Trimmer what to put instead of fishing line
Changing the line in the trimmer: 2 easy ways
A trimmer is a necessary and useful tool for a summer cottage and a private house. Many people own and actively use it, but not everyone knows how to replace the line in the trimmer, especially at first.
In this manual, we will walk you through the entire replacement process step by step. Looking ahead, there are two ways to line the trimmer spool. There is no fundamental difference. the difference is that in the first case one line will be refueled, folded in half, and in the second there will be two such lines.
Preparing for replacement
We disassemble the trimmer spool
For clarity, the mowing head (spool) was removed from the brushcutter. To replace the fishing line, you do not need to remove it, everything is done locally. It doesn’t take long.
We disassemble the trimmer spool. it rests on the latches. Remove the cover by pressing on the latches. If you do not have enough effort to do this with your hands, then use a screwdriver.
The spool consists of the following:
- Spring case
- Cover with locking latches
- Button coil
The principle of operation is as follows. By pressing the button, the spool presses on the spring and comes out of the locking grooves in the spool cap. Holding in this state, the reel can be twisted, thereby adjusting the length of the line. When the button is released, the body spring returns the coil to its original fixed state.
Disassembled trimmer spool
On the bottom of the reel there are several holes for different diameters of the lines. They may differ from trimmer manufacturer. In some cases (like here) they are signed, in others they are not.
These holes are needed to fix the line when changing it. After winding the fishing line on the bobbin, the ends of the latter are inserted into them. This is necessary so that the scaffold does not unwind when the coil is installed in the trimmer body. In other words, it makes it easier to change the line.
Holes for fixing the line
There are models without specifying the diameter of the consumable. Then, in order to find out what the maximum diameter of the scaffold can be used, it is tried on along the holes for the outlet of the fishing line from the trimmer spool body (see the figure below).
Fitting on the holes of the line output
The reel has two line sections separated by a baffle. They may not exist. They are needed only to delimit and facilitate the winding of the consumable.
Two sections for line
First, they are determined with the required length of the loess. The latter is wound into one of the sections of the coil so that it does not go beyond its limits. In this case, 3 mm was wound, the length turned out to be about 2 meters. Those. for two sections you need a 4-meter segment. this is for the 1st method. For the second method, you need two segments of 2 meters each.
Determining the required line length
Now you need to figure out which way you need to wind it. To do this, many trimmer manufacturers apply special designations to the spools, such as in the figure below.
Special designation on the reel
If no such designations were found, then you need to pay attention to the spool body. There is necessarily an arrow that indicates the movement of the mowing head. The line is wound in the opposite direction.
Bobbin case designation
The first way
Line bent in half
The prepared segment (in this case, it is 4 meters) is bent approximately in half. one segment should be 15-20 cm longer, and inserted into a special slot located on the dividing partition.
The line is inserted into the slot
The line is wound in the direction determined earlier. This is done in an interference fit, the line is neatly distributed. In this case, you need to wind a segment that is longer in the section that is closer to the button.
There are designs that do not provide for dividing the coil into two sections. This does not change anything, the line is wound in a similar way. You just need to make sure that the segments do not overlap with each other.
The first should end that section, which is located at the bottom of the coil, i.e. the one closest to the fixing holes.
This tip fits into the corresponding hole in diameter. The line is securely fixed.
The line is securely fixed
A long segment is wound half a turn. There he is similarly fixed. In this case, the segment crosses another section of the coil.
A long segment is wound another half turn
The fixed ends of the coiled line are inserted into the holes of the trimmer spool body.
The fixed ends of the coiled line are inserted into the holes of the trimmer spool body
The coil is attached to the body. The ends of the fishing line are pulled with effort so that the fishing lines previously fixed in the holes of the reel jump out from there. It is easily identified by the characteristic sound (click).
The ends of the line pull up with effort
Button spool snaps into trimmer spool housing.
Button spool snaps into trimmer spool housing
The line was changed successfully. In this case, you need to put it back on the trimmer and you can start mowing the grass.
It should be repeated, there is no need to remove the spool from the trimmer. this was done for clarity of the process of replacing the fishing line. You can disassemble the spool in place, wind it on the spool and put it back.
Line replacement completed successfully
Tips so that they do not hit the trimmer cover can and should be trimmed.
Method 2. two segments
Two coiled line lengths
fundamentally no different from the method The only difference is two wound pieces of fishing line, instead of one.
The end of each segment is folded
The end of each segment is folded.
Two special fixing sockets
There are two special fixing sockets on the coil (see picture above).
We begin to reel the fishing line
They cling to it with a hook formed earlier on the fishing line, and begin to wind the fishing line.
Winding is carried out in a special order
The winding must be carried out in the following order: first the lower line, i.e. the one that is closer to the fixing holes at the bottom of the coil, and only then the top one, i.e. the one that will overlap the bottom section.
The bottom line is reeling
The tips are cut into the holes in the trimmer spool body. They are pulled up until they click, which means that the line has come out of the latches.
The tips are threaded into the holes in the trimmer spool body
The coil is fastened into the body. The line in the spool has been replaced.
The line in the spool has been replaced
How to wind the line around the trimmer cutter head or brushcutters
Changing the line in the trimmer: 2 easy ways
Feedback from our readers is very important for us. Leave your rating in the comments with the reasoning for your choice. Your opinion will be useful to other users.
The continuous operation of the brushcutter is indicated in the trimmer instructions. On average, we mow for 15-20 minutes, after which we turn off the trimmer and let it cool for 3-5 minutes. Weather conditions also affect the duration of continuous operation. In hot weather, when mowing tall grass, thickets of weeds, under heavy load, the trimmer overheats faster.
Many brushcutter problems arise from improperly prepared fuel mixture. In two-stroke engines, lubrication is carried out with a special oil (not ordinary engine oil!), Mixed with gasoline. If the oil is not mixed with gasoline, the brushcutter will quickly fail. Mix the oil / gasoline in the proportion indicated in the trimmer instructions. Usually it is 1:40 or 1:50.
The question often arises: the proportion of 1:50 is how much oil and gasoline?
You bought yourself a new petrol trimmer and immediately got into trouble with it. It starts very badly. If you mow a little, and then turn it off, then turning it on “hot” is an even bigger problem than “cold”. What to do with it, I don’t know how to get it right?
The instruction for the brushcutter plant sounds like this:
Switch on ignition.
Pump up fuel with a silicone button (primer) located on the bottom of the carburetor. Pressing must be done as much (or a little more) as written in the instructions, usually about 8-10.
Close air damper.
Lock the throttle lever with a stop button at high rpm.
Pull the starter handle 2-3 times. The engine should “grab”.
If the engine “grabs” and stalled, then you need to move the choke to the 1/2 position and try to start again. If the engine starts, then we release the gas and move the air damper to the “open” position. Getting started.
When performing fuel pumping manipulations, one should not be afraid to pour it over. If this happened, and, as they say, “filled the candle”, then you do not need to unscrew it, it is enough to move the air damper to the “open” position and, while holding full throttle, simultaneously turn the engine with the starter 2-4 times. After that, you can start the engine and get to work.
Неубиваемая насадка для триммера/ Not killed Trimmer line.
The numbers mean the following: one part of the oil takes fifty parts of gasoline. Hence: 1000 ml (1 liter of gasoline) is divided by 50, we get 20 ml, that is, 1:50.
Thus, you can calculate the composition of the fuel mixture (gasoline / oil) in any proportions. To add oil to gasoline not “by eye”, you can advise to take a 20 ml medical syringe, draw oil into it and “inject” into a container for preparing a fuel mixture.
Also, the ignition coil may be punctured in electrical equipment. In this case, the brushcutter will not start or it will start and work intermittently, and then it stalls, or it will not start at all on the “hot” one.
You can check the coil’s serviceability in the same way as when checking the spark: we unscrew the candle, lean it against the trimmer body. If there is no spark when you jerk the starter, or it appears every other time, you need to change the coil.
During the engine running-in period (this is approximately the work of the trimmer on 2-3 tanks), the amount of oil can be increased. For example, mix it with gasoline in a 30: 1 ratio.
A small amount of oil mixed with gasoline leads to increased wear of the cylinder-piston group. An excess of oil in the mixture, although not so fatal, is also harmful. Coking of the piston rings, rapid formation of carbon deposits in the combustion chamber, and a drop in engine power may occur. In addition, the muffler mesh screen is coked. Therefore, some users (after the end of the warranty period for the trimmer) recommend dismantling it.
The gasoline used in the brushcutter is AI 92. The brand of gasoline is precisely specified in the operating instructions. You should not try to “force” the engine by pouring 95th gasoline into it. This can cause overheating, erratic trimmer operation and breakage.
It is not recommended to leave fuel in the trimmer tank during extended shutdowns. It is better to end the working day with the entire mixture completely exhausted. If this is not done, then, since the gasoline will evaporate from the engine overnight, and a thin film of oil will remain, the carburetor jets may become clogged. This will cause difficulty the next time you start the engine.
It is also necessary to observe safety precautions when storing fuel. Many people pour gasoline into a plastic water bottle. Is it worth doing this?
Some tricks for working with the petrol trimmer.
Articles for the gardener
Types of trimmer lines
The twisted thread with notches makes the least noise during operation. This property can be considered a big plus. Due to its structure, such a thread also increases the power of the instrument itself. A two-piece trimmer line is also available. It consists of an outer and an inner layer. The outer layer is always nylon. This material wears out slowly, is not afraid of loads and temperature changes. Inside there is a metal filling. Due to its rigidity, such material can cut shrubs well.
The line with lugs and spikes on the surface has good wear resistance. It is recommended for use with high power trimmers. It can be used to cut thick grass, dry stems, small trees and bushes. For a home, you need to constantly have 1-2 types of consumables to replace the consumed one. It can be a round thread and a fishing line with a metal filler.
Неубиваемая насадка для триммера 2/ Not killed Trimmer line.
Production material for fishing line
As a rule, nylon line is used for the trimmer. made of polyamide or polypropylene. The cheaper version contains the addition of polyethylene. It is not recommended to use it, since the cord, which contains such a material, is characterized by a reduced resistance to wear and temperature.
To extend the life of a polypropylene line, it is soaked in water for half an hour before direct use. Many people have a question: which is the strongest trimmer line? These can be called strings with a large diameter (about 4 mm), into which aluminum particles are specially added.
Some people practice using metal wire or cables for brushcutters, which is absolutely impossible to do. It is best to use metal trimmer line, which is the most reliable.
In addition, the reinforced trimmer line, which consists of an outer layer and a dense core, is considered extra strong. This ensures its high wear resistance.
Thus, having the necessary information about the characteristics of the trimmer line, you can choose the best option for yourself.
The main parameters of the material are thickness, composition and sectional shape. Let’s dwell on each of them.
Which trimmer line is better?
It doesn’t matter if you use a regular tool with a line, over time you will have to replace working elements. There are a variety of trimmer lines on sale. which one to choose?
The selection of the correct cord thickness is essential. It must match the characteristics of a particular device. If the line is with a large diameter, which is designed for a particular trimmer model, this can lead to tangling of the thread on the spool, overheating of the engine and rapid wear of the bushings.
Select consumables
How to choose the right lawn mower line? The fishing line is a working tool for a country lawn mower. With its help, they mow the grass near fences, paths and trees. It must necessarily have flexibility, rigidity and strength. You can read about the required thread thickness in the characteristics of the mower (trimmer). Typically, a thread with a diameter of 1.2 to 4 mm is used. But each device requires a different diameter. Thinner thread (in comparison with the parameters required by the trimmer manufacturer) significantly increases engine wear and gradually destroys it. Thicker. leads to engine overheating and damage.
To choose a fishing line not only in thickness, but also in shape, it is necessary for this reason: the cord does not cut the stem, but interrupts it. The rotating string hits the surface of the stem many times and eventually separates the top of the stem. For this job, the shape of the incisal edge is an important technical characteristic.
Round. the most common, as it is universal: you can choose it for mowing both fresh and dry grass. It is considered less noisy, especially spiral. But this parameter is not important in all cases. The line for a gasoline trimmer can be as noisy as you like, it is still inaudible while the engine is running.
Polygonal. from 3 to 6 faces. Sharp incisal edges handle coarse, thick stems better. So, a square cord with a cross section of 2.4 mm is able to remove raspberry stems. It should be noted that with a higher efficiency, the polygonal cord is consumed faster, and it should be used only for its intended purpose.
Curly. an asterisk, ribbed, in the form of a twisted square with grooves, and so on. Their “specialization” is different, which it is advisable to learn about in the instructions before choosing. So, an asterisk is recommended for mowing fresh grass, since it is less traumatic: the grass after cutting does not dry out, as when using a round string.
If the battery or electrical unit has engine power:
For electric braids, a round line is most often used. It costs little and is quite popular, as it mows fresh grass very well. Its disadvantage is the high level of noise emitted during operation. Mower manufacturers recommend using a spiral cutter. Also widespread are:
- square section;
- asterisk section;
- rectangular shape.
Lines that have sharp edges and various notches have greater performance. They cut the grass more evenly on the lawn. Large weeds lend themselves well to notched cutting tools. The noise level is not very high and the engine is given extra power when the line is set to a high power trimmer. The working head on the brushcutter, on which the fishing line is wound, is installed a special.
For mowing dead wood and shrubs, twisted two-component lawn mower line is used. It has high strength and tear resistance. Only suitable for mowers with petrol engines. But such a cutting tool is quite expensive. For daily work, its use is very expensive.
The trimmer cutting tool is wound on a special spool. The fishing line is sold in pieces of 10-15 m. It is not recommended to use thin steel wires and stranded cables instead of fishing line. These attachments will quickly damage your lawnmower, including gasoline or electric motors. For a mower with a gasoline engine, a cutting line diameter of 3 mm is usually used. You can reduce it, but it is recommended to use a diameter of no more than 2.5 mm.
A thin thread from 1.2 to 1.6 mm is used to trim the lawn. A thread with a thickness of 2 to 2.4 mm cuts well young grass, and with a thickness of 3 mm and 3.2 mm, it is able to mow thicker and older grass, dead wood and weeds. 4 mm cord is rarely used.
To extend the life of the cord, you should try to avoid contact of the fishing line with stones, trees, foundations, paving slabs. How to wind the line on the trimmer spool correctly?
Incorrect winding will damage the unit. The winding rules are described in the instructions for the device. The parameters of the required cord are also indicated there.
What is the best trimmer line? 06.11.2017 14:09
Conclusion
Do not use a steel cable instead of nylon thread.
It will surely break, and pieces of it will pierce the leather shoes at great speed. Only line up to 15 m long and 2.4 mm to 4 mm in diameter should be wound onto the spool. The ends are brought out.
As they wear out, they expose themselves. To do this, you just need to hit the ground lightly. In other cases, you just need to reduce the speed of the mower and then re-add them. The line is fed automatically. There are reels with manual feed. To feed the working tool, turn off the engine and pull out the ends of the thread by hand.
Testing
The Advanced Trimmer works equally well on undergrowth and tough weeds, as well as on delicate grass.
We install the chain from the chainsaw to the trimmer: how to strengthen the usual trimmer in 15 minutes ??
Everyone who has a summer cottage probably knows that it is sometimes not so easy to put things in order on the site. Most summer residents use a trimmer for these purposes. But here’s the problem: the line mows the grass well, but does not cope with coarse weeds and shoots around the trees.
If, instead of fishing line, you use knives, then it is problematic to mow thin grass with them, although overgrown with them are within their power. And here the know-how will come to the rescue: replace the trimmer line with a chain from a chainsaw. Such a versatile tool will cope with any vegetation that you want to mow on your site.
So that there is no need to constantly change the trimmer line to the disc while putting things in order in the country or in the garden, you can improve the petrol cutter with your own hands.
We prepare components
We take out the components of the mower: metal cap, nut, washer and combination wrench.
We put on the chain
We put a chain from the chainsaw into the drilled holes and lay it so that it does not interfere with the rotation of the cap. The protruding edges of the chain should be the same for better balance.
We fix the cap
Making the markup
We take a metal cap and, using a ruler with a marker, mark diametrically opposite points on it.
Materials and tools for work
In order to improve your trimmer, you will need:
- chainsaw chain;
- metal cap, nut and washer used to secure the knives in the trimmer (included with the mower);
- combination wrench, which is also included in the trimmer kit;
- electric drill;
- a set of drills for metal;
- core and hammer;
- vice;
- welding machine and protective mask;
- ruler and marker.
We attach the cap with a chain
- We remove the nozzle with a fishing line from the brushcutter and attach the washer, cap with chain and nut.
- The trimmer is ready to use.
What you can use in place of the standard trimmer line: 3-way test
A garden trimmer is an indispensable tool in the arsenal of any summer resident. This device facilitates the process of maintaining the territory. With the help of a petrol cutter, you can quickly mow all the grass near the house, while practically without any physical effort.
Many users are interested in how they can replace the standard trimmer line. On the Internet, you can see many different ways, but not all of them are good in practice. Below are the most common options for replacing traditional line.
Fishing line installation: pros and cons
Sometimes a regular fishing line is installed in the drum of a garden trimmer, instead of a special one. it’s just a waste of time. The fishing line is too soft and wears out many times faster than the traditional version. She can really cut grass, but such a non-standard application is not suitable for her. Fishing line can be used exclusively as a backup if nothing else is at hand.
It is also worth considering that it must be thick enough. It is better to insert a line with a thickness of at least two millimeters into the brushcutter. By the way, it may be difficult to install it if the trimmer model provides for winding on a coil.
Installing a metal cable: pros and cons
The most common idea, on the topic “How to replace the trimmer line?”, Is the use of a steel cable. In fact, in terms of efficiency, the metal cable is much better than the standard cable. It is almost unaffected by wear, and mowing the grass is certainly no worse. And yet you need to understand that manufacturers do not just use polymer fishing line, and not an iron cable.
Unfortunately, the downside to wear resistance is the increased wear of the brushcutter’s transmission. Due to the fact that the line breaks, it does not overload the mechanical part of the device, but simply wears out with use.
If desired, you can use a steel cable, but it is important that during operation it does not touch the protective casing in any way. The ends of the cable must be welded so that they do not unravel.
Installing plastic ties: pros and cons
If during work the line suddenly ends, and there is still a lot of work, then it is not necessary to look for a new one. Its function will temporarily be performed by plastic clamps. They are quite tough and can handle just about any grass.
The disadvantage is rapid wear and tear. The effectiveness of plastic clamps, in such a non-standard application, is also low. However, this alternative can always be used.
Conclusions on effectiveness
Summing up, it should be said that manufacturers use special fishing line for a reason. It is optimally suited for working with this tool: it mows the grass well and does not overload the device mechanics. If it is over, and there is still a lot of work, it is better to buy a new one. For temporary use, of course, you can install a metal cable, but at the first opportunity it must be changed to a special fishing line. Otherwise, it will have a detrimental effect on the technical condition of the tool.
What to put instead of fishing line on a brushcutter
Very often, trimmers and brushcutters want to increase the productivity of these garden tools. This is due to the fact that when purchasing a petrol cutter, few people think about the power, the radius of the grass bevel, and other equally important characteristics.
Having purchased a tool, many face difficulties when mowing small bushes and tall grass. Therefore, the question of what can be put on the trimmer instead of fishing line is more relevant than ever.
In principle, a slightly larger diameter line can be installed on the trimmer and brushcutter than the one recommended by the manufacturer. You can also try to use a steel cable for these purposes, but here you need to be extremely careful, and additionally fix it.
Even the slightest bounce of a stone towards the operator or others from the cable (or a piece of the cable itself) can lead to unpleasant consequences, such as injury. What else can be used instead of fishing line on the benzotrimmer?
What can be put instead of fishing line on a brushcutter and a petrol trimmer
If it turns out that there is no special trimmer line at hand, then you can use the most common fishing line. Usually they take a fishing line with a diameter of 2 mm, but you can try to put a fishing line and thicker.
The only thing you will have to face in this case is the difficulty of winding the line. The fishing line is too soft, so everything here largely depends on the design of the reel. If the line has to be wound, then this should be done in a small piece.
It is much easier to install a fishing line on a trimmer, in the case when its reel is not wound (just thread the desired piece of fishing line or cable through the hole, and then snap the reel).
Can I use a cable instead of a line on the trimmer
Of course you can. However, at the same time, it is worthwhile to understand all the insecurity of this venture, and the ultra-fast failure of the petrol trimmer transmission out of order. Indeed, a steel cable is a hundred times stronger than a fishing line, even a special trimmer. It will not tear as often from grass, branches and stones, so it will last much longer.
At the same time, you need to understand that the line breaks when the trimmer is working not just like that, but from a strong load. As a result, the brushcutter engine does not stall, while dynamic shocks to the brushcutter’s transmission are absorbed. In the case of a steel cable, the entire load will fall on the transmission, as a result of which it will quickly fail.
If you really want to try using a cable on a petrol cutter, then at least you need to install it correctly. First, you must not wind a long rope around the reel. Make it so long that it does not interfere with the trimmer guard when the spool rotates.
Be sure to clamp the cable with washers in the middle and place one drop of welding at its ends so that it does not bloom. As a result, the cable should not have any protrusion, and welding at the ends will protect it from unraveling. However, even in this way, it is very unsafe to use the cable on the brushcutter or trimmer. It is much easier to use ready-made factory nozzles.
Factory attachments for trimmer and brushcutter
Today on sale you can find ready-made brushcutter and trimmer attachments, which make it possible to increase the efficiency of this tool several times. Attachments can be made in the form of knives, with a chain or steel cable.