Storing a single axle tractor in winter. Lifan 168F-2R 7A

Storing a power tiller in winter

For a single-axle tractor (power tiller) to last a long time, it needs proper care. Maintenance of the equipment includes preparation for work, cleaning after work, timely maintenance, as well as proper storage of the trimmer in winter. If you do not plan to operate the single-axle tractor in the cold season, you should perform its preservation. Otherwise, when winter is over and it’s time to plow, a number of problems may arise. from hard to start the engine to major repairs. To avoid complications and extra costs, there are a few simple rules to keep in mind. To learn how to store the single axle tractor (cultivator) please refer to the instruction manual. In this article we will note the general rules of conservation of equipment.

Equipment preservation begins with its thorough cleaning. Particular attention should be paid to places difficult to access and where dirt accumulates. When removing dirt from the surface of the product, it is not recommended to use iron scrapers, because.к. they damage the protective coating, which leads to rust. All parts of your power tiller should be wiped dry after cleaning. No moisture should remain on the surface of the product to avoid corrosion. The same thorough cleaning is also required for the attachments.

Then the single axle tractor (cultivator) must be inspected for damage and breakage. If parts are found to be in disrepair, they should be replaced. If you have experience, you can do it yourself or go to the service center.

Spare parts for the “Neva” power tiller are available at the factory of JSC “KO-Neva”.

Recommendations for equipment preparation for winter

A single-axis tractor is a universal equipment, which helps to work on your plot or even on a mini-farm. To make the equipment last for a very long time, it must be carefully cared for. And this includes not only cleaning after work, oil changes, timely repair, but also preparing it for the winter.

A single-axle tractor cannot simply be thrown into a garage or barn, where there is high humidity, and just, at best, cover it with a tarpaulin. As a result, you will face such a problem, as the machine stops to start in the spring. Are these problems worth the trouble of not preparing for winter without following some simple recommendations?

For winter storage you need to carefully prepare your single axle tractor. This is necessary so that in the warm season you can start the machine without any problems and start using it immediately.

Preparing your power tiller for winter

Before sending the single-axle tractor for winter storage a number of procedures have to be performed for its successful “wintering” and quality work in the spring. First of all, before the onset of frost the single-axle tractor should be washed and thoroughly dried and minor faults should be repaired. Lubricate all operating mechanisms and assemblies thoroughly. Also clean, sharpen and lubricate the cutting attachments. The single-axle tractor should be stored in a dry, ventilated room. No need for additional heating.

Basic rules for preserving a power tiller for winter:

• Change oil in gearbox and engine.
• Clean and oil the air filters (if a tub is provided for them).
• It is recommended to unscrew the spark plug, pour a few milliliters of oil into the cylinder and manually crank the crankshaft several times.
• If your power tiller has a battery, remove it and take it to a warm place. Also remember to charge the battery a few times over the winter.
• On a clean and dry single axle tractor you can also apply a special rust preventive coating, which you can buy in specialized stores.

We suggest you also read the video, which shows the process of preparing your power tiller for winter:

How to prepare a single axle tractor for winter?

Many farmers have equipment such as power tillers and power tillers. Both of these units help to perform any work on the ground, as well as in the care of the territory of the plot. Motorcycles can also be used in the winter to clear snow and remove it, break up icy patches and sweep paths. But often machinery is not used in winter and is simply put away for storage.

A single axle tractor in winter cannot simply be left until spring. It is necessary to carefully prepare it for the cold, and protect the parts from corrosion. In this article we will tell you how to prepare your machine for winter storage. Is it worth it to drain the fuel, take off the wheels? All of these questions are answered by us.

Recommendations for winter preparation

A single-axle tractor cannot simply be thrown into a garage or barn where there is high humidity, and just, at best, cover it with a tarp. As a result, you will face such a problem as the machine will stop starting in the spring. Are these problems worth it if you just don’t prepare for winter without following some simple recommendations?

A single axle tractor must be carefully prepared for winter storage which in a more professional language is called mothballing. This is necessary so that in the warm season you can start the machine without any problems and start using it immediately.

General rules

Any technique, including power tillers, prepares for winter according to certain rules. Preservation of the unit begins with a thorough cleaning. You can not leave the product all in the dirt and ground. After cleaning, you must dry it thoroughly because moisture can damage parts and rust will appear.

Sharpen all cutting parts of tools thoroughly. Check the power cord and, if necessary, replace it before spring arrives. With these recommendations you are unlikely to have problems with the technician in the spring.

How to store a single axle tractor in winter?

Such complex equipment, such as motor blocks and motor cultivators, require special preparation for storage in winter. The difficulty is that because of the abundance of different parts and mechanisms it is very difficult to clean them from dirt, but it is necessary to try to do this. The process of preparing for winter consists of several steps:

If you follow these simple guidelines, you can easily extend the life of your equipment. In addition, you will avoid a number of problems like corrosion or failure in the system due to moisture, which will eventually require costly repairs or even replacing some elements.

Preparing for the new season

So, your single-axle tractor survived the winter safely and now it needs to be prepared for the new season, for new loads and work. Such a process also includes several steps to identify possible malfunctions and prevent new ones:

• Change the fuel immediately. If you have any gas left in the tank, drain it and refill it with new gas. Over the winter, it may have oxidized and even created a sediment;
• Check the spark plug. It should stand very securely and there should be no air access to it;
• The fuel tap must be opened;
• The lever for the air damper should be closed until the engine has warmed up;
• Set the ignition switch to on so you can start the engine;
• How to start the engine? Pull the starter grip, you will feel resistance, then pull more sharply. This is due to the compression of the fuel-air mass inside the combustion chamber. Do not be surprised if the engine starts to smoke. It happens because of oil combustion.

After that your machine should operate normally without malfunctioning or breakdowns. If there are any malfunctions, you’d better locate and repair them immediately so that you don’t make things worse in the future.

How to drain gasoline from the tank of the car LADA Granta?

Turn on the ignition, but DO NOT START the engine! The gasoline pump will turn on for a few seconds and pump fuel. Thus, turning the ignition on and off several times, you can drain a sufficient amount of gasoline from the fuel tank.

In order to drain the fuel from the foreign car is necessary:

Unscrew the fuel filler cap. Find out where in your vehicle the fuel pump is located and where the fuel line is routed to the engine. Then loosen the clamps, you may need a screwdriver or spanner (8 or 10″).

Preparing the power tiller for winter

Before putting the single axle tractor into winter storage, a number of procedures must be carried out for its successful “wintering” and quality work in the spring. First of all, before the onset of frost, the single-axle tractor should be washed and thoroughly dried, eliminate minor damages. Lubricate all working parts and assemblies thoroughly. Clean, sharpen, and lubricate the cutting elements of the attachment as well.

The single axle tractor should be stored in a dry and ventilated place. There is no need for additional heating.

Basic rules for preserving your power tiller for winter:

• Change oil in gearbox and engine.
• Clean and oil the air filters (if a tub is provided for them).
• It is recommended to unscrew the spark plug, pour a few milliliters of oil into the cylinder and manually rotate the crankshaft several times.
• If the power tiller has a battery installed. remove it and take it to a warm room. Also remember to charge the engine several times over the winter.
• You can also apply a special anti-corrosion coating to a cleaned and dry single axle tractor, which can be purchased at specialized stores.

We also suggest you read a video that shows the process of preparing your power tiller for winter:

How to prepare your power tiller for winter storage

Important question for cultivator owners: How to prepare the machine for winter “rest. The room in which you will winterize your cultivator must not be dusty or damp. To prepare the machine for a long standstill, it needs to be preserved. All work should be done with the engine cold.

You need to service your power tiller not only before the winter months but also if you don’t want to use it for a long time.

Draining the fuel

Try to work out the fuel as much as possible beforehand, the remaining fuel must be drained from the tank and carburetor. For this, most models have a special drain screw or plug. Unscrew it, put some container of fuel under the carburetor, and open the fuel lever. When the gasoline flows out, you need to close the hole and the fuel lever. Test start the engine outdoors to make sure there is no fuel left in the carburetor. The DigiTrak hydraulic system is equipped with a fuel system that allows you to remove fuel residue and fuel additives from the fuel system before you buy fuel.

Old fuel that has been stored for more than 30 days is unsuitable for operation. Gasoline oxidizes and increases the tar in it. The carburetor of a cultivator can become clogged if you do not drain the gasoline for a period of storage of more than a month.

You can also change the oil if necessary.

Replace a spark plug

On most power tillers, the spark plug must be unscrewed. It is necessary to evaluate its condition and in case of failure. Replace. To unscrew the spark plug, remove the cap, and clean the dirt around the spark plug. Use a spark plug wrench to unscrew the part and carefully inspect. Note the electrode gap. The appearance not only indicates the serviceability of the spark plug itself, but also the engine of the unit. If the electrode is covered with velvety black carbon deposits, it must be replaced. Manufacturers usually list the recommended spark plug models in the manual. Failure of this element can lead to high fuel consumption, loss of power, difficult starting, etc.

A properly working spark plug has an electrode gap of 0.7. 0.8 mm. The electrode is light brown, with minimal deposits and carbon build-up. No trace of oil.

Black carbon build-up and traces of unburned oil or fuel could indicate a faulty engine.

Lubricate the shaft

After unscrewing the spark plug you fill the cylinder with approx. one tablespoon of engine oil. Slowly pull the starter handle until resistance is encountered, this will turn the crankshaft and lubricate the piston rings. At the same time you will close the engine intake and exhaust valves, protecting the inside of the engine from corrosion.

Tip: To pour oil into the cylinder you can use a 10-20 ml syringe.

Last preparations

Your cultivator needs to be in good condition. Inspect it thoroughly. Clean the cutters of dirt and grass residue, lubricate them. If the paint is peeling in some places, it needs to be peeled off and those places need oiling. Lubricate all visible controls: levers and ropes. Clean the air filter. To save space in the garage, you can remove the cutters and fold down the handles.

Now your lawn trimmer is ready for a well-deserved rest and can look forward to the new season!

Do I have to drain the gasoline from my power tiller in winter??

Prepare the fuel tank thoroughly for winter. It is here that specialists have different opinions: someone says that the tank should be dried by draining the fuel completely, and someone, on the contrary, advises to fill it completely.

In the first case, corrosion can still appear, because it may happen that you have not completely drained the fuel tank. But if it is completely filled with fuel, as in the second case, it is more likely to cause a fire, and that is a much more serious and dangerous problem. We recommend that you follow the instructions and do not risk your life or property.

My list of actions for starting:

Disconnecting the oil level gauge.

This sensor is a float in the oil sump. If it stands unsteadily, it opens the ignition circuit. In winter it often freezes on the crankcase wall and until it is in place, it will be impossible to start the engine.

Disconnect sensor wire at front of crankcase.

p.s. Always check oil presence in the crankcase before turning off the sensor.

Removing the air filter.

This is what happens when there is not enough oxygen in the combustion chamber to start. After the last operation, the paper filter picked up moist air, cooled down, condensation formed on the paper, which froze and prevented fresh air from entering the combustion chamber.