Which Plow Is Best For A Tiller

How to choose a good plow for what you should pay attention to : Which plow is better for a tiller to choose Double-sided plow for a tiller Photo of a plow for a tiller Plow zykov for a tiller How to make a plow for a tiller

Rotary plow

A rotary plow for a tiller is compared to a metal comb, which makes it possible to plow the soil. These types of plows of different models can be different in shape. However, these models are united by the fact that their shape expands towards the top, which allows these units to dump soil away from the trench.

When choosing a plow, it is necessary to take into account the presence of a tiller plow setting. It is necessary to be able to adjust the depth of cut and the angle of inclination, for more efficient work with the plow.

The device of the plow Zykov

  • -share on the unit body;
  • -a stand that helps to attach the technique to the tiller;
  • -field board (gives stability to the model);
  • -support part;
  • -feather to turn the soil and get a more evenly cultivated arable land.

2.4 How to set up the plow on the tiller: installation, fastening, adjustment

It is necessary to install the finished implement on the cultivator using nuts. But, at first, for convenient adjustment, they should not be fully tightened. Then, with the help of two steel pins, we fix the unit to the fastening shackle. The installed unit can now be adjusted.

It is important to adjust the finished unit so that the plowing quality is as good as possible. To do this, at the beginning, you need to balance the height of the tiller, and with the help of bolts set and fix the angle of inclination of the apparatus parallel to the ground.

The adjusted unit with handles reaches the belt. Adjustment of the tiller plow ends with control plowing, in which the distance between the dumps of the earth is no more than 8-10 cm.
To the menu

Preparation of parts and assembly of a homemade plow for a tiller

This model has many modifications, blueprints and adherents. The tiller plow for dummies usually describes the design of a single-body plow. No special tools or skills are required to make it. Even a beginner in mechanical engineering can cope with this model.

Tiller-mounted single-body reversible plow

You will need rollers and steel up to 4mm thick to make the blades. We cut out the shape by welding or with ordinary scissors, and simply bend it in the shape of a cylinder on the rollers. There is an option when the dumps can be made from a piece of pipe or cylinder, with a diameter of 500 to 600 mm, with a thickness of no more than 5 mm.

To do this, the shape must be cut out by welding, rubbed with emery, and, if necessary, as in that long-forgotten anecdote, carefully brought to mind with a hammer. Then you will need to make other parts of the future unit.

Thus, according to the drawings, you need to make 6 parts:

  • Steel share or disc;
  • Spacer plate;
  • Side shield for the rack;
  • A plate for the base of the plow itself;
  • Field board with an angle of 30X30 millimeters;
  • Pipe for a rack 42 mm in diameter.
which plow is best for a tiller

Then, using wedges, we install the finished share (on the auxiliary sheet), fasten it with two-point welding, and join the stand with the side shield so that the shield is 7-9 mm higher than the share, and the edges of the shield go over the edge of the blade by 6-7 mm. All parts are welded to each other again.

Then you need to weld the blade so that it becomes a single whole surface with the share. If the angle between the blade and the ploughshare is more than 7 degrees, they need to be finished with a hammer. So, the blade is welded to the share, the share to the side shield. Now we attach the side shield first to the base plate and then to the spacer bar.

The share corners are welded to the base plate last. Then we separate the auxiliary sheet, clean up the welding marks, and grind the share with the blade with sandpaper.
To the menu

Parameters

The parameters of the mini-transports are important, and the types of tiller varieties also depend on them.

Hyundai T 2000E

Ideal for light work. This device is a pleasure to work with. The design is comfortable. The model itself is designed specifically for the cultivation of land, so cultivating the land with this tiller is the best option.

The main advantage is a high-quality motor and a large width of cutters. All at a low cost.

There were no drawbacks to this model.

Dde V900 II Minotaur

Tiller of excellent quality from an American company, made in China.

Such a device has a gear transmission, which makes 4 gear speeds available in use.

The device of the plow Zykov

  • -share on the unit body;
  • -a stand that helps to attach the technique to the tiller;
  • -field board (gives stability to the model);
  • -support part;
  • -feather to turn the soil and get a more evenly cultivated arable land.

Rotary plow

A rotary plow for a tiller is compared to a metal comb, which makes it possible to plow the soil. These types of plows of different models can be different in shape. However, these models are united by the fact that their shape expands towards the top, which allows these units to dump soil away from the trench.

When choosing a plow, it is necessary to take into account the presence of a tiller plow setting. It is necessary to be able to adjust the depth of cut and the angle of inclination, for more efficient work with the plow.

Double sided plow for tiller

A double-sided tiller plow (hiller) is used to huddle various crops. It also removes weeds between the rows. Such plows can work the soil, cut furrows to plant the plants, and then fill them up, including the back of the tiller. Such devices differ only in width of capture. Fixed and variable. The only difference between them is in the movable wings, which regulate the working width.

The plow, which has a fixed working width, works with a light tiller (up to 30 kg), the engine of which is up to 3.5 HP. Their feature is 12-millimeter stands (protect the tiller from overloading).

The most common type of hillers with a variable working width. Their only drawback is the soil shedding into the furrow after the pass. Such plows come with tillers over 30 kg, with engines of 4.0 hp. And higher.

Articles , , ,