Trimmer for grass gasoline Husqvarna stalls at low speeds. More complex reasons for the refusal of the lawn mower

Carburetor Husqvarna 128r Carburetor adjustment

The choice fell on this model, as I heard a lot of good reviews about the Husqvarna brand. He has a chainsaw Husqvarna 142. very satisfied. Husqvarna 128r chose as the most popular on Yandex market. Bought in early May 2010. I used it five times with pleasure. Then in mid.August went on vacation. After a month and a half, downtime did not start. Did not bother. There were about 0 degrees at night. I decided that next spring everything will work itself. And here is the middle of June 2011, and my lawn grass is above the belt on the site in general overflows gasoline. the candle all the time is wet. I took from the cottage to the official service at a company store in Khimki closed for reconstruction. Turned to the office. Service on the street. Vasily Petushkova After visiting this service, the desire to leave a trimmer there for the grass for repairs disappeared there. located in the utility room of the store. They refused to regulate the carburetor with me. A lot of broken equipment. The queue will reach no earlier than 10 days. announced. for adjustment. 1000, for a new carburetor (just buy them and put it yourself). 2600 but press that it may be necessary to replace the piston 6000. 7000 spare parts for the carburetor. Disassembled at home. Zama carburetor Model C1Q-W41. By the nature of the malfunction (gasoline flows even with a non.working motor through the carburetor and further through the air filter) Most likely problems with the needle valve. You can’t buy spare parts anywhere. Only a carburetor assembly (3000). I dismantled the carburetor, cleared everything with a special spray for the carburetor. Collected. the same picture covered a bunch of sites on the Internet. Most of the Carburetor of this type (VALBRO) on the paraplaner player carburetor. There, the guys are clearly versed with needle valves and springs (the filling of the carburetor camera depends on the rigidity of the spring with gasoline), the spring slightly stretched out, collected it “Oh miracle. “After a little adjustment, I worked out like a clock for half an hour. Two weeks later, to the country and Again the same picture of a carburetor overflow. Starts with a closed damper and then stalls. It turns out without a new locking needle of the carburetor and the springs (there are less than 50 spare parts for cars) my braid for grass. scrap metal. As a result, I ordered Zama RB-47 Carburetor Kit Zama RB-47 Carburetor Zama at Ebay.com “. Marasmus. Services do not sell, in the markets. no. On the Husqvarna support telephone, the dispatcher can only say information on the website on the site, t.e. They are politely sent to official services as a result I am waiting for a carburetor remote assembly from America, and the grass is not a kosen!

By purchasing a gas pump, you must be prepared for the fact that, like all other similar tools, it can also cause failures that require repair.

Nevertheless, do not immediately go to the service center and pay a lot of money to the owners, convincing you of a serious malfunction of the device.

Gasoline stops at high gas speed

Perhaps the most common complaint related to gaskets of gasoline knitwear sounds like this: “gasoline kiosks”.

Of course, this can be caused by a rather serious malfunction. However, most often the situation is much simpler than it seems at first glance.

To cope with this problem, first of all, try to understand its reasons yourself, in the end, finding out the reason, it is much easier to fight the problem, and sometimes even self.destructive.

In fact, the reasons for this, when gasoline is at high speeds, there are many reasons.

Others are the presence of malfunctions in the energy system.

Husgvarna 540. Механическая газонокосилка. Стоит ли переплачивать? Обзор.

In this case, gasoline will be idle. Problems with a power supply system can lead to a displacement or incorrect tuning of a carburetor.

What to do if the Husqvarna 128R mower is not gaining momentum and kiosks

When adding a gas. trimmer for grass does not pull. When loading, a trimmer for grass loses speed.

The gas mowing gas is a gas throat when a trimmer for grass nods when a throttle

Vibration can be caused by vibrations that occur during the operation of the gasoline bucket.

Incorrect adjustment of the gasoline pump can be fixed by simply adjusting it in accordance with the requirements specified in the operating instructions.

In addition, sometimes gasoline trimmers for grass can stop, because the valve located in the gas tank cover simply clogs or gets stuck.

To find out, try to use the braid, loosening the fuel tank cover.

If the device works correctly in this mode, clean the valve.

In addition, gasoline may stop due to poor fuel supply to the carburetor

Why then the device begins, ask you?

The reason for this is that at first the fuel gradually gets into the carburetor, and this is enough to work with increased power.

However, then it is produced and at high speeds the engine begins to stop.

As for the carburetor, the problem here may also be that its case is too tight.

The reason that gasoline is at high gas speeds can also be absorbing air.

We are talking about the possible presence of the place through which air can pass through the engine heating.

Among other things, do not forget to check the fuel supply hose. The problem may be that it is slightly held or even crack.

These are the main reasons why gasoline may stall.

Why the chainsaw is not started

If defects occur, it is necessary to check the serviceability of the components.

If a new chainsaw is not started, you should check the presence and supply of fuel, the occurrence of a spark on the spark plug, the functioning of the exhaust valve, the condition of the filters. The work of a saloon stalling device built into the fuel cover of a stalling device.

The reason that the Chinese chainsaw is not started can be poor.quality equipment. It is possible to have various malfunctions, incorrect assembly. Some goods come to defective. If the inspection has not revealed malfunctions that can be eliminated independently, you can replace the saw on the warranty coupon.

trimmer, grass, gasoline, husqvarna, stalls

On the cold

The reason why the device does not start on the cold is often a violation of the sequence of engine start.up.

You should familiarize yourself with the instructions: manufacturers indicate how to properly launch a chainsaw.

To enrich fuel, you should first close the air damper. After that, fuel suction is produced. For this, a special primer is used. Then turn on the ignition. Until the first outbreak of engine, several starter movements need to be made. The damper opens, the device is launched. If the sequence is violated, any step is missed, incorrect work is possible.

If the chainsaw has stopped starting, the probable reason is the problem with the fuel system. Non-varnishes with launch can occur due to an incorrectly adjusted carburetor, clogging of the highway and the fuel filter. The quality of fuel is also important. If the fuel is diluted with water, the device is poorly started or does not work at all. The mixture should be fresh.

Read also: Soldering aluminum air conditioning tubes

A possible cause of problem launch is engine malfunction. Wear or breakdown of the part leads to undesirable consequences: reducing compression in cylinders and other troubles. It is recommended to contact specialists with such problems, since it is difficult to diagnose and fix the breakdown independently.

Hot

If the chainsaw is poorly started to be hot, you should start an inspection of the tool from the spark plug. It will also be required to check the spark on the candle.

So that the device works properly must be a dry candle. When it is wet, there are no sparks on the contacts. You can try to replace the part with a new.

If there is a spark and the candle is in good condition, try to look for a problem in the fuel system. If, upon visual inspection, it was not possible to detect the cause of the breakdown, the carburetor should be removed. If the amount of fuel exceeds the permissible, the device will not work. The candle should be wet. Should turn the candle hole down down. If the fuel mixture is pouring, the reason why the chainsaw is not started on hot, there will be an excess of fuel.

The reasons

Trammers for grass are reliable and durable (of course, subject to proper care). Most often, malfunctions arise due to contamination of structural elements.

If the engine of your lawn mower does not start, does not gain momentum, does not reach the power you need or suddenly stalls, it may be a reason:

  • low.quality fuel (fuel mixture), it can be in long.term storage or in non.compliance with the recipe for the preparation of the mixture;
  • The grass was wound on the shaft of the fishing/knife head;
  • clogging of the air filter/muffler;
  • Balance of the carburetor.

Ways to eliminate problems

The first three reasons are quite simple to eliminate. If the matter is the mixture, it is necessary to pour old fuel from the tank, prepare a new emulsion from high.quality gasoline and engine oil (if your motor requires a mixture) and pour it into a fuel tank. If a trimmer for grass works on clean gasoline, it’s still easier.

In the second case, it is necessary to carefully release the details of the trimmer for grass from the wound grass.

If the filter is clogged, you can try to rinse it. If this procedure has not brought the effect, replace it with a new.

The last reason why the lawn mower does not work properly will require you a little more knowledge and skills.

In order to properly adjust the carburetor of the lawn mower, it is necessary to observe a certain procedure. First of all, carefully clean the air filter. The easiest way to rinse it (it is advisable to carry out the filter with water regularly after 9-10 hours of operation).

After that, in the diagram of your trimmer for grass, which is in the instructions for the operation of the device, find the adjustment screws. Usually there are three of them: the first is responsible for the supply of fuel, the second. for idle, but the third is designed to limit the number of maximum engine speeds.

Next, you should turn on the unit and wait for the engine to warm up.

Slowly twist the first adjusting screw (fuel mixture). Catch the moment when the motor begins to stall, and turn the screw in the opposite direction 45 degrees. If you did not have time and the motor stalled, the screw should be turned 90 degrees. Open the throttle and see how the speed is going. Next, you should slowly unscrew the screw (each turn. the same 45 degrees) until the moment when, with full gas, the motor begins to firmly issue maximum revolutions.

The second screw, as mentioned above, controls the engine speed at idle. Weakening it, you reduce the number of revolutions, tighten. increase. The screw must be adjusted so as to ensure confident operation of the motor at small speeds. Accelerate the engine for better starting a little. At the same time, make sure that before the movement of the knives/coil with the fishing line, the motor makes several dozen revolutions. With poor starting the engine, screw the screw slightly.

After you have adjusted the first two screws, test the operation of the device at the maximum engine speed. If necessary, you can limit it (maximum). this will serve as protecting the motor from “boiling”. To do this, you need to do the third screw. Unscrew the fixation nut until the moment when the control screw can be calmly turned. To increase the maximum speed, the screw must be loosened to reduce. on the contrary, tighten. Fix the screw position with a nut. Test the work of the motor again.

Spend the position of the screws regularly. a high level of vibration characteristic of benzocoses can cause their involuntary shift.

Remember that carburetor adjustment is not the final procedure. During operation, Motokos, most likely, you will have to mess with it more than once, because an unbalanced carburetor is both an increased fuel consumption and a quick failure of the candles, not to mention reducing the power and productivity of the device.

Main reasons

The following reasons are possible why the lawn mower or trimmer for grass stalls when trying to re.start and continue the interrupted work:

  • malfunctions in the engine;
  • refusal to supply gasoline and oil;
  • damage to pipelines (capillaries, hoses, pipes);
  • malfunctions in the ignition system.

General description of problems with a scythe or trimmer is not enough here. Clear and immediate repair, high.quality maintenance is impossible without specifying the identified cause.

With gazeaming

You click on gas. and the trimmer for the grass stops working, does not develop momentum. The following alleged reasons are possible:

  • The tuning of the carburetor was lost, which appears with an increasing load on the drive itself. after its long downtime or when working in extreme conditions;
  • The fuel valve is clogged with deposits;
  • The carburetor cable is weakened and sag;
  • Excessively stretched, possibly torn off the fuel supply hose;
  • The check valve (sapun) clogged with deposits. fuel does not enter the tank with fuel.

Important! Problems in the carburetor itself give themselves out the vibration of the lawn mower.

With an increase in speed

If the lawn mower (or a trimmer for grass) has stalled when the engine speed is added, check the device according to the following signs:

  • clogging or sticking a valve built into the gas tank cover;
  • valve adjustment violation;
  • A failure in the work of pistons and cylinders. from vibration during the work of a braid for grass or a trimmer for grass, random blows directly in the session of the mowing of grass;
  • violation of the supply of fuel mixture;
  • excess air pumping into the motor;
  • cracking of the fuel intake hose, weakening its compounds.

When the fuel.heating mixture is served with the right portions to the engine in a timely manner. it burns the amount that has managed to enter from the moment of the last gallpling, and he stalls again.

When working idle

Having launched a trimmer for grass or a motorcycle at idle, you find that the device is starting up. but it swallows, after working, say, 5-10 minutes. The reasons here may be as follows:

  • clogging, violation of carburetor adjustment;
  • Initially incorrect configuration of the valve mechanism of the carburetor;
  • air filter clogging;
  • reducing the speed of the gearbox (if any). the incorrect ratio of the fuel mixture;
  • clogging the throttle;
  • penetration of excess air into the fuel system;
  • The fuel ends in the tank (and oil in the tank, if the engine is four.stroke).

If there are problems directly with the carburetor, the machine will stop both after a cold start and after launch on the already worked engine.

Immediately after the start

The stalling of motorcycles or a trimmer for the grass immediately after the start is due to the following reasons:

  • impressive of previously adjusted valves;
  • Initially incorrect setting of the valve mechanism;
  • clogging with fuel supply valve;
  • the hose is worn or poorly attached.

Due to the violated fuel injection algorithm, a lawn mower or a trimmer for grass is greatly vibrated in work.

In the process of warming the engine

If the engine heats up too fast, overheating. a lawn mower or a trimmer for grass works unevenly, as if jerking. After which she stalls. The reason may be as follows:

  • boiling gasoline;
  • The ignition wire was damaged (poor insulation);
  • The coil in the ignition system has noticeably burned out, inter.seal circuits appeared.

The same heating is observed when using rotary (not disk) damper.

When opening an air damper

A lawn mower or a trimmer for grass stalls when raising the damper for the following reasons:

Ways to eliminate breakdowns

The following works are possible by carburetor:

  • cleaning and adjustment of the fuel supply valve;
  • similar work with a valve producing spent gases and pairs (after fuel burning);
  • replacement of the spring weaker on the entrance valve;
  • restoration of the tension of the carburetor cable;
  • replacement of the fuel leaks hose, verification and strengthening of a weakened connection;
  • changing the rotor damper disk;.
  • Change of faulty wire or ignition coil.

The list of work on the work may also include the cleaning of the nozzles (in a 4-stroke engine), replacement of the valve washer, gaskets in tanks and so on.

The gasoline trimmer for the grass starts and stalls

Why is a trimmer not starting for grass gasoline? Reasons and their elimination

Recently, a gasoline trimmer for grass has acquired the status of one of the main tools in the arsenal of summer residents. And this is not surprising, because a motorized braid for grass allows you to quickly put a personal plot in order. However, sometimes it happens that the trimmer for the grass does not start hot and even on cold. In such situations, you have to independently establish the cause of the malfunction. Let’s find out what to do if a trimmer does not start for grass. The reasons that most often lead to such troubles will be considered further.

Diagnostics strategy

Where to start the diagnosis of malfunctions if a trimmer is not started for grass? In situations where the tool stalls immediately after starting, it is worth examining the following units:

It is the breakdown of the above locations that most often leads to the fact that a trimmer for grass is poorly started. Let’s look at how to eliminate such troubles.

Checking the fuel mixture

Suppose you don’t start a trimmer for grass. In this case, the first thing is to check whether the fuel is enough in the tank, as well as evaluate the quality of the fuel mixture. To refuel a motorized unit, it is necessary exclusively high.quality gasoline. It is recommended to use fuel, the brand of which is not lower than AI-95. Refueling a trimmer for grass with fuel of unknown origin, not bought at a gas station, is fraught with frequent failures in the work of the tool. This can cause a breakdown of the cylinder-piston system. Repair in this case often exceeds the cost of the device itself.

Why is a trimmer not starting for grass gasoline? Incorrect preparation of the fuel mixture may also lead to this, which consists of oil and gasoline. The proportions in which the specified components are connected are indicated by manufacturers in the guide for the operation of a trimmer for grass. Preparing the fuel mixture is extremely not recommended in large volumes, that is, for the future. Indeed, with prolonged savings, there is a loss of the determining properties of the substance. Therefore, if a trimmer for grass does not start, it is worth draining the old fuel and use freshly prepared fuel mixture.

Read which trimmer for grass is better than rotary or vibration

Установка катушки Stihl на косу Husqvarna

Diagnosis of the candle channel

What to do if the used fuel mixture is in perfect order, but a trimmer for grass is still not started by gasoline? The reasons for the refusal of the mechanism may lie in excessive moisture of the candle channel. To diagnose and eliminate the problem, it is necessary to do the following:

  • To twist the candle. Wipe it thoroughly, and then dry it.
  • Drain excess fuel in the chamber through the corresponding candle hole.
  • Clear the old candle if there is a dozen on its surface. Cope with the task will allow the use of a conventional ladies’ nail file or file.
  • When installing the element in place, set a gap of 1 mm. To check the parameter, it is enough to place any coin in the lumen.
  • Collect a functional block back.
  • Try to start a trimmer for grass.

It is recommended to perform a candle channel to dry for at least half an hour. However, in no case should you resort to the calcination of its elements. After all, heating the spark plug can lead to its final corruption. Что предпринять, если обслуживание функционального блока было выполнено в соответствии вышеуказанным рекомендациям, но триммер для травы не заводится, искра есть при этом? In this case, it should be treated with gasoline threaded connection. The latter does not need to be saturated abundantly fuel. It should only be slightly moisturized. Resort to such actions should be to ensure the ignition. After all, no matter how much the candle gives a strong spark, in an absolutely dry chamber there simply will not be something to ignite.

The lawn mower stalls

Carburetor adjustment, well start

,stalling when pressing gas. My Skype: Ork.Vitek tel. 380979677418

The lawn mower stalls or suffocates when you press the gas

Even more information about the repair and choice of tools on our website www.Looktool.Ru, we are happy for everyone.

If even in this case a trimmer for grass does not start, it is worth evaluating the quality of the contact between the high.voltage wire and the candle. In the absence of a spark (in the presence of a reliable connection between the indicated elements), most likely, the problem is caused by breakdown of the ignition unit. In this situation, you will have to turn to the services of masters who will reinstall the knot.

Checking filters

Another common cause, due to which a trimmer for grass does not start, is the presence of a blockage in the filter area. To confirm the conjecture, just dismantle the indicated block and try to start the unit without it. If the engine of the trimmer for the grass has launched, most likely you will have to replace the air filter or at least perform a thorough purge of the old. In the presence of abundant contaminants on the surface of the filter element, it is necessary to use a new grid. Relying to such actions, you should not leave a suction pipe at all without a filter. After all, rush in this case can lead to the need to repair the entire piston group of the unit engine.

Cleaning the soundtress

Often the engine of branded models of trimmers stalls as a result of clogging of the soundtress. The main task of the specified component is to align the pressure in the fuel tank. In the case of contamination of the node, a vacuum is formed here, which significantly complicates the supply of fuel. Eliminating the malfunction allows the cleaning of the saapon using a conventional sewing needle.

Diagnosis of the graduation channel

The stable functioning of a trimmer for grass can be impaired as a result of laying dirt in the graduation canal or the formation of a blockage on a muffler grid. This problem most often occurs during the operation of older generation trimmers. The issue is being solved by dismantling the anti.diploma mesh and its cleaning.

How to prevent sudden breakdowns during the operation of a trimmer for grass?

So that the unit is always in a functional state, it is worth observing several simple rules:

Preventive measures and operating rules

So that the lawn mower does not work and does not stall when starting, it must be correctly stored and operated. Compliance with the following simple recommendations will forget about problems.

  • When begging the grass, you need to monitor the state of the cooling system. It is also necessary to regularly clean the channels in the case and starter’s ribs.
  • To clean the tool, you should use kerosene, solvent, or other washing tools.
  • You can not clean a hot tool. it must cool before washing.
  • It is important to observe the recommended working mode. this will avoid overheating of the engine.

To store the tool in cold weather, you need:

  • completely drain the fuel;
  • disassemble the lawn mower, wash and clean all available components;
  • inspect the condition of the parts, eliminate all defects that can be corrected;
  • pour the required amount of oil into the gearbox;
  • Clean the air filter;
  • perform partial disassembly of the engine, wash all moving parts, blow and lubricate thoroughly;
  • To lubricate the piston, unscrew the candle, then raise the piston to the upper dead point by the starter, pour a small amount of oil into the hole for the candle and do the crankshaft several times.

Important! If there is no way to store a trimmer for grass in a warm dry room, you must first wrap the motor with an embarrassed rag.

Only by observing these rules, you can be sure that the lawn mower will work properly and will not stall for a number of seasons.

As you can see, stopping the work of a trimmer for grass can be caused by many reasons. Most of them can be fixed independently using the user instructions. In cases where there is no self.confidence, the equipment is recommended to be attributed to repairs. It is worth remembering that incorrect actions can cause even greater harm to the trimmer. As a result, the repair of Motokos will cost a much larger amount than it would be initially, and in the worst case, it may be necessary to buy a new unit.

Why stalls the lawn mower: reasons and solutions

The reason why your tool abruptly stops working, namely the engine does not gain revolutions, breaks them off, or “stalls” in popularity, there may be more than one. Often this is to blame not only the engine itself, but also the adjacent systems, unit nodes, completely different details related to the preparation of the fuel-air mixture, its quality, transportation to the tool of the tool. Consider the most typical situations:

  • He is not gaining momentum. The engine drive mechanics may be damaged or there were problems with the carburetor, but the main reason should be considered clogging of the air filter. To change the situation, it must be removed, cleaned, and if it is no longer subject to the latter, then change for a new one, promptly making an order on our website. Also, there will not be a turn of the braid for grass, if the cable from the carburetor constantly flies. disassemble the unit and firmly fix it, or buy a new one if cracks are found on the element, other types of deformations.
  • At high speeds. The lid on the gas tank is clogged. it needs to be cleaned or new. often the reason is a sipped carb. We submit information on the correct adjustment of all screws in information articles. Check the quality of the fuel hose and change it to a new one if necessary.
  • When heated. It occurs in moments when the fuel in the carburetor literally boils. It can also appear in the options if the carba damper is more rare, rotary type (not disk). The only option would be to replace the carburetor with a new. There is another option for a broken wire or ignition coil. In this case, change the element of the latter.
  • Starts and stalls (immediately after launch). Solved or incorrectly adjusted carburetor is the main reason for this situation. Calm vibration will indicate an uneven supply of fuel, and competent adjustment of the node will help to correct the situation.

We hope you found the right answer to the question: why the lawn mower stalls, and all the proposed catalog details today, as always, are at your service. You need a piston trimmer for grass, a new carburetor, or the elements accompanying the operation of these systems. you will find everything in the open spaces of the Benzo SIP store.

What to do if the lawn mower stalls when you press the gas

Most often during the periods when the lawn mower stalls when the gas is added, the cause will be the air damper, more precisely, its condition: it clogged. Structurally, the part is located in the place where the resulting fuel is sprayed behind it, and, accordingly, the product collects all inclusions in low.quality gasoline. To eliminate the problem, you just need to clean it. The same situation can occur with a filter clogged, but it is eliminated similarly. Total, we specify the reasons for which the tool is led to the gas to the stalled state:

  • a clogged air damper;
  • The clogged filter is fuel, and when you give gas, this is especially noticeable;
  • the air of the crankshaft shaft occurs;
  • damaged gasket between the cylinder and the carb.

When you cleared, washed and blowing the elements, but again the lawn mower stall when you press the gas-replace them with new ones, check the quality of the fuel, as well as the literacy of the proportions of the cooked mixture. When opening the air damper, the tool will stall for the following reasons:

  • Dosage carburetor.
  • The appearance of cracks on the fuel hose caused air leaks.
  • The occurrence of problems with the oil seals.

In the process, situations arise when the lawn mower at high speeds is subject to a similar sharp stop. It occurs for the following reasons:

  • due to problems with the circulation of the fuel mixture;
  • with air leaks;
  • The fuel intake hose is poorly connected or cracked and cannot be used;
  • stab or clogged the valve of the cover of the gasoline tank;
  • The carburetor was resolved.

In most cases, nevertheless, the cause will be a carburetor and related filter, hoses. If you need cutting gear or trimmer heads, then our site will also offer them to buy them with gasoline tools and components for them.

The trimmer for grass stalls. how to eliminate the problem

A gasoline trimmer for grass is a useful tool for cleaning from unnecessary grass of house territories and large area lawns. The design of this technique is quite complicated, therefore, if the device breaks, there may be several reasons. The most likely factors that have caught a breakdown are usually described in the user guide. Knowing why a trimmer for grass stalls, you can try to independently eliminate the defect. The most common malfunctions provoking the motorcycle stops, and the ability to repair them with your own hands is in the material further.

In order to most accurately determine the cause of the trimmer malfunction for grass of any brand (for example, echo) and find out the possibility of eliminating it, you need to install, when performing what action the device stalls. The engine can turn off both at idle and at high speeds, heated under load or immediately after starting and t.D.

If you stalled after gas supply

Owners of gasoline braids often mention that the lawn mower stalls when you press the gas. Usually such a breakdown occurs due to problems in the carburetor. A failure in his work can occur due to long-term storage, use in difficult conditions, significant overload of the motor. The symptom of such a breakdown will be vibrating movements of the device during operation.

On a note! Users familiar with the repair of a car carburetor can try to restore this important node of the trimmer for the grass on their own, using the instructions for operating. Otherwise, the correct decision will be to seek help from the service center representatives.

Sometimes a trimmer for grass stalls when you give gas because the fuel valve is clogged. This interferes with the supply of gasoline. To eliminate the problem, it is enough to loosen the valve. Thus, normal supply of carburetor fuel will be restored.

Another possible reason why the lawn mower stalls when gas is supplied is pollution of the soundtress (check valve). This detail prevents the appearance of a vacuum in a gas tank. If it is clogged, the air does not flow, which means that fuel does not go to the carburetor. To eliminate the problem, it is necessary to clean this element.

If it stalled at high speeds

If the carburetor stalls at high speeds, this means that in idle and small there are enough incoming fuel, and to work on high is not enough. Then it is necessary to check the serviceability of the following nodes of the trimmer for the grass.

  • Fuel hose. its integrity could be violated as a result of cracking. In this case, you need to replace the part. Or maybe you just need to tighten the clamps.
  • A filter network between a carburetor and a hose for supplying a gasoline mixture-it could clog. In this situation, it is necessary to clean the detail.
  • The valve on the gas tank cover. he could stick or clog with garbage. Cleaning is also necessary.
  • Carburetor. perhaps as a result of constant vibration, it was resolved. This is usually characteristic of cheap Chinese details. To eliminate the problem, it is necessary to set up according to the instructions. In some cases, it is enough to only weaken the tightening of the carburetor case. If the adjustment is not possible, it is necessary to install a new element.
  • Additionally, check the air filter. Perhaps it will need to be washed and cleaned or replaced with a new one, as he could clog with dirt and particles of grass when tilted technology, when the user mowed in hard.to.reach places.

If you stalled during work idle

If the lawn mower stalls, working idle, there may be several factors reasons.

  • First you need to check the prepared fuel solution, when it comes to a four-stroke trimmer working on a gasoline-oil mixture. There is a chance that it is made incorrectly. the proportions are not withstanded. Because of this, the gearbox is warming up, and the revolutions on the drum are lowering.
  • Another probable cause is blockage of elements such as a throttle, air filter or carburetor. You need to clean the indicated details.
  • Another possible factor is to resolve or incorrectly carried out carburetor adjustment. You need to adjust the setting according to the instructions.
  • Observe this problem mono and when opening the air damper. In this situation, the lack of fuel for a trimmer for grass occurs through the fault of the air flow.

If the device does not have enough fuel, it works properly at high speeds or when they increase, but stalls at idle. If the root of the problem consists in the carburetor, the lawn mower will be disconnected both with cold startup and hot.

If you stalled after starting

If the technique starts and stalls immediately after starting, this indicates the wrong settings or deducting the device. As a result of this, the fuel enters the engine unevenly, which leads to significant vibration and disconnecting the trimmer for the grass. To fix the breakdown, it is necessary to reconfigure the device according to the user management.

Another probable problem is the blockage of the valve supplying the gasoline mixture. It must be cleaned.

On a note! If the trimmer for the grass starts, but immediately stalls, it may also mean that the fuel is moving to the carburetor with difficulty. Weakening the valve will help to eliminate the problem. this will provide uniform and free circulation of fuel in the device.

Another possible reason is the damaged fuel intake hose. Air can penetrate through cracks and holes into the system. To solve the problem, you need to increase the engine speed in order to get rid of air bubbles that have penetrated the device.

trimmer, grass, gasoline, husqvarna, stalls

If you stalled when opening the damper

If the technique works properly at idle, but stalls when opening an air damper, this reports about the penetration of air into the system through cracks in the fuel supply hose or damaged oil seals. To fix the breakdown and establish the work of the tool without driving air from the atmosphere, it is necessary to replace damaged parts.

Preventive measures and operating rules

So that the lawn mower does not work and does not stall when starting, it must be correctly stored and operated. Compliance with the following simple recommendations will forget about problems.

  • When begging the grass, you need to monitor the state of the cooling system. It is also necessary to regularly clean the channels in the case and starter’s ribs.
  • To clean the tool, you should use kerosene, solvent, or other washing tools.
  • You can not clean a hot tool. it must cool before washing.
  • It is important to observe the recommended working mode. this will avoid overheating of the engine.
  • If a braid for grass is not used over the next thirty days, the fuel must be drained, otherwise it will fall into heavy components that can score the channels of the carburetor.
  • After the fuel is merged, the trimmer for the grass should work at idle for some time until it turns off. This will allow you to completely get rid of the rest inside the working mixture.

To store the tool in cold weather, you need:

  • completely drain the fuel;
  • disassemble the lawn mower, wash and clean all available components;
  • inspect the condition of the parts, eliminate all defects that can be corrected;
  • pour the required amount of oil into the gearbox;
  • Clean the air filter;
  • perform partial disassembly of the engine, wash all moving parts, blow and lubricate thoroughly;
  • To lubricate the piston, unscrew the candle, then raise the piston to the upper dead point by the starter, pour a small amount of oil into the hole for the candle and do the crankshaft several times.

Important! If there is no way to store a trimmer for grass in a warm dry room, you must first wrap the motor with an embarrassed rag.

Only by observing these rules, you can be sure that the lawn mower will work properly and will not stall for a number of seasons.

As you can see, stopping the work of a trimmer for grass can be caused by many reasons. Most of them can be fixed independently using the user instructions. In cases where there is no self.confidence, the equipment is recommended to be attributed to repairs. It is worth remembering that incorrect actions can cause even greater harm to the trimmer. As a result, the repair of Motokos will cost a much larger amount than it would be initially, and in the worst case, it may be necessary to buy a new unit.

Low quality fuel use

The benzotrimer does not gain speed in case of poor.quality fuel. He may stop or not start at all. To check the quality of the fuel, you need to inspect the candles. They are the main indicators for solving problems with the combustion chamber.

In the presence of sediment, a raid, plaque, the old fuel merges, and another, high.quality.

or gasoline cutter should be filled with good quality gasoline and the fuel brands that the manufacturer indicated in the technical passport of the device.

For your information! Candles should be thoroughly cleaned of plaque, and only after that they are again placed in the combustion chamber.

What to do if a benzotrimer is not gaining momentum

If you once purchased a trimmer for grass, working with gasoline, then you probably had to face the problem of turning on a trimmer for grass, as well as a problem as a benzotrimer does not gain momentum

That is why this article has been created.

So, what to do if a trimmer for grass, working for you for several years, suddenly just stops gaining momentum

, and the motor is simply stalling? In this case, you and I should consider a number of problems related to stopping the work of the motor.

The motor may stall under various circumstances. The lawn mower does not develop speed, the reason. | Funnycat.TV. Sometimes the reason for the incorrect operation of the trimmer for grass working from gasoline is the clogging of the air filter.

It is the filter that is one of the most important reasons why the operation of a gasoline trimmer for grass may stop

Various garbage very often gets into it, particles of dust that also clog the filter, so it needs to be cleaned and washed every month, and maybe more often, it all depends on what power the gasoline trimmer has for the grass, as well as then how often do you use this device.

At idle

At single speeds, the common reasons for stopping a trimmer for grass are as follows:

  • reducing the speed of the gearbox when heating it, which is a consequence of the use of inappropriate fuel mixture;
  • clogging of the throttle;

If a carburetor is a problem place, then the technique will stop at the “cold” and with a “hot” launch.

Preventive measures and operating rules

So that the lawn mower does not work and does not stall when starting, it must be correctly stored and operated. Compliance with the following simple recommendations will forget about problems.

  • When begging the grass, you need to monitor the state of the cooling system. It is also necessary to regularly clean the channels in the case and starter’s ribs.
  • To clean the tool, you should use kerosene, solvent, or other washing tools.
  • You can not clean a hot tool. it must cool before washing.
  • It is important to observe the recommended working mode. this will avoid overheating of the engine.

To store the tool in cold weather, you need:

trimmer, grass, gasoline, husqvarna, stalls
  • inspect the condition of the parts, eliminate all defects that can be corrected;
  • pour the required amount of oil into the gearbox;
  • Clean the air filter;
  • perform partial disassembly of the engine, wash all moving parts, blow and lubricate thoroughly;
  • To lubricate the piston, unscrew the candle, then raise the piston to the upper dead point by the starter, pour a small amount of oil into the hole for the candle and do the crankshaft several times.

Important! If there is no way to store a trimmer for grass in a warm dry room, you must first wrap the motor with an embarrassed rag.

Only by observing these rules, you can be sure that the lawn mower will work properly and will not stall for a number of seasons.

As you can see, stopping the work of a trimmer for grass can be caused by many reasons. Most of them can be fixed independently using the user instructions. In cases where there is no self.confidence, the equipment is recommended to be attributed to repairs. It is worth remembering that incorrect actions can cause even greater harm to the trimmer. As a result, the repair of Motokos will cost a much larger amount than it would be initially, and in the worst case, it may be necessary to buy a new unit.

The spring may interfere

My first attempt to adjust the gas mowing carburetor did not give anything, since the spring of the fuel mixture adjustment propeller prevented. The factory spring turned out to be too thick in a compressed state and did not make it possible to reduce the supply of fuel to the required level. I had to choose another spring and continue the adjustment after its replacement.

The adjusting screw for feeding the fuel mixture with the spring

In the photo above the factory spring, below the adjusting screw with a selected spring. I am writing about this, because I am not sure that this is an isolated case, and someone else may face the same situation.

From personal experience

lawn mower or trimmer for grass

Trimmer for grass is a broader concept than a lawn mower (lawn mower), since it can also be an electric. Gasoline trimmer for grass and lawn mower. This is the same.

Some authors assure that a trimmer for grass. This is a weaker tool, in contrast to a more powerful lawn mower, which can be used to mow shrubs. Personally, I have a tool with a maximum capacity of 1.7 kW and capable, as stated in the instructions, to mow a small shrub up to 10 mm thick. User manual is called “trimmer for grass gasoline. “”.

The proportion of the fuel mixture

I read somewhere that if the law mowing manual and the canister with butter indicates different proportions of the preparation of the fuel mixture, the proportion indicated in the manual should be used.

For a long time he did. Excess oil flowed out of the engine to the gas tank and the fog was constantly formed on the candle, since the leadership indicated a proportion for a running.in engine 1:25, and on the canister. 1:50. After the transition to a proportion of 1:50, the appearance of oil fluxes stopped. The candle continued to burn, but with less intensity (the carburetor has not yet been adjusted).

Until now, some users of the benzo tool determine the fuel mixture “by eye”. If when preparing the mixture the amount of oil is underestimated, after a while an extraneous sound may appear immediately after the engine starts, gradually disappeared during heating, and the engine stop occurs with a sharp jerk. The continuation of the operation of a trimmer for grass in this mode will lead to its failure.

Clead cleaning

In the worst times of the work with a trimmer with an unresolved carburetor, the engine stopped starting after using each fuel tank. And only after cleaning the candle from the car, could you continue to work.

Small sandpaper was used to clean the electrodes, and to clean the space between the insulator and the case. Subtle office paper clip with a bent end. At first, the electrodes were wiped with high dirt with a rag, then cleaned with sandpaper. After that, the candle fell into the diesel fuel and the moistened carpet was opposed by a paper clip from the surfaces of the insulator, the inside of the body and between them. Further, the candle fell several times into the diesel fuel, which then shake off it along with the pollution. Sometimes the procedure for cleaning a paper clip and washing were repeated. After that, the candle wiped dry and was ready for further operation.

Невероятно, но один бачок топливной смеси при неотрегулированном карбюраторе может израсходоваться менее, чем за 10 минут. проверено на практике, когда триммер для травы был запущен и эксплуатировался на высоких оборотах с максимальной подачей топлива (регулировочный винт был откручен намного больше нормы).

You can order seeds of vegetables and flowers, plant protection and microme-sharing products in the online store. Low and good germination on customer reviews. Mail delivery.