Which chains fit the Husqvarna 135 chain saw
Areas of use
From the first glance at the Husqvarna 135 chainsaw, it is clear that it is not designed for serious tasks, but it can do the job in the yard or on a construction site. The Husqvarna 135, has several technical solutions that aim to make it easier to use. For this reason, sawing with a chainsaw can not only men, but also women, of course, only after they are carefully acquainted with the instruction manual.
The saw is well suited for roofing work, t. ะบ. it has low weight and is easy to start, which is important when working at height. You can also use the saw for work in sawmills, where you need the saw to trim limbs or cut slack. For light-duty jobs like this, the Husqvarna 135 chain saw is easy.
It is very noteworthy that this model is popular among those who do figure wood carving with a chainsaw.
Husqvarna 135 Specifications
Adjusting the carburetor ensures the correct ratio of fuel and air to the engine combustion chamber. Before you start adjusting the carburetor, you need to:
- Check the air filter. Often clogging of the filter causes interruptions in the work of the chainsaw (such cases are more than 50% and a simple cleaning saves from unnecessary adjustment of the carburetor);
- Make sure that the fuel-oil mixture is properly prepared. The ratio of gasoline (we advise to use 95 or high-quality 92) to oil should be between 1 to 50 and 1 to 40. Use only high-quality fuel and oil! At any service center, they’ll tell you that most chain saw problems are caused by poor-quality fuel. Problems with the chainsaw‘s idle speed or rpm when working in that number.
- Make sure the fuel-oil mixture was not prepared earlier than 7-10 days ago. The mixture that has been prepared for a long time is gradually degrading. Mix fuel in small containers.
- Check chain tension. An overstretched chain can inhibit the bar from running dry.
If all the conditions are met, you may start adjusting the carburetor. This is done by using the idle speed adjustment screw so that the chain does not move at idle speed. The adjusting screw should be turned carefully about 1/16th of a turn to catch the moment when the saw’s power is at its highest but idle speed is not cranking. If you have any problems, please contact our service center.
With the Husqvarna 135 chain saw, you get just about everything you need for use and self-service. The model’s basic package includes:
- 16″ long guide bar, 3/8″ chain pitch and 1.3 mm groove width;
- 16″ long bar and 3/8″ chain pitch H37;
- instruction manual;
- combination wrench for dismantling parts and do-it-yourself repairs.
How to Fit the Bar and Chain on a Husqvarna Chainsaw
No tools for resetting the saw element are included in the scope of delivery. Because of this, chain sharpening must be carried out with the help of handy tools by the operator.
Husqvarna 135 chain saw. a basic model, which has a low weight and is very convenient for home use for sawing wood, making firewood, performing such garden work as trimming limbs and branches, carrying out work with wood in construction and other.
Husqvarna 135 chain saw is the latest generation of low-emissions saws. The tool has a two-stroke gasoline engine with 1,500 watts of power. Engine cylinder volume is 40.9 cc.see. Engine is designed with X-Tord technology for economical gasoline-oil mixture consumption and reduced emissions.
A video about sawing wood with a Husqvarna 135 chain saw:
The Husqvarna 135 differs from the Husqvarna 140 in the following ways:
- The 135 has a quick mount for the air filter;
- The power of the 140 model is 1600 watts, the 135 is 1500 watts;
- Another difference is the price, the 140-th Husqvarna chainsaw is more expensive than the 135-th.
Both are “standard” or “regular” saws, according to the manufacturer. Excellent for domestic use and ordinary woodworking tasks, have similar technical characteristics, namely. the same engine displacement, bus length. The 140 model consumes 930 ml/hr, compared with 1.1 ml/hr for the 135.
X-Torq 2-stroke gasoline engine is the backbone of the chainsaw. Its function is to reduce the amount of unburnable fuel in the exhaust fumes. The essence of this technology is quite simple, and, at the same time, the most effective.
After fuel ignition in the X-Torq cylinder, the piston lowers. During this process a bypass opens, allowing clean air to flow directly into the cylinder. This technology releases recycled gases from the cylinder as clean air. Thus, the engine consumes an order of magnitude less fuel.
The Husqvarna 135 features a proprietary forced-air circulation system called Air Injection for engine cooling. It consists of a durable air filter that’s easily accessible, allowing you to quickly replace a worn element. A device that distributes the airflow using a centrifugal system completes the filter.
The Husqvarna 135 16 chainsaw is equipped with a 2-chamber carburetor, which is also found on the 440 model from the Swedish manufacturer. The tool is equipped with a hand pump for pre-pumping fuel in cold start mode.
To control the main mechanisms of the model, its device provides gas and brake levers, as well as a throttle position switch. All controls are on the back of the chain saw, in close proximity to the operator’s hands.
H37 guide bar and chain with 3/8″ pitch and 0.05″ guide bar mounting slot are responsible for cutting wood. Bus length for installation should be 35-45 cm.
The Husqvarna 135 has a momentary inertia brake for stopping the bar and saw chain in an emergency. It is turned on and off with a separate knob. For operator safety, the tool also includes a shield that protects the operator’s right hand.
Highlights of the Husqvarna 135 include a vibration-reducing LowVib system. It consists of several rubber-metal dampers that absorb the vibrations of the motor as it runs.
All of the Husqvarna 135’s internal parts and mechanisms, as well as its fuel and oil reservoirs, are housed in a rugged plastic enclosure. It can withstand falls from a low height and light impacts against hard objects.
How to use the Husqvarna 135 Gasoline-Powered Chain Saw instruction manual
Instruction manual is the chain saw’s constant companion from the manufacturer to the customer. It contains the following information:
- Husqvarna 135 features.
- The Husqvarna135 chain saw is equipped with.
- How to assemble a chainsaw with descriptions.
- 135 Features.
- Safety Precautions.
- Sawing techniques and methods.
- Preparing and starting up a Husqvarna 135 chainsaw.
- Running-in of chain saw.
- Maintenance.
- Troubleshooting.
Accessories
- Husqvarna 135 chain saw;
- 56-link saw chain;
- 40 cm long guide bar;
- A guide bar cover;
- universal screwdriver;
- A container with chain oil.
Why this model has won the trust of users?
The Husqvarna 135-16 utility-status saw, equipped with a 2-power carburetor engine and a productive 16-inch cutting attachment, matches the characteristics of semi-professional chainsaws in many operating features.
Model’s simple design makes it easy to repair. A wide range of spare parts allows you to quickly troubleshoot or make necessary repairs on your own.
The chainsaw manufacturer’s specifications are consistent, in every respect, with its performance capabilities. Numerous positive reviews from owners of this model bear witness to this.
Husqvarna 135 chain saw
General features chainsaw Power 1500Wmodification 9677880-02 40 cm bar length 3/8″ chain pitch Weight 4.4 kg
Adjusting carburetor
Traction and fuel economy depend on properly tuned fuel system. Operation involves preliminary cleaning of air inlet and warming up of engine to working temperature. Carburetor adjustment is done in a prescribed sequence by turning quantity and quality screws.
Factory tuning is based on averaged parameters, so it needs to be adjusted for external factors. A properly tuned engine is characterized by good injectivity, rpm stability in all modes, absence of increased smokiness and detonation noise.
If the adjustment does not give the desired result, you should verify the quality of fuel, the absence of water condensation in the carburetor, the cleanliness of nipples, the presence of the spark plug in the ignition gap recommended in the instructions.
Chain for Husqvarna 135 16 chainsaw
The name of the company producing the goods. Our webshop sells products from time-honored manufacturers. Almost all of them have an extensive network of service centers not only in Russia, but in other cities as well.
The country where the manufacturing company is headquartered. In today’s globalized world large companies locate their production facilities not only at home. Factories can be located anywhere in the world.
Further information on Picco Micro Comfort 3 saw chain
Low-vibration low-profile saw chain, high output like a standard chain, but less kickback. Intended for light chainsaws. Ideal for all users who appreciate power and comfort. Saw chain is great for cutting thin wood, limbing, and maintenance work with the proper saws.
Features of Picco Micro Comfort Saw Chain 3
German saw chains are known for their technical innovations and high manufacturing quality. Here are some convincing quality indicators.
Chain extraction
Delivery in Moscow and Moscow region
Delivery within the Moscow Ring Road. from 400 per MKAD. 30/km.
Goods priced at 30 000 and more are delivered for free within MKAD (Moscow outer ring road).
Self-delivery
You can pick up the goods yourself at our store at the address:
Delivery within Russia
Delivery by transport companies.
Delivery to the terminal of the transport company in Moscow. 200.
Delivery cost for your region is determined by the carrier chosen by you.