Storage of STIHL saw for the winter. How to start a saw after prolonged downtime

How to store an Eletric STIHL braid

After the spring-autocosa, it is time to prepare it for winter storage, so that after winter it again successfully continues to work, then before storage it is worth taking into account some tips.

Here we have collected for you several valuable care tips:

Before storage, it is necessary to thoroughly clean the motorcycle (electrocos) of the remnants of dust, garbage and residues of mowed grass. Check whether all fasteners and fasteners are tightened.

Enough the fuel tank

Alt = “Identify the fuel tank” width = “” height = “” /completely empty the fuel tank and develop the remaining fuel that remained in the carburetor (to deviate the carburetor, you need to work with a motorcycle at idle until the engine stops). Check the device for the lack of pollution and, if necessary, let it dry. Check the technical condition and, if necessary, rinse the fuel filter in the fuel.

Check the spark plug

alt = “Check the spark plug” width = “” Height = “” /Take the candle and inspect it. If the spark plug has “reddish” electrodes, then it is in order. If the spark plug looks different, then it must be cleaned or replaced. It is also recommended to check the brightness of the sparks issued candles. To do this, we put on the candle the supra.light, and the lower part is in contact with the cylinder and, pulling behind the starting cable (note that the lever does not stand in the Stop (0) position, we observe the color of the spark. The working color of the spark is bright blue! If there is an orange, red or different from the required, then it is necessary to check the probe between the central and lateral electrodes (if necessary, reduce the gap or increase).

After checking the spark plug, take a 10 ml syringe and add such a volume of motor oil to the combustion chamber (to the cylinder). Then several times you need to pull the trigger cable so that the piston with rings evenly produces the oil on the walls of the cylinder.

Check the starting device for the presence of a creak. The appearance of a creak may indicate an abrasive hit between the turns of the return spring (located under the cable pulley). To eliminate, you need to remove the pulley and the return spring, then wipe these parts and places where they are installed well.

Check the metal tool

alt = “Check the metal tool” width = “” Height = “” /Remove the metal knife and clean it. Also check for the lack of damage (cracks, chips) and apply anti.corrosion protection. If necessary, you can give your metal knives to the specialized “service center” of the KHK company for sharpening and balancing.

Keep the cutting thread in a wet place

alt = “Store the cutting thread in the wet place” width = “” Height = “” /To preserve the cutting plastic string of elastic, take out the coil with a string from the cutting head and store it in a wet place. Two to three days before the start of the new season, put the string in the water-this will remain its flexibility and elasticity (this also applies to the knives of the trimmer head Stihl Polycut 6-3).

Saving space in suspended

Alt = “Saving a place in an limit state” width = “” Height = ” /It is best to store motorcycles in limbo. to save space you can fold the mandate braid for grass.

The entire lineup of the production of STIHL is presented in the “catalog” of the site. You can buy a motorcycle (trimmer for grass) in specialized stores of KHK at the price of a manufacturer. Quality certificates, guarantees are provided, service and repair are carried out. You can always get a free professional consultation on the operation and storage of tools from the company’s managers.

How to prepare a chainsaw for winter storage. Storage tips in winter in winter

With the onset of cold weather, many owners of the chainsaws simply send saw equipment to the shelf in the garage, until better times. At the same time, few newcomers know that the proper storage of a chainsaw in winter involves the conservation of equipment using special technology.

There is a special series of chainsaws that have admission to work in winter cold. Such models have a well.insulated case, as well as a carburetor heating system.

With prolonged storage of chain saw technology, a complete stop of the actual mechanisms occurs, which leads to the following negative consequences:

• Friction vapors and other nodes cease to get a lubricant, which leads to their drying out.
• The old lubricant turns into a thick jelly, which over time dries and tanks.
• Seals spoils, as well as filtering elements.
• The fuel is exhausted and loses its conditional properties.

In many cases, the owners of the chainsaws have to be perplexed that the chainsaws worked properly in the fall, and in the spring he flatly refuses to start to start. All the fault of the incorrect storage of a chainsaw in winter, during the cold season of the year.

General rules for conservation of technology

Any tool, regardless of the type and purpose, before laying on storage, you need to wash, dry and inspect the details for wear and replacement. There is nothing worse than moisture that fell into mobile or vulnerable details and mechanisms. Freezing in an unheated room, it turns into ice and damages the elements of the system. It is also advisable to drain gas tank gasoline for fire safety reasons. But for the clock, other recommendations. the equipment cannot be left “dry”, so the oil is not removed for the winter, but they are changed.

When stored, fold the equipment as indicated in the operating manual

The cutting parts (such as lawnmand knives) should be sharpened, and hinged joints should be cleaned of dust and dirt and grease. Check the condition of the fasteners and power cord of the power tool, if necessary, replace them without leaving until spring. Next, we consider each type of technique and the requirements for its conservation in more detail.

Optimal solution

For winter work, it is better to buy a chainsaw, specially provided for a total. There is a technique equipped with a hot air supply system to a carburetor from the cylinder cooling ribs. This reduces the risk of freezing of the air filter and prevents the formation of condensate on the carburetor. Many manufacturers (Makita, Stihl, Maruama) produce models in which you can switch the “winter” and “summer” modes using a special damper located in the lid. Since in winter mode the carburetor will be produced in advance heated air, icing is impossible.

Drain the remaining gasoline from the tank, drain the oil from the tire (lubrication of the tire and chain). Remove the shinkus of the saw, clean everything, wipe it, that’s perhaps all the conservation

Severstal was one of the first participants in the WorldSteel global program to reduce greenhouse gas emissions

Typically, chainsaws are used only in the warm season. Starting in the fall, their test check should be carried out, having determined whether the tool for maintenance needs. And if the chainsaws of Husqvarna for which are now quite affordable, you are in good condition, then it’s time to prepare them for the winter. The required procedures, of course, are noticeably different from intended for a conventional saw or shovel.

How to store a chainsaw in winter

This is perhaps one of the few tools for which there is work in the cold season. True, the range of operating temperatures of the chainsaw is usually small due to the fact that it contains insistent parts, gas and oil. If the manufacturer guarantees the operation of the tool at a temperature of –10 ° C is a very good indicator, and such a saw can be used almost all year round. If you leave the summer cottage for a long time, then take care of proper conservation.

The “heart” of any chainsaw is a single.cylinder two.stroke carburetor engine. Another important element is the chain. It is the care of these two elements that most of the recommendations for conservation are devoted to:

• First of all, drain the remains of fuel from the tank, carburetor and oil for lubrication of the chain. For full production of fuel, you can start the chainsaw of an idle and wait until the gasoline is over. After that, wipe the gas tank dry so that it does not begin to rust. This is an option for prolonged conservation, at least 3 months. But there is a second option for those who are falling the forest or carrying out other works in winter. In this case, the tank is advised to fill with high.quality gasoline to the edges and leave for storage in this state. If you urgently need to cut down a tree. excellent, you have a completely finished technique at hand. But remember, gasoline, which after 2-3 frosty winter weeks in consistency will begin to resemble jelly, can even be disable; even a first-class motor;
• Using a wire probe or homemade nozzle, remove filter-endor filters from the fuel and oil tanks. Rinse them and set them back after drying or, if necessary, replace with new. Do the same with an air filter;
• Remove the saw chain and tire and clean them of the remains of sawdust, wood and dirt;
• Remove the clutch cover, thoroughly rinse it under a stream of warm water and let it dry. Lubricate the worm gear and screw of the side tension system of the chain;
• Remove the spark plug and clean it from soot and fuel residues. Pour 5-7 ml of motor oil into the candle hole and cranceize the engine for 3-4 revolutions so that the oil is distributed according to the connecting rod mechanisms and the cylinder-piston group. Leave the piston at the top (in the raised state). After that, set the candle in place, but do not put on the ignition terminal;
• Cover the saw tire and chain with protective lubricant and store wrapped in a piece of paper or fabric impregnated with oil;
• pack the tool and hide the removed parts into a dry, dark and nonsense place.

How to start a chainsaw after a long downtime

In order to start the Stihl 180 chainsaw for cold, it is necessary to observe the algorithm indicated by the manufacturer in the instructions for the Stihl 180 chainsaw, namely:

• Turn on the ignition and install the engine control lever in the lowest position (in this position, the airburator of the STIHL 180 carburetor cloth overlaps the air from the air filter, and the throttle is completely open, so the fuel mixture is enriched);
• Pull the starter handle several times, until the first outbreak is passing (the flash signals that the fuel mixture entered the cylinder and the saw was ready to start);
• Set the control lever to one position upward from the fully lowered (in this position the air damper opens, and the throttle remains in the same position as before);
• Pull the starter and start. The saw will start and work at increased speeds, due to the fact that the throttle is open as possible. To install the damper in the idle mode, you need to press the gas trigger and immediately release, the tool immediately normalizes the momentum.

On the Stihl MS 180 chainsaw, any additional devices are not installed in the standard configuration capable of facilitating launch.

Below you can see how to get Stihl 180. The video reflects in detail all the main points, and the author’s Комментарии и мнения владельцев allow you to understand the whole process to the smallest detail.

Briefly about the starting device

A chainsaw works on an internal combustion engine. This is a simple device, the design of which has no special bells. It usually works properly even in difficult conditions for this.

The functioning is provided by structural elements:

• Carburetor engine (see. Carburetor adjustment).
• Clipers of centrifugal type clutch.
• Ignition system, in almost all devices contactless.
• Carburetor that adds air to the fuel mixture.
• Fuel system. Its standard device consists of a hose, filter and gas tank, but sometimes it also has additional details.
• Starter.
• Tire.
• Chain (see. Oil for the chain).
• Tension mechanism and circuit brake (see. how to sharpen a chain).

How to start a chainsaw: instructions for the saw “STIHL”

Almost every person living in a private house or having a country site from time to time uses a chainsaw working on a gasoline internal combustion engine. Beginners often have the question of how to start a chainsaw correctly. It is worth noting that professional, semi.professional and domestic tools are starting approximately the same. How exactly to do this will be told in the material.

• Features of the launch of the tool
• Launch according to the instructions
• Maintenance of the tool
• Starting without a starter
• The reasons why the chainsaw is not started

Safety precautions when working with a chainsaw

During the operation of the chain gasoline saw, its owner must carefully comply with the safety regulations.

• Work with tools only in protective glasses, gloves and a suit of dense fabric. In addition, the operator should wear shoes with an anti.slip sole;
• use a chainsaw only in the fresh air or in a well.ventilated room. The tool engine produces toxic gases that can harm the health of the operator and others;
• During sawing small branches and logs, use a special stand called “goat”. It should be installed on a flat stable surface;
• When using a saw at a height, use safety cables. The operator must constantly ensure that the cut off the branches do not touch power lines;
• Before cutting large trees, clear the place for the operator’s departure in advance. In this case, it is necessary to determine in advance the direction of the fall of the barrel and move in time in the opposite direction.

No matter what purpose the chainsaws were used for, the operator must hold it tightly with both hands. Otherwise, the tool can slip and cause irreparable harm to the health of its owner or others.

Start Stihl MS 180 C

The device of this model, in comparison with the previous one, has some differences in the starting mechanism, but it does not bear any changes to the launch algorithm. The fact is that the Ergostart system is installed in STIHL 180 C, which, due to the additional spring installed in the chainsaw starter, reduces the engine resistance during starting.

How to saw correctly: tips and recommendations

In the video lessons presented, you can familiarize yourself with the methods of working with a chainsaw in different situations, learn not only to harvest firewood for the winter, but to saw logs on boards, cut off other materials, saw the ice with a chainsaw, saw a log along.

Adjustment of the carburetor of the chainsaw STIHL

It is carried out if the saw stalls when you press the gas. Previously, the carburetor is cleaned of pollution, change the candle in it and the filter is cleaned. Regulate the work at idle.

Settress Carburetor STIHL Carburetor

• First you need to turn off the tool and turn the two screws to the stop. l and h.
• The same bunches are turned into one revolution.
• Start a tool, warm up the motor.
• Squeeze the gas lever and turn the screw h until the speed is stabilized.
• Turn the screw La until the movement of the saw chain starts, after which I turn it on a quarter in the opposite direction.

After these manipulations saw, the gasoline chain STIHL should start working. If the problems remain, you need to work with the La screw and scroll it a little more.

Selection of components for the mixture

The basis for our mixture will be gasoline. You need to take an oil product, the octane number of which is more than 90. Do not save and take dubious fuel, then you will pay more for repairs. Additives that increase the octane number is also a dubious choice.

How to get a chainsaw

The chainsaw is always held with both hands, tightly squeezing the hilt with all the fingers (the thumb of the left hand should be located under the front handle). Put the saw closer to the body. so the hands of the hands will be less tired (you do not need to be afraid of the proximity of the saw). In addition, in this position it will be easier to maintain balance and maintain full control over the process.

The legs must be placed widely, bending at the knees for stability, but the back should be kept even. If the master needs to change the situation, he must first turn off the engine by activating the brake. If you need to move the chainsaws a considerable distance, it is recommended to cover the bus with a casing.

Learning to use a chainsaw at first is better on horizontal, not too thick logs. When confidence and strength in your hands is felt, you can learn a roll of trees. To cut logs or bars evenly, you need to make marks with a pencil and then gradually move along these marks. Well, if there is an opportunity to see how experienced sawers work.

The stage of preparation

Before cutting down the tree, it is worth making sure that the surrounding objects (railway rails, buildings, power lines, vehicles and so on) will not suffer as a result of the fall of the trunk). There should not be anything superfluous at a distance of two lengths of the sawn tree in any direction. In addition, if the place is crowded, then it is necessary to use warning signs. this is a prerequisite.

It ultimately depends on this in which direction the barrel will fall. Especially careful should be with a rotten, dry tree. It can lead itself unpredictable for the lumberjack and fall not as planned. You can determine the damaged tree by external signs (dry branches, damaged barrel). Experienced rollers determine the quality of wood tapping on the barrel. a healthy tree “rings”, the patient has a deaf sound or is not heard.

The earth around the tree must be cleaned of bushes and other overgrows. this is another important preparatory action. It is necessary to remove everything that can interfere with the safe departure of the master with a chainsaw during the roll

How to saw

The treatment procedure itself usually occurs in this way. The lumberjack rises to the right of the barrel and makes the guide ahead on the side of the natural tilt at a 45-degree angle to a depth of about a quarter of the diameter of the tree. This file should be as low as possible. it will be easier to tie the barrel (and the stump will not be too high). It is also worth it to keep in mind that it fed as it indicates in which direction the tree will subsequently fall to the ground.

A horizontal cut is made on the opposite side of the tree after this. the main gross drinking. There should be some short distance between him and the inclined sawing file. this gap is needed so that the tree does not collapse before the term.

In the course of work, it is necessary to track where the barrel rolls in order to have time to react if something goes wrong. When the tree begins to fall, you need to quickly remove the chainsaw from the cut, turn off the motor and leave a dangerous place.

If, hooking with a roll after another trunk, the tree did not fall to the end, then professional assistance will be required. Leave it unattended, as well as to independently try to rectify the situation, it is forbidden to.

There are times when the tire of the chainsaw is stuck in the trunk. No need to panic and tear it out sharply, especially if the tool is in working condition. First of all, you need to stop the engine. And then you should manually tilt the barrel a little until the chainsaw is slipped.

You can read a detailed description of the video on how to properly start a chainsaw. Using this detailed instruction, you can get skills in working with a chainsaw.

What to do if the chainsaw does not start?

But what to do when all the actions specified in the operating instructions are completed, but the chainsaw is still not starting? Regardless of the manufacturer of chainsaws. Stihl, Husqvarna, Partner, Ural, Friendship. There are a number of common measures for factory tools.

Below are practical tips from professionals who were tested in practice and proved their effectiveness:

• Do not be nervous, do not try to adjust the mature carburetor.
• Put the tool aside and let it relax. The reason may be just that the candles are flooded. Let them dry.
• Get the instruction manual. Try to start the saw again. The saw brake does not need to be activated.
• If this does not help, try to remove the lid from the chainsaw housing and remove the air filter. Thus, you can check the cleanliness of the filter and at the same time facilitate the launch process.
• Replace the spark plugs. If it is impossible to install new candles, you can use the old ones, having previously removed and burned them.
• If there is an extraneous pungent smell, this means that the excess fuel hit the chainsaw engine. To fix this situation, you need to remove the candle and, turning the saw upside down, drain the excess. Without returning the saw to normal, pull the starter several times sharply. This will ensure the release of combustion products from the camera. Wipe the candle dry and bake it, then screw it up and start it without installing the filter.
• Check the surface of the piston for the presence of fuel. If you unscrew the spark plug and notice that it has dried through the hole, you need to enter a little fuel into the chamber with a syringe. The reason for the problems in this case may be a lock that prevents the fuel from entering the engine. If the engine can be launched using a small amount of fuel, the thrust will eliminate clogging, and the problem will be solved.
• The last two steps can only be performed with a dry candle.
• Check the starter for serviceability. It is impossible to start a chainsaw without a starter.
• Check the ignition ignition.
• Try to carefully remove the device muffler and run it without it.

How to do something yourself, with your own hands-a site of a home master

An excellent tool for masters and needlework and everything for the garden, at home and cottage literally for nothing. see for yourself. There are reviews.

In order not to encounter in the spring that the chainsaw does not work, come to her conservation responsibly. The implementation of simple rules will ensure reliable operation and extend the life of the tool if the shovels, rakes and traps on the winter are carefully cleaned from the ground, dry and hide in a dry place, then this is not enough with complex technical garden equipment. it needs appropriate care. In addition, nodes, components, fuel mixture and lubrication for long.term storage in the sub.pins are not calculated.

How to store a chainsaw in winter

This is perhaps one of the few tools for which there is work in the cold season. True, the range of operating temperatures of the chainsaw is usually small due to the fact that it contains insistent parts, gas and oil. If the manufacturer guarantees the operation of the tool at a temperature of –10 ° C is a very good indicator, and such a saw can be used almost all year round. If you leave the summer cottage for a long time, then take care of proper conservation.

The “heart” of any chainsaw is a single.cylinder two.stroke carburetor engine. Another important element is the chain. It is the care of these two elements that most of the recommendations for conservation are devoted to:

• First of all, drain the remains of fuel from the tank, carburetor and oil for lubrication of the chain. For full production of fuel, you can start the chainsaw of an idle and wait until the gasoline is over. After that, wipe the gas tank dry so that it does not begin to rust. This is an option for prolonged conservation, at least 3 months. But there is a second option for those who are falling the forest or carrying out other works in winter. In this case, the tank is advised to fill with high.quality gasoline to the edges and leave for storage in this state. If you urgently need to cut down a tree. excellent, you have a completely finished technique at hand. But remember, gasoline, which after 2-3 frosty winter weeks in consistency will begin to resemble jelly, can even be disable; even a first-class motor;
• Using a wire probe or homemade nozzle, remove filter-endor filters from the fuel and oil tanks. Rinse them and set them back after drying or, if necessary, replace with new. Do the same with an air filter;
• Remove the saw chain and tire and clean them of the remains of sawdust, wood and dirt;
• Remove the clutch cover, thoroughly rinse it under a stream of warm water and let it dry. Lubricate the worm gear and screw of the side tension system of the chain;
• Remove the spark plug and clean it from soot and fuel residues. Pour 5-7 ml of motor oil into the candle hole and cranceize the engine for 3-4 revolutions so that the oil is distributed according to the connecting rod mechanisms and the cylinder-piston group. Leave the piston at the top (in the raised state). After that, set the candle in place, but do not put on the ignition terminal;
• Cover the saw tire and chain with protective lubricant and store wrapped in a piece of paper or fabric impregnated with oil;
• pack the tool and hide the removed parts into a dry, dark and nonsense place.

About once a month, perform the crankshaft to update the lubricant on the connecting rods and in the cylinders with the pistons.

If you have an electric drain, then all you need to conservation is to lubricate the saw tire and chain with protective grease.

Where to store: options and necessary conditions

Sarai or equipped housekeeping block is on the house territory of almost every summer resident. These storage places are the most common. The main conditions for storage of gas technicics in sheds or utility rooms are low humidity and stable temperature without sharp jumps.If the room is insulated, it will be an additional plus.

Another place for storing benzotechnics is a garage. Do not place the equipment close to the car, and also, by suspending it, you need to make sure that in the event of a fall it will not touch the car.

This method is not very popular in the countries of the post.Soviet space. But if there are no other options, find the company that provides these services is possible.

What you should pay attention to:

General rules for conservation of technology

At least a tool, regardless of the type and purpose, before laying on storage, it is necessary to wash, dry and look around the details for wear and substitution. There is nothing worse than the water that fell into mobile or vulnerable details and mechanisms. Freezing in an unheated room, it is converted into ice and damages the elements of the system. It is better to drain gas tank gasoline from fire safety judgments. But other tips are closed. the equipment cannot be left “dry”, because the oil is not removed for the winter, but they are changed.

When stored, fold the equipment because it is indicated in the operating manual

The cutting parts (such as lactes of the lawn mower) should be sharpened, and hinged joints should be cleaned of dust and dirt and grease. Check the condition of the fasteners and power cord of the power tool, as needed, change them without leaving until spring. Next, we see each type of technique and the requirements for its conservation in more detail.

This is perhaps one of the few tools for which there is work in the cool season. True, the spectrum of operating temperatures of the chainsaw is usually small due to the fact that it contains insistent parts, gas and oil. If the manufacturer guarantees the operation of the tool at a temperature of –10 ° C is a very good indicator, and such a saw can be used almost all year round. If you leave the summer cottage forever, then patting the appropriate conservation.

“Header” at least some chainsaw is a single.cylinder two.stroke carburetor engine. Another principle element is a chain. Specifically, most of the conservation tips are devoted to the care of these 2 elements:

• First drain the remnants of fuel from the tank, carburetor and oil for lubrication of the chain. For the full production of fuel, you can start the chainsaw of an idle and wait until the gasoline is completed. Then wipe the gas tank dry so that he does not start rusting. This is an option for long.term conservation, at least 3 months. But there is also the 2nd option for those who are falling the forest or carrying out other work in winter. In this case, the tank is recommended to be filled with high.quality gasoline to the edges and leave for storage in this state. If you urgently come in handy for you to cut down a tree. excellent, you have a completely finished technique under your hand. But remember, gasoline, which after 2-3 frosty winter weeks will begin to remember the jelly by the mixture, even a high-class motor can disable;
• Using a wire probe or a home-made nozzle, remove filter-endor filters from the fuel and oil tanks. Wash them and set them back after drying or, if necessary, change to new. Do the same with an air filter;
• Remove the saw chain and tire and clean them of the remains of sawdust, wood dust and dirt;
• Remove the clutch cover, painstaking it under a stream of warm water and let it dry. Lubricate the worm gear and screw of the side tension system of the chain;
• Remove the spark plug and clean it from soot and fuel residues. Pour 5-7 ml of motor oil into the candle hole and crancele the motor for 3-4 revolutions so that the oil is distributed according to the connecting rod mechanisms and the cylinder-piston group. Leave the piston at the top (in the raised state). After that, set the candle in place, but do not put on the ignition terminal;
• Cover the saw tire and chain with protective lubricant and store wrapped in a piece of paper or fabric impregnated with oil;
• pack the tool and hide the removed parts into a dry, dark and nonsense place.

Operation of chainsaws in the cold season: the main points

The house always has a task for a chainsaw, so sending it to the “winter holidays” is not always rational. In such cases, the tool is not fully stored, t.E. Without complete disassembly.

If you plan to work with a chainsaw in winter, store it and, in particular, the fuel mixture, in a well.ventilated, dry and warm, in extreme cases, an unheated room protected from external influences. ,

Before starting work, make sure that the fuel has a temperature sufficient for ignition, and that the oil in the tool lubrication has normal viscosity. Some models of the chainsaws are equipped with a hot air supply system to the carburetor from the cylinder cooling ribs, which reduces the risk of freezing of the air filter and prevents the formation of condensation on the carburetor.

Check the lubricant system before starting work

Run the saw on the cold with a closed throttle, having previously checked the quality of the lubricant and the tension of the chain. As soon as the work is completed, the tool cannot be immediately inserted into the room. This is guaranteed to lead to the formation of condensate, so you will have to remove it, disassemble and clean it.

How to store a lawn mower in winter

This unit is sent for “well.deserved rest” in the fall, and is extracted closer to the end of spring. Due to such a long “downtime”, the requirements for the conservation of lawn mowers are very high.

Gasoline lawn mower

The main elements have a benzogazonocoster. this is an engine and cutting parts. They should pay maximum attention:

• The first condition for the correct storage is a room with a humidity of not more than 70%, as well as the absence of sharp temperature changes that increase humidity;
• If you worked a lot of a mower, particles of grass, and with them moisture could get to the internal parts of the device. Therefore, be sure to wash, clean and dry the knives and other details in the reach. Remove the remaining grass from the body, exhaust pipe, engine cooling radiators, etc.D.;
• Opinions were divided by the fuel. Some of the summer residents drain its remnants and wrapps the gas tank dry so that condensation does not form during the winter. The other half, on the contrary, fills the tank to the edges and leaves for the winter in this form. However, in this case, poor.quality gasoline can give a precipitate, which makes it difficult to launch the engine in the spring. It is still easier to remove the remaining fluids from the carburetor than to clean it from plaque and sediment, so we recommend the first option;
• Inspect the cutting knife. does it require repair and sharpening. In any case, remove and imprison it for the winter. If necessary, consult a specialist;
• The oil level should comply with the recommendations of the instructions for operating (for 4-stroke engines);
• Keep the lawn mower so that its wheels do not contact with the floor, or in a suspended position, or on stands.

Electric lawn mower

Before cleaning the unit for the winter, check the integrity of all contacts and inspect them for oxidation and rust. The rest of the electric motor does not require any special conservation measures. Rub the battery for the winter, clean the case, deck and knives from the grass and, if necessary, imprison them.

How to store a chainsaw

A prerequisite for the uninterrupted operation of the chainsaw, especially during long breaks, is its correct storage. In the article, the master plumber will tell you how to store a chainsaw correctly.

What is useful to know to each owner of a chainsaw

Modern chainsaws are equipped with a single.cylinder two.stroke carburetor engine.

note! 4-stroke and diesel units in the construction of chainsaws are not used due to a large weight-it would be very difficult to manually control such a tool

The principle of operation of the Monocilinder 2-stroke of the chainsaw:

• During the compression tact, the fuel mixture prepared in the carburetor enters the crankcase;
• In the extreme lower position, the exhaust channels of the cylinder open. spent gases and part of the fuel mixture go through them;
• A mixture of a crankcase under the influence of the piston pressure is supplied to the cylinder in which it burns;
• The resulting excess pressure moves the piston to its original position, which drives the main engine shaft.

2-stroke engines do not differ in high efficiency. Therefore, in order to reduce fuel consumption and increase the engine efficiency, many manufacturers use additional ventilation: the inlet valve opens to supply fuel to the cylinder after the release of curtain gases.

The complexity of the operation of the chainsaw in winter lies in the reaction to the low temperatures of the materials from which its nodes and components, and working fluids are made. fuel mixture and lubrication, as well as the formation of condensate on the nodes and mechanisms of the instrument at temperature differences. In addition, the cold season of the year is mostly unsuitable for the performance of economic work.

note! There is a special series of chainsaws that have admission to work in winter cold. Such models have a well.insulated case, as well as a carburetor heating system

Why is it important to properly store the tool

With the onset of cold weather, many owners of the chainsaws simply send saw equipment to the shelf in the garage, until better times. At the same time, few newcomers know that the proper storage of a chainsaw in winter involves the conservation of equipment using special technology.

With prolonged storage of chain saw technology, a complete stop of the actual mechanisms occurs, which leads to the following negative consequences:

• Friction vapors and other nodes cease to get a lubricant, which leads to their drying out.
• The old lubricant turns into a thick jelly, which over time dries and tanks.
• Seals spoils, as well as filtering elements.
• The fuel is exhausted and loses its conditional properties.

In many cases, the owners of the chainsaws have to be perplexed that the chainsaws worked properly in the fall, and in the spring he flatly refuses to start to start. All the fault of the incorrect storage of a chainsaw in winter, during the cold season of the year.

Tasks and rules for preserving equipment

The main goal of conservation of absolutely any equipment is to prevent the development of parts and mechanisms of negative processes on the working surfaces. The negative processes include:

• Corrosion;
• Dehydration/getting wet;
• The formation of sediment and evaporation of liquids;
• Dusting;
• Coropulmonary from temperature drops.

To store mothballed equipment, you should choose a place with optimal microclimate conditions. For long.term storage of a chain saw tool, a garage is ideal. In this case, good ventilation should be provided in the room. The garage must be dry and, if possible, insulated.

Regarding heating, yes, for long.term storage you need a warm and dry place. But since the heating of the room is purely for storing tools of tools is irrational, it is better to refuse constant heating. In this case, the situation may save periodic heating of the garage.

Heat accelerates moisture evaporation. But the highest result is provided by air drainages. The average household dehydrator collects up to 1-2 liters of water per day. In order to save, the drainage can be included periodically, during periods of rains and slush.

Preparation for storage and conservation of a chain saw tool

If the chainsaw is planned to be stored for a long time, it must be disassembled, cleaned, washed and dry for.

To prepare a chainsaw for winter storage, you need:

• Oil and fuel. To empty the fuel, you should start a chainsaw with an empty fuel tank. After a few seconds, the saw motor itself will stall in itself. Additionally, the engine lubrication system should also be lowered. During the winter period, the existing oil will still deteriorate. The fact is that any motor lubricant contains additives (friction modifiers, antioxidants, etc.). With a long stagnation, especially if low temperature, the additives are deactivated and precipitated.
• Disconnect the tire and remove the chain. The tire and chain should be cleaned from blockages. You can even rinse them in kerosene and dry well. The chain tire must be covered with a thin layer of preservative. Suitable movil or cannon fowdered. That is, you need to drop a little preservative on a rag and grind the spare parts for them. The tire with a chain should be stored in oiled paper, best of the parchment. But just ordinary rags are suitable.
• We extract filter elements from the chainsaw. It is necessary to extract coarse cleaning filters from the fuel tank and the neck of the lubricant system. Cricking filters are simply washed and dried. If a filter of fine fuel is provided, then it is best to simply replace it with a completely new analogue in the spring. Special attention should be paid to the air filter. The airfall filtration element must be disconnected and cleaned well. If the filter has already worked for 2-3 seasons, then it makes sense to just put in the spring a new element of air filtration.
• We unscrew the spark plug and clean the candle head, especially the electrode, from the carbon. The user must track the service life of the candle. Subject to intensive operation of the chain saw, the candle usually works out 2-3 seasons. If the chainsaws are rarely used, then the candles are enough for an average of 4-5 seasons. If good performance is expected from the chainsaw, then the spark plug should be changed every 2 years!
• Add 5 (ml) of motor oil to the candle well and scroll the crankshaft 2-3 revolutions. You can scroll the crankshaft by the asterisk of the chain. This technique will allow motor lubrication to create a thin protective layer in the cylinder.

How to store a trimmer for grass in winter

How to prepare a trimmer for grass for spring operation

You carefully looked after your lawn. you aeration, sowed, fed fertilizers Now you are waiting. Waiting for warm days and blue sky, and you know for sure that the grass will be green soon. You checked the list of what you need to do for the lawn. And your trimmer is ready for the grass? You know how to prepare a trimmer for grass? Your tool in the barn is configured and ready for the new season of the kosba? Let’s look at the list of what you need to do for a regular trimmer for grass, so that it is ready to do your job well (mow).

How to prepare fuel for a trimmer for grass

The trimmer engine for grass will work better and will be better ready for kosbe, if you add a fuel stabilizer (additive) to the fuel mixture. Before long storage, do not forget to drain all fuel. Then get the engine and let it work until it stalls, so that there is no fuel in the fuel system. When the seasoning time comes for the new season, it is very important to use a previously properly prepared mixture of oil and gasoline. This will ensure the proper performance of the 2-stroke engine of the trimmer for grass. Pre.prepared fuel eliminates the troubles and errors when mixing fuel immediately before the mowing. It is necessary to mix fuel so much to use it for a month, no longer, since when stored more than 1 month, oil precipitates and fuel ages.

How to prepare a trimmer engine for grass

Before the start of the season, you need to replace the spark plug of trimmer for grass, fuel filter, clean the air filter and adjust the carburetor. This will reduce fuel consumption and increase power. For a trimmer for grass with a 4-stroke engine, you need to check the level of motor oil and its freshness, as well as replace the oil filter.

How to prepare a fishing line for a trimmer for a trimmer for grass

Lines for a trimmer, with long.term storage (for example, after winter storage), can become dry and brittle. To prevent this and increase the service life of your fishing line, you just need to store it in a sealed bag with a small amount of water. And before starting operation (before charging a fishing line for a trimmer into a trimmer head), it is advisable to soak a fishing line for a trimmer for several days in water. Then she (a fishing line for a trimmer) will become more elastic and durable.

How to properly store a trimmer for grass

Trimmer for grass (electric or lawn mower) is a popular and useful garden tool for mowing grass, weeds and small shrubs. The technique is quite complicated, you need to correctly contact it, but also store it. Particularly important is conservation for the winter. Sometimes the owners of such equipment simply throw it into a pantry or garage for the whole winter. In such conditions, by the next season, the unit may fail. Therefore, it is important to correctly approach the conservation and organization of storage conditions.

Which affects the characteristics of a trimmer for grass

The technical condition of motorcycles during storage can change due to such factors:

• The quality of the device itself. If the manufacturer used low.quality materials and components, they themselves become unusable faster, for example, rust.
• Package. Should protect against dust, moisture and mechanical damage.
• Temperature. Should not fall below 0 ° C. Especially relevant for battery models, since the battery in the cold quickly degrades.
• Humidity. Excess moisture leads to corrosion damage to parts.
• Training. Before storage, the device must be properly served.

Storage features

There are two main types of motorcycle. gasoline and battery. The rules of their storage are mostly convergen for some nuances. In any case, the conservation should begin with thorough maintenance and preparation of the unit.

Training

Preparation of a benzotrimer begins in this way:

• Fuel and butter.
• Let the apparatus work at idle so that it consumed all the fuel left in the carburetor.
• Spin and inspect the spark plug. The electrode should have a reddish color. If there is a car, the candle should be cleaned or replaced.

Eletric trimmer for grass should begin to be prepared for conservation as follows:

• Remove the battery. It must be stored separately in a cool place, but not at minus temperature.
• Check the condition of the wiring and contacts. If there are damage to the wiring or weak contacts, they need to be corrected.
• Check the condition of the brushes. If they have worn out, it is necessary to replace.

Further, the rules are the same for both types of motorcycle:

• Remove the remaining grass. She can accumulate between fixed nodes and knives. Blades also need to be carefully cleaned. If there is organic pollution on the case, they must be carefully removed.
• Dismantle the cutting knife. Check it for mechanical damage. If there is a part, be sure to be replaced, this can be done immediately or before the next season. Store a knife separately.
• If the lawn mower is equipped with a trimmer cord (fishing line), it should be dismantled and keep in a wet place until the next season. Before the new season for several days you need to leave in clean water. Thanks to this, the fishing line for the trimmer will remain elastic, which will extend its service life.

Where and what to store

It is extremely recommended to store motorcycles in limbo. The steering wheel often interferes, so it can be dismantled or simply turned the other way. As for the choice of place and packaging, the following options can be distinguished:

• The optimal storage location is a garage or a separate building for garden equipment. The main thing is that the room is dry and well ventilated.
• If there is no separate building, a trimmer for the grass can be kept in the pantry of the house or apartment. It is desirable that the room is not very dusty, which is especially important for electric motorcycle. A large amount of dust absorbs moisture, as a result of which it begins to conduct electric current, which is fraught with a closure.
• It is better to use factory packaging in which a trimmer for grass was sold. Very good if it has a foam, it will absorb excess moisture. In such a package, the device is not necessary to hang.
• If there is no factory packaging, you can use a cardboard box of a suitable size.
• You can apply a suitable cover of dense fabric, for example, tarpaulin. In such a package, a trimmer for grass will be conveniently hanging on the wall, to save space.
• You can build a box of boards or plywood. However, in such a box, the lawn mower will take up a lot of space.
• Trimmer for grass can be wrapped in a breathable fabric.
• If there is no packaging at all, it is recommended to store the device in a suspended form. This will protect the details from mechanical damage and will save place. But, it is important that there is no dust in the room, especially from building materials. For suspension, it is enough to mount a hook of the corresponding size into the wall.

Useful tips

To avoid premature failure of a trimmer for grass, follow the following recommendations:

Conservation setting

Most of the owners of the chainsaws prefer not to work as a gas tool in winter, but put it on conservation, without waiting for strong cold weather.

To prepare a chainsaw for winter storage, you need:

• Oil and fuel.
• Using a wire probe or a home-made hook from fuel and oil tanks, extract filters-endors, which should be washed, and if necessary, replace and install back.
• Start the saw and let it work on idle for the complete removal of liquids from the carburetor channels and the lubricant system.
• Remove the saw chain and tire and how to cleanse them of the remains of wood, dust and dirt.

The saw tire and the chain before packaging should be covered with protective lubricant and stored in fabric or paper impregnated with oil. The tool and its main nodes need to be protected from exposure to direct sunlight, which can cause fragility of some details.

When preserving the chainsaws, it is recommended to perform the crankshaft to update the lubricant of the KSHM and CPG at least 1 time per month.

Rosopil’s rehabilitation: main points

With the onset of spring, much more work appears in the household than in the winter season. This means that the time has come for a chainsaw. it needs to be re.registered and prepared for the beginning of work. The procedure will be as follows:

• External inspection of the tool for minor malfunctions and their elimination.
• Checking the state of the spark plug, if necessary. replacement.
• Checking fuel and air filters.
• Updating the sharpening of the saw chain.
• Installation of a saw tire and a chain headset with a subsequent stretch.
• Filling the oil tank and lubrication of points and friction surfaces.
• Preparing fresh fuel mixture and filling it into the tank.
• Checking the brake of the quapi.
• Checking the starter mechanism.
• Launch and control of the work of the chainsaw at idle.

With prolonged storage, the fuel mixture loses its qualities, so this should not be used. This can lead to various troubles, starting from the loss of engine power and ending with the contamination of the carburetor channels and the fuel supply system.

Sharpening of the saw chain in the photo

As in the case of the commissioning of new chainsaws, the saw set of the tool removed from the conservation is important to adjust correctly. The chain should not bite the material and move with jerks. If it is pulled, thimes will be carried out with difficulty, if weakened. significant vibrations and beating arise when cutting. You can determine the degree of tension by taking the chain by the tooth in the area of ​​the end of the tire and pulling it out. With proper adjustment of about a third of the shank, it will remain in the groove of the saw tire, and the chain itself will move freely.

Some models of chainsaws are equipped with a system of automatic adjustment of the chain tension. However, in this case, the quality of the installation of the chain headset always needs to be checked what is called visually and manually.

Only the correct attitude to the tool can ensure its normal operation and long service life. Do not forget to put your chainsaw on winter conservation and perform all the necessary actions to launch it into work with the onset of spring-and it will last you as long as possible, without delivering any trouble.