What kind of oil is in the vibrator of the vibrating plate

Fourth: how is the engine running in.

Air-cooled engines “don’t like” idling. Start the engine, warm it up for 1-2 minutes. and run in at work. During the break-in, try to adhere to 50-75% of the load and take obligatory breaks in work after 20-25 minutes. After a break, when the engine has cooled down (15-20 minutes), you can continue working again. In this mode, the engine should run for the first 4-5 hours, after which it is imperative to change the oil. Running in finished.

What you need to know about the running-in and operation of four-stroke air-cooled gasoline engines installed on garden, construction and road moto equipment.

Air-cooled four-stroke gasoline engines are widely used in gardening equipment. tillers, motor-cultivators, lawn mowers, snow blowers, motor pumps, mini-tractors, on construction and road-building equipment. gas generators, vibrating plates, vibrating rammers.

READ THE OPERATING INSTRUCTIONS before operating the engine. Unfortunately, many buyers don’t. Therefore, the most elementary questions about the use of the motor arise.

TIP: READ ENGINE OPERATING MANUAL.

The second reason for the breakdown: during transportation or storage, the engine was turned over.

Since the engine is 4-stroke. gasoline is poured into the tank, oil into the crankcase. and they should not mix. After an overturn, these components are usually mixed in a carburetor. After that, the engine will need to be disassembled and cleaned.

DO NOT OVERVIDE A FUELED ENGINE.

Second: what kind of oil to fill in the engine crankcase.

Many people consider famous brands of automobile oil to be the best for use in engines for a tiller (cultivator, snowmobile, electric generator, motor pump, etc.). This is absolutely not the case. Automotive oils are designed to work in water-cooled engines, not air-cooled ones. The boiling point of automotive oils is lower than that of oils that contain special additives for air-cooled engines.

Use oil with quality class SF, SG, SH, SJ, CD or higher. Do not use oil additives. Select oil viscosity based on ambient temperature.

SAE 30 (5 ° C and above) is recommended for temperatures above 5 ° C. May cause difficult starting when used below 5 ° C.

10W-30 (-18 to 38 ° C) is recommended for variable temperatures. This oil provides a cold start to the engine, but can lead to increased oil consumption at temperatures above 27 ° C.

Check oil level more frequently at elevated air temperatures.

Synthetic 5W-30 (-30 to 40 ° C). Synthetic oil, provides engine operation over the entire temperature range, as well as easy starting and reduced oil consumption.

5W-30 (5 ° C and below) is recommended for work in winter conditions.

FILL ONLY OILS SPECIFIED IN ENGINE INSTRUCTIONS.

Always check the oil level. The level should be up to the last thread of the filler neck in the horizontal position of the engine (as shown in the figure). The fill and drain holes are located at the front and rear of the engine.

Engine oil fill level

On lawn mowers, pay attention to the dipstick. Vertical shaft motor dipstick has marks.

Different engines have different crankcase volumes. If you have a 4, 5.5, 6.5 or 7 hp engine then you need to fill in 600 ml. oils. Engines 7.5 hp 900 ml is poured. In motors with a capacity of 8, 9, 11, 13 and 15 hp. respectively 1.1 l.

The main causes of engine breakdowns

REMEMBER. Engine breakdowns are mainly caused by improper operation.

Instruction for running in and operating a 4-stroke engine

Third: starting the engine.

When the engine is started for the first time or cold, there is an increased load on the piston system. High revs can damage the motor. Therefore, it is necessary to start the motor at 1/3 throttle position. And you need to run in at medium speeds.

First: what kind of gasoline should be used.

We recommend using clean, fresh, unleaded RON 92 RON gasoline. Air-cooled engines are not designed to operate with AI95 and AI98 fuel. The 95th and 98th gasoline contain additives that have a detrimental effect on the piston system of the engine, leading to overheating and breakdown.

Do not mix oil with gasoline. Doing so may result in engine malfunction which is not covered by the warranty.

USE FRESH AI-92 GASOLINE WITH A SHELF LIFE OF 30 DAYS.

Repair of the vibrator of the SPLITSTONE VS-245 E8 vibrating plate

Repair of the vibrator of the SPLITSTONE VS-245 E8 vibrating plate.

What kind of oil should be poured into the vibrating plate engine?

Before you start working with the vibrating plate, you need to pour oil into its engine. Remember to check the oil level before starting the vibratory plate. Otherwise, your equipment will fail.

For engines running on Honda gasoline gx390, gx270, gx200, gx160, mineral motor oil with viscosity sae10w40 or sae10w30 is suitable.

There are also oils of other viscosities, but they may not be suitable due to the peculiarities of vibration technology, which can also lead to engine breakdown. It is best not to carry out any experiments, but to use the oil that is recommended according to the instructions for using the vibrating plate.

Changing the oil in the vibrating plate

So, first, the technique must be placed on a flat surface. Next, remove the cover from the hole where the oil will be poured. Fill in oil to the indicated mark and close the lid.

Now you need to start the engine for a couple of seconds and turn it off immediately. We check the oil level again. If it remains the same as before the launch, then you can start work.

The service “Vibratory plate rental in Minsk” will allow you not to worry about changing the oil: they will do it for you!

What kind of oil to pour into the vibrator of the vibrating plate

profitable model prices:

kind, vibrator, vibrating, plate

Vibratory plate 73 kg
Engine: Loncin

RUB 25,000

Vibratory plate 73 kg
Engine: Honda

37,500 rubles

Vibratory plate 85 kg
Engine: Honda

Until March 31, special offer!
Ordinary price: 46 00 rubles
Sales price: 43 500 rub

Until March 31, special offer!
Ordinary price: 50 00 rubles
Special offer: 47 500 rub

What kind of oil is in the vibrator of the vibrating plate

VIBROPLATES AND EVERYTHING FOR VIBROPLATES

Investro-M company. Sale of vibrating plates

favorable for models:

Vibratory plate 73 kg
Engine: Loncin

RUB 25,000

Vibratory plate 73 kg
Engine: Honda

37,500 rubles

Vibratory plate 85 kg
Engine: Honda

Until November 30 special offer!
Regular Price: RUB 46 00
Special offer: 38 500 rub

Until November 30 special offer!
Regular Price: RUB 50 00
Special offer: 45 000 rub

Vibratory plate 85 kg
Engine: Subaru

kind, vibrator, vibrating, plate

54,000 rubles

Vibratory plate 95 kg
Engine: Subaru

RUB 56,000

Vibratory plate 105 kg
Engine: Subaru

58,000 rubles

WE CARRY OUT DELIVERY OF VIBROPLATES!
ALL MODELS. 2 YEAR WARRANTY!

Checking Eccentric Weight Oil on Vibratory Compactor

VIBROPLATE OIL

What oil to use for vibrating plates

The vibratory plate has two mechanisms that require regular lubrication and oil control. It is a motor and vibration mechanism. Before starting the work of the vibrating plate, oil must be poured into the vibrator of the vibrating plate and into the engine.

As for the vibrating mechanism of the vibrating plate, oil is usually poured at the manufacturer’s plant. Since different factories use different types of oil for vibrating mechanisms, and, accordingly, there is no general oil change time for vibrators on vibrating plates, then when changing the oil, use the recommendations of the operating manual for your vibrating plate. It is best to use the services of your service center.

Oil is poured into the engine of the vibrating plate by the user himself before the start of operation. Be sure to check the oil level before starting each start, otherwise your engine may be damaged. For gasoline engines HONDA GX160, GX200, GX270, GX390 use MINERAL OIL FOR PETROL ENGINES (viscosity SAE 10W30 or SAE 10W40). Oil of other viscosities, due to the design features of the engine of the vibrating plates, may not reach the parts rubbing against each other, which will lead to rapid engine wear. Synthetic and semi-synthetic oils also have viscosities that differ from the recommended ones, therefore, for the durability of the engine operation, it is worth abandoning unnecessary experiments.

This type of four-stroke petrol engines on vibrating plates does not have special oil filters. Therefore, regular oil changes to remove contaminants that inevitably appear during operation are the key to successful and durable engine operation. The first oil change at the start of operation of the vibrating plate is carried out after 20 working hours. Then the oil is changed every 100 hours of operation or at the beginning of the working season, depending on the intensity of use of the vibratory plate.

vibrating plates

We recommend reading:

The vibrating mechanism and the motor are 2 mechanisms in the vibrating plate that need constant monitoring of the presence of oil and grease. Before starting to work with the vibrating plate, it is necessary to fill the engine and vibrator of the vibrating plate with oil.

If we talk about the vibration mechanism, then the oil is filled at the manufacturer’s plant. Each plant uses different types of oil, so there is no specific oil change date. Therefore, when you change the oil yourself, you must use the manual for the vibratory plate.

Vibratory plate 85 kg
Engine: Subaru

54,000 rubles

Vibratory plate 95 kg
Engine: Subaru

RUB 56,000

Vibratory plate 105 kg
Engine: Subaru

How often do you need to change the oil in the vibrating plate?

If the engine does not have oil filters, then you need to constantly change the oil, since dirt appears during operation. The oil should be changed after the first twenty working hours, and then every time after 100 hours. Also, if the vibrating plate has not been used for a very long time, it is worth changing the oil.

Technical service for Honda engines

Technical service of Honda engines on SPLITSTONE technique.

58,000 rubles

We do DOSTA VIBROPLATE!
What remains to be done for our client MODELS. WARRANTY 4.5 YEARS!

VIBROPLATE OIL

What oil to use for vibrating plates

The vibratory plate has two mechanisms that require constant lubrication and oil control. It is an engine and vibration mechanism. Before the vibrating plate starts to work, oil must be poured into the vibrator of the vibrating plate and into the engine.

As for the vibrating mechanism of the vibrating plate, oil is usually poured at the manufacturer’s plant. Because different factories use different types of oil for vibrating devices, and, accordingly, there is no general oil change time for vibrators on vibrating plates, then when changing the oil, use the advice of the management for the operation of your vibrating plate. Safer using the help of your service center.

Oil is poured into the vibrating plate engine by the user himself before operation. Before each start, be sure to inspect the oil level, otherwise your engine may fail. For gasoline units HONDA GX160, GX200, GX270, GX390, we use MINERAL engine OIL FOR Gasoline units (viscosity SAE 10W30, in other words SAE 10W40). Oil of other viscosities due to the vibration plate motor design technique may not reach the parts rubbing with each other, which will lead to quick wear of the motor. Synthetic and semi-synthetic oils also have viscosities different from the recommended ones; for the durability of the engine, it is worth refusing from unnecessary tests.

This type of four-stroke gasoline units on vibrating plates does not have special oil filters. Therefore, a constant oil change to remove contaminants that inevitably appears during operation is the key to successful and long-term operation of the motor. The first oil change at the start of the vibratory plate operation is done after 20 working hours. Then the oil changes every 100 hours of operation or at the beginning of the working season, depending on the intensity of operation of the vibrating plate.

We advise you to read:

What kind of oil is in the vibrator of the vibrating plate

Main road and construction machinery vibrating plates

  • EQUIPMENT
  • Vibratory plates
  • Seam cutters
  • Mosaic grinders
  • Multi-disc cutters
  • Roof cutters
  • Trowels
  • Crack Separators
  • DIAMOND TOOL
  • Cut-off tool
  • TURBO cutting discs for hand tools
  • Cutting discs SEGMENT for hand tools
  • Solid-edged cutting discs for hand tools
  • Cutting discs SEGMENT for machine cutting
  • Solid carbide milling cutters
  • Grinding tool
  • Frankfurt grinding
  • CO cutters
  • Polishing tool
  • Frankfurt polishing
  • Polishing Wheels
  • Drilling tool
  • Tubular drills
  • Drills with an ordered arrangement of diamonds
  • POWER ELECTRONICS
  • RECOMMENDATIONS, MATERIALS
  • Our Youtube channel
  • Vibratory plates petrol

    The vibrating plate is one of the types of specialized equipment for road construction works. designed for laying paving slabs, compaction of soil, various types of loose and cohesive surfaces: crushed stone, gravel, sand, asphalt. The most convenient machine for small volumes of this type of work. The vibrating plate allows compaction of the soil or road surface in those places where the roller cannot be used, on limited areas: paths, trenches. Vibratory plates are often used as a necessary addition to other, usually larger, road construction equipment.

    Vibratory plates, being a convenient and economical technique, are widely used today in various sectors of the economy: landscape design, road construction and repair, various areas of construction. Such machines can significantly reduce the amount of manual labor and significantly intensify the production of work.

    All models are compact and suitable for multiple transport.

    Vibratory plates, unlike vibratory rammers, have many times greater impact force.

    Vibratory plates SPLITSTONE make up 30% of the fleet of all vibrating plates in Russia.

    Modernization of our vibrating plates and equipping them with a new folding handle made it possible to accommodate a pair of removable wheels on it. Now the wheels removed from the base of the plate are securely attached to the handle and you can no longer worry about finding them at the end of the work.

    Vibratory plate range VS SPLITSTONE

    Vibrating plate
    VS-104
    Vibrating plate
    VS-134
    Vibrating plate
    VS-244
    Vibrating plate
    VS-245 E8
    Vibrating plate
    VS-245 E10-2
    Vibrating plate
    VS-246 E12
    Compaction Modes
    Crushed stone Invalid Invalid Permissible Permissible Permissible Permissible
    Soils (mixed soil, loam) Permissible Permissible Permissible Permissible Recommended Recommended
    Sand Permissible Permissible Permissible Permissible Permissible Permissible
    Paving slabs, paving stones (using a damping mat) Permissible Permissible Recommended Recommended Recommended Invalid
    Asphalt, asphalt concrete Permissible Permissible Recommended Recommended Permissible Permissible
    Specifications
    Slab working area width, m 0.29 0.29 0.41 0.41 0.50 0.43
    Dimensions (LxWxH), mm 995х320х835 1040x320x1000 1055x450x975 1170x450x955 1270x450x1030 1340x500x900
    Operating weight, kg (without water / with water) 55 70/80 89/99 111/121 128/138 141/151
    Compaction depth of bulk materials in 4 passes up to 95%, mm one hundred one hundred 200 210 200 250
    Forcing centrifugal force, kN eleven eleven 13.5 18.4 21.3 23.1
    Vibration frequency, Hz one hundred one hundred 93 93 93 80
    Movement speed on bulk materials, m / min 20-25 20 20-25 20-25 20-25 20-25
    HONDA engine, model GX 160 GX 160 GX 160 GX 160 GX 160 GX 160
    Engine power, kW (hp) 3.6 (4.8) 3.6 (4.8) 3.6 (4.8) 3.6 (4.8) 3.6 (4.8) 3.6 (4.8)
    Gas tank volume, l 3 3 3 3 3 3
    Fuel consumption, l / h 1.4 1.4 1.4 1.4 1.4 1.4
    Productivity, sq.m / hour one hundred one hundred 140 140 170 150
    Productivity, cub.m / hour ten ten 25 28 36 40
    Vibrating plate
    VS-245 E10
    Vibrating plate
    VS-246 E20
    Vibrating plate
    VS-309
    Compaction Modes
    Crushed stone Permissible Permissible Recommended
    Soils (mixed soil, loam) Permissible Recommended Recommended
    Sand Permissible Recommended Recommended
    Paving slabs, paving stones (using a damping mat) Recommended Permissible Invalid
    Asphalt, asphalt concrete Permissible Invalid Invalid
    Specifications
    Slab working area width, m 0.41 0.43 0.50
    Dimensions (LxWxH), mm 980x450x1010 1020x450x1040 1340x500x900
    Operating weight, kg (without water / with water) 128/138 159/169 300
    Compaction depth of bulk materials in 4 passes up to 97%, mm 220 300 400
    Forcing centrifugal force, kN 21.3 26.6 40
    Vibration frequency, Hz 93 80 72
    Movement speed on bulk materials, m / min 20-25 20-25 20-25
    HONDA engine, model GX 160 GX 200 GX 270
    Engine power, kW (hp) 3.6 (4.8) 4.1 (5.5) 6 (8)
    Gas tank volume, l 3 3 5.3
    Fuel consumption, l / h 1.4 1.4 2.5
    Productivity, sq.m / hour 140 160 180
    Productivity, cub.m / hour 32 fifty 72

    Now our vibratory plates are equipped with a new foldable, foldable handle with increased vibration resistance!

    The design features of our vibrating plates are:

    The principle of operation of vibrating plates

    For a better understanding of the principle of operation of the vibrating plate, you should consider its general structure. This unit consists of 4 main parts:

    kind, vibrator, vibrating, plate
    • steel or cast iron plate;
    • vibrator;
    • engine;
    • frame.

    The base of the mechanism is a massive slab lying at its base. In the center of this plate is a vibrator, on top of the engine. The engine communicates with the vibrator by means of a clutch and a V-belt transmission, through which rotational movements are fed to it. Already directly in the vibrator, these movements are transformed into vibrational ones. From the vibrator, the vibration is transmitted to the plate, and from the plate to the ground. Due to its mass and this vibration, the mechanism does the job. compacts bulk materials of different thicknesses and densities.

    Vibratory plates are equipped with a base made of cast iron or steel, engines are powered by electricity, gasoline or diesel fuel. Different models have different mass, vibration torque, engine power. All of this is discussed below.

    Tools

    The vibratory plate is a multipurpose construction tool that helps to effectively compact surfaces of fine and coarse soil, asphalt or sand. Also, the vibrating plate is indispensable for laying paving slabs and preparing the soil during the construction of the foundation. The advantages of a compact vibratory plate at home are its size, it allows you to work even in the most inaccessible areas, the area of ​​which makes it impossible to use an industrial roller for compacting the coating. The compact and convenient unit can be bought or rented. But, if you plan to work with a vibrating plate often, do it yourself. this is ideal.

    General characteristics of vibrating plates by weight

    The indicator of the mass of the plate is the most important when choosing a suitable model or when selecting parts for making a vibrating plate with your own hands. This indicator determines 70% of the productivity of the device and its compliance with the work performed. According to this indicator, the models of vibrating plates are divided into 4 classes:

    • Lightweight. weighing up to 75 kg;
    • Universal. with a mass of 75 to 90 kg;
    • Medium-heavy. weighing from 90 to 140 kg;
    • Heavy. with a mass of 140 kg.

    Lightweight models are optimal for work on the arrangement of adjacent territories, the maximum soil layer for these models is 15 cm.Also, these models are used for laying paving slabs, laying damping polyurethane mats on paths.

    Medium models are used for the partial repair of the asphalt roadway, laying tiles on the sidewalk, repairing the roadway after replacing the communications lying under them. The maximum soil layer for these models is 25 cm.

    Medium and heavy models do an excellent job with more serious tasks, for example, laying layers of road surface. With the help of vibrating machines of this category, the backfilling of trenches and the perimeter of the foundation of a low-rise building are compacted. The maximum soil layer for these models is 60 cm.The weight limitation of the vibrator for asphalt paving is 100 kg.

    In the selection of the optimal weight of the vibrator, special attention should be paid to the engine power. A weak motor on a heavy plate will not give you the expected productivity. Such a mechanism will sink into the soil layer and require additional efforts from the person performing the work. This discrepancy is especially acute in the models from the 3rd and 4th categories. When making or buying a vibrating plate, this ratio should be calculated. An example of a mismatch is a plate weighing 150-170 kg and a 5-6 hp engine. An example of the ideal ratio is 5 hp per 100 kg.

    • The principle of operation of vibrating plates
    • Scope of application of vibrating plates
    • General characteristics of vibrating plates by weight
    • General characteristics of vibrating plates by other criteria
    • Useful functional additions for the vibrating plate
    • Instructions: we do the vibrating plate ourselves
    • Rules for the operation of a homemade vibratory plate with a gasoline engine

    Instruction: we do the vibrating plate ourselves

    One of the most important reasons for making a do-it-yourself vibrating plate is the significant cost savings. The most inexpensive but reliable Chinese model will cost about 550 EUR, and the cost of a home-made car will not exceed 250 EUR. In addition, it is always a pleasure to work with your head and your own hands in order to ennoble your own home.

    The process of independent design and manufacture of a vibrating plate is quite simple, since this mechanism itself, by its design, is not very complex.

    Vibratory plate, spare parts for its assembly:

    • the engine is chosen at its discretion, for example, it can be an IV-98E platform vibrator operating from a 220 V network, the gasoline version is a three-stroke with one cylinder. Preferred model. Honda;
    • the basis for the platform is sheet metal, 8 mm thick and 45×80 in size;
    • channel. 2 pcs.;
    • soft elastic cushions are necessary for fixing the handle to the vibrating plate. 2 pcs.;
    • bolts M10 for an electric motor or M12 for a gasoline one;
    • plastic wheels. 2 pcs.;
    • pipe section;
    • hollow tube about 1.2 m long.

    Having collected everything you need, they begin to work, while the drawings of the vibrating plate do not need to be done:

    • Working with the engine. The cover is removed from it in order to be able to adjust the vibration force. only relevant for an electric motor.
    • An angle grinder is cut on a metal sheet. Distance from the edge. 10 cm, depth. about 5 mm. The incisions are made in the amount of two pieces on both sides symmetrically.
    • The edges are bent along the incisions with a hammer, the bending angle is 20-30o. This is to prevent the machine from being buried during operation.
    • The cuts are welded and the position of the ends is fixed. This work is not meaningless, since without pre-made cuts, it will be very problematic to bend the metal to the desired angle.
    • The vibrator is mounted on the plate using two channels. They are adjusted so that the edges do not protrude beyond the line of the working surface. At this point, welding is again required. Channel bars weld very well, the optimal position of the welding mowing line is across. Distance. 7-10 cm from each other relative to the center point of the plate and taking into account the position of the mounting holes on the engine.
    • M10 or M12 bolts attach the vibrator to the metal. Measure the distance between the mounting holes of the motor, drill holes at the same distance on the channels, fasten the motor to the base with bolts.
    • Elastic cushions and a pipe are required to make the handle of the vibrating plate. The handle is attached to the base through these pads to dampen vibration while the machine is running. This is very important, because if the vibration is not damped, the plate will begin to tear from the hands, and the vibrations will have a negative effect on the joints of the upper limbs.
    • To facilitate transportation of the slab, a piece of pipe is welded to it, on which the wheels are attached. The weight of the finished car will be about 60 kg, so this measure will not be superfluous. Wheels are fastened so that they can be easily mounted and removed.

    Useful advice for use: to damp vibrations during operation, they wrap the handle with a rope and make a loop out of it. During the performance of tamping work, they do not hold on to the handle itself, but to this loop, so as not to feel vibrations from the mechanism.

    General characteristics of vibrating plates by other criteria

    Additional data indicators include:

    • vibration force;
    • the size of the working surface;
    • engine power and type of fuel consumed by it.

    These parameters determine the density of the rammer, which the mechanism will eventually give, as well as the ease of operation and control. Now in more detail:

    • Vibration force. the vibration power level of the base of the mechanism. For dense soils and coatings, this indicator is selected as high as possible. Since weak shocks do not compact hard soil to the desired density.
    • The size of the working surface. this indicator determines the pressure of the plate per one unit of the processed surface. On a surface with a small area, this figure will be lower. This figure should not exceed 0.3. Conclusion. the smaller the working surface, the higher the efficiency of the vibrating plate. The highest indicator is for models with a cast iron base, for steel bases this figure is lower.
    • According to the type of fuel consumed, vibratory plates are divided into electric, gasoline and diesel. The petrol vibrating plate is recognized by the practitioners as the most convenient and in demand. The engine for this mechanism has a lower price when compared with a diesel one, and such a machine works in any conditions. The electric plate compactor has a lower cost than gasoline or diesel, while the power and performance are at the same level. The disadvantage is the need for access to power grids. As for diesel engines, these mechanisms are the most expensive, but the fuel for them is cheaper than for models with a gasoline engine. The disadvantage of a diesel stove is a high noise level.
    • The engine power determines the ability of the vibratory plate to move on a viscous surface and on a slope. The higher this indicator, the easier the car moves on the surface. The powerful motor pulls the plate forward by itself and does not require additional effort from the operator controlling the compaction. At low power ratings, the slab is buried in the ground, working downhill is especially problematic. The exception is models from the first weight class, in which the motor power and the weight of the plate correspond to each other.

    Scope of application of vibrating plates

    The main field of application of vibrating plates is the construction and repair of various levels of complexity, the laying of sidewalks and roads, the arrangement of sports grounds and much more. They are used both for industrial purposes and for private houses. The uniqueness of this mechanism is in its relatively small size and ability to cope in those conditions in which a conventional bulldozer will not be able to fulfill its purpose. For example, laying a sidewalk or garden path in a private house.

    With the help of a vibrating plate, concrete, asphalt, sand, gravel and ordinary soil on the lawn are tamped. Such a machine is indispensable for laying roads and sidewalks. The work of the vibrating plate is carried out even in trenches and narrow pits. Since such a complete set of the mechanism allows it to move in reverse, this greatly simplifies the work on the territory of a small area, where there is a need for frequent turns or overcoming obstacles.

    Vibratory plate Splitstone VS-134

    SPLITSTONE® CS JOINT CUTTERS

    The range of seam cutters provides the ability to cut structural and technological seams with smooth adjustment of the cutting depth up to 320 mm in asphalt, asphalt concrete, concrete, reinforced concrete and other materials. They are also used when cutting expansion joints, trimming the edge of the roadway, during patching of roads. The installation of gasoline and electric motors allows operating these machines in open areas and in closed rooms. The use of SPLITSTONE cut-off diamond discs for dry cutting makes it possible to work almost all year round even at negative ambient temperatures.

    Vibratory plate range VS SPLITSTONE

    VS-134 VS-244 VS-245 E8 VS-245 E10-2 VS-246 E12
    Compaction Modes
    Crushed stone Invalid Permissible Permissible Permissible Permissible
    Soils (mixed soil, loam) Permissible Permissible Permissible Recommended Recommended
    Sand Permissible Permissible Permissible Permissible Permissible
    Paving slabs, paving stones (using a damping mat) Permissible Recommended Recommended Recommended Invalid
    Asphalt, asphalt concrete Permissible Recommended Recommended Permissible Permissible
    Specifications
    Slab working area width, m 0.29 0.41 0.41 0.50 0.43
    Dimensions (LxWxH), mm 1040x320x1000 1055x450x975 1170x450x955 1270x450x1030 1340x500x900
    Operating weight, kg without water with water 68 78 84 94 100 110 100 110 132 142
    Compaction depth of bulk materials in 4 passes up to 97%, mm one hundred 200 210 200 250
    Forcing centrifugal force, kN eleven 13.5 18.4 21.3 23.1
    Vibration frequency, Hz one hundred 93 93 93 80
    Movement speed on bulk materials, m / min 20-25 20-25 20-25 20-25 20-25
    HONDA engine, model GX 160 GX 160 GX 160 GX 160 GX 160
    Engine power, kW (hp) 3.6 (4.8) 3.6 (4.8) 3.6 (4.8) 3.6 (4.8) 3.6 (4.8)
    Gas tank volume, l 3 3 3 3 3
    Fuel consumption, l / h 1.4 1.4 1.4 1.4 1.4
    Productivity, sq.m / hour one hundred 140 140 170 150
    Productivity, cub.m / hour ten 25 28 36 40

    VS-245 E10 VS-246 E20 VS-309
    Compaction Modes
    Crushed stone Permissible Permissible Recommended
    Soils (mixed soil, loam) Permissible Recommended Recommended
    Sand Permissible Recommended Recommended
    Paving slabs, paving stones (using a damping mat) Recommended Permissible Invalid
    Asphalt, asphalt concrete Permissible Invalid Invalid
    Specifications
    Slab working area width, m 0.41 0.43 0.50
    Dimensions (LxWxH), mm 980x450x1010 1020x450x1040 1340x500x900
    Operating weight, kg without water with water 120 130 150 160 300
    Compaction depth of bulk materials in 4 passes up to 97%, mm 220 300 400
    Forcing centrifugal force, kN 21.3 26.6 40
    Vibration frequency, Hz 93 80 72
    Movement speed on bulk materials, m / min 20-25 20-25 20-25
    HONDA engine, model GX 160 GX 200 GX 270
    Engine power, kW (hp) 3.6 (4.8) 4.1 (5.5) 6 (8)
    Gas tank volume, l 3 3 5.3
    Fuel consumption, l / h 1.4 1.4 2.5
    Productivity, sq.m / hour 140 160 180
    Productivity, cub.m / hour 32 fifty 72

    Structural features of SPLITSTONE vibrating plates are:

    Range of mosaic grinders GM SPLITSTONE

    GM-122G GM-122 (2.2) GM-122 (4) CGM-124 (4)
    Frankfurt. a special tool for MSM
    Processing zone width per pass, mm 300 300 300 300
    Number of traverses of the machine one one one
    Plan-washer rotation frequency, rpm 1200 500 1000 600
    Engine Honda GXV 340 Petrol Electric
    Engine power, kW (h.p.) 6.6 (8.9) 2.2 (3.0) 4.0 (5.3) 4 (5.3)
    Current type / voltage / frequency Single phase,
    220 V, 50 Hz
    Three-phase, 380V, 50Hz
    Operating weight without load / with load, kg 95
    110
    96
    126
    96
    126
    120
    Dimensions (LxWxH), mm
    workers / transport
    1020x600x1020 965x580x1055
    665x580x635
    965x580x1055
    665x580x635
    1050 x 600 x 1050
    Approximate productivity, when grinding concrete M300 with an average removal of 1 mm2 / hour 12 four 8 5-30 times more

    GM-245 (5.5) GM-245 (7.5) GM-2411 (11) GM-4811 (11)
    Frankfurt. a special tool for MSM
    Processing zone width per pass, mm 600 600 600 1200
    Number of machine traverses 2 2 four four
    Plan-washer rotation frequency, rpm 600/1000 1200 600/1200 600/1200
    Engine Electric
    Engine power, kW (h.p.) 5.5 (7.3) 7.5 (10) 11 (15) 11 (15)
    Current type / voltage / frequency Three-phase, 380V, 50Hz
    Operating weight without load / with load, kg 152
    182
    148
    178
    260
    290
    236
    294
    Dimensions (LxWxH), mm
    workers / transport
    1410x650x1140
    700x650x765
    1410x650x1140
    700x650x765
    1470 x 710 x 1025 1410 x 1250 x 1140
    Approximate productivity, when grinding concrete M300 with an average removal of 1 mm2 / hour 14 20 35 35

    Vibratory plate Splitstone VS-246 E12

    Vibratory plate Splitstone VS-246 E20

    SPLITSTONE® CR ROOF CUTTERS

    Designed for cutting soft roofs, removing soft upper layers of old roofing. compressed roofing material, glassine, bitumen, slag wool or other heat-insulating materials. Equipping roof cutters with gasoline and electric motors allows them to be used in various conditions. Special SPLITSTONE cutters with hard alloy inserts are used as cutting tools on roof cutters.