Why did a trimmer for the grass began to work poorly. When a trimmer for grass does not pull

Why does a trimmer for grass do not gain full power

A braid braid with a gasoline drive is a necessary thing to owners of personal plots, lawns, and when a trimmer for grass stalls at one moment, the work on cleaning the area from the grass stops.

The device itself is a rather difficult mechanism, because there are many different circumstances of its breakdowns. As a rule, the emerging problems contain an annotation for operation.

Know the prerequisites for why the trimmer stalls for the grass, it should be that without the help of others to perfectly perform the repair of the device.

Problems with a benzocosa associated with the purpose that this device is not started, specially classified by specialists of service services. They stand out malfunctions with such nodes of the mechanism:

• The engine, in which the piston and bearings can be worn out or out of order, crack the crankcase;
• The fuel supply system, with all this, can be clogging the filter or interfering with the carburetor;
• Mechanical damage to wires, tubes, hoses;
• The ignition chain.

In order to correctly find the knot where the breakdown occurred, you need to study in what circumstances the trimmer stalls for the grass.

If the lawn mower stops when pressing the gas, then the prerequisites are usually subsequent.

• The more increased option is a carburetor adjustment failure that appears with significant load loads after a long.term inaction of the mechanism or when using it in languid criteria.
• The clogging of the fuel valve, which eliminate it with the message, and as a result, gasoline according to the system begins to flow normally.
• The weakening and hanging of the cable in the carburetor. There is also a tensile of the fuel hose directly to its gap, caused by the action of a significant load.
• The clogging of the soundtress (revolutionary valve), for this reason, does not enter the fuel in the tank.

The lawn mower stalls in other words suffocates when pressing the gas

If the inconsistent is associated with the carburetor node, then it can be recognized when the lawn mowing appears when the vibrations appear. When a hose bursts or a cable stretches, a change of data data is made.

When a braid for grass stalls at large speeds, this is due to the following problems:

• Clogging or clutching the valve placed on the gas tank lid;
• The carburetor was drained under the influence of vibrations that occur during the operation of the mechanism;
• Obstacles with the circulation of fuel consistency;
• Atmospheric air
• The hose created to fuel fuel cracked or slightly connected.

The carburetor is regulated by focusing on the operational annotation to the trimmer. For the option, it is often enough to weaken the tightness of its body. If there are problematic issues with the circulation of the fuel consistency, then it can gradually enter the carburetor. After its production, the engine stalls at huge speeds.

At single speeds, all.fought trimmer stopping the grass are subsequent:

• Reducing the speed of the gearbox when heating it, which is a consequence of the use of inappropriate fuel consistency;
• Clogging of the throttle;

• Air entering the system;
• Insufficiently fuel at the work of a lawn mower.

Read lubricant for a gearbox for Husqvarna grass

If a carburetor is a problem place, then the technique will stop at the “cold” and with a “hot” launch.

The unit can stall immediately after starting, if the carburetor is resolved as it was also called incorrectly configured. this causes an uneven supply of fuel. The result will be that the device begins to vibrate clearly. To eliminate problems, the carburetor is reconfigured, acting by annotation to the mechanism.

When pressing gas

If the lawn mower stops when pressing the gas, then the reasons may be the following.

• The most common option is Carburetor adjustment failure. which occurs with significant loads on the drive, after prolonged inaction of the mechanism or when using it in severe conditions.
• Flaw valve clogging. which eliminates it with the message, as a result of which gasoline according to the system begins to flow normally.
• The weakening and hanging of the cable in the carburetor. It can also arise Stretching of the fuel hose up to its break, caused by the action of a significant load.
• The clogging of the sapun (check valve), as a result of which fuel does not enter the tank.

If the problem is associated with the carburetor node, then it can be recognized by the appearance of vibrations of the lawn mower

Когда лопается шланг или растягивается трос — выполняют замену данных комплектующих.

The lawn mower stalls

When buying a chainsaw, you should be prepared for the fact that, like all such tools, damage may occur that will require repairs.

But do not immediately run to the service center and pay a lot of money to the masters, convincing them of a serious defect in the device.

The lawn mower stalls at high speeds

Probably, the most common complaint about gasoline trimmers for grass is as follows: “The gasoline lawn mower jams”.

The reason for this, of course, may be a sufficiently serious malfunction. The engine of a two.stroke trimmer for grass does not develop turns and ceases to rotate. The FS 130 gasoline lawn mower gives gas and stops. However, in most cases, the situation is even simpler than it seems at first glance.

What to do with such a misfortune, first try to deal with its causes without the help of others, because, having found the reason, it’s even easier to cope with the trouble, and sometimes it is even self.destructive.

In fact, circumstances, that is, when gasoline burns at high speed, there are many.

Why is a Chinese lawn mower not developing momentum?

Trimmer for grass does not gain speed. a very common malfunction, which, of course, does not always have a regular solution.

The lawn mower is not gaining momentum, the cause of the malfunction and eliminate it

The first launch of new gas stations.Removing the grid from the silencer, began to work.

Another factor is the occurrence of failures in the energy system.

In this case, a braid for grass will stop at idle. At idle, the main secateur stops. GoodLuck 4300 chainsaw stops at idle video. The lawn mower stops when you press the accelerator pedal. The gasoline lawn mower is turned off at high speed. Problems with the power system can be caused by improper carburetor adjustment or incorrectly adjusted carburetor.

Excessive adjustment can be caused by vibration that occurs during the operation of a braid for grass.

However, an incorrectly adjusted chainsaw can be corrected by adjusting it in accordance with the recommendations of the user’s management.

In addition, sometimes gasoline trimmers for grass can be jammed due to the fact that the valve in the lid of the fuel tank just clogged or clogged.

To check this, try starting a trimmer for the grass by unscrewing the fuel tank cover.

If the device works fine in this mode, clean the valve.

Some tricks of work with a benzotrimer.

Now is summer, and gasoline engines have become a constant attribute on land plots. Great tool, powerful and mobile. You can mow grass with a gasoline trimmer and cut dry weeds. But sometimes the braid for grass does not start, works with interruptions or does not develop full power. Now, of course, is not the time to work! As they say, this is rather the vibration of the starter handle than the kosba.

Problems with the launch do not only have an old braid for grass, but also in the new. what is the answer? Only one thing remains. listen to expert advice and adopt their practical experience.

Ways to eliminate breakdowns

Subsequent work is likely on the carburetor:

• cleaning and adjustment of the fuel supply valve;
• similar work with a valve producing redesigned gases and pairs (after burning fuel);
• replacement of the spring more weak on the entrance valve;
• restoration of the tension of the carburetor cable;
• replacement of the fuel leaks hose, verification and strengthening of a weakened connection;
• changing the rotor damper disk;.
• Change of faulty wire or ignition coil.

Immediately after the start

Smelting Motokos or a trimmer for the grass after starting is justified by subsequent reasons:

• impressive of previously adjusted valves;
• first the wrong settings of the valve mechanism;
• clogging with deposits of the fuel supply valve;
• the hose is worn or poorly annexed.

Due to the violated method of injection of a fuel, a lawn mower or a trimmer for grass is very vibrated in work.

When pressing gas

If the lawn mower stops when pressing the gas, then the reasons may be the following.

• The most common option is a fuss of adjusting the carburetor, which occurs with significant loads on the drive, after a prolonged inaction of the mechanism or when it is used in severe conditions.
• The clogging of the fuel valve, which eliminates it with the message, as a result of which gasoline according to the system begins to flow normally.
• The weakening and hanging of the cable in the carburetor. Also, a tensile of the fuel hose can occur up to its rupture, caused by the action of a significant load.
• Clogging of the saapun (check valve), as a result of which fuel does not enter the tank.

If the problem is associated with the carburetor node, then it can be recognized by the appearance of vibrations of the lawn mower. Когда лопается шланг или растягивается трос — выполняют замену данных комплектующих.

The gasoline trimmer for the grass starts and stalls

Why is a trimmer not starting for grass gasoline? Reasons and their elimination

Recently, a gasoline trimmer for grass has acquired the status of one of the main tools in the arsenal of summer residents. And this is not surprising, because a motorized braid for grass allows you to quickly put a personal plot in order. However, sometimes it happens that the trimmer for the grass does not start hot and even on cold. In such situations, you have to independently establish the cause of the malfunction. Let’s find out what to do if a trimmer does not start for grass. The reasons that most often lead to such troubles will be considered further.

Diagnostics strategy

Where to start the diagnosis of malfunctions if a trimmer is not started for grass? In situations where the tool stalls immediately after starting, it is worth examining the following units:

It is the breakdown of the above locations that most often leads to the fact that a trimmer for grass is poorly started. Let’s look at how to eliminate such troubles.

Checking the fuel mixture

Suppose you don’t start a trimmer for grass. In this case, the first thing is to check whether the fuel is enough in the tank, as well as evaluate the quality of the fuel mixture. To refuel a motorized unit, it is necessary exclusively high.quality gasoline. It is recommended to use fuel, the brand of which is not lower than AI-95. Refueling a trimmer for grass with fuel of unknown origin, not bought at a gas station, is fraught with frequent failures in the work of the tool. This can cause a breakdown of the cylinder-piston system. Repair in this case often exceeds the cost of the device itself.

Why is a trimmer not starting for grass gasoline? Incorrect preparation of the fuel mixture may also lead to this, which consists of oil and gasoline. The proportions in which the specified components are connected are indicated by manufacturers in the guide for the operation of a trimmer for grass. Preparing the fuel mixture is extremely not recommended in large volumes, that is, for the future. Indeed, with prolonged savings, there is a loss of the determining properties of the substance. Therefore, if a trimmer for grass does not start, it is worth draining the old fuel and use freshly prepared fuel mixture.

Read which trimmer for grass is better than rotary or vibration

Diagnosis of the candle channel

What to do if the used fuel mixture is in perfect order, but a trimmer for grass is still not started by gasoline? The reasons for the refusal of the mechanism may lie in excessive moisture of the candle channel. To diagnose and eliminate the problem, it is necessary to do the following:

• To twist the candle. Wipe it thoroughly, and then dry it.
• Drain excess fuel in the chamber through the corresponding candle hole.
• Clear the old candle if there is a dozen on its surface. Cope with the task will allow the use of a conventional ladies’ nail file or file.
• When installing the element in place, set a gap of 1 mm. To check the parameter, it is enough to place any coin in the lumen.
• Collect a functional block back.
• Try to start a trimmer for grass.

It is recommended to perform a candle channel to dry for at least half an hour. However, in no case should you resort to the calcination of its elements. After all, heating the spark plug can lead to its final corruption. Что предпринять, если обслуживание функционального блока было выполнено в соответствии вышеуказанным рекомендациям, но триммер для травы не заводится, искра есть при этом? In this case, it should be treated with gasoline threaded connection. The latter does not need to be saturated abundantly fuel. It should only be slightly moisturized. Resort to such actions should be to ensure the ignition. After all, no matter how much the candle gives a strong spark, in an absolutely dry chamber there simply will not be something to ignite.

The lawn mower stalls

Carburetor adjustment, well start

,stalling when pressing gas. My Skype: Ork.Vitek tel. 380979677418

The lawn mower stalls or suffocates when you press the gas

Even more information about the repair and choice of tools on our website www.Looktool.Ru, we are happy for everyone.

If even in this case a trimmer for grass does not start, it is worth evaluating the quality of the contact between the high.voltage wire and the candle. In the absence of a spark (in the presence of a reliable connection between the indicated elements), most likely, the problem is caused by breakdown of the ignition unit. In this situation, you will have to turn to the services of masters who will reinstall the knot.

Checking filters

Another common cause, due to which a trimmer for grass does not start, is the presence of a blockage in the filter area. To confirm the conjecture, just dismantle the indicated block and try to start the unit without it. If the engine of the trimmer for the grass has launched, most likely you will have to replace the air filter or at least perform a thorough purge of the old. In the presence of abundant contaminants on the surface of the filter element, it is necessary to use a new grid. Relying to such actions, you should not leave a suction pipe at all without a filter. After all, rush in this case can lead to the need to repair the entire piston group of the unit engine.

Cleaning the soundtress

Often the engine of branded models of trimmers stalls as a result of clogging of the soundtress. The main task of the specified component is to align the pressure in the fuel tank. In the case of contamination of the node, a vacuum is formed here, which significantly complicates the supply of fuel. Eliminating the malfunction allows the cleaning of the saapon using a conventional sewing needle.

Diagnosis of the graduation channel

The stable functioning of a trimmer for grass can be impaired as a result of laying dirt in the graduation canal or the formation of a blockage on a muffler grid. This problem most often occurs during the operation of older generation trimmers. The issue is being solved by dismantling the anti.diploma mesh and its cleaning.

How to prevent sudden breakdowns during the operation of a trimmer for grass?

So that the unit is always in a functional state, it is worth observing several simple rules:

Preventive measures and operating rules

So that the lawn mower does not work and does not stall when starting, it must be correctly stored and operated. Compliance with the following simple recommendations will forget about problems.

• When begging the grass, you need to monitor the state of the cooling system. It is also necessary to regularly clean the channels in the case and starter’s ribs.
• To clean the tool, you should use kerosene, solvent, or other washing tools.
• You can not clean a hot tool. it must cool before washing.
• It is important to observe the recommended working mode. this will avoid overheating of the engine.

To store the tool in cold weather, you need:

• completely drain the fuel;
• disassemble the lawn mower, wash and clean all available components;

• inspect the condition of the parts, eliminate all defects that can be corrected;
• pour the required amount of oil into the gearbox;
• Clean the air filter;
• perform partial disassembly of the engine, wash all moving parts, blow and lubricate thoroughly;
• To lubricate the piston, unscrew the candle, then raise the piston to the upper dead point by the starter, pour a small amount of oil into the hole for the candle and do the crankshaft several times.

Important! If there is no way to store a trimmer for grass in a warm dry room, you must first wrap the motor with an embarrassed rag.

Only by observing these rules, you can be sure that the lawn mower will work properly and will not stall for a number of seasons.

As you can see, stopping the work of a trimmer for grass can be caused by many reasons. Most of them can be fixed independently using the user instructions. In cases where there is no self.confidence, the equipment is recommended to be attributed to repairs. It is worth remembering that incorrect actions can cause even greater harm to the trimmer. As a result, the repair of Motokos will cost a much larger amount than it would be initially, and in the worst case, it may be necessary to buy a new unit.

Why is a benzotrimer not gaining momentum and strangle

A braid braid with a gasoline drive is a necessary thing to owners of personal plots, lawns, and when a trimmer for grass stalls at one moment, the work on cleaning the area from the grass stops. The device itself is a rather difficult mechanism, because there are many different circumstances of its breakdowns. As a rule, the emerging problems contain an annotation for operation. Know the prerequisites for why the trimmer stalls for the grass, it should be that without the help of others to perfectly perform the repair of the device.

Problems with a benzocosa associated with the purpose that this device is not started, specially classified by specialists of service services. They stand out malfunctions with such nodes of the mechanism:

In order to correctly find the knot where the breakdown occurred, you need to study in what circumstances the trimmer stalls for the grass.

If the lawn mower stops when pressing the gas, then the prerequisites are usually subsequent.

• The more increased option is a carburetor adjustment failure that appears with significant load loads after a long.term inaction of the mechanism or when using it in languid criteria.
• The clogging of the fuel valve, which eliminate it with the message, and as a result, gasoline according to the system begins to flow normally.
• The weakening and hanging of the cable in the carburetor. There is also a tensile of the fuel hose directly to its gap, caused by the action of a significant load.
• The clogging of the soundtress (revolutionary valve), for this reason, does not enter the fuel in the tank.

What to do if the chainsaw does not throw off the moment?

The opposite previous situation is the one when the gas tools very quickly reaches high capacities and does not slow down. In this case, it can be observed that neither a screw on the case, nor cleaning the carburetor, this is not to eliminate. It would seem what else is needed, the saw works, gives out power as in the instructions. But the trouble is that in this case, in this case, you need ten times more than usual.

Read trimmer for grass gasoline stalls at high speeds the reason

If the gasoline on the candle of the chainsaw is fixed, and the cutting device itself does not work normally, then this indicates an excess of the air fuel mixture. The reason for this condition may be a failure in the adjustments of the carburetor, clogging of its jacklers, as well as the incorrect start of the mechanism. In the case of fixing on a candle characteristic soot, it is possible to talk with sufficient confidence about the incorrect functioning of the carburetor or the use of low.quality gasoline.

With all the above signs reflected on the spark plug, it is necessary to remove the carburetor and check its technical condition. Carburetor, when clogging, should be thoroughly cleaned, then adjust the device according to the technological requirements and replace the gas used in the tank. It should always be remembered that the carburetor is a rather complex node, consisting of many small components, details and tubules. Therefore, its repair should be carried out with particular caution and accuracy.

In addition to the restoration of the carburetor, it is necessary to check on the stand and the performance of the spark plug itself and, if necessary, set the correct gap in it. If the candle and its work do not like it at all, it is recommended to replace it with a new candle.

When opening an air damper

It happens that the unit stalls when opening an air damper, working normally at idle. This is due to the air leaks of the system caused by the presence Cracks of the fuel hose

or problems with seals. The carburetor dosing system can also work malfunctioning, while the lawn mower will stop after the opening of the damper.

All possible reasons that the lawn mower stalls, and the methods of eliminating them are contained in the next video

There are many reasons for stopping Motokos, but the most commonly occur in work related to its carburetor. They can arise in any case. The most problematic option is when there is a serious breakdown, and you will need to purchase new parts or change the lawn mower.

So that the trimmer for the grass works normally for a long time, you should strictly comply with the requirements of the operating instructions. It is necessary to refuel the unit suitable for it in the composition with a fuel mixture, the device should work with a moderate load.

Low quality fuel use

The benzotrimer does not gain speed in case of poor.quality fuel. He may stop or not start at all. To check the quality of the fuel, you need to inspect the candles. They are the main indicators for solving problems with the combustion chamber.

In the presence of sediment, a raid, plaque, the old fuel merges, and another, high.quality.

or gasoline cutter should be filled with good quality gasoline and the fuel brands that the manufacturer indicated in the technical passport of the device.

For your information! Candles should be thoroughly cleaned of plaque, and only after that they are again placed in the combustion chamber.

Electric trimmer for grass vibrates

Many mowing users noticed that some time after the start of the apparatus, it begins to vibrate very much. On some trimmers, mainly in models more expensive, an anti.vibration system was installed in the form of shock absorbers seized between the engine and the bar. But in some cases, even she does not save from strong vibration. The reason that strong vibration appears in the trimmer, there may be a small amount or complete absence of lubrication on a hard or flexible shaft located inside the rod of the apparatus.

Replacing the lubrication of the hard shaft is as follows:

• unscrew the gearbox located at the bottom of the bar;

• After removing the gearbox, you will see the end of the shaft, for which you need to pull to extract the part;

• after extracting the shaft, it must be abundantly lubricated with a special lubricant “Shrus-4” or ordinary-“Litol-24”;
• Apply a small amount of lubrication to the shaft and evenly smear it along the entire length of the part, including the slots at the ends of the rod (if they worked, the shaft will have to be replaced);
• After lubrication, insert the shaft back into the bar and put the gearbox in the same place.

The lubrication of the flexible shaft is as follows:

• unscrew and remove the mowing head;
• remove the bar from the electric motor by unscrewing a couple of bolts;
• Pull out a flexible cable from the bar;
• Lubricate the cable with grease along the entire length.

This is done like this: first you need to lubricate the end of the cable, and then insert it into the bar, after which, as it moves into the pipe, you should apply grease to the part and evenly distribute it on the surface. Then insert a bar with a flexible shaft into an electric engine and fix it.

In the event that the lubricant did not help, and the vibration continues to appear, you will need to change the flexible shaft.

DIY lawnies repair: analysis of malfunctions and methods for their independent elimination

Repair of the lawn mower in artisanal conditions: analysis of defects and methods for their independent elimination of gas.

The subsequent step will be the repair of the carburetor, where you will have to find a malfunction and remove it, given the tiny sizes of the details. If simple operations did not bring results in order not to violate the narrow setting of the complex of accounting programs, it is better to entrust the repair of the repair. Where to start diagnostics and how to correctly carry out the repair of the lawn mower on your own, check out

Why stall the engine of a trimmer for grass when recruiting

The most popular with summer residents, gardeners and gardeners trimmers for grass are equipped with two.stroke engines operating on gasoline. In recent years, part of the manufacturers have been promoting motorcycles and leaflets based on four.stroke engines in the market, but they have not yet gained the popularity that two.stroke. They are more difficult in the device, more demanding on the mode of operation, purity of fuel, oil quality. Also, four.stroke engines are more in weight and more slowly gaining momentum.

During the operation of trimmers on the basis of two.stroke engines, a number of characteristic malfunctions arise related to the features of the design of the engines. With all the perfection of the Husqvarna or Echo engines, even they occasionally “acting up”. The budget models of motorcycle assembled in China, problems arise more often. This is due to both the lower quality of materials and the assembly level. The most characteristic malfunction is a poor launch from a “hot” state and “subsidence” of revolutions at a slight load. But sometimes a trimmer for grass stalls with a sharp press on the throttle key. Why does this happen?

The reasons for the breakdown

For all the apparent simplicity, the lawn mower is a well.thought.out and balanced tool in which each part is in its place. If everything is regular, the engine from the cold state should start after the first starter jerk. Depending on the model, first you need to swing the fuel mixture by pressing the transparent button on the carburetor. In a number of modern fuel pumping models, it is not required.

You also need to transfer the lever on the carburetor to the extreme position to close the air damper. In some models of Husqvarna and other manufacturers, the shuttle of the damper is carried out by turning a special regulator. After that, you need to turn on the ignition on the handle and energetically pull the starter’s cord, while pressing the gas key to about half.

The engine should start after the first jerk, but can earn after 3. 4 movements. This cannot be considered a breakdown. it all depends on the production of the motor, the quality of the fuel mixture, temperature and humidity and other factors. Two.stroke engines have their own character, to find out why they are not launched from the first, but from the fourth time, it is difficult even for professional mechanics.

If the engine confidently launched and earned, but the trimmer for the grass stalls when pressing the gas, then you forgot to transfer the carburetor lever to the position of the open or partially open air damper. Usually. this is the movement of the lever down. It may happen that the most stable the lawn mower works with a not fully opened damper. If you have used the trimmer for more than one season, so it will be. When the lever of the damper is transferred to the extreme lower position, the fuel mixture can become too impoverished and the trimmer for the grass stalls when you give gas.

This feature is not considered a malfunction. you just need to check the work of the trimmer for grass in different modes and try to use the optimal one in work. But there are other reasons why the lawn mower can stall at any stage, immediately after starting or during operation.

Other possible reasons

If, with a sharp addition of revolutions, the engine stalls, as if zabulae, then the reason may be:

• Carburetor adjustment failure. This happens after prolonged downtime or after excessive loads, for example, natives in hot weather or in conditions of strong dustiness.
• Clogging valve on the tank cover. Eliminated by replacing the lid or cleaning valve.
• Weakening of the cable of the carburetor regulator drive.
• Stretching of the fuel hose.
• Depressurization of traffic jams on the tank, which includes hoses.
• The clogging of the sapun.

When looking for the reasons why the trimmer stalls for the grass when trying to increase speed, other reasons may appear, for example, associated with the ignition coil and candle. If the fuel mixture is not prepared according to the rules using cheap oil or poor.quality gasoline, the proportions are not observed, or the mixture cooked a month ago, then the engine can also stall when trying to add gas.

How the real reason is determined

In the case when the carburetor is responsible for stopping the engine, a sudden stop is accompanied by a nearby symptoms. Most often, this is the appearance of tangible vibrations in all operating modes. Carburetor adjustment is carried out using two screws. idle control and fuel supply. In which direction to rotate them should be written in the operating instructions. If independent adjustment has not helped, contact the service center or buy a new carburetor.

If you have a lawn mower of a professional or semi-professional class, for example, the same echo or al-ko. then the carburetor resource is approximately equal to the durability of the motor and there is no need to buy a new one. It is enough to seek help in adjustment to a knowledgeable specialist. Motokos type Champion has a slightly lower carburetor resource, it may happen that adjustments will not help. Carburetors of two.stroke engines in the repair are complex, so it is better to order a new.

After making sure that the carburetor works fine, but the lawn mower still stalls, try to loosen the gas tank cover. If the engine operating mode has changed, it means that the lid valve is clogged or clogged. Practice shows that it is useless to clean it. It is better to buy a new cover, it costs a little, and it will last at least 2. 3 seasons.

Along the way, check the tightness of the gas pipeline connection from the carburetor and tank. Sometimes hoses stretch, and air is sucked around around the fittings. With a sharp press on the gas key, the mixture becomes depleted (gasoline is less than a stichiometric indicator) and the motor stalls. This also happens when the gasket between the carburetor and the cylinder is pierced or the bolts of the carburetor attachment are loosened from vibration. Just in case, check them, but do not forget that two.stroke engines are made of rather fragile alloys. If you overdo it with the moment of puffing, the thread in the cylinder can be disrupted.

It is also recommended to check the fence mesh on the hose in the tank, the cork through which the hoses are inserted into the tank and blow the fuel lines. Perhaps they are clogged and a little gasoline enters the carburetor. Especially with sharp pressure on gas.

Having checked and cleaning all the systems of a trimmer for grass, season the tank prepared by all the rules with a mixture and start from a cold state. Let me work out a few minutes at idle and try to mow fishing at medium speeds. After 10. 12 minutes of work, add speed sharply. a trimmer for grass should not stall. If this happens, change the spark plug and perform the same actions.

If during operation a trimmer for the grass, before stall, spontaneously periodically reduces or increases the revolutions, “failures” appear in power, then it is necessary to check the ignition coil and contacts of all wires. Start with contacts, they are quite fragile and can break off or oxidize.

How to look for malfunctions in the mechanical part

The transmission of rotation from an electric trimmer for grass is performed in the same way as models with an internal combustion engine: an integral shaft works inside the rectangular section of the bar, and a curved cable works.

Their length, diameter and design are selected by the manufacturer for specific dimensions of the composite bar.

Features of the junction of the composite bar

It is made by an adapter with a screw clamp.

The large screw head is made to conveniently adjust the position of the mowing organ at the bottom of the bar. The rotation angle is selected individually.

It is convenient for me to expose it so that the longitudinal axis of the protective casing and the axis of the electric motor are located in the same plane.

In this place, a malfunction associated with the transfer of torque from a direct shaft to a cable may sometimes occur in this place. It is manifested by the fact that at idle engine the trimmer for grass works normally, and already under a small load, the mowing head stops rotating.

The method of its elimination was well shown by the owner of the video “Repair of the Electrimmer” Roman Shapkov. I recommend to see.

Method of attaching a mowing head and a casing

On my trimmer from below the rod, the adapter is fixed with rivets, into which the fastener bolt of the protective casing will be plunged.

The output shaft of a rotating cable has a hexagon at the end. A plastic mowing head is put on it.

From the inside, a return spring of the automatic discharge of fishing line during kosbe is inserted into it.

A spool was inserted into it. It is fastened with a fixing nut from above.

The device of a spitter head with a fishing line is quite simple.

However, all plastic parts do not have high strength, subject to wear. Their working surfaces are erased. After three seasons of work on my trimmer, the output holes of the fishing line from the mowing head expanded, the thickness of the fixing nut decreased.

It is difficult to apply protective measures to wear, and repair of these parts is easiest to fully replace the head. It is easy to buy it: you just need to know the exact dimensions of the hexagon and evaluate the new design according to the working characteristics.

The secrets of the selection of fishing line

Among the frequent malfunctions of the trimmer coil, there are cases when the fishing line for the trimmer ended or simply confused due to improper winding on the spool. It is not difficult to eliminate them.

But in practice, I met with another defect in the fishing line, which was sold on the state retail chain from Patriot LLC company. Her view in the factory packaging.

As I understand it, it is specially hidden in a sealed package: you can not touch when buying.

When I opened the packaging to install the fishing line in the spool, its plasticity immediately caught my eye, and not elasticity. It is easily bending, behaves like a soft wire: when in contact with the grass, it immediately breaks. It is impossible to mow: she managed to return to the seller.

Since then, I have been buying only that fishing line for a trimmer that can be molested in my hands and evaluate its operational properties.

I try to refuse varieties of ordinary round fishing line. I prefer a ribbed shape to them with faces: asterisk, trapezoid, square or triangle. They are better cut off the grass.

How to eliminate increased vibration

Reliably collected trimmer mechanics for grass is well balanced. It provides convenient work. However, bearings can be worn out over time, lose lubrication.

A prefabricated shaft transmitting rotation from the engine of a spool is able to touch the internal walls of the bar, creating excessive friction with heating.

Such a defect can and must be eliminated. This technology is shown by TV repairman with his video “Vibration during the operation of Elektokosa”.

If you still have questions about how to carry out the repair of the electrimmer, then ask them in the Комментарии и мнения владельцев. I will answer.

Subscribe to our “Home Master” newsletter and you will always learn the first about the news of this blog!

Комментарии и мнения владельцев

Elena :

The Eletric trimmer has broken for the Carver TR1200S grass. a plastic hexagonal planting nest on a semi.automatic burst melted and a square screw from a fixing nut flew out of overheating (although they didn’t mow 10 minutes). We cannot choose a similar rogue of another brand. On some site, the man was advised: since the landing size M10x1.25 is the left (although they did not find something in the instructions), the head from Husqvarna 5310060-93 may approach the instructions. But she stands like a new trimmer for grass.What do you advise?

Alexei :

Hello, Elena. Do I understand correctly that you have a new trimmer for the grass and broke down after the purchase? The fact is that in this case the manufacturer’s guarantees act in this case. On his website https: // mcgrp.ru/Manual/Carver/TR-1200S specially looked at the instructions for your model. There is also a forum for users where they ask any question about products and share information. I advise you to discuss this issue with the manufacturer. He values ​​a reputation and should help you. Phone Central Service Center: 7 (342) 218-24-85. I believe that picking up a mowing head by size of mounting is not entirely right. The reason for overheating you did not find out. Twisting transmissions may not coincide. About information in the instructions: it is created for buyers in order to familiarize yourself with the device and operating rules. The drawings of all the details in it do not publish.

Elena :

PAUL :

Tell !pzhl.,How to strengthen the latch (in your text it is called: connecting adapter with a screw clamp) in the connection of the collapsible straight bar, spanks from vibration, does not fix it.

Alexei :

Hello, Pavel. On my trimmer, this knot was made by plates, which are riveted at the turn of the turn, and then the usual screw mount. Everything is simple there. How is your trimmer for grass, this node is difficult to judge. Maybe you will take a picture at least on the phone and send a picture to the mail? Address in the section “On the site”, “Privacy Policy”. See the very bottom.

Sergey :

If the lock is twisted, and there is a supply of a supply on the screw, then the countrogais will help.

Dmitry :

Huter Get-1500SL. The engine rotates slowly. Even if you remove the trimer bar, and pull the engine out of the case, then the rotation is slow, and some strange sound is noticeable. The bearings are good, the lubricant in the nodes is present, the brushes are normal (but by the way they are so tightly settled by the anchor that it is difficult to rotate it with your fingers) the winding is like a whole, everything is visually good. Separately, everything is spinning normally. But when everything is collected, it feels like a bearing died, or a skew. I sin on mechanics, but separately everything is working, and if you collect, it barely twists

Alexei :

Dmitry, hello. Try to rotate a completely assembled engine with your hands, and then pull out the brushes and repeat the operation. Without brushes, rotation should be easy, inertia is felt. If it is not, then there are two options: somewhere there is a place for rubbing the rotor on the stator or clinked some kind of bearing. You need to inspect all this very carefully, especially the lubricant. There may also be some kind of garbage in it. In a word, check the rotation for inertia and by ear. Evaluate all places, look at the lumen. Turn on the voltage only in extreme cases and measure idle currents preferably without nozzles. Compare them with a nominal load.

Michael:

I can not unscrew the bolt of mounting mowing

Alexei :

Michael, they came to me on the mail of the site of your bolt. I’ll try to tell the solution. And it’s very difficult to give recommendations.

Paul :

The spit.head on email constantly flies.trimmer ET 1000 at the junction with a flexible shaft. I can’t understand how it is attached in a bent bar?

Alexei :