Stihl trimmer stalls at idle

Why does the chainsaw stall when you press the gas

Let’s say the chainsaw works normally at idle, but when the gas is pressed sharply, it stalls. What could be the reason? It is immediately clear that this is not about the ignition (no spark), since if the ignition is faulty and there is no spark, the tool would simply not start. This means that the fuel system remains.

There are a lot of malfunctions of the fuel system and to determine the exact reason why the Stihl 180 chainsaw stalls when you press the gas, you need to carry out a complete diagnosis. We recommend reading about common malfunctions of the Stihl 180 chainsaw and their elimination.

Air filter

On the pages of the world wide web, you can find information that the Stihl 180 chainsaw can stall due to strong contamination of the air filter. I would like to refute this not entirely correct information, and report that the Stihl MC 180 carburetor is equipped with an expansion joint, which is designed and installed in order to take in the air necessary for the normal operation of the Stihl 180 chainsaw, bypassing the contaminated air filter. Of course, the power with a clogged air filter will drop a little, but it will definitely not stall. The power may also drop due to wear of the piston, here it will already be necessary to repair the piston Stihl MS 180 chainsaw.

stihl, trimmer, stalls, idle

Why stalls at idle

The first and most common cause of this malfunction is improper carburetor adjustment. You can adjust the idle speed yourself, for this you need to have a Stihl adjusting screwdriver, which is supplied with the unit. The adjustment hole is located on the right side of the Stihl 180 saw on the handle and is marked with “-” and “”.

If the Stihl chainsaw does not keep the speed and stalls at idle speed, you can be almost 90% sure that it has irregularities in the fuel pump operation system, as a rule, it is air leaks into the crankcase through the oil pan gasket, or, much more often, through the oil seals crankshaft. Air leaks reduce or completely stop the impulse that is supplied through special channels to the fuel pump of the chainsaw. As a result, the Stihl 180 chainsaw does not receive the required amount of fuel and stalls at idle speed.

Diagnostics can be carried out using a special device called a vacuum gauge.

The second way to check the performance of the oil seals is to pour gasoline into the engine crankcase and look at them, if the oil seals pass gasoline, it means they cannot provide normal pressure in the crankcase, which will make idle work impossible. And when operating at high speeds, with leaking oil seals, there is a possibility of seizure of the crankshaft bearings.

The algorithm for checking the crankcase and Stihl 180 oil seals for leaks is as follows:

  • The top cover is removed.
  • Dismantle the air filter housing and carburetor.
  • The handle of the chainsaw is removed.
  • The starter spins and retracts.
  • On the side opposite to the starter, the side cover and the drive sprocket are removed.
  • A piston stopper is installed in the spark plug hole or a string from an old starter with knots imposed on it is stuffed into the cylinder.
  • The flywheel and clutch are unscrewed, after which the parts are removed. It is worth knowing that the chainsaw clutch has a left-hand thread and unscrews clockwise.
  • The gear wheel of the drive of the oil pump is removed.

Having disassembled the Stihl MS 180 chainsaw, you can see the oil seals, then you need to fill the crankcase with gasoline and check the leakage. It is possible to fill the crankcase through the fuel window in the cylinder; for this, the piston must be raised as high as possible. If leaks are found, it is necessary to replace the defective oil seals, or re-seal the pallet. You can collect Stihl 180 following the reverse sequence of the algorithm.

Carburetor

One of the reasons why the chainsaw does not develop speed when you press the gas, but rather stall, is a malfunction of the carburetor. Let’s say the Stihl 180 saw worked properly, and then it was put on for a long time and did not use it. After it was started, and at idle, it works well, and when you press the gas, it can stall. Why stalls? The reason is a sticky carburetor injector valve. Of course, this is not 100%, but the probability of such a malfunction is high. We recommend reading an article about the device and repair of the Stihl 180 carburetor.

In order to check the injector, it is necessary to remove the carburetor and disassemble it. To remove, it is necessary to unscrew the two nuts securing the air filter and the carburetor, then remove the air filter and the engine control lever, while disconnecting the choke control rod from the carburetor. Next, you need to slightly pull the carburetor towards you, and disconnect the fuel supply hose.

It is necessary to remove the fuel hose as carefully as possible, and prepare a plug for it in advance, since fuel should come from it.

Having removed the carburetor, it must be blown out and cleaned of dirt, only after that the carburetor can be unscrewed.

It is necessary to unscrew the cover of the main chamber of the carburetor, this is the one on which the compensator is installed on top. Further, using a bolt of 8 mm and a length of at least 50 mm. Knock out the valve.

It is necessary to knock out the valve by installing the carburetor on a wooden stand, this will ensure its protection from damage to the body.

After the nozzle is removed, you can blow it out with a compressor. The valve should only let air through in one direction, if the valve can be freely blown in both directions, then it is defective and must be replaced with a new one. Collect the chainsaw after the valve is repaired, it is necessary to follow the reverse sequence of disassembly.

You can clearly see how the carburetor is being repaired, or rather, how to properly knock out the nozzle valve from the carburetor body by watching the video.

Another common reason a saw can stall when revving up is air leaks into the carburetor. It is possible to check this only with a special tool, but it is worth noting that if preventive work on the carburetor has not been carried out for a long time, then a new set of gaskets can be installed in the carburetor. In some cases, this helps to solve the problem with its depressurization.

When disassembling the carburetor to replace the gaskets, you need to carefully inspect its needle valve, press the rocker arm and check its lifting. Sometimes, especially after the Stihl chainsaw has stood for a long time with fuel in the carburetor, the needle may burn to the carburetor body and not perform its functions. Simply put, the needle valve will not allow the fuel mixture to pass through. In this case, the saw will not work.

Filter check

The first thing to check is the fuel filter.

In some cases, a filter clogged with dirt is unable to pass enough fuel mixture through it. Accordingly, a fuel shortage arises in the system, which leads to the fact that when you press the gas of the chainsaw, the fuel burns out, and the new one does not have time to enter, as a result of which the Stihl chainsaw stalls. Also, with a clogged fuel filter, there may be a noticeable drop in the power of the chainsaw at maximum speed, but this is with insignificant contamination.

Why stalls at full speed

Very often you can hear the question why the chainsaw stalls at full speed. There may be several reasons. First, you need to consider how the saw stalled. Suppose the tool worked fine and suddenly, for no apparent reason, it suddenly stalled and the starter did not turn. In such a situation, you can be 100% sure that the chainsaw is jammed and you need to start its overhaul.

The second situation is when the Stihl 180 chainsaw worked normally, then gradually lost power in a short time and stalled, while the cylinder overheated. In this case, most likely the reason is air leaks under the rubber pipe connecting the carburetor to the cylinder or its rupture. The mixture was depleted, resulting in overheating. You can eliminate the cause by changing the pipe.

For what reasons Stihl 180 stalls at idle or full throttle

Any tool can break and the Stihl MS 180 chainsaw is no exception. Today we will try to understand such issues as: why the chainsaw stalls when the speed increases, also at idle and at full speed. Consider the options for diagnosing and eliminating malfunctions associated with this behavior of the Stihl 180 chainsaw.

  • Why does the chainsaw stall when you press the gas
  • Filter check
  • Air filter
  • Carburetor
  • Why stalls at idle
  • Why stalls at full speed
  • Output

If the Stihl chainsaw does not keep the speed and stalls at idle speed, you can be almost 90% sure that it has irregularities in the fuel pump operation system, as a rule, it is air leaks into the crankcase through the oil pan gasket, or, much more often, through the oil seals crankshaft. Air leaks reduce or completely stop the impulse that is supplied through special channels to the fuel pump of the chainsaw. As a result, the Stihl 180 chainsaw does not receive the required amount of fuel and stalls at idle speed.

Diagnostics can be carried out using a special device called a vacuum gauge.

The second way to check the performance of the oil seals is to pour gasoline into the engine crankcase and look at them, if the oil seals pass gasoline, it means they cannot provide normal pressure in the crankcase, which will make idle work impossible. And when operating at high speeds, with leaking oil seals, there is a possibility of seizure of the crankshaft bearings.

The algorithm for checking the crankcase and Stihl 180 oil seals for leaks is as follows:

  • The top cover is removed.
  • Dismantle the air filter housing and carburetor.
  • The handle of the chainsaw is removed.
  • The starter spins and retracts.
  • On the side opposite to the starter, the side cover and the drive sprocket are removed.
  • A piston stopper is installed in the spark plug hole or a string from an old starter with knots imposed on it is stuffed into the cylinder.
  • The flywheel and clutch are unscrewed, after which the parts are removed. It is worth knowing that the chainsaw clutch has a left-hand thread and unscrews clockwise.
  • The gear wheel of the drive of the oil pump is removed.

Having disassembled the Stihl MS 180 chainsaw, you can see the oil seals, then you need to fill the crankcase with gasoline and check the leakage. It is possible to fill the crankcase through the fuel window in the cylinder; for this, the piston must be raised as high as possible. If leaks are found, it is necessary to replace the defective oil seals, or re-seal the pallet. You can collect Stihl 180 following the reverse sequence of the algorithm.

If the Stihl MC 180 chainsaw stalls at idle, does not gain power when you press the gas, or even stalls at full speed, it is necessary to diagnose the fuel system and check the crankcase for leaks. You can do it yourself, but you need to have certain skills. If you are not familiar with two-stroke saws, it is better to turn to specialists, since this technique is rather capricious and any mistakes are expensive.

Why the lawn mower stalls | lawn mower | trimmer when pressing the gas, at idle, on hot

Why the lawn mower stalls when you press the gas: reasons and solutions. The lawn mower stalls (trimmer):. at idle.

  • failure of the idle sensor;
  • clogged throttle;
  • malfunction of the throttle position sensor;
  • dirty injector or carburetor

The grounds for a breakdown can be completely different, therefore, when eliminating them, you will have to operate with all sorts of actions and techniques. If you have a considerable driving experience behind you, and you know the features of the car like the back of your hand, regardless of the model, then troubleshooting this kind of problem will not give you any problems. And all because such breakdowns are not difficult or serious. It follows that you can get the car working without any help. Well, if the level of awareness or lack of free time does not give you the opportunity to eliminate all defects on your own, it is better to seek help from knowledgeable people who can save you from unpleasant moments as soon as possible.

Similar posts

Video. fixing the problem on a car with a carburetor:

When the air damper is opened

It happens that the unit stalls when the air damper is opened, normally idling. This is due to air leaks in the system, caused by cracks in the fuel hose or problems with the oil seals. The carburetor metering system may also malfunction, and the lawn mower will stop after opening the damper.

Fuel hose in carburetor

All the possible reasons that the lawn mower stalls, and how to fix them, are contained in the following video.

There are many reasons for stopping lawn mowers, but the most common malfunctions associated with its carburetor. They can occur in any case. The most problematic option is when a serious breakdown occurs, and you need to purchase new parts or change the lawn mower.

In order for the trimmer to work normally for a long time, you must strictly follow the instructions for use. It is necessary to fill the unit with a suitable fuel mixture, the unit should operate at moderate load.

Idle ones do not work

At idle speed

At idle, common reasons for stopping the trimmer are as follows:

  • contamination, misalignment or incorrectly adjusted carburetor adjustment;
  • clogged air filter;

Replacing the air filter for lawn mowers

Trimmer air filter

  • reducing the speed of the gearbox when it heats up, which is a consequence of the use of an unsuitable fuel mixture;
  • clogged throttle;
  • air entering the system;
  • not enough fuel to operate the lawn mowers.

If the problem area is the carburetor, then the equipment will stop at both “cold” and “hot” start.

Chinese lawn mower NO IDLE.PROVISION OF CARBURETOR ADAPTER / BC330 repair

When it’s hard to start a lawn mower, it is worth paying little attention to the fastening of the carburetor, adapter and their seals

Correct Way To Adjust Or Tune The Carburetor On A Weedeater / Grass Trimmer. Video

Vibrations that occur during the operation of the lawn mowers can lead to misalignment.

Incorrect adjustment of lawn mowers can be corrected simply by adjusting it in accordance with the requirements specified in the instruction manual.

In addition, sometimes gasoline trimmers can stall due to the fact that the valve located in the gas tank cap is simply clogged or stuck.

To find out, try using a scythe by loosening the gas cap.

If the device works properly in this mode, clean the valve.

Stihl trimmer won’t stay running. Sad ending

over, the lawn mower can stall due to poor fuel flow to the carburetor.

Why, then, does the device start, you ask?

The reason for this is that at first the fuel gradually runs into the carburetor and it is enough to work at increased power.

However, then it is produced and at high speeds the engine starts to stall.

As for the carburetor, the problem here may also be that its body is too tight.

The reason that the lawn mower stalls at high rpm on gas may also be air leaks.

This is the possible presence of a place through which air can pass during the heating of the engine.

Be sure to check the fuel inlet hose, among other things. For some reason, it is somewhere from 5 times, at idle it works and the trimmer stern ggt950b does not rotate. The problem may be that it does not hold well or is cracked altogether.

These are the main reasons why