrew and get lost.
If the main (flat) spring is damaged, insert the same new. Put the hook at the end of the spring in its place and bend it, inserting the turn behind the turn into the space where it should be and should be.

The rewinding of the spring is performed in a minute. Oknovka in this action is gained quickly.

How to replace or put a starter spring in place, watch in the next video.

How to put a starter on a single tractor. an algorithm in details

With the dismantling, disassembly and installation of a manual starter of the walk.behind tractor, there are no problems even in novice farmers. However, the assembly and installation of an electric steamer in inexperienced owners of motoblocks raises a number of questions. As a result of the incorrectly completed procedures, the engine launching mechanism refuses to work, which is why the starter has to be carried to the workshop. To avoid this need, we will study how to install a starter on a single tractor at home. The installation looks as follows:

To install and fix the crown on the flywheel of the walk.behind tractor, the flywheel will need to be removed. To do this, remove the aggregate air filter to get free access to the internal structure of the walk.behind tractor;
After that, remove the protective casing, unscrew the screws holding the basket of the manual starter, the flywheel nut and the flywheel itself. The dismantling of the flywheel of the starter’s starter can cause certain difficulties, therefore, to remove this part, it is better to purchase a special removable key in advance. After removing the flywheel, do not forget to unscrew the key located immediately behind him;
Next, you need to install the generator. In this case, stick its wires into the hole in the steel wall of the motor, and install the generator in the seats on the engine wall;
Then set the generator magnets into the flywheel so that the holes in both elements match. Connect both parts with screws and set the crown. Before that, the crown must be heated using a burner in the form of a spray can;
Install the assembled node back to the engine, simultaneously screwing the wraps and gaku tank;
Screw the basket of the manual starter, fix the casing and install the airblock air filter in place;
Next, remove the starter installation plug and install the starter itself on the one.axis tractor;
After that, connect the wires of the generator to the charging relay;
Connect the starter terminals to the aggregate accumulator and start the one.axle tractor.

As you can see, installing a starter to a walk.behind tractor is not so difficult as it might seem at first glance. The main thing when assembling with your own hands is to strictly comply with all the rules and recommendations listed in the algorithm.

Conclusion

You can independently understand the reason for the starter breakdown on your walk.behind tractor if it has a manual launch mechanism.

This type of node is quite easy to dismantle and disassemble. Over time, he loses his original characteristics and starts the motor only after 3 or 4 strong jerks. This means it’s time to replace it.

For some domestic motoblock models, there are special sets of modifications that allow you to install another type of starter on the unit. Unfortunately, they cannot be used on Chinese and American models.

Prevention will prevent repairs

Since the section is electrical equipment, I will start with the main one, this is the electric circuit of the uno-based tractor motor Sich MB-6.

Electric CHILD CHARTOME MOTOR SICH MB-6 (took from operating manuals)

Electric circuit Unoic tractor motor sicm mb.6 (took Victor from video)

Electric circuit of engine locking of the engine Unoic Tractor Motor Sich (took from the Victor video)

Electric circuit Unoic tractor motor SICH MB-6 (Victor video)

If there are any questions or additions, please do not be shy and write in Комментарии и мнения владельцев.

26 Комментарии и мнения владельцев

Provit Usm. In MB8 Z. I don’t want to picking to Garyachi. Having set the coil to the coil, Idalnoye, PIDKHRIT AND PIDAZHIT GINETER, BOOD CONCEPTING, VID CHOGOS PIDIDE

Vyacheslav, you can learn in more detail which ignition coil and how connected?

how much I measured and understood in MB 12V change. Does anyone have a bunch on MB 12V constant (that is, the transducer AC \ DC) ? I want constant 12V. Since the headlight plus is necessary for a constant for a constant for a sprayer (there the pump 12 volts requires, homemade). Well, I want to come out. to make dimensions on MB and trailer on diodes (Fari by the stature is also diode).

There was an attempt to buy AC \ DC stabilizers on Ali. for a long time, for something went wrong and they burned out, I abandoned the idea. But there is a Bosyatsky fit (gave the dimensions) and the question is again relevant

Yura, please tell me, the wires that go to the oil alarm alarm is no 12V there 2V.5V-3V, and in the shield the largest voltage is on a free connector about 6v. What to do.

Sergey Mamedov, why is there no 12V oil pressure on a control lamp 12V? The oil pressure sensor comes 12V?

Install a switch from Minsk. And if everything is in order of the spark with a pea with the generator. 12 V should only be if you turn on the load of at least 40 watts on idle voltage from 6 to 9 volts.With a load of 55 watts and a revolution of approximately 2500 about.min voltage 12-14 volts. White wire and mass resistance 180-200 Ohms. Red wire and weight 380-400 Ohms. if the indications vary greatly from these ignition will not work normally.

Victor, thank you hope this is useful to the owners of the motoblock motor

The starter for the walk.behind tractor is responsible for the start of the motor. With it, the engine is regularly and quickly starts. Many motoblocks work on manual starters. But it is possible to perform an independent replacement of a manual starter with an electric. To do this, follow a simple scheme. A simple algorithm will allow even a novice farmer to perform all installation work.

For good operation of the starter, it is necessary to regularly perform preventive work. Simple actions will allow you to keep the entire unit in good condition. The technique will last longer, working uninterruptedly.

Possible malfunctions

Such malfunctions differ significantly, however, to eliminate them, it is enough to disassemble the knot and, after conducting a defect, replace damaged, worn out elements.

Repair

Wipe the puck in the central part of the device.
Dismantle the cover of the case, inspect the elements for breakage.
Most often it requires replacing the lace of the starter of the walk.behind tractor or the spring mechanism.
In the first case, it is enough to replace the cord with a new analogue, but in the second you will need to correctly install the element. I figure out how to refuel the spring into the starter of the walk.behind tractor, you need to pay attention to special hooks with which fastening is carried out.

The replacement of the spring is required only if the hooks were seriously damaged due to excessive wear of the metal and are not subject to restoration.

What breaks most often?

The easiest way to fix what you can simply replace. For example, if you have a cord for a walk.behind tractor, then you can change it to a new. As for the large spring, everything is also simple here: study the places of its fastening. There are two hooks at its ends. If one of them is not, then it is worth heating the spring, bend its end in the form of a hook and it will again be ready to serve. However, if the hook broke due to fatal fatal, then it will be more advisable to replace the spring.

Sources:

https://stankoinstrumentiosnastka.ru/izmerenie/ruchnoj-starter-dlya-motobloka.html
https://mzoc.ru/selskohozyajstvennaya/kak-postavit-starter-na-motoblok.html
https://toolprokat43.ru/blog/samodelnyj-starter-na-motoblok.html
https://albamusicshop.ru/selhoz/kak-sobrat-starter-na-motobloke.html
https://technorama.ru/info-baza/kak-namotat-starter-na-motoblok.html
https://simsvarka.ru/pro-svarku/remont-startera-motobloka.html
https://evakuatorpodolsk.ru/v-selskom-hozyajstve/kak-sobrat-starter-na-motobloke.html
https://estetika-studia.ru/shema-elektrooborudovaniya-motobloka-so-starterom/
https://ats-sib.ru/motobloki/elektrostarter-dlya-motobloka-svoimi-rukami.html

Articles axle, hands, heavy, starter, tractor, your