Trimmer for grass there is no thrust. What is the reason.

Why is a benzotrimer not gaining momentum and strangle

How not to get confused if the lawn mower does not start, despite its small dimensions, represents a complex technical device. If we study the operating annotation, there will be prerequisites why the lawn mower is not started, known and eliminated. It is necessary to alternately exclude the reasons that make it difficult to start the tool. Why is a trimmer for grass stalls when pressed at high speeds. The lawn mower stalls. They usually start with more affordable nodes with a slight checking check.

Diagnosis of malfunctions

All the prerequisites why the lawn mower is not started can be systematized by the specifics of the operation of individual units. The service center is systematized:

  • Motor malfunction (piston wear, bearing malfunction, crankcase crack);
  • Fuel consistency supply malfunction. clogged pores of an air filter or a malfunction of a carburetor;
  • the ignition system does not work;
  • A malfunction of a mechanical disposition. a leak of hoses, broken wires under a braid, rupture of the tubes.

The user first needs to check if there is a fuel in the tank. Starting in agreement with annotation, putting the saw on the side. Set the air damper to the position “Closed”, pump up fuel, turn on the ignition and produce 3-4 sharp jerks by the starter. If the engine has earned, open the air damper. The lawn mower is not started. we repeat the operations with a slightly open air damper.

The lawn mower cannot work for a long time. Gearbox and engine will overheat. Mowing less than 15 = 20 minutes, taking a five.minute break. In hot noon, the operating time is reduced by half. When mowing weeds, sedgers, the working hours are required to reduce.

If you are unsuccessful, we begin to find the reason for the refusal:

  • check the quality of fuel;
  • make sure the operability of the candle and the cleanliness of the candle canal;
  • check the cleanliness of the air filter;
  • Make sure that the fuel filter is not clogged;
  • Check the cleanliness of the bastard;
  • Clean the exhaust channel.

complex reasons will be detected in the diagnosis of a malfunction, leading to the overhaul of the carburetor. Such reasons include clogging of the internal channels of the carburetor, wear on it gaskets and violation of the tightness of internal halls with a vacuum loss. Why does the lawn mower stall that the reason is why when operating the engine at high speeds. DIY lawn mowing repair, if it does not start, will require patience.

Elimination of the reasons why the lawn mower is not started

The fuel mixture should be prepared with accurate observance of gasoline and oil proportions. In this case, you cannot use another brand of fuel. To exclude dirt, gasoline should stand in a glass or metal dish 2 days. Cannot be used for storage of fuel plastic dishes. Distribute the oil with a medical syringe without a needle. Use only a freshly prepared mixture, without leaving an unexplored fuel in a tank. If the engine is capricious, the lawn mower stalls, when you press gas, it may be guilty of fuel.

Trimmer for grass The lawn mower stalls when adding gas / Benzonase Trimmer Stalls When The Throttle

adding gas. trimmer for grass does not pull. Trimmer for grass loses its turnover with a load.

What to do if the lawn mower or saw stalls at high speeds (under load)

Group for repairing garden equipment Video about the reasons for the sudden stop of a two.stroke.

Other reasons why the engine stalls hot

In addition to the material above, I would like to note a number of malfunctions that lead to a sudden stop of a hot motor when driving. The unit may stall on the go if the belt or timing chain breaks off. This situation means that in most cases, the power unit will require expensive repairs, since the valves are bended as a result of the break, there are defects in the piston and other damage to the engine elements.

If the motor stalled during the passage of deep puddles or other water barriers, then there is a high probability of water entering the cylinders or wetting the elements of the ignition system. In the first case, water enters the combustion chambers through the air intake. Since the water is inconspicuous, the motor is badly damaged, the connecting rods bend, cracks occur in the cylinder block, etc.P. After a hydraulic jacket, it is usually necessary to carry out overhaul of the engine. In the second case, the problem is not critical, since after removing moisture, the performance of the ignition system and the power unit often can be restored.

Also, the car may gallop hot if there is too little fuel in the fuel tank. Often often the motor stops when driving uphill. The fact is that during a protracted rise, the car for a long time is in this position when the fuel tank is inclined and fuel level is not enough to supply through the fuel intake. It is quite obvious that in this case the engine will stall.

Features of the work of a trimmer for grass

All trimmers for grass are classified according to the type of power: gasoline or electricity (from the network or battery). It should be noted that gasoline mowers in many respects exceed their electric and battery analogues. Despite the fact that they all perform similar functions, the difference in performance, maneuverability and effectiveness is very noticeable. However, the general principle of operation of all types of manual braids is almost no different- the devices are equipped with engines (two- or four-stroke ICE or electric motors), which drive the cutting unit (reel with fishing line or metal disk). All elements are fixed on the line of straight or curved shape, including the handle for controlling the trimmer on which the main buttons are located.

Since the problem of weak revolutions is more characteristic of gasoline trimmers, they will be given more attention. So, the lawn mower is very comfortable in work and unpretentious in maintenance. over, most of its malfunctions are caused by ignorance by the user of elementary things, which are written in the instructions. Therefore, before starting the operation of the unit, it is necessary to carefully study the management of the manufacturer. In particular, in order to start the engine, it is necessary to do the following sequential actions:

  • turn on the ignition button;
  • press the silicone button for pumping gasoline several times;
  • close the air damper;
  • The gas lever is installed in a position for high speeds;
  • first make non.leaf with the starter handle to feel the engine resistance, then jerk sharply.

If the lawn mower started up, but stalled, you need to put the air damper in the middle position and repeat the attempt. When the engine works, you need to slow the gas and open the air damper, since the trimmer for the grass functions only on the leak.

Important! The mode of operation of the trimmer for the grass depends on the various environmental influences. In hot weather, the unit should be given more time to cool. When working in conditions of dense thickets or high vegetation, the engine also overheats strongly. It is necessary to take five-minute breaks every 15-20 minutes.

The lawn mower stalls

When purchasing a lawn mower, you must be prepared for the fact that, as in all other similar tools, breakdowns may also appear in it that will require repairs.

But do not immediately run to the service center and pay big funds to the craftsmen who convince you of the presence of severe malfunctions in the device.

The lawn mower stalls at high speeds

Perhaps more and more a widespread complaint associated with gasoline trimmers sounds like this: “The lawn mower stalls”.

Naturally, a rather harsh fault may be a prerequisite for this. A two.stroke trimmer engine for grass does not develop turns stalling. lawn mower FS 130 give gas stalls. But in most cases, the situation is even easier than it seems to be the 1st gaze.

In order to cope with such an inconsistent, first, try to deal with its causes without the help of others, because, having found out the reason, it’s even easier to fight with the inconsistency, and from time to time it is even self.destructive.

In fact, circumstances, this is when the lawn mower stalls at high speeds, there are quite a lot of these circumstances.

Why is a Chinese lawn mower not developing momentum?

The trimmer for grass does not gain momentum, a very common inconsistent and of course does not always have a common solution.In this.

The lawn mower is not gaining momentum, the cause of the malfunction and eliminate it

1st launch of the latest lawn mower.Removed the grid from the silencer, began to work.

Another, this is the presence of malfunctions in the power system.

In this case, the lawn mower will stall at idle. At speed stalls a trimmer for Champion grass. GAPHOLLOSKALL GOODLUCK 4300 stalls video revolutions. The lawn mower stalls when you press the gas. At high speeds, the lawn mower stalls. The problems with the power system may lead to a drainage or incorrect carburetor adjustment.

Vibrations that take place in the process of operation of the lawn mower can lead to a reservoir.

Incorrect adjustment of the lawn mower can be fixed by simply adjusting it in accordance with the requirements specified in the operating instructions.

In addition, sometimes gasoline trimmers for grass can stall due to the fact that the valve located in the gas tank lid just clogged or sticks.

To find out, try using a braid by loosening the gas tank cover.

trimmer, grass, there, reason

If in this mode the device works properly, clean the valve.

Some tricks of work with a benzotrimer.

Now is summer, and gasoline engines have become a constant attribute on land plots. Great tool, powerful and mobile. You can mow grass with a gasoline trimmer and cut dry weeds. But sometimes the braid for grass does not start, works with interruptions or does not develop full power. Now, of course, is not the time to work! As they say, this is rather the vibration of the starter handle than the kosba.

Problems with the launch do not only have an old braid for grass, but also in the new. what is the answer? Only one thing remains. listen to expert advice and adopt their practical experience.

You bought yourself a new gasoline trimmer for grass and difficulties immediately arose with it. It starts very badly. If you rush a little, and then turn it off, then get it “on a hot” even bigger problem than “for cold”. What to do with it, I won’t know how to start it right?

Pour the fuel using the silicone button (primer) on the bottom of the carburetor. Press as much (or more) as indicated in the instructions, usually about 8-10.

At high speeds, fix the throttle lever using the throttle button.

Pull the starter lever 2-3 times. The engine must “grab”.

If the engine “grasps” and stalls, transfer the throttle to 1/2 and try to run again. If the engine still starts, lower the throttle and transfer the air damper to the position “Open”. Start operation.

When performing manipulations with a fuel pump, do not be afraid of overflow. If this happened, and you, as they say, “flooded the cork”, do not need to unscrew it, just transfer the air damper to the “open” position and, holding the full gas, simultaneously scroll through the engine with a starter 2-4 times. Then you can start the engine and start work.

When pressing gas

If the lawn mower stops when pressing the gas, then the reasons may be the following.

  • The most common option is a fuss of adjusting the carburetor, which occurs with significant loads on the drive, after a prolonged inaction of the mechanism or when it is used in severe conditions.
  • The clogging of the fuel valve, which eliminates it with the message, as a result of which gasoline according to the system begins to flow normally.
  • The weakening and hanging of the cable in the carburetor. Also, a tensile of the fuel hose can occur up to its rupture, caused by the action of a significant load.
  • Clogging of the saapun (check valve), as a result of which fuel does not enter the tank.

If the problem is associated with the carburetor node, then it can be recognized by the appearance of vibrations of the lawn mower. Когда лопается шланг или растягивается трос — выполняют замену данных комплектующих.

Reasons why a new trimmer is not started for grass

Difficulties with the launch do not only have the types of motorcycle, but also in completely new. In this situation, there is only one way out. to listen to the advice of our experts and take advantage of their practical experience!

The reasons why the new gasoline trimmer for grass does not start is eliminated by the instructions for the plant of the Motokos from the forum users, which sounds like this:

  • Turn on the ignition.
  • Switch fuel with a silicone button (primer) located below the carburetor. Presses must be done as much (or a little more) as it is written in the instructions, usually about 8-10.
  • Close the air damper.
  • Fix the gas lever with a button at high speeds.
  • Twer the label handle 2-3 times. The engine must “grasp”.

If the engine “grasped” and stalled, then you need to transfer the air damper to 1/2 and try to start the motor again. If the motor has started, then drop the gas and transfer the air damper to the “open” position. The trimmer for the grass is easily launched. We start work.

Performing manipulations for pumping fuel, no need to be afraid to shift it. If this happened, and “flooded the candle”, then it is not necessary to unscrew it, it is enough to transfer the air damper to the “open” position and, holding the full gas, simultaneously scroll through the engine with a starter 2-4 times. After that, you can start the engine and proceed to the mocking of the grass, not afraid that it will stall.

The continuous operation time of the lawn mower is indicated in the instructions for the operation of a trimmer for grass. On average, kosim for 15-20 minutes, after which you need to drown out a trimmer for the grass and let it cool for 3-5 minutes. Also on the duration of continuous work, the weather and operating conditions have a significant impact. In the heat, when mowing high grass, thickets of weeds, under a large load, the trimmer for the grass overheats faster, does not work and hardly starts after the break.

Main reasons

The following reasons are possible why the lawn mower or trimmer for grass stalls when trying to re.start and continue the interrupted work:

  • malfunctions in the engine;
  • refusal to supply gasoline and oil;
  • damage to pipelines (capillaries, hoses, pipes);
  • malfunctions in the ignition system.

General description of problems with a scythe or trimmer is not enough here. Clear and immediate repair, high.quality maintenance is impossible without specifying the identified cause.

With gazeaming

You click on gas. and the trimmer for the grass stops working, does not develop momentum. The following alleged reasons are possible:

  • The tuning of the carburetor was lost, which appears with an increasing load on the drive itself. after its long downtime or when working in extreme conditions;
  • The fuel valve is clogged with deposits;
  • The carburetor cable is weakened and sag;
  • Excessively stretched, possibly torn off the fuel supply hose;
  • The check valve (sapun) clogged with deposits. fuel does not enter the tank with fuel.

Important! Problems in the carburetor itself give themselves out the vibration of the lawn mower.

With an increase in speed

If the lawn mower (or a trimmer for grass) has stalled when the engine speed is added, check the device according to the following signs:

  • clogging or sticking a valve built into the gas tank cover;
  • valve adjustment violation;
  • A failure in the work of pistons and cylinders. from vibration during the work of a braid for grass or a trimmer for grass, random blows directly in the session of the mowing of grass;
  • violation of the supply of fuel mixture;
  • excess air pumping into the motor;
  • cracking of the fuel intake hose, weakening its compounds.

When the fuel.heating mixture is served with the right portions to the engine in a timely manner. it burns the amount that has managed to enter from the moment of the last gallpling, and he stalls again.

When working idle

Having launched a trimmer for grass or a motorcycle at idle, you find that the device is starting up. but it swallows, after working, say, 5-10 minutes. The reasons here may be as follows:

  • clogging, violation of carburetor adjustment;
  • Initially incorrect configuration of the valve mechanism of the carburetor;
  • air filter clogging;
  • reducing the speed of the gearbox (if any). the incorrect ratio of the fuel mixture;
  • clogging the throttle;
  • penetration of excess air into the fuel system;
  • The fuel ends in the tank (and oil in the tank, if the engine is four.stroke).

If there are problems directly with the carburetor, the machine will stop both after a cold start and after launch on the already worked engine.

Immediately after the start

The stalling of motorcycles or a trimmer for the grass immediately after the start is due to the following reasons:

  • impressive of previously adjusted valves;
  • Initially incorrect setting of the valve mechanism;
  • clogging with fuel supply valve;
  • the hose is worn or poorly attached.

Due to the violated fuel injection algorithm, a lawn mower or a trimmer for grass is greatly vibrated in work.

In the process of warming the engine

If the engine heats up too fast, overheating. a lawn mower or a trimmer for grass works unevenly, as if jerking. After which she stalls. The reason may be as follows:

  • boiling gasoline;
  • The ignition wire was damaged (poor insulation);
  • The coil in the ignition system has noticeably burned out, inter.seal circuits appeared.

The same heating is observed when using rotary (not disk) damper.

When opening an air damper

A lawn mower or a trimmer for grass stalls when raising the damper for the following reasons:

  • swinging excess air due to the cracked fuel suction hose;
  • sealing oil seals;
  • improper functioning of the fuel and air dispenser when mixing them.

Stop motokos in this case is immediately.

Ways to eliminate breakdowns

The following works are possible by carburetor:

  • cleaning and adjustment of the fuel supply valve;
  • similar work with a valve producing spent gases and pairs (after fuel burning);
  • replacement of the spring weaker on the entrance valve;
  • restoration of the tension of the carburetor cable;
  • replacement of the fuel leaks hose, verification and strengthening of a weakened connection;
  • changing the rotor damper disk;.
  • Change of faulty wire or ignition coil.

The list of work on the work may also include the cleaning of the nozzles (in a 4-stroke engine), replacement of the valve washer, gaskets in tanks and so on.

Operating advice

It is worth paying attention to several recommendations for working with a benzoca or a trimmer, extending the service life of the device to several times.

  • As soon as you notice that the lawn mower or trimmer vibrates for the grass. immediately stop working and check the serviceability, performance of specific parts.
  • Valves adjustment and checking the work of pistons and cylinders, cleaning and changing the nozzles perform, starting from the requirements set forth in the user guide and the recommendations of the masters of service centers.
  • When air bubbles enter the system due to impaired fuel hose-give in to gas. With the combustion of gasoline with higher speeds of the gas bubbles motor will be less. But this is a temporary measure. As soon as possible, disassemble the unit and eliminate the cause of the suction of excess air.
  • Do not work as a unit in cold weather, not heating the engine. under load it can often stall. The effect here is the same as in the case when the driver in.40 started the car and immediately drove off, without waiting for the engine heating.
  • Do not leave the unit on the roadway. During the accident, the hit will immediately break, and this will make the purchase of a new unit for a forced measure. A car that has crashed into it at best will receive damage to the body and bumper.
  • Avoid working with a motorcycle or a trimmer in a downpour. Water getting along with air in the worst case can lead to engine explosion. Similar situations arose with cars.
  • Do not use unverified vehicles and lubricants. The mower warms up the engine more than it would do the car itself. when overheating, it will automatically lose its lubricants. It will turn into a burned out reagent. sticky, too viscous and viscous, like fuel oil. He will immediately stall (and drown out) the motor.
  • If the oil is old, previously merged from the tank of the machine or other (or the same) lawn mower (on a 4-stroke engine)-defend it, filter to clean from dirt and metal. But at the first opportunity, purchase fresh motor oil.
  • If the engine is two.stroke. observe the ratio of gasoline and oil. For compositions with mineral oils, this is approximately 34: 1, for semi.synthetics. 42: 1, for purely synthetic. 50: 1. Do not violate these proportions: “rewinded” gasoline will not burn out and quickly clog the engine, “under.appropriate”. will accelerate the wear of its mobile parts.
  • In terms of viscosity to winter classes, they include marking oils: SAE-0W/5W/10W/15W/20W/25W. To the summer-SAE-20/30/40/50/60. For example, SAE 10W-40 is already all-season oil (when working mowers from spring to autumn inclusive). Be sure to check with the manufacturer exactly what oil is needed.
  • Always use high.quality gasoline that has passed the manufacturer all stages of cleaning.
  • Recommended octane number of gasoline-AI-92/95/98. The use of the 76th can lead to a non-power of the engine by frequent stalling if you are poured, for example, the 76th or 80th gasoline.
  • If you are not sure of the independent solution of problems with a gas station (which does not gain move and often stalls)- call the master or contact the service center for repairing motor and garden equipment. Specialists do not get used to doing this work for you.

Read how to use a trimmer for grass video

Observing all these precautions, you will give your mower for many years of fruitful work, and yourself. the luxury of well.groomed lawns, comfort and convenience when mowing unnecessary vegetation in your site.

About the reasons why the lawn mower stall when you press gas, watch in the next video.

What could break

Malfunctions with a benzocosa associated with the fact that this device is not started, in a certain way are classified by specialists of service services. They stand out malfunctions with the following nodes of the mechanism:

2-in-1 trimmer for trimming beard, ear and nose hair from ATB, overview and device

  • the engine in which the piston and bearings can be worn out or fail to crack the crankcase;
  • the fuel supply system, while it is possible to clog the filter or problems with the carburetor;
  • mechanical damage to wires, tubes, hoses;
  • The ignition chain.

The gasoline trimmer for the grass does not gain momentum what problems

This all.produced task has a number of different circumstances. At one time of working with the device, you can meet with obvious problems, the signs of which are correctly tracked, and with asymptomatic options. The 1st option is more simple from the point of searching for difficulties. If the trimmer for grass does not develop, and there are no exact signs of breakdowns, then you will need to alternately check more common cases of problems, and if the prerequisite is detected, remove it.

Non.disclosure, when the lawn mower does not develop, is mainly found in gasoline engines. This is tormented by the technique of different models, for example, Husqvarna, Champion, Stihl.

With high.quality products, such problems are more frequent than with cheap ones from unknown manufacturers.

Part of the structural parts with which difficulties will be associated are available to visual examination, to verify the functioning of other components it will be useful to disassemble the motorcycle.

The trimmer for the grass does not develop momentum if refined with low.quality fuel. Therefore, the engine may not start or work with “jerks”, changing the speed of rotation of the knife or fishing line.

To find the quality of gasoline used without the help of others, subsequent deeds are made.

  • The candles are removed with a special key.
  • Inspect their working contacts for the presence of a rabid brick color plaque: if it is of course, then the fuel used contains significant inclusions of the additives.

Candles in general often act as indicators that allow you to find problems with the combustion chamber of the internal combustion engine, since of course they can be quickly removed and look around.

If plaque is detected, you need to drain fuel in a tank and replace it with a high.quality. The gas mower used should be refuel only with those brands of gasoline, which are indicated by manufacturers in the operating annotation. Also, the candles should be cleaned from plaque before installing to the place.

The subsequent all.fought prerequisite for lowering the number of revolutions on the trimmer is the pollution of its air or fuel filters. At the beginning, the inconsistent is that the fuel-air mixture entering the combustion chamber is not saturated with oxygen, and therefore not all the gasoline burns. This does not allow Motokos to develop the highest power.

Pursuing the purpose of checking whether the air filter really will indulge, it is necessary to remove it (for previously promoting the cover for this purpose) and turn on the lawn mower. If it works fine, then the knocked.down filter element is knocked down you need to stick a new.

If the situation remains unchanged after the actions done, then it is necessary to study the fuel filter. The essence of difficulty is similar to a previous case, only a bidding of oxygen does not work than gasoline for the usual operation of the device. The elimination of this task is also carried out by the usual change in the filter element. Air and fuel filters are cheap. It is not difficult to change them without the help of others, and all the work does not take extra time.

It should be noted that without a fuel filter, it is forbidden to operate a trimmer for grass by annotation, and a piston knot is useful to repair a piston node through a kutser.

With the invariable operation of the lawn mower, the spark plugs are polluted and wear out over the years. To check this, they are removed and inspected for the presence of a carbon. Of course, remove the problem with 2 methods: with the ability, return an old candle, or simply set in its place the latest.

The lawn mower stalls in other words suffocates when pressing the gas

If the inconsistent is associated with the carburetor node, then it can be recognized when the lawn mowing appears when the vibrations appear. When a hose bursts or a cable stretches, a change of data data is made.

User manual

Particular attention should be paid to how to properly carry out the first start and run.in gasoline mowing. Competent actions will allow the maximum operation of the trimmer for the grass and reduce the costs of its maintenance and repair

Before you first start the device, you will need to carry out several preparatory actions. Their list includes a visual assessment of the state of the gearbox and the preparation of a high.quality fuel mixture, taking into account what kind of oil should be poured in accordance with the instructions and recommendations of the manufacturer.

It is on the composition of the fuel that experts and experienced owners of gasoline trimmers recommend fuel. In situations with two.stroke engines, unlike four.stroke, components will be gasoline and oil

Read how to unscrew the clutch on the Stihl chainsaw

The proportions are indicated in the relevant instructions attached to the technique, or on the labels of combustible materials. In annotations, among other things, the type of fuel and motor oil recommended by the developers indicates.

After all the nodes of the trimmer for the grass are examined and the fuel is properly prepared, you can proceed directly to its launch and the subsequent run.in the ICE. This process includes the following steps:

  • The lawn mower must be placed in a horizontal plane on the maximum flat surface;
  • The lever that controls the air damper is transferred to a closed position;
  • Using a primer, fuel is pumped to the carburetor (several movements are enough);
  • the ignition is turned on by the corresponding switch;
  • The launch cord should be pulled out as smoothly as possible until the resistance is felt;
  • the launch of the device is carried out by several sharp jerks of the cord;
  • After the engine has started, you should open the air supply.

In some situations, a trimmer for grass may not start or immediately after starting to stall. In such cases, it is necessary to slightly open the air supply to the carburetor and repeat the attempt. After a positive result, you should let the motor work at least 5 minutes in idle mode.

Using the lever, the air supply should be set in such a way that the reel with a fishing line or the knives remain motionless. After the full heating of the motor, the damper is opened by the transfer of the aforementioned lever into a position marked by the ON badge, and for 20-30 seconds, the gas regulator is half-clamped. At the next stage, the trigger is released, and the trimmer for the grass works at idle for approximately 40 seconds. Such manipulations are repeated for 10-15 minutes, after which it is necessary to take a 20-minute break.

Repetition of the listed actions is further running in the ICE of the gasoline mowing. The next stage is the reducer of the gearbox, for the implementation of which you will need to choose the appropriate area with soft grass. The latter is mowed for 5-10 minutes with periodic pits (1/2-2/3 of the maximum revolutions). This cycle is repeated several times with an interval of 20-25 minutes.

Sooner or later, the owners of the trimmers have to deal with the need to change the fishing line for the trimmer. This is an integral component of the operation of such a technique. There are several ways to update the considered cutting element. The easiest option is the following manipulations:

  • Remove the head from a trimmer for the grass and carefully clean it;
  • reinforce the required fishing length (it is recommended 2-3 meters) and bite it off with nippers;
  • bend the fishing line for the trimmer so that one end is 15 cm longer than the other;
  • Place the jacket on the spike located between the grooves of the coil;
  • wind a fishing line for a trimmer simultaneously in two directions, temporarily fixing it in grooves (the winding direction is indicated by the arrow);
  • pass the ends through special holes in the lid;
  • insert a coil with a new fishing line in place and snap.

Often in the operation of the Stihl lawn mower, a carburetor adjustment may be required. In the presence of appropriate knowledge and skills, it can be carried out independently. At the preparatory stage, you need to thoroughly rinse the air filter. It is worth noting that this is strongly recommended to do every ten hours of operation of the mowing.

Setting is carried out by three screws, one of which is responsible for supplying fuel. It is twisted until the internal combustion engine starts to stall. Then you should unscrew the screw for a quarter of turning (if the engine stalled, then by 1/2). After starting the trimmer for the grass, they continue to turn off the same screw until the ICE begins to work stably at increased speeds.

The trimmer for grass stalls. how to eliminate the problem

A gasoline trimmer for grass is a useful tool for cleaning from unnecessary grass of house territories and large area lawns. The design of this technique is quite complicated, therefore, if the device breaks, there may be several reasons. The most likely factors that have caught a breakdown are usually described in the user guide. Knowing why a trimmer for grass stalls, you can try to independently eliminate the defect. The most common malfunctions provoking the motorcycle stops, and the ability to repair them with your own hands is in the material further.

In order to most accurately determine the cause of the trimmer malfunction for grass of any brand (for example, echo) and find out the possibility of eliminating it, you need to install, when performing what action the device stalls. The engine can turn off both at idle and at high speeds, heated under load or immediately after starting and t.D.

If you stalled after gas supply

Owners of gasoline braids often mention that the lawn mower stalls when you press the gas. Usually such a breakdown occurs due to problems in the carburetor. A failure in his work can occur due to long-term storage, use in difficult conditions, significant overload of the motor. The symptom of such a breakdown will be vibrating movements of the device during operation.

On a note! Users familiar with the repair of a car carburetor can try to restore this important node of the trimmer for the grass on their own, using the instructions for operating. Otherwise, the correct decision will be to seek help from the service center representatives.

Sometimes a trimmer for grass stalls when you give gas because the fuel valve is clogged. This interferes with the supply of gasoline. To eliminate the problem, it is enough to loosen the valve. Thus, normal supply of carburetor fuel will be restored.

Another possible reason why the lawn mower stalls when gas is supplied is pollution of the soundtress (check valve). This detail prevents the appearance of a vacuum in a gas tank. If it is clogged, the air does not flow, which means that fuel does not go to the carburetor. To eliminate the problem, it is necessary to clean this element.

If it stalled at high speeds

If the carburetor stalls at high speeds, this means that in idle and small there are enough incoming fuel, and to work on high is not enough. Then it is necessary to check the serviceability of the following nodes of the trimmer for the grass.

  • Fuel hose. its integrity could be violated as a result of cracking. In this case, you need to replace the part. Or maybe you just need to tighten the clamps.
  • A filter network between a carburetor and a hose for supplying a gasoline mixture-it could clog. In this situation, it is necessary to clean the detail.
  • The valve on the gas tank cover. he could stick or clog with garbage. Cleaning is also necessary.
  • Carburetor. perhaps as a result of constant vibration, it was resolved. This is usually characteristic of cheap Chinese details. To eliminate the problem, it is necessary to set up according to the instructions. In some cases, it is enough to only weaken the tightening of the carburetor case. If the adjustment is not possible, it is necessary to install a new element.
  • Additionally, check the air filter. Perhaps it will need to be washed and cleaned or replaced with a new one, as he could clog with dirt and particles of grass when tilted technology, when the user mowed in hard.to.reach places.

If you stalled during work idle

If the lawn mower stalls, working idle, there may be several factors reasons.

  • First you need to check the prepared fuel solution, when it comes to a four-stroke trimmer working on a gasoline-oil mixture. There is a chance that it is made incorrectly. the proportions are not withstanded. Because of this, the gearbox is warming up, and the revolutions on the drum are lowering.
  • Another probable cause is blockage of elements such as a throttle, air filter or carburetor. You need to clean the indicated details.
  • Another possible factor is to resolve or incorrectly carried out carburetor adjustment. You need to adjust the setting according to the instructions.
  • Observe this problem mono and when opening the air damper. In this situation, the lack of fuel for a trimmer for grass occurs through the fault of the air flow.

If the device does not have enough fuel, it works properly at high speeds or when they increase, but stalls at idle. If the root of the problem consists in the carburetor, the lawn mower will be disconnected both with cold startup and hot.

If you stalled after starting

If the technique starts and stalls immediately after starting, this indicates the wrong settings or deducting the device. As a result of this, the fuel enters the engine unevenly, which leads to significant vibration and disconnecting the trimmer for the grass. To fix the breakdown, it is necessary to reconfigure the device according to the user management.

Another probable problem is the blockage of the valve supplying the gasoline mixture. It must be cleaned.

On a note! If the trimmer for the grass starts, but immediately stalls, it may also mean that the fuel is moving to the carburetor with difficulty. Weakening the valve will help to eliminate the problem. this will provide uniform and free circulation of fuel in the device.

Another possible reason is the damaged fuel intake hose. Air can penetrate through cracks and holes into the system. To solve the problem, you need to increase the engine speed in order to get rid of air bubbles that have penetrated the device.

If you stalled when opening the damper

If the technique works properly at idle, but stalls when opening an air damper, this reports about the penetration of air into the system through cracks in the fuel supply hose or damaged oil seals. To fix the breakdown and establish the work of the tool without driving air from the atmosphere, it is necessary to replace damaged parts.

Preventive measures and operating rules

So that the lawn mower does not work and does not stall when starting, it must be correctly stored and operated. Compliance with the following simple recommendations will forget about problems.

  • When begging the grass, you need to monitor the state of the cooling system. It is also necessary to regularly clean the channels in the case and starter’s ribs.
  • To clean the tool, you should use kerosene, solvent, or other washing tools.
  • You can not clean a hot tool. it must cool before washing.
  • It is important to observe the recommended working mode. this will avoid overheating of the engine.
  • If a braid for grass is not used over the next thirty days, the fuel must be drained, otherwise it will fall into heavy components that can score the channels of the carburetor.
  • After the fuel is merged, the trimmer for the grass should work at idle for some time until it turns off. This will allow you to completely get rid of the rest inside the working mixture.

To store the tool in cold weather, you need:

  • completely drain the fuel;
  • disassemble the lawn mower, wash and clean all available components;
  • inspect the condition of the parts, eliminate all defects that can be corrected;
  • pour the required amount of oil into the gearbox;
  • Clean the air filter;
  • perform partial disassembly of the engine, wash all moving parts, blow and lubricate thoroughly;
  • To lubricate the piston, unscrew the candle, then raise the piston to the upper dead point by the starter, pour a small amount of oil into the hole for the candle and do the crankshaft several times.

Important! If there is no way to store a trimmer for grass in a warm dry room, you must first wrap the motor with an embarrassed rag.

Only by observing these rules, you can be sure that the lawn mower will work properly and will not stall for a number of seasons.

As you can see, stopping the work of a trimmer for grass can be caused by many reasons. Most of them can be fixed independently using the user instructions. In cases where there is no self.confidence, the equipment is recommended to be attributed to repairs. It is worth remembering that incorrect actions can cause even greater harm to the trimmer. As a result, the repair of Motokos will cost a much larger amount than it would be initially, and in the worst case, it may be necessary to buy a new unit.

The trimmer for grass stalls. how to eliminate the problem

A gasoline trimmer for grass is a useful tool for cleaning from unnecessary grass of house territories and large area lawns. The design of this technique is quite complicated, therefore, if the device breaks, there may be several reasons. The most likely factors that have caught a breakdown are usually described in the user guide. Knowing why a trimmer for grass stalls, you can try to independently eliminate the defect. The most common malfunctions provoking the motorcycle stops, and the ability to repair them with your own hands is in the material further.

In order to most accurately determine the cause of the trimmer malfunction for grass of any brand (for example, echo) and find out the possibility of eliminating it, you need to install, when performing what action the device stalls. The engine can turn off both at idle and at high speeds, heated under load or immediately after starting and t.D.

If you stalled after gas supply

Owners of gasoline braids often mention that the lawn mower stalls when you press the gas. Usually such a breakdown occurs due to problems in the carburetor. A failure in his work can occur due to long-term storage, use in difficult conditions, significant overload of the motor. The symptom of such a breakdown will be vibrating movements of the device during operation.

On a note! Users familiar with the repair of a car carburetor can try to restore this important node of the trimmer for the grass on their own, using the instructions for operating. Otherwise, the correct decision will be to seek help from the service center representatives.

Sometimes a trimmer for grass stalls when you give gas because the fuel valve is clogged. This interferes with the supply of gasoline. To eliminate the problem, it is enough to loosen the valve. Thus, normal supply of carburetor fuel will be restored.

Another possible reason why the lawn mower stalls when gas is supplied is pollution of the soundtress (check valve). This detail prevents the appearance of a vacuum in a gas tank. If it is clogged, the air does not flow, which means that fuel does not go to the carburetor. To eliminate the problem, it is necessary to clean this element.

If it stalled at high speeds

If the carburetor stalls at high speeds, this means that in idle and small there are enough incoming fuel, and to work on high is not enough. Then it is necessary to check the serviceability of the following nodes of the trimmer for the grass.

  • Fuel hose. its integrity could be violated as a result of cracking. In this case, you need to replace the part. Or maybe you just need to tighten the clamps.
  • A filter network between a carburetor and a hose for supplying a gasoline mixture-it could clog. In this situation, it is necessary to clean the detail.
  • The valve on the gas tank cover. he could stick or clog with garbage. Cleaning is also necessary.
  • Carburetor. perhaps as a result of constant vibration, it was resolved. This is usually characteristic of cheap Chinese details. To eliminate the problem, it is necessary to set up according to the instructions. In some cases, it is enough to only weaken the tightening of the carburetor case. If the adjustment is not possible, it is necessary to install a new element.
  • Additionally, check the air filter. Perhaps it will need to be washed and cleaned or replaced with a new one, as he could clog with dirt and particles of grass when tilted technology, when the user mowed in hard.to.reach places.

If you stalled during work idle

If the lawn mower stalls, working idle, there may be several factors reasons.

  • First you need to check the prepared fuel solution, when it comes to a four-stroke trimmer working on a gasoline-oil mixture. There is a chance that it is made incorrectly. the proportions are not withstanded. Because of this, the gearbox is warming up, and the revolutions on the drum are lowering.
  • Another probable cause is blockage of elements such as a throttle, air filter or carburetor. You need to clean the indicated details.
  • Another possible factor is to resolve or incorrectly carried out carburetor adjustment. You need to adjust the setting according to the instructions.
  • Observe this problem mono and when opening the air damper. In this situation, the lack of fuel for a trimmer for grass occurs through the fault of the air flow.

What to Check if Your Grass Trimmer Isn’t Cutting

If the device does not have enough fuel, it works properly at high speeds or when they increase, but stalls at idle. If the root of the problem consists in the carburetor, the lawn mower will be disconnected both with cold startup and hot.

If you stalled after starting

If the technique starts and stalls immediately after starting, this indicates the wrong settings or deducting the device. As a result of this, the fuel enters the engine unevenly, which leads to significant vibration and disconnecting the trimmer for the grass. To fix the breakdown, it is necessary to reconfigure the device according to the user management.

Another probable problem is the blockage of the valve supplying the gasoline mixture. It must be cleaned.

On a note! If the trimmer for the grass starts, but immediately stalls, it may also mean that the fuel is moving to the carburetor with difficulty. Weakening the valve will help to eliminate the problem. this will provide uniform and free circulation of fuel in the device.

Another possible reason is the damaged fuel intake hose. Air can penetrate through cracks and holes into the system. To solve the problem, you need to increase the engine speed in order to get rid of air bubbles that have penetrated the device.

If you stalled when opening the damper

If the technique works properly at idle, but stalls when opening an air damper, this reports about the penetration of air into the system through cracks in the fuel supply hose or damaged oil seals. To fix the breakdown and establish the work of the tool without driving air from the atmosphere, it is necessary to replace damaged parts.

Preventive measures and operating rules

So that the lawn mower does not work and does not stall when starting, it must be correctly stored and operated. Compliance with the following simple recommendations will forget about problems.

  • When begging the grass, you need to monitor the state of the cooling system. It is also necessary to regularly clean the channels in the case and starter’s ribs.
  • To clean the tool, you should use kerosene, solvent, or other washing tools.
  • You can not clean a hot tool. it must cool before washing.
  • It is important to observe the recommended working mode. this will avoid overheating of the engine.
  • If a braid for grass is not used over the next thirty days, the fuel must be drained, otherwise it will fall into heavy components that can score the channels of the carburetor.
  • After the fuel is merged, the trimmer for the grass should work at idle for some time until it turns off. This will allow you to completely get rid of the rest inside the working mixture.

To store the tool in cold weather, you need:

  • completely drain the fuel;
  • disassemble the lawn mower, wash and clean all available components;
  • inspect the condition of the parts, eliminate all defects that can be corrected;
  • pour the required amount of oil into the gearbox;
  • Clean the air filter;
  • perform partial disassembly of the engine, wash all moving parts, blow and lubricate thoroughly;
  • To lubricate the piston, unscrew the candle, then raise the piston to the upper dead point by the starter, pour a small amount of oil into the hole for the candle and do the crankshaft several times.

Important! If there is no way to store a trimmer for grass in a warm dry room, you must first wrap the motor with an embarrassed rag.

Only by observing these rules, you can be sure that the lawn mower will work properly and will not stall for a number of seasons.

As you can see, stopping the work of a trimmer for grass can be caused by many reasons. Most of them can be fixed independently using the user instructions. In cases where there is no self.confidence, the equipment is recommended to be attributed to repairs. It is worth remembering that incorrect actions can cause even greater harm to the trimmer. As a result, the repair of Motokos will cost a much larger amount than it would be initially, and in the worst case, it may be necessary to buy a new unit.