What kind of oil to fill in a single-axle tractor Salute

Oil in a single-axle tractor Salute

Oil for engines of Salute walk-behind tractors, recommended by manufacturers. The frequency of changing the oil in the engine of the walk-behind tractor Salute extracts from the instructions. For more details on what oil to fill in the engine of the walk-behind tractor and cultivator, see the corresponding page of the site. Since the load on ball and roller bearings, chains, etc.

Thanks to oil, the area of ​​application of the force increases and the force is distributed over this area, so that it is prevented from concentrating at one point.

The oil film covers metal surfaces, preventing them from coming into contact with oxygen in the air. Piston rings seal the gap in the piston pair for better use of high combustion pressure.

The oil helps to better seal. Soot and deposits accumulate in the oil and are carried away by it, which prevents the formation of stubborn deposits on engine parts. The oil in the hydraulic torque transmission clutch acts as a medium for smooth and even power transmission. On the contrary, the oil in the shock absorber serves to absorb impact energy.

Site `s map. SAE 10W oil is recommended for use at all temperatures.

If you wish to use a seasonal oil, select an oil with the appropriate viscosity grade based on the average temperature in your area. Air cooled engines heat up faster than car engines. Using non-synthetic thickened oil 5W, 10W, etc.

The first 5 hours. Change oil. Every 8 hours or daily. Check the oil level.

Oil change on a walk-behind tractor Salute with a Lifan engine

Competent maintenance and operation of the Salute walk-behind tractor helps to extend the service life and improve the characteristics of the equipment. Reducer and motor-block engine. one of the most important structural elements.

Land cultivation equipment operating manuals

The most reliable recommendations will be those offered by motorcycle manufacturers. Let’s refer to the user manuals for the Salyut-5 and Salyut walk-behind tractors. User’s manual for the Salyut single-axle tractor. download.

To prevent oil spilling from the gearbox, engine crankcase and fuel from the engine fuel tank, a single-axle tractor should be installed on the vehicle in its normal operating position during transportation. Check the oil level in the walk-behind tractor gearbox as follows: The most widely presented motoblocks Salute with the Chinese engine Lifan F-2B with a capacity of 6.5 liters.

How and how much to pour oil into the gearbox of the Salute walk-behind tractor

Every 50 hours or every season. Change oil. Checking the oil level. with every use.

Change of oil. the first month or after 20 hours of work, thereafter. every 6 months or every hour of operation. Change of engine oil: First change after 20 hours of operation; afterwards. every operating hours.

Maintenance features

In the design of the walk-behind tractor, the main elements are the gearbox and the engine. Each user needs to know what kind of oil and with what frequency to fill in and replace if necessary. The most correct will, of course, be the manufacturer’s recommendations.

The first time the oil should be changed after 25 hours of operation of the device, subsequent times can be less frequent. after every 100 hours of operation of the walk-behind tractor.

The gearbox must be filled with 1.1 liters of oil through a special hole, and its level must be checked with a special dipstick. Oil TM-5-18 (TAD-17I) should be used.

Let’s take a closer look at how to pour oil into the gearbox of the Salute walk-behind tractor. It is very important that the engine is turned off. First, you need to put the uniaxial tractor in a horizontal position, move the speed lever to “reverse” and open the gearbox oil drain plug. Insert the dipstick there until the handle rests. Then remove it and check the oil level. It should be between the two marks. If the oil is less than the lower designation, it must be topped up. The used oil is drained from the gearbox through the drain pipe.

Salute 100. an inexpensive workhorse

Of the large assortment of agricultural machinery, one of the most popular in the domestic market is the Salyut 100 single-axle tractor, on board which there is a Lifan 168F-2B engine with a capacity of 6.5 hp.

the single-axle tractor Salyut 100 is versatile, so it can perform a variety of tasks. Let’s clarify what capabilities the Salyut single-axle tractor has. For example: mowing hay, removing snow, pumping out water, plowing the land, hilling a vegetable garden, harvesting potatoes and even transporting at a speed of 10-12 km. various loads. It all depends on which attachment to attach to it.

single-axle tractor Salute. overview of features

Motoblocks Salute are manufactured at the Moscow Machine-Building Production Enterprise, which develops military-industrial equipment and is popular not only in its homeland, but also far abroad. The sad news is that since 2014, the production of this equipment has been moved from Russia to China.

The developers did not engage in prototyping, but created their own concept of motoblocks with a number of distinctive characteristics. The main difference is that the center of gravity of the Salute walk-behind tractor is low enough, and the engine is brought forward. Thanks to this, this unit can be operated with minimal effort.

Separately, it should be said about engines: all models are equipped with four-stroke gasoline internal combustion engines from Russian, Japanese, American and Chinese manufacturers.

Technical characteristics of Salyut 100:

  • Lifan 168 F2 air-cooled four-stroke engine.
  • Engine 6.5 HP with a capacity of 3600 rpm in min.
  • Consumes one and a half liters of fuel per hour.
  • Holds 3.6 liters of fuel.
  • There is a gear reducer.
  • The width of the milling cutters is 35, 60 and 80 cm with the possibility of further increasing.
  • Working depth. up to 25 cm.
  • Adjustment of the steering wheel in 2 planes, horizontally and vertically, with the ability to fold for transportation.
  • It is possible to install attachments.
  • The weight of this unit is 78 kg.

the single-axle tractor Salyut 100 is unpretentious in operation, and working with it will turn from exhausting work into a feasible task even for a schoolchild. But do not neglect his maintenance, because it will significantly prolong his life.

What to do if the Salyut single-axle tractor does not start?

Before starting the device, you need to make sure that the throttle and reverse connections, as well as the clutch, are secure. The cables should move smoothly without undue force.

Most often, a single-axle tractor will not start after a long period of inactivity, for example, after a winter. There may be several reasons. The main ones are oxidation of contacts, problems with wire insulation, clogged carburetor jets and watering of fuel or oil. Insufficient amount of the second can also be the reason. With old oil, smoke and exhaust gases of a characteristic white color may emanate from technology.

After checking and starting the unit, you can go directly to work with the Salute walk-behind tractor. If the soil is quite hard and the weight of the walk-behind tractor is not enough, then you can use special weights on the wheels, which are shaped like a vessel and covered with wet sand, pebbles or something heavy to increase the mass. They are fastened using conventional bolts, which are usually supplied in the kit.

It is advisable to use weighting agents when plowing the land, hilling plants or harvesting root crops. In addition, they are installed on cultivators.

single-axle tractor Salute. oil into the engine, into the gearbox

Oil in the gearbox of the Salute walk-behind tractor

Oil poured into the gearbox of the Salyut-5, 100 motorcycle TM-5-18 (TAD-17I)
The amount of oil poured into the gearbox of the walk-behind tractor, l 1.1
Oil change intervals the first time in 25 hours, then every 100 hours,

Fill the gearbox of the walk-behind tractor with oil through the oil filler hole of the gearbox. The gearbox must be filled with 1.1 liters of TM-5-18 (TAD-17I) oil, check the level with a dipstick.

kind, fill, single-axle, tractor, salute

To prevent oil spilling out of the gearbox, engine crankcase and fuel from the engine fuel tank, a single-axle tractor should be installed on the vehicle in its normal operating position during transportation.

ATTENTION! Before each start of work, check the engine oil level as indicated in the Engine Operator’s Manual. Pay particular attention to the safety precautions when starting the engine as indicated in the Engine Operator’s Manual. Work on a walk-behind tractor with a closed or half-open air damper is not allowed.

Maintenance after the first 25 hours of operation:

Work to be performed after every 100 hours of operation:

Checking and filling oil in the gearbox of the Salute walk-behind tractor

ATTENTION! Work on replacing and measuring the oil level in the gearbox of the walk-behind tractor should be carried out only with the engine off.!

Fill the oil in the gearbox of the walk-behind tractor through the oil filler hole of the gearbox. Check the oil level in the walk-behind tractor gearbox as follows:

0.85 l (180 mm from the edge of the oil filler hole), and the top risk

1.1 l (125 mm from the edge of the oil filler hole);

kind, fill, single-axle, tractor, salute

Oil in a single-axle tractor Salute

Competent maintenance and operation of the Salute walk-behind tractor helps to extend the service life and improve the characteristics of the equipment. Reducer and motor-block engine. one of the most important structural elements. What kind of oil to fill in the gearbox and motor-block engine, as well as the frequency of its replacement, volume. this is the data that every owner of such equipment needs to know.

The most reliable recommendations will be those offered by motorcycle manufacturers. Let’s refer to the user manuals for the Salyut-5 and Salyut walk-behind tractors. 100.

Official website of the manufacturer of motoblocks Salute. www.salut.ru

User’s manual for the single-axle tractor Salute. Download 100

Oil in the engine of the Motoblock Salute

The most widely presented motoblocks Salute with the Chinese engine Lifan 168F-2B with a capacity of 6.5 hp.

The engines of other well-known world brands are also used:

Japanese Robin Subaru EX. 6 hp.

CHANGING FRONT AXLE OIL ON TRACTOR

American Briggs Stratton Vanguard 6.5 series PRO. 6.5 hp.

Chinese Hwasdan H170F. 7 hp.

Oil for engines of Salute walk-behind tractors, recommended by manufacturers.

Motoblock engine make Manufacturer’s Recommended Engine Oil
summer winter service class
Robin Subaru (Subaru) SAE 10W-30. in temperate climates SAE 5W-30. in cold regions Automotive engine oil; class SE or higher (SG, SH or SJ recommended)
Honda (Honda) SAE 10W-30 is recommended for use at all temperatures. If you wish to use seasonal oil, select the appropriate viscosity grade based on the average temperature in your area. SG, SF.
Lifan (Lifan) SAE-30 SAE-10W-30. all-season
Briggs Stratton (brigs) Briggs Stratton recommends the use of synthetic oil when operating in temperatures below 0 ° C. If you do not have synthetic oil, you can use Briggs Stratton 10W-30 non-synthetic oil, part number 998208 Note: Synthetic oil that meets the ILSAC GF-2 certification mark, API and API service symbol labeled “SJ / CF ENERGY CONSERVING” and above can be apply at any temperature. Change synthetic oil as usual. Air cooled engines heat up faster than car engines. Using non-synthetic thickened oil (5W-30, 10W-30, etc.) at temperatures above 4 ° C will result in high oil consumption. If using such oil, check the oil level more often. SF, SG, SH, SJ or above
DM-1-01 (JSC Kaluga Engine) М63 / 12Г1 or М53 / 10Г1 GOST 10541-78, oil corresponding to API requirements: SF; SG; SH and SAE: 10W30; 15W30
DM-1K Instruction from OJSC “Red October” M10GI, M12GI TU 38.10148-85 M63 / 12G1 or M53 / 10G1 GOST 10541-78,

The frequency of changing the oil in the engine of the Salute walk-behind tractor (excerpts from the instructions)

Briggs Stratton (brigs) First 5 hours. Change oil. Every 8 hours or daily. Check oil level. Every 50 hours or every season. Change oil.
Honda (Honda) Lifan (Lifan) Checking the oil level. with every use. Change of oil. the first month or after 20 hours of work, thereafter. every 6 months or after 100 hours of operation
Robin Subaru (Subaru) Checking the level and adding engine oil. each time the engine is used (add oil to the maximum mark). Engine oil change: First change after 20 hours of operation; later. every 100 hours of operation

For more details on which oil to fill in the engine of the walk-behind tractor and cultivator, see the corresponding page of the site.

Reduced friction between moving parts

Since the load on ball and roller bearings, chains, etc. acts at one point or across the surface, a large force is applied at that point. Thanks to oil, the area of ​​application of the force increases and the force is distributed over this area, so that it is prevented from concentrating at one point.

Oil cools rubbing surfaces, removing heat generated on them.

The oil film covers metal surfaces, preventing them from contact with atmospheric oxygen.

Piston rings seal the gap in the piston pair to better exploit the high combustion pressure. Oil helps better seal.

Soot and deposits accumulate in the oil and are carried away by it, which prevents the formation of stubborn deposits on engine parts.

The oil in the hydraulic torque transmission clutch acts as a medium for smooth and even power transmission. On the contrary, the oil in the shock absorber serves to absorb impact energy.

Transmission

The clutch in the Salyut-100 BS-V walk-behind tractor is due to a reliable V-belt transmission. If one belt breaks, the operation of the unit does not stop.

Commercial Vehicle Weight Limit

The gearbox of the Salyut 100BS-V walk-behind tractor is gear-type, which means it is distinguished by its reliability, durability with a motor resource of more than 3000 hours. It has the highest efficiency among gearboxes, provides minimum power losses and practically does not require maintenance. Due to its quality, it is possible to use various motors.

In this model of Salut, the speed switch is moved to the steering wheel, so there is no need to bend over to engage the required gear. The clutch handle is designed so that when pressed, resistance is felt, and in the pressed position against the handle, the holding force is minimal. Thanks to the adjustment of the handle in 2 planes, it is possible to optimally adjust the walk-behind tractor for any user.

Oil level control TM 5-18 (TAD17I) is carried out with a special dipstick. another characteristic innovation in the design of the walk-behind tractor.

The power take-off pulley of the Salyut 100 BS-V walk-behind tractor is the middle stream of the driven pulley, it is used for mounting external trailed implements, including stationary ones.

The frame of the walk-behind tractor is made in the form of two steel squares with the main units and mechanisms fixed on it.

Cutters

The real pride of the walk-behind tractor, like all hundredths of the Salutes, are the three-row sickle-shaped cutters. Forged knives are made of high quality spring steel. Cultivation width. 360-800 mm depending on the number of cutters.

Wheels

Pneumatic wheels with expressive tread are installed on the shaft, used when working with installed units and to move the walk-behind tractor.

Specifications

Brand: Firework
Ripping width: Over 60 cm
Loosening depth: Over 20 cm
Engine make: Briggs Stratton
Working volume of the cylinder, cm: 205
Rated power at working speed, kW / (rpm): 4.8 / 3600
Fuel tank volume, l: 3.8
Transmission type (reducer): Mechanical (gear)
Transmission, forward movement (number of speeds): four
Transmission, reverse movement (number of speeds): 2
Cultivator type: Attachments (plow, hiller, catrofel digger, snow plow, pumping unit, etc.)
Number of cutters: 6
Cutter diameter, cm: 32
Driving wheels: there is
Adjustable handle: there is
Wheel diameter, mm / inches: 400/15
Weight, kg: 98
Working width, cm: 30/60/98
Working depth (max.), Cm: 25
A type: Gasoline
Guarantee: 1 year
Producing country: Russia / China

Description

The design and operating principles of the Salyut 100 BS-V are similar to the 100 L6.5 model.

  • Powerful Briggs Stratton Vanguard engine (USA).
  • It has a gear reducer, two forward gears, thanks to which Salute can easily cope with any task.
  • Large pneumatic wheels provide increased flotation even on difficult terrain.
  • Economical fuel consumption allows the walk-behind tractor to work smoothly at one gas station for a long period of time.
  • The advantageous feature is the underestimated center of gravity, which greatly facilitates maneuverability, handling and work in general.
  • Works stably in areas with a medium slope.
  • single-axle tractor has compact dimensions. with removed wheels and steering it can be conveniently placed in the trunk of a car.

Coulter

The position of the opener bar (included in the package of the Salyut 100 BS-V walk-behind tractor) adjusts the depth of soil cultivation. With a greater deepening of the bar, the processing depth is correspondingly greater. within 100-250 mm.