Trimmer for grass for grass for a trimmer to wind. Trimmer head for grass with automatic line dressing

How to wind a fishing line for a trimmer to a trimmer coil for grass

Head. the main detail of the trimmer for the grass. It is a basis with a reel on which the cord thread is wound. In total, 3 types of heads are distinguished:

• Manual. Allows you to lengthen the cord (fishing line for trimmer) manually after a complete stop of the engine.
• Semi.automatic. Using such a head is simplicity and convenience. It acts on the following principle: waiting for the trimmer for the grass reaches the maximum revolutions, the user is slightly knocking the device with the device about the ground, due to which the locking of the fishing line is removed. Thus, the cord is put forward at the expense of centrifugal force, and the owner of the apparatus can only cut it with a knife.
• Automatic. Trimmer fishing line is supplied after reducing engine speeds. Such a head is convenient in cases where there is a need to carry out long.term work. The disadvantage of the device, in turn, is the rapid wear of the cord.free thread.

Now, in order to find out how to refuel a trimmer to the grass, you should pay attention to the choice of cordy thread.

The choice of fishing line

In order to easily wrap a fishing line for a trimmer to a trimmer coil for grass, it is worth deciding on what tasks the garden tool will perform. The thicker the thread tucked into the head, the more difficult the tasks that it can complete. It should be noted that a universal thread is often used, the width of which does not exceed 2 mm. You, in turn, can decide on the size, using the following methods:

• get acquainted with the information set out in the instructions from the manufacturer;
• check the suitability of the fishing line for use on your own, trying to insert it into the coil hole;
• study the spool for information about diameters allowed for use.

Selection of fishing line for refueling a trimmer for grass can be carried out by engine type. So, for example, an overly thick thread can affect an increase in rotational resistance. Because of this, the load on the engine will increase, which will certainly affect the quality and timing of its further operation.

Avoiding negative consequences is easy. To do this, it must be borne in mind that for electric motors with a power of up to 500 W, a fishing line for a trimmer with a diameter of up to 1.2 mm is ideal. If you cannot get such a thread, you can use the cord by 1.6 mm. A thread with a diameter of 2 mm, in turn, is used for engines with a power of more than 1 kW. It is worth noting that the cord for 2 mm is often used for winding on a bent mower. If the gasoline device has a straight shaft, the thread should be used 2.5 or 3 mm. The thickest fishing lines are installed exclusively on devices, the power of which is equal or exceeds 1.3 kW.

The last, but no less important factor is the type of fishing cross section. When choosing it, it is worth focusing on the tasks set before the garden tool. There are several demanded cross.sectional options:

• twisted-has a small margin of safety, which is why it suits exclusively for young grass;
• Substitute. is characterized by sharp edges suitable for working on overgrown weeds;
• Round. the most common section. Such fishing lines cope well with fresh grass, but they are not suitable for shrubs and dry ones;
• rectangular, square and star type of cross section-due to low strength, are used to work on lawns.

The most durable and universal cord is a two.component fishing line for a trimmer with a round cross section, inside which the core is located. It is this thread that is suitable for the majority of work. It must be remembered that the use of fishing fishing line, ordinary wire and other third.party materials as a cord pose a danger to others.

How to replace a fishing line for a trimmer on a trimmer?

Replacing the fishing line of the trimmer for the grass with step.by.step instructions will even allow the owner of the lawn mowed inexpensive in such matters to do a fairly difficult job.

However, before starting work to replace the fishing line on the trimmer, it is necessary to ensure the safety of work. In particular, it should be taken protection measures against careless or spontaneous inclusion of the lawn mower:

• Exclude spontaneous start,
• Delete the battery (if used),
• Place the tool on a comfortable site for work.

It is convenient to perform work on replacing the fishing line for the grass when the lawn mower lies on the table, and the master, who is performed by replacing the fishing line of the trimmer for the grass, has the opportunity to approach the instrument from any side.

Remove the head of the head of the grass for the grass

At the first stage of disassembly, the head of the head of the grass is removed. On the example of the models of trimmers “Black and Decker” and others, it is usually enough to apply some pressure to squeeze the click-fixer, which are on the side of the head of the head of the head of the head of the head of the body to remove the lid to remove the lid.

Some models of lawn mowers initially include dismantling the head of a trimmer for grass, for which a playback key is used, which is included in the tool kit. The head is usually held by two or three screws, access to which is provided through the side holes of the rear decorative cover.

The head cover, where the coil with a fishing line is installed, is usually held due. It is enough for some effort to squeeze the tongue-thorough and slightly turn the lid, after which the lid is easily removed

At the time of squeezing the tongue-fixer, you need to turn slightly and raise the head of the head of the trimmer for the grass to remove the winding drum.

Step two: extracting a winding drum (coil) with a fishing line

The next step in the process is the exhaust drum with a fishing line from the inner region of the head. You need to turn the head with an open side to see a fishing line for a trimmer and a reel. On the side of the head, find two recesses (eyelets) through which the fishing line for the trimmer is bred outside.

You should release a fishing line for a trimmer from the holes by checking the drum. Then gently remove the coil from the head of the head. The winding drum of some models is installed on the spring. This moment must be taken into account by performing the operation to extract.

The procedure for extracting a coil of a trimmer for grass with a fishing line from the inner region of the head: 1. head assembly with a coil; 2. extracting neatly with a small axial turn; 3. extracted details

The old fishing line for the trimmer is completely removed from the coil. To remove the old fishing line for grass, you need to remove the forest from the loops and pull the free end. This method is removed by the whole old winding. A similar process is repeated on the second section of the drum. The master is recommended to use gloves when performing work.

Installation of a new fishing line on the coil of a trimmer for grass

Equipping the coil with a new fishing line is performed in the reverse order. The procedure looks like it is described below, regardless of the model of the lawn mower:

Step one: fixing and styling

Fold the end of the fishing line in half. Place the workpiece above the coil on each side of each half of the winding area. Wrap both halves completely around the winding drum. Stretch the fishing line for the trimmer through the loop.

The procedure for preparing fishing line in the field of both wound sections of the drum. The loops are laid in specially made cutouts, after which the winding of the fishing line is performed in each area

Pull the fishing line for the trimmer enough and put the knot in the groove made on each side of the winding drum.

Step two: winding cutting material according to sections

The next step is to turn the fishing line in a circle of coil, observing caution. It is necessary that each half be filled with “its own” winding, exactly, without intersections. Usually on the hull of the winding drum you can see the arrows indicating the direction of winding. This moment should be borne in mind, filling the reel with a fishing line.

Step Three: The Club of the Head Noner

Stretch the ends of the fishing line through a pair of oval cuts of coil. Replace both goals and a spring (if any in the design) with new elements included in the package. Bend both ends of the fishing line at right angles.

The last technical stroke of the process of replacing the fishing line on the trimmer is to put the cover on the head with subsequent fixation by pressure and slight turnover.

Let each end into the hole, which is at the base of the winding drum. Install the coil in the inner area of ​​the head with an emphasis on the spring. Put the lid, leve on the base and light pressure down with a small rotation counterclockwise, put the cover on the tongues of the latch. This is where the replacement procedure is completed.

We carry out the winding of the fishing line

Sentlessly completed disassembly of a spray coil without losing its spare parts allows you to go to the main task-winding into a fishing line coil. Technological features of the design of the spool and the number of working antennae determine the sequence of actions.

Coil with one working osik

The easiest option and a simple sequence of actions:

• The dimensions of the bobbin and the length of the original factory winding determine the length of the fishing line recommended for winding. 2 5 m.
• One end of the fishing line is inserted into the fixing technological hole located inside the spool.
• The fishing line for the trimmer is wound on the drum in reverse rotation of the spray in the trimmer product direction. as a rule, on the inside of the bobin, the arrow indicates which direction the winding is carried out.
• A small section of the fishing line is left free to output it. it is fixed in a specialized border on the inside of the bobbin, designed to keep the winding when assembling a spool in working condition.
• The left end of the fishing line is passed through the hole of the outer part of the bobbin.
• Half of the bobbin are collected and put on the bar of the trimmer device.

Two working antennae

In this type of spools, the number of grooves for winding the fishing line lying on the inside of the coil should be determined:

For both cases, a fishing line for a trimmer 2-3 m long is taken. In a single.captable coils, the fishing line for a trimmer stretches into a through hole, its ends (antennae) are folded together and aligned, after which they are wound in the back of the rotation of the bobbin on the bar the side. inside the arrow is usually indicated the correct direction of the winding. In the presence of fixing grooves, the ends of the fishing line are threaded in them or hold their free arm fingers, spread into the through hole of the outer half of the bobin, the spool is closed and attached to the bar of the trimmer product.

The difference between the winding of the fishing line in the two-to-dancing coils is that initially a line of fishing line 2-5 m long is folded in half (to determine the middle fold), and the bend loop is inserted into a special groove between the grooves. Both strains of the fishing line are wound each in its own groove, fixing the antennae and assembly of the coil is similar to the option considered above with one groove.

The first implementation of this procedure may seem long and quite time.consuming, but over time and experience, this task will be solved much faster and easier.

The video below will clearly show how to refuel a fishing line for a trimmer to the coil of a trimmer for the grass and correct it correctly. this operation is not a complicated one and, with some patience, will necessarily be crowned with success:

How to wind a fishing line for a trimmer to a trimmer coil for grass

The refueling of the fishing line in the coil of the tool, at first glance, is not easy. But to carefully study this process carefully-and in the future all the necessary actions will be carried out without any difficulties.

To find out how to refuel a fishing line for a trimmer trimmer for grass, you should read this guide. The step.by.step instruction below takes into account the features of the coils of different types of trimmers, therefore it applies to any tool.

• The reel with a fishing line is the lower edge of the trimmer for the grass. First, of course, it is necessary to remove this head from the device. To do this, fix the rod (or, in other words, the shaft) on which the coil is attached. Fix it in such a way that it does not scroll at. This is the easiest to do this by placing a peculiar stupor between the thread of the shaft through a special hole (best metallic). When the shaft is fixed, you can unscrew the coil.
• At this stage, it will be necessary to extract a bobbin from the head, on which a fishing line for a trimmer is attached. To do this, you need to disassemble the head to the elements. To do this, you must first find a fixer on its case. It is located on the circumference of the product and is the likeness of the buttons. When the lock is found, you need to press it with an effort. Holding the latch pressed, you need to turn the head cover clockwise. Then you need to remove the lid and remove the bobbin.
• A tight spring is placed between the bobbin and the head. It must be set aside for a while so that it does not interfere with the winding process. Before proceeding to the winding of the fishing line, it is necessary to inspect the bobbin. If it has the remains of an old fishing line, they must be removed. When the bobbin is cleaned, you can start preparing a new skein.
• From a pre.prepared skein of a new fishing line, it is necessary to measure and cut off six (maximum. seven) meters. Spulk should be at hand.

At this moment, the key stage actually begins, which is devoted to this article.

The first method of winding fishing

The required amount of fishing line is cut off. Now you need to carefully examine the bobbin to understand what type it belongs to. It depends on this how to wind the fishing line for the trimmer.

Spulks are of two types. In general, they are slightly different from each other. Regardless of the species, the coil is divided into two compartments. the upper and lower. In the first type, the dividing line does not close into the ring and has a deepening.

The second type is solid, but near it on the sides on both sides there are small through holes. The method of winding the thread must be studied depending on which of the above species the coil belongs.

• The previously prepared six.meter segment must be bent in half. Best not exactly in the middle, but so that one half turned out to be about fifteen centimeters longer.
• Then the bending place must be inserted into the recess in the dividing line. One half of the fishing line should be in the upper part of the coil, the other half in the lower part.
• Now you can proceed directly to the winding. You need to wind up in the direction in which the arrow on the bobbin indicates. When winding, you need to keep the threads so that they are not intertwined and the upper half is wound into the upper part of the coil, and the lower half into the lower part. Each half should remain free about fifteen centimeters from the end.
• There are small recesses (or, in other words, grooves) in the upper edge of the bobbin to fix the consumable. The ends of the threads need to be inserted into these recesses so that they are fixed one opposite the other.
• The final stage of refueling the consumable in the tool. the ends fixed on the bobbin must be put into the corresponding holes in the head of the trimmer for grass.
• That’s all. The winding process is completed. Now it remains only to collect the head into a single whole. The spring is neatly placed back between the bobbin and the head. Then you need to insert the bobbin into the head and press them to each other.
• Free ends of threads are recommended to pull out more tightly. To do this, take turns pulling the ends of the consumables so as to extract them from the grooves of the bobbin. You can make sure that the cutting element is extracted from the holding grooves, having tried to pull the threads a little. they must freely go through the holes in the head.
• Clutching a bobbin downward, you need to put on a lid over it. The lid must be screwed to the head so that all the grooves on their buildings are compatible and the bobbin remains between them.
• And finally, the very last action. the head is screwed back to its place in the lower part of the tool.

The process is completed. Trimmer fishing line is tucked up. Trimmer for grass is ready for further work.

The second method of winding

• The previously prepared segment is six meters long, you need to bend exactly in the middle and cut. Thus, two segments of the same length are obtained.
• At one end of each segment, you need to make a small “hook”. To do this, bend a couple of centimeters from the edge and briefly fix it so that the “hook” does not extend.
• Then one segment is taken. The “hook” is inserted into the through hole in the upper part of the bobbin.
• Now you can start the key stage. winding. The direction in which you need to wind up indicates the arrow on the bobbin. It is important to ensure that the fishing line for the trimmer is wound strictly within the upper part of the coil. It is not necessary to wind the thread to the tip. from the end should remain free about fifteen centimeters.
• There are small recesses (the so.called grooves) in the upper edge of the coil to fix the consumable. Free “tail” of the thread must be inserted into one of these recesses.
• The upper part of the coil is filled. Now you need to do the same procedure with the lower part. The second section of the thread is taken. “Hook” is spreading into the through hole in the lower part of the bobbin.
• After that, you can start wrapping a fishing line for a trimmer (within the lower compartment). And this segment also needs to be left with free ones about fifteen centimeters from the end. This remaining “tail” must be inserted into a recess opposite to the one in which the end of the first segment is inserted.

How to choose a fishing line for a trimmer for a trimmer for grass

The trimmer for the grass bought in the store is already ready to work. a standard nylon fishing forest is tucked into it. She cuts the grass, but does not cope with work poorly. only young, thin plants quickly fail and mows. She does not take old grass and weeds with stem stems or cuts off at all, wear out quickly. It grabs it for a short time, after which you need to replace the fishing line for a trimmer in a trimmer.

It is not recommended to use a fishing fishing line for a trimmer, it is better to take a special thread with a fiberglass core. It is sold in construction stores. Stop your choice on an option that has a square or triangle in a section. their sharp edges will work like knives.

Fishing line consumption for a trimmer for grass using faceted and reinforced consumables will decrease by 2-3 times, performance will increase by the same amount compared to the circle of round section and fishing line not reinforced with fiberglass.

Purchase material with a diameter not less than recommended by the manufacturer. If the diameter is unknown, you need to look at the size of the holes on the outer body of the mowing head: the diameter of the working thread should be slightly smaller than the hole to pass through it freely.

Buy a sufficient supply of cutting thread (with 2-3 replacements), try to buy different options to compare which one is best in work.

Upon learning how much material is needed for one winding, focus on the length of the forest during the next purchases, so that there are no too short for winding pieces.

To replace the forest on a mechanical spit with your own hands, you need to disassemble the braid head and get the coil on which the working thread is wound.

How to remove a fishing line for a trimmer

To replace a fishing line for a trimmer in a trimmer, remove the head cover. To do this, press the fingers of the latches of fixers located on both sides of the lid, and pull the lid up. Access to the coil will open. After that, pull it out, pulling up the axis on which the coil sits. If the ends of the fishing line stick out from the holes of the head, then lift the coil along the axis and pull the remaining fishing line from the holes of the head. Now the detail does not hold anything and it is easy to remove and remove the remaining working thread.

The coil is divided into two parts by the central partition with a neckline. Different models of cobs differ in size, so you need to check how much you can wind the fishing lines on the bobbin. Its length ranges between 1 and 4 m.

Choose a fishing line for a trimmer

The fishing line for the trimmer should be strong, stiff and flexible. in the trimmer it serves as a working tool for cutting grass. Flacks of different thicknesses are made. from 1.2 mm to 4.0 mm. Most models are designed for the maximum thickness of the thread of 3 mm. What is the diameter of the fishing line for the grass for grass in one case or another depends on a number of factors.

Depending on the hardness of mowing vegetation:

It is important to consider that too thin thread accelerates the wear of the motor, too rough. will accelerate its overheating and premature failure.

The structure of the cord of the fishing line matters:

• round. universal, most durable, for rough grass;
• curly. for soft plants;
• Twisted with notch. for thin long stems.

Important! Choose a fishing line for a trimmer of the type and parameters that the manufacturer Motokos recommends. Such material will work for a long time and efficiently with optimal loads on the product of the product.

How to change a fishing line for a trimmer on a trimmer

The fishing line for a trimmer is wound on a coil (bobbin), which is located in the body of the head of the trimmer for the grass. First, unscrew the head from the bar with the motorcycle cord and open it the top cover, pressing on the side latches. In some models, the case simply spins.

We take out the coil, clean it from dirt, the remains of the old fishing line. Coils are one- and two-section.

Fishing line winding on a single.section coil

We take 2 m of fishing line, we spread it up to half through a special hole inside the coil. The ends of the fishing line of the same length stick out from both sides. We wrap them with both along the groove of the coil in the direction indicated by the arrow on the case (back to the rotation of the coil on the shaft of a trimmer for grass). We do not wound the fishing line for the trimmer to the end-pieces of 10-15 cm, which will be workers, fix in grooves on board the coil. Fixation is needed so that the fishing line for the trimmer is not unwound when installing it in the head of a trimmer for grass.

We insert the coil into the body of the head, while at the same time we spread the free ends of the fishing line into the holes of the body, set. We collect the head, put it on a trimmer for the grass. Everything, the change of fishing line in the trimmer was carried out.

How to wind a fishing line for a trimmer for a trimmer for grass with a two.section coil

If there are two sections in the coil, put the fishing line for the trimmer in half and insert the fold place into a special groove in the side between the sections. We begin to wind the ends each in its own groove. then everything, as in the case of a single.section coil.

How much fishing line is wrapped on a trimmer for grass? You can wind 2-4 m, depending on the product model. In each case, it is impossible to wind too tight, the thread should have a free move for stretching during operation.

How to choose a fishing line for a trimmer for a trimmer for grass

The trimmer for the grass bought in the store is already ready to work. a standard nylon fishing forest is tucked into it. She cuts the grass, but does not cope with work poorly. only young, thin plants quickly fail and mows. She does not take old grass and weeds with stem stems or cuts off at all, wear out quickly. It grabs it for a short time, after which you need to replace the fishing line for a trimmer in a trimmer.

It is not recommended to use a fishing fishing line for a trimmer, it is better to take a special thread with a fiberglass core. It is sold in construction stores. Stop your choice on an option that has a square or triangle in a section. their sharp edges will work like knives.

Fishing line consumption for a trimmer for grass using faceted and reinforced consumables will decrease by 2-3 times, performance will increase by the same amount compared to the circle of round section and fishing line not reinforced with fiberglass.

Purchase material with a diameter not less than recommended by the manufacturer. If the diameter is unknown, you need to look at the size of the holes on the outer body of the mowing head: the diameter of the working thread should be slightly smaller than the hole to pass through it freely.

Buy a sufficient supply of cutting thread (with 2-3 replacements), try to buy different options to compare which one is best in work.

Upon learning how much material is needed for one winding, focus on the length of the forest during the next purchases, so that there are no too short for winding pieces.

To replace the forest on a mechanical spit with your own hands, you need to disassemble the braid head and get the coil on which the working thread is wound.

How to remove a fishing line for a trimmer

To replace a fishing line for a trimmer in a trimmer, remove the head cover. To do this, press the fingers of the latches of fixers located on both sides of the lid, and pull the lid up. Access to the coil will open. After that, pull it out, pulling up the axis on which the coil sits. If the ends of the fishing line stick out from the holes of the head, then lift the coil along the axis and pull the remaining fishing line from the holes of the head. Now the detail does not hold anything and it is easy to remove and remove the remaining working thread.

The coil is divided into two parts by the central partition with a neckline. Different models of cobs differ in size, so you need to check how much you can wind the fishing lines on the bobbin. Its length ranges between 1 and 4 m.

Instructions with a step.by.step description how to wind the coil of a trimmer for grass and lawn mower

In order not to make a mistake with the choice of a suitable fishing line for your tool, you should first disassemble the head and look at the side wall of the coil. This information is usually presented on a tip, which will not allow us to make a mistake using the appropriate equipment.

If the information on the coil about what diameter the fishing line for the trimmer can be refueled, then this information can be clarified in the instructions. Having decided on the thickness or diameter of the equipment, it remains to figure out how to charge it. There are two ways for this, but not for all they are applicable. Consider both methods in details, and already depending on what models and trimmers you use, you are determined on your own which option is suitable.

It is interesting! The principle of how to wind a fishing line for a trimmer for a tip of motorcycles is appropriate not only for autonomous benzar groups, but also for electric trimmers.

The second method differs from the first in that not a whole piece of equipment is charged into the coil, but segments of two parts. Manufacturers use this way, and it is also suitable for those who have the remains of the material. The principle of how to insert two segments of the fishing line into the tip of the motorcycles, the same with the first way, and to make sure of this, below is a detailed instruction:

• There are two equal lengths of the segment of the material that you can use
• One segment is taken, and the edge is bend in the form of a clamping bracket or hook, with which the fishing line will be fixed
• Inside the coil, there are holes in the form of a bracket for fixation, which are there for a reason. If they are not, then the second option will not work. The appearance of these brackets is shown in the photo below. Each bracket is on its own
• The line of fishing line should catch on the bracket, and make it wound in compliance with the direction of the arrow
• The equipment is wound until the segment of 10-15 cm remains, which is fixed in the corresponding hole on the side of the tip
• The same manipulations with the second end of the fishing line are carried out
• The protrusions are starting into the holes of the head, and then, extracting the equipment from temporary fasteners in the coil, a cover with clamps is installed

The above instructions on how to install a fishing line for a trimmer in a motorcycle will help not only correctly, but also quickly perform a replacement procedure. The assembly of the coil of the trimmer for the grass, as mentioned above, can be performed without removing the head, but in this case you will need to conveniently fix the tool. Video Instruction is presented below.

Principle of operation

If we consider the principle of the trimmer for the grass, then it looks like a manual braid. The difference is that it is equipped with an engine, with its help the cutting element is brought into rotation.

Producer companies produce the following models of mowers:

• On which a gasoline engine is installed. Such garden tools have a fuel tank, this is their distinguishing feature.
• Electric engine devices. These tools have less weight, because they do not have a fuel tank. But when choosing such models, you need to take into account that a power source needs their work to work.

All electric braids for grass can be divided into those that work on batteries, and models connected to an electric network. Each species has its own characteristics, but they affect the power supply unit. If you do not take into account it, then the rest of the design are similar in different devices.

If you take any model of a trimmer for grass, then it consists of such elements as:

• motor;
• fuel tank (electric motor does not have it);
• levers with which the mowing is controlled;
• knife for cutting grass;
• barbell;
• Spool with wound fishing line, which is cutting grass;
• protective casing;
• conical gearbox.

The engine is placed near the mowing head, it can be installed from below or from above. Only those models that have a direct bar with a gearbox. If it is curved, then the indigenous bearing becomes a connecting element. It consists of 2 bushings.

As a cutting device, a fishing line for a trimmer is used. It is easy to replace with steel knives and discs, they can be made of plastic or metal.

The choice of cutting element depends on how hard the grass will have to mow. Most often, the work uses a fishing line for a trimmer, it is called the cord. There are products of various shapes on sale, among buyers a spiral and round is in demand.

The fishing line for the trimmer is wound on the coil, it is inserted into the bobbin, while the 2 ends of the wire remain free. Когда двигатель косилки начинает работать, шпулька вращается, трава срезается свободными концами лески.

How to use a trimmer correctly

Garden trimmers for grass are effective. Newchers think that it is easy to work with a lawn mower, because you just need to include it in a socket or pour fuel, but this is not entirely like that.

The efficiency of the garden tool and its service life directly depend on operating conditions. Therefore, before using a trimmer for grass, you need to perform preparatory work.

The lawn with which you need to mow the grass is carefully examined. Be sure to remove glass and large stones. Having flew out from under a working mower, they can injure a person. They remove the wire from the lawn, because it can be wound on a rotating element, break a mower.

After that they move to the installation of the cutting system. There are trimmers for low.power grass on sale, which use only a fishing line for a trimmer. It is designed for mowing juicy and soft grass. But there are models with a capacity of more than 1 kilowatts on which metal knives are installed. They cut sowing and other hard weeds, trim the young shrub.

In order to replace the cord with knives, you need to unscrew the mounting nut, install the cutting element. Then the nut must be returned to the place, tighten it with the key.

The operator must take care of his safety. Mow grass in tight protective clothes. Special glasses are used to protect the eyes, they will protect from dust, grass and flying garbage. Hands are covered with gloves.

The electric trimmer for the grass is included in the network, and the battery models are charged for several hours before starting operation. Fuel is poured into a gasoline mower.

The mower is kept so that the spool or knife is located parallel to the ground. When the tool is installed in the correct position, the motor is included. After the grass is bewildered, the mower is turned off.

First start

Before the first launch, the operator collects a mower, the procedure is described in the instructions that are attached to the product.

If the trimmer for the grass is gasoline, it is necessarily checked before operation. The fuel tank is filled along the neck.

The motor should work for the fuel, so at the first launch it should work for several minutes without load. After that, start mowing grass.

How to refuel a benzotrimer

Motokos working on gasoline are with two.stroke and four.stroke engines. The first option is much more common. What are the differences between them:

• in trimmers with a 2-tact engine, the response to press the inclusion lever is faster (for this reason the lawn mower is mainly equipped with this type of engine);
• A tool with a two.stroke engine will be much easier, as well as easier to maintain;
• Fuel consumption in a two-stroke engine is higher than in a 4-stroke with a similar power by about 30%;
• The 4x-stroke engine is more environmentally friendly, since the fuel in it burns completely and is not thrown into the atmosphere, as well as its noise level is much lower;
• And the most important distinguishing feature is the refueling: a 2x-stroke engine is equipped with one common tank, where gasoline mixed with butter is poured; 4x-tacte has a separate gas tank and a tank for motor oil.

For refueling, it is necessary to use fresh gasoline AI-92 or AI-95 and high-quality motor oil for garden equipment (for 2x- and 4-tact engines, manufacturers produce different oil). Oil can be used mineral, semi.synthetic or synthetic.

The proportion of gasoline and oil for trimmers with a 2x-tact engine can be found from the instructions for a specific model. Usually it is 50: 1, in some cases, proportions of 25: 1 or 40: 1 are recommended. Prepare the fuel mixture in a separate container with accurate observance of proportions. Never pour the liquids “by eye” directly into the tank without mixing them in advance. Detailed instructions for mixing a benzomalam, with video and description, can be found on our website here.

Running

Before starting operation, gasoline braids are necessarily rolled up. The operator turns on the motor, he must work for a while at idle. It is necessary to ensure that the engine does not overheat, the load should not be.

When running in, motorcycles increase the load gradually. If you start work with high speeds, the motor will work well, this will affect the further work of the mowing.

At the first launch, you should not fully develop a temporary resource. After the engine works at idle, you can proceed to processing the lawn. The lawn mower should operate for no more than 15 minutes, after which the engine is turned off, it must cool down.

If you need to run the electrimmer, the braid is first collected. Then make trial launches at least 3-5 times. If the engine works well, go to mowing. At first they work for no more than 5 minutes, then the duration of work is gradually increasing.

How to wear a belt

If the tool has a shoulder mount, before starting work it hangs on the shoulder. The trimmer for the grass is fixed on both shoulders if it has a backbone mount.

The model with a bicycle handle is held with 2 hands, the D-shaped handle is wrapped in palm. The belt must be worn so that it is convenient, then the back will not get tired.

How to cut the lawn so that it turns out to be even

So that the grass on the lawn is trimmed evenly, it is necessary to lower the mower as low as possible during operation. The site must be divided into squares. You need to work, moving clockwise. In this case, the hay will always lie on the left without interfering under the feet.

Kosim under hay

It is better to mow hay not with a fishing line, but a metal disk. Grass is cut under the root, maintaining its length as much as possible.

Spinning high grass

If you need to mow high grass, this is done in several suits. The lawn processes 2-3 times. The rotating part is lowered from top to bottom, in which case the grass is not wound on the reel.

The operator must remember that the grass wound to the coil leads to overheating of the motor. If this happened, the motorcycle is turned off, and the coil is cleaned.

Most effective mow grass with the ends of the fishing line, and not the entire length. In the second case, the tool works worse, engine overload is possible. If you need to cut the grass on the site of a large area, to increase the efficiency of a trimmer for the grass, you must be tilted towards the mowing.