You can cut the interior door in height. How to cut an interior door

16th December 2022

What interior doors can be cut in height. How to correctly cut the canvas of the interior door

If you had to cut the doors after installing the loops, this means that you incorrectly determined the dimensions of the box relative to the canvas, or made a mistake with the loops. In the latter case, it will be more correct to correct the error. Before installing the doors on the hinges, make sure that the dimensions of the canvas are shorter than the gap of the box by about 10 millimeters, and it is already 4-5mm, and the lines of the canvas and the bouts are parallel. At the same time, you can make sure that the vertical stand of the box from the side of the loops is perfectly even. this is very important.

Sometimes the question arises. how to shorten the door after a laminate or parquet that was not indesposed earlier. The network is full of descriptions, how dashing installers are controlled with this operation using a end circular saw. We recommend that you do not follow such tips. If you can allow such an operation in relation to the door from the wood.fiber plate, then the veneer of valuable woods will most likely be spoiled. The difficulty is that even the smallest teeth of the saw will tear out particles of veneer, forming chips and creases, it is no longer possible to fix such a marriage.

However, carefully cut the doors in height is quite possible. In Runet, this is advised to do this using a powerful manual electrophoresis and the guide line. The method is real, only dust is in a pretty dust, and a figured overhead decor does not always allow you to reliably fix the ruler. It is easier to do this operation using an electric rhubank, professional installation of doors without this tool does not do. In particular, a competent carpenter with the help of an electric rhuban forms on the vertical part of the canvas facing the hinges, a corner slightly different from 90 ° and open towards the narthex. As a result, the loops in a closed state are also slightly ajar, which removes all the stresses between the box and the canvas.

Before cutting, remove the canvas from the hinges and glue the painting tape on the bottom of the door. This is done in the case of the operation by a milling mill. the tape will prevent chips and protect the varnish from scratches that are possible in contact with the instrument platform.

Before cutting the doors with an electric rhinoma, apply a fishing line for a trimmer with a pencil on a painting tape, according to which you will navigate. Do not bring the lobs to the opposite end so as not to put it, remove the layer by a layer on both sides of the canvas. Try to install the doors on the hinges, not yet reaching a pencil label. cutting off the excess, you will have to put up with too much lower clearance.

The best solution is to entrust the work to the master, representing a well.established company. Attention to your problem in combination with professional skills will be a guarantee of a successful result.

How to correct the interior door

Each person, buying a door, hopes that it will not have to be repaired for a very long time. For this, many people order doors from professionals to be confident in their quality. But there is nothing eternal in life, and repairs in the apartment are an inevitable action. After you install linoleum or laminate on the floor, the interior door, by definition, will begin to close poorly and open, since the height of the floor has increased. Therefore, you will need to cut the door so that it opens freely, and does not creak. If you leave the solution to this problem for later, you can simply ruin the door. And do not forget that buying a new model will be expensive, because no one has extra money now.

Want to saw off the door from below with your own forces, for this you will need a circular saw. With it, you can shorten the doors without even removing them from the loops. First of all, you need to make accurate measurements so as not to cut off too much, then calm down so that the hand does not flinch, and start acting. Remember that the gap between the floor and the door should be more than five millimeters. In this case, the door will look like “glowed” and extraneous intervention none of the relatives and acquaintances will see. Door shortening can also be done using a hand cutter. In this case, the door will have to be removed from the loops. Then it will need to be put on a flat surface and thoroughly fixed with clamps, pressing them on top of a wooden block, which must be exposed to smoothly. He will serve as a guide for the milling. It must be installed, so that the milling cutter removes the wood at just such a distance as planned. no more, no less.

As you already understood, you will have to suffer with a milling. And this process will take more time than the first door cutting option. You will have to make several approaches, while gradually deepening into the canvas. But do not forget that this method is more reliable and it will be easier for you to avoid irreparable errors. Experiment, try to achieve everything yourself, but do not forget that your actions should be carried out within a reasonable.

Each person, buying a door, hopes that it will not have to be repaired for a very long time. For this, many people order doors from professionals to be confident in their quality. But there is nothing eternal in life, and repairs in the apartment are an inevitable action. After you install linoleum or laminate on the floor, the interior door, by definition, will begin to close poorly and open, since the height of the floor has increased. Therefore, you will need to cut the door so that it opens freely, and does not creak. If you leave the solution to this problem for later, you can simply ruin the door. And do not forget that buying a new model will be expensive, because no one has extra money now.

where/how to cut the door leaf carefully?

You will have to make several approaches, while gradually deepening into the canvas. But do not forget that this method is more reliable and it will be easier for you to avoid irreparable errors. Experiment, try to achieve everything yourself, but do not forget that your actions should be carried out within a reasonable.

Few of the masters know exactly how to shorten the door, since this requires certain skills, and, of course, experience. After all, damaging the door is a minute business, and fixing is a complex and tedious process. Of course, the most ideal option is to turn to professionals who have the necessary knowledge and tools for this “operation”. Today you can get confused in the variety of companies that offer these services, and even more so to understand which of them is the best and profitable option for you. But you should not despair, you just need to know a few rules:

Do not contact a company that recently announced itself, and in the information writes that there has been existing in the market for decades. In this case, shortening of interior doors may end with the purchase of new.
If you decide to save, do not order private companies, it is better to use state proposals for repair. So you will save a certain amount of money, and you will rejoice at the result.
In order to find an inexpensive company, first you need to compare for the offered services. After that, you can safely order masters.
As soon as the master crossed the threshold of your home, once again check the price of his services. If they are higher, you can immediately call his company, and clarify the terms of the transaction again.

TOP-4 ways to reduce the interior door

Reducing the door and its opening is a difficult matter, but with the help of the correct tool and accessible instructions, the whole process can be carried out independently. The main thing is not to be afraid of upcoming difficulties and tune in to the creative process.

Is it possible to reduce the interior door?

The interior door consists of a box and a canvas. The box is tightly attached to the wall, and the canvas opens and closes the passage. You can reduce any door and any opening. It is important to correctly measure and prepare the necessary tool.

Reduce the size of the door in cases where it is installed in the joint with the wall or blocks the large area of the room. Large heavy doors sag over time. In some cases, the dimensions of the opening are reduced due to large heat loss. It will also come to work with the dimensions of the canvas, if the floor level rises, or the sediment of a wooden house occurred and the door was clamped.

Differences in working with different doors

There are quite a few types of doors: from light plastic to heavy steel. Aluminum or iron doors are rarely placed in the interior space, and the rest of the types are easily processed with a manual tool.

Sprinkle with the aim of narrowing or making almost any wood door, wood.fiber plate or canvases covered with veneer. With the exception of glass. You can, of course, cut off an extra piece from a glass fabric, but it is usually made of fecal, thick glass. For this type of work you will need a special machine.

If the door is combined, for example, glass elements are inserted into the wooden frame, then such a door can be narrowed or shortened to the thickness of a wooden frame without touching the glass.

Laminated, veneered, cushioned doors are very easily sawn, because this is a tree processed in a special way. The same applies to plastic.

Reduction in height

If the doorway is too high and it needs to be reduced, then this is done in its upper part. There is the smallest load, therefore, a light and affordable material is selected for work. plywood or drywall.

Materials and tools

First of all, you need to decide on the material. It is easy to work with drywall, cut it and adjust it to the desired size, but it is fragile and easily breaks with a slight load. Plywood in this regard is much stronger, but more expensive.

The tool that will be needed to reduce the height of the opening is available in any construction store:

Operating procedure

The opening for any type of doors is reduced in the following way:

First of all, it is noted at what height should be the upper edge of the door.
Then, a metal profile is attached to the wall for the installation of drywall to the wall. It can be replaced with a wooden beam with a cross section of 5 × 5 cm, so the design will be stronger and it will be possible to install not only drywall on it in the future, but also the plywood. The lower beam is attached only after it has been exposed with the help of a hydraulicarian.
After fixing the supporting frame above the door, with screws are attached to it, a piece of plywood or drywall cut in advance in advance. After installing a plywood or drywall shield on the frame, the gap between it and the wall is covered with putty. So that it does not crack over time, a reinforcing tape is first glued to the gap.
Then the door leaf is adjusted to the desired height. Having measured the exact distance from the lower edge of the doorway to the upper edge with a tape measure, you need to postpone the same distance on the canvas. So that the door is easily closed, this distance decreases by 2-4 mm.
With the help of a conventional or electric jigsaw, an excess part is cut off from the canvas. At the same time, it does not matter what material the door is covered. the jigsaw easily cut the veneer or laminate of any thickness.
The cut out the edge on the door rummages and paints.

You can lower the door with a wooden beam. This method is often used in houses with wooden walls. In this case, the beam is sawn off the width of the doorway and attached to the desired height. If its thickness is not enough to reach a given height, another one is added, etc. D. The last beam for accurate fitting is processed with a shirt or sawn off with a hacksaw.

Width reduction

The main problem of reducing the doorway in width is to preserve the strength of the structure. Even if the door is not fixed from the side of the installation work, the load on the opening will be distributed evenly. That is why the frame for the structure should be very reliable, it is better to use foam blocks or bricks for this.

The tool in this case is selected depending on which material for narrowing the opening will be used. If it is drywall, then you will need a jigsaw, ruler, level, screwdriver. If a brick or foam block, then you need a trowel and a container for a concrete solution. As for the order of work, it also depends on the selected material.

Using drywall

The algorithm of actions when using drywall is as follows:

The first point is the application of marks to the existing opening.
Further around the perimeter, the marked area, a beam or metal profile is attached.
To enhance the structure, you need to make at least two horizontal crossbars at the same distance.
A pre.dried.up piece of drywall is attached to the frame with screws.
A layer of basalt wool or other soundproofing material is laid between the panels of the drywall.
In conclusion, the gaps between drywall and the wall are sealed with a mounting ribbon and put down.

With the help of a bar

The beam is used in wooden houses. This is structurally more convenient and harmonious from the point of view of aesthetics. First you need to adjust the beam to the desired parameters.

Showing the door. tips

In the course of work in a particular area, any master with time has his own invaluable experience. I am also not an exception, over the years I have accumulated some knowledge, additional skills, if you like, tricks in my craft.

It can come in handy. Picture-Link to determine the direction of movement of the door leaf.

Many people ask: “Where it is better to open the doors to the corridor or to the room?””

According to the rules of construction. from a smaller room to more, but in general it is necessary to put it so that, first of all, it is convenient for residents. To determine the direction of movement of door slotted loops, see the photo. On which side the slot between the halves (cards) of the canopy in a closed position is left or right, then this is the canopy. There are still insoluble awnings, but they are universal and therefore they can be rotated. So everything is simple.

I tried to trim the door to the door in width, t.e. made from seventy (700 mm) sixties (600 mm) in a new way. I liked it because it is fast and good. To quickly reduce the door leaf, I use this is not a complicated device made using a conventional angular grinding machine (corner grinder) and a detachment of wood with a diameter of 125 mm no more.to. Sawed should be half less than the thickness of the door, because when the saw exits its teeth, the edge of the laminated wood.fiber slab is torn and it turns out not a clean and not beautiful cut. In order to still saw off, you just need to do a drink on both sides. Watch the video and photo below.

In the video and in the photo you can clearly see the process of cutting the door leaf in width.

If you did not understand something, then you can contact me in the “Contacts” section. I will answer any of your questions.

Pruning of interior veneered doors

Before starting work on trimming, the canvas is removed from the loops. All the elements of accessories like loops, handles and locks are removed from it. After that, the door:

Fixed using clamps or in any other available way. The main thing is the immobility and reliable fastening of the canvas.
Marking is applied. For these purposes, a square and a ruler are used. If the veneer is located on the door on both sides, then the cutting mark is also made on both sides and on the ends.
The guides are attached. The iron guide is fixed on the canvas using painting tape.
Shit of veneer. Small deep cuts along the guides are made with a sharp knife. If the door is completely veneered, such incisions are made from all sides.
Removing veneer. At this stage, pay attention to the varnish (if any). If it cracks, then before removing the veneer layer you will have to remove the coating with sandpaper.
Removing the unnecessary part of the door leaf with a shirt, saw or milling.
Cutting processing. If necessary, the cut place must be treated with sandpaper.
Preparation for gluing. The cut place is degreased with alcohol.
Bleing veneer/furniture tape. The cut is covered with PVA glue, after which a veneer or furniture tape is attached to it.
The final stage. Excess glue is removed, if necessary, the surface is covered with varnish.

It is worth stopping and examining in detail the question of what is better to use when rubbing the unnecessary part of the canvas.

Removing part of the door leaf: shirts, milling cutter, saw

A classic tool in order to cut off an veneered interior door. a rubbish. You can use both ordinary and electric tools. It provides gradual removal, simple in circulation. We include the disadvantages of the possible irregularities of the surface and inconvenience when used in large areas. Special requirements for rubbines are not advanced.

Circular saw for an acceptable result requires experience working with it. For trimming the interior door, a saw disk with carbide teeth is required. For a clean cut, it is recommended to choose a disk with as many teeth as possible. The advantage of this tool is that even a large area can be processed in a short time. Disadvantage: work on trimming veneered interior doors should be carried out extremely neatly and slowly, otherwise the veneer may be knocked out.

Work by a milling mill

A manual milling cutter is the most preferred option, since it allows you to accurately remove the layers of the canvas, it is easier to control it compared to a saw or even a shirt. Of course, it is not necessary to buy such a specifically tool. it can be rented or lend from friends. Under the saw, the milling cutter gradually approaches the guide, which allows you to carefully and carefully get rid of the unnecessary part of the door leaf. This tool leaves fewer chips or hooks than the rest. With a crucial approach to the case after the completion of the process of shortening the door, processing with sandpaper may not be needed.

Instructions for independent work

Before carrying out the work, remove the canvas from the loops and prepare, removing the pens and other accessories from it. The door is cut on a workbench, but in the absence of its absence, a large stable table is suitable.

If the canvas from the array must be adjusted to the opening due to sagging or lifting the floor, then it is best to do the door trim from below. Remove 2 standards of height: on the loop and in the narthex. Merki transfer to the canvas, putting down new dimensions from the upper edge. Through 2 points draw a straight line for a trimmer. To do this, it is advisable to use a long ruler and a square to control the right angles between the edges.

Attach the guide rail by the applied markup. When using a power tool, it is better to use a metal strip or ruler. If you cut the door with a hand hacksaw on wood, guides from even racks are suitable. Press the template to the canvas with clamps above the marking.

To save a layer of varnish and veneer on a polished door, treat it with a corner grinder. The disk of the tool will leave the cut with even edges, which cannot be made with a saw. Take a corner grinder along the guide bar. Before processing on the mowing fishing line, glue the tape, and transfer the straight line to its surface.

If there is no corner grinder, the varnish coating on the removed part is removed with an sandpaper, and the veneer is cut out with a sharp knife on both planes of the canvas and on its only parts. After that, the door can be sawn down along the guide.

Remove the clamps, process the cuts of the cut with sandpaper. You need to glue the brown tape on the veneered door, choosing its shade to the veneer. If the massive canvas is painted, cover the cut with paint or varnish. Hang the door leaf on the frame, eliminate distortions and attach the removed accessories.

How to Trim a Door in 10 Minutes

In the same sequence, work is performed when replacing the canvas: the standard dimensions of the new product can be changed in height and width. When performing work, you need to consider what the product is assembled from.

Tips for professionals

A canvas from an array or wood.fiber plate can be trimmed from below if it does not have a philanic or their imitation. In the presence of a symmetric decor, it is better to cut off on both sides, dividing the value of the cut part by 2. These measurements are laid from each edge, without violating the symmetry of verity and the lower philanthone. The same is done if you need to reduce the standard width of the door leaf.

Frame hollow doors cannot be shortened too much. The product consists of wooden bars having a limited thickness. When performing work, you need to leave at least 1-1.5 cm of the frame bar inside the canvas. You can shorten the door, as indicated for design with phylenes. from above and below.

Read checking the battery of an electrical screwdriver multimeter video

When you try to install a standard door in a small opening, the chasing materials of the frame are shortened by the standards and fixed in the opening. The sizes of the sash will have to be adjusted according to the technology described above.

The canvas from the array sometimes swells due to excess humidity and does not enter the frame well. You can eliminate such a problem with a shirt or grinder (manual milling). Remove the canvas, put on a workbench and process its edge with a cutting tool, removing several millimeters of the chips from the right side. Hang the door and try its move. If the problem is not fixed, repeat the processing.

To get an even section of the array when using a circular saw, a disc with a large number of small teeth will be required. But even under this condition, it will not be possible to cut out the veneered product qualitatively. For a canvas made of wood.fiber plate, it is better to prefer an electrician, and perform the work in compliance with the layer of veneer of the rules (gluing tape, cutting veneer).

If it is possible to use a hand cutter, then you only have to choose it for work. The tool will perform even and clear sawing, and the cutting line for the cutting trimmer will not have to be processed additionally on a massive product, or on a wood.fiber plate or a frame model.

For proper gluing the bromic tape, use PVA glue and iron. The adhesive layer needs to be applied to the saws of the canvases, let it dry. Apply the tape to the edge of the door and iron through the paper with a hot iron. After cooling the excess, cut the tape with a sharp knife, and slightly wipe the edges with sandpaper.

Are all wooden doors suitable for trimming

This issue is no less relevant than the work technology. All materials based on a tree can be cut. over, this must be done if the opening is difficult to open, and for this it is necessary to make efforts. Among the most used woody rocks are distinguished:

Natural material serves the owners perfectly and is easily cut using the aforementioned technologies.

White or black circles on the surface of a wooden table. this is not a reason to throw furniture, thinking that nothing can be fixed. Any pollution can be removed by materials that are available in any house.

Used as an auxiliary solution for the transition between the floors of residential and non-residential buildings, the Mr.-shaped staircase with the site allows us to significantly simplify the rise process, without making it too long or cool for.

A teenager’s room. A special place where Chaos prevails over the order, and the place is still not enough to store all the necessary little things. Accordingly, the furniture here requires a completely special, having characteristic.

In search of an answer to the question: from which tree to buy furniture, you came to a standstill? Learn about different breeds of natural wood and the rules for choosing suitable materials. Choosing furniture made of wood, from.

Sometimes there comes a moment when you need to enter a rented apartment or make sure that you only have the keys to the room, and there is no much desire to change the entire castle. In order not to mess around.

Alteration of interior doors

In the latter case, it will be more correct to correct the error. Before installing the doors on the hinges, make sure that the dimensions of the canvas are shorter than the gap of the box by about 10 millimeters, and it is already 4-5mm, and the lines of the canvas and the bouts are parallel. At the same time, you can make sure that the vertical stand of the box from the side of the loops is perfectly even. this is very important.

Sometimes a question arises. How to shorten the door after a laminate or parquet that was unexpressed earlier. The network is full of descriptions, how dashing installers are controlled with this operation using a end circular saw. We recommend that you do not follow such tips. If you can allow such an operation in relation to the door from the wood.fiber plate, then the veneer of valuable woods will most likely be spoiled. The difficulty is that even the smallest teeth of the saw will tear out particles of veneer, forming chips and creases, it is no longer possible to fix such a marriage.

However, carefully cut the doors in height is quite possible. In Runet, this is advised to do this using a powerful manual electrophoresis and the guide line. The method is real, only dust is in a pretty dust, and a figured overhead decor does not always allow you to reliably fix the ruler. It is easier to do this operation using an electric rhubank, professional installation of doors without this tool does not do. In particular, a competent carpenter with the help of an electric rhuban forms on the vertical part of the canvas facing the hinges, a corner slightly different from 90 ° and open towards the narthex. As a result, the loops in a closed state are also slightly ajar, which removes all the stresses between the box and the canvas.

How to correct the interior door

Each person, buying a door, hopes that it will not have to be repaired for a very long time. For this, many people order doors from professionals to be confident in their quality. But there is nothing eternal in life, and repairs in the apartment are an inevitable action. After you install linoleum or laminate on the floor, the interior door, by definition, will begin to close poorly and open, since the height of the floor has increased. Therefore, you will need to cut the door so that it opens freely, and does not creak. If you leave the solution to this problem for later, you can simply ruin the door. And do not forget that buying a new model will be expensive, because no one has extra money now.

Gluing veneer to the processed door

Despite the fact that the procedure is simple, some skills should be mastered. Glue the veneer to the processed door is possible in several ways.

Cold contact method

It is considered the most difficult way of gluing wood with a treated surface. Implies the use of contact glue. The difficulty lies in the fact that the binding composition quickly sets. Because of this, it will be extremely difficult to correct inaccuracies with the improper placement of contacting surfaces.

To make the gluing reliable, it is required to create a strong clamping force in the first seconds of the contact of materials (press with your hand or cargo). Experts do not recommend using large planes for gluing.

Hot gluing

A layer of glue is applied to the glued planes, which should dry a certain period of time. After that, it is necessary to attach a leaf of veneer exactly in size. With the help of an iron, the sheet begins to be smoothed from the center to the edges. The glue composition under the influence of high temperature melts and glues two materials. In order for the contact method of hot gluing to work, it is necessary to use the adhesive composition of a thick consistency. So that the glue does not dry too quickly when using the iron, you need to moisten the veneered surface with warm water. At the places of bloating, it is necessary to make punctures or incisions to release air.

Cold gluing with pressing

A classic method of gluing, which requires fixing clamps on glued surfaces. The core is indicated on the packaging of the composition used. After drying, it is necessary to remove the clamps and check the condition of the door of the door.

Useful tips and recommendations

When using veneers from expensive wood (oak, ash), it is necessary to apply a layer of cotton fabric on the canvas.
Grinding a new surface can only be on fibers with sandpaper.
Since the new coating absorbs water well, immediately after gluing it must be covered with a layer of varnish.
Using an iron, you need to constantly drive them on the work surface. It is forbidden to delay the preheated metal surface in one place. In case of plowing, it is necessary to remove the blackness with a sharp knife or blade.
To fix the long veneer strip on the edge, you need to fix one of the edges with an iron or a construction hair dryer. It is convenient to fix the edges and corners with a soldering iron.
The coating of radius doors needs to be entrusted to the faces of old furniture.
The coasted panels of veneer from different woods look unusual.
On the ends located from the bottom and top of the canvas, it is required to cut 2 mm of the chamfers on both sides. The sash will not cling to the box after gluing a new wooden coating.
When cutting a sheet with a knife, it is recommended to do this across the fibers. If the sheet is cut along, it is necessary to make several movements with a blade. Otherwise, the cutting part of the knife will slip and ruin the sheet.

Performing elementary rules, you can do work without difficulty.

Work technology:

To reduce the width or height of the door leaf to 0.5 cm

Fugging machine. Gives the best result, but not everyone has such a machine;
Electrofugan. It gives a good result, but also in the household it occurs infrequently;
Electric russian. It gives a good result, but you need to work carefully, because in the end, if you do not hold the rubble, it often chooses an unnecessary recess;
Ordinary shirt or jackets. If the height of the door is reduced, then the table bars need to be shortened with circular, hacksaw or electric.

After cutting the ends of the door are treated with grinding. From the canvas made of wood.fiber plate in the places of cutting, it is advisable to remove the chamfer (beat the ends a little). It is better to do it manually, a grinder mounted on an iron or a plastic grater.

To reduce the width or height of the door leaf by 0.5-1 cm

Circular machine. Gives the best result, but again, not everyone has such a machine;
Manual circular saw. It gives a good result, but also in the household it occurs infrequently;
Electric. Almost never it turns out to be even and therefore the canvas must be additionally strict, so you need to cut with a small margin;
Manual saw (hacksaw). The incision turns out to be more even even, but often not perpendicular planes of the canvas and therefore the canvas must be additionally strict, so you need to saw with a small margin.

Note: when reducing the door width, cut the door, preferably on the side where the lock will crash, and not on the side where the canopies will be placed.

3a. To reduce the width or height of the door leaf by 1-3 cm

It will take preliminary disassembly of the door and glue to enhance the design of the door. The success of disassembly depends on the quality of glue. Try to separate the wood.fiber plate with a wide chisel in the place of future cuts from the wooden bar of the frame. If the canvas is separated quite easily and does not destroy at the same time, carefully free the bar of the frame, pull out the metal brackets with the fastening frame and carefully cut the canvases with the wood.fiber stake on the wood. After that, you need to reduce the width of the upper and lower bars of the frame (if you reduce the width of the door), and remove excess honeycombs (with a wallpaper knife or just with your hands) to insert the bar of the frame. The bar can be screwed or shot with brackets. After that, the canvases are glued to the bar, for this you can use PVA glue and the usual painting tape if there is no press.

3b. To reduce the width or height of the door leaf by 1-3 cm

additional wooden bars and glue are required to enhance the design of the door. If the wood.fiber plate of the canvas could not be separated, then you will have to cut it on the frame (the tools are the same), then knock out what remains of the bar, remove excess honeycombs to insert a new bar of the frame. It is advisable to fasten the bar. After that, the canvases are glued to a new bar, for this you can use PVA glue and ordinary masking tape if there is no press.

You need to cut the door only in the goggles and not in a hurry, since the probability of the cutting part of the tool on the metal brackets that fasten the frame is high.
If the door is phylene, then it is advisable to cut in width on both sides to preserve the symmetry of the pattern.

After the glue dries, the ends of the door, if necessary, are strict and treated with grinding. From the canvas made of wood.fiber plate in the places of cutting, it is advisable to remove the chamfer (beat the ends a little). It is better to do it manually, a grinder mounted on an iron or a plastic grater.

To reduce the height of the door leaf by 3-5 cm

glue will be required to strengthen the design of the door. Cut the excess part of any of the methods described in p. 2. Using a wide chisel, spit the remains of the wood.fiber plate of the canvas from the wooden bar, remove the excess honeycomb (with a wallpaper knife or just with your hands) to insert the bar of the frame. After that, the canvases are glued to the bar, for this you can use PVA glue and the usual painting tape if there is no press.

After the glue dries, the ends of the door, if necessary, are strict and treated with grinding. From the canvas made of wood.fiber plate in the places of cutting, it is advisable to remove the chamfer (beat the ends a little). It is better to do it manually, a grinder mounted on an iron or a plastic grater.

How to reduce the height and width of the doorway, which materials to use for work

The need to reduce the opening often occurs when redevelopment. In addition, during the construction of the facility there may be errors. As a result, to install the door frame, you need to adjust the dimensions of the opening to the required dimensions. In order to reduce the height and width, different materials are used. They are selected, relying on the type of structure: the supporting wall or partition. In addition, the choice of material should be done, given the configuration of the doorway. For example, it is better to use drywall to install arched structures.

Why reduce the opening?

Changing dimensions may be required in some cases:

when redevelopment, if during the repair it was decided to install narrower doors;
to increase the free area of the walls, if you need to arrange additional furniture, and the doorway is wide enough; often, such a need arises in the living room, the hall, for comparison, the entrance to the bath and the toilet is initially characterized by a small width;
Correction of the errors that were allowed during the construction of the facility;
It is required to reduce the doorway in order to change its configuration, for example, if you need to make an arch from a rectangular structure.

Preparation for work

Measurements can be made after dismantling the door leaf, mounting elements and decor. Thanks to this, it becomes possible to avoid inaccuracies in the calculations. First remove interior doors from loops. This may require the dismantling of self.tapping screws if the loops are universal, sterful. Dismantle platbands, finish nails and other fasteners. At the last stage, they remove the box. To do this, remove the mounting foam, which fills leaks between the wall and the design.

In addition, you need to choose the material. Of the most preferred options, wood, GKL and brick sheets are distinguished. At the next stage, the volume of material for work is calculated. In this case, the wall thickness, the height and width of the prepared opening are taken into account. If the entrance is wide and it must be narrowed by 1/2 or 1/3, it is better to use more durable materials.

When they plan to reduce the doorway, you need to prepare tools:

a rule of significant length;
building level;
roulette;
marker;
electric screwdriver;
cutter;
A sharply sharpened knife.

The work will use auxiliary materials, in addition to the main one: plaster, primer. The choice is made taking into account the properties of the supporting structure. So, for a concrete wall and a wooden wall, different finishing materials are prepared.

How to narrow the doorway?

There are several ways to reduce the entrance to the room, but all of them are performed after marking. It is necessary to transfer to the wall surface a sketch pre.made on paper. To do this, use the aluminum rule, the building level and the marker. The marking is transferred to the wall in the direction from the bottom. This is a more convenient way.

By width

If you need to reduce the entrance to the room, the rule is set on the floor close to the opening. This tool should have a significant length, then it will be possible to ensure the emphasis on the walls. With the help of a marker, draw a fishing line for a trimmer on the floor. It will correspond to the departure of the wall that needs to be increased. For example, if for narrowing it is necessary to reduce the size of the opening by 10 cm, a segment of this length is transferred to the floor. The reference point is the edge of the wall.

To make the design even, you should draw the same fishing line for the trimmer and in the upper part of the opening. Do this “by eye” is not worth. It is necessary to draw a basic vertical on the wall, from which the segment will be posted in the upper part of the entrance. Its length should correspond to the similar parameter of the line on the floor. To apply the basic vertical on the wall, it is recommended to use the building level and plumb. The installation of the selected material is carried out along the marking lines: brickwork, mounting sheets of GKL or wooden beam.

In height

Large doorways are reduced using a frame made of metal profiles. This method is suitable if it is planned to make significant changes to the design. For cases when the height decreases by 10 cm or less, you should choose drywall. With its help and even without a metal frame, you can lower the upper bar of the opening. Installation should be carried out through adhesive, primer.

For the duration of the work, part of the flooring must be protected with a film so as not to stain it with glue. Installation can begin after a decrease in the width of the opening. Cut drywall. Its width should correspond to the thickness of the wall. The blanks are treated with a primer and left to dry in a horizontal position so that the sheets do not deform. Then, with the help of glue, they are attached to the upper slope. He is also pre.primed and dried. Glue drywall into several layers until the desired level of height heights is reached.

With which it can be done?

There are many options for reducing the entrance to the room: wood, brick, aerated concrete, special glue, drywall. Methods and tools are selected taking into account the length of the departure of the wall that needs to be increased. To build large.sized structures, it is better to choose more durable materials: aerated concrete, brick.

Is it possible to cut the interior door? Preparation and methods of fitting canvas

During the repair in the house or apartment, the floor level often changes, and this immediately responds to the interior doors. They open hard or do not at all in a decreased opening. And if it is decided to redevelop and I want to do the opening already? In general, the problems can be different, but the essence is one. the interior door needs to be cut.

Is it possible to cut the interior door?

There are several designs of interior doors, and each needs its own approach. Quite often a lightweight canvas is installed. It consists of a frame (frame) and filling, and a wood.fiber slab or other material is faced from above. In case of damage to the supporting frame, the strength of the structure decreases, and it can be deformed. It is not recommended to cut such a canvas from any side. If necessary, you can cut it only slightly. no more than 1 cm. If the door is monolithic and collected from hard plates, then almost any cut is allowed from all sides.

Another problem. Doors can be shy (smooth), completely recessed in the doorway, or with an overlap. In the latter case, an edge is formed on the edges of the canvas, which does not enter the opening, but closes the gaps between the door and the wall or the floor. Smooth doors are quite pruning, but in the second version it all depends on the width of the edge.

Finally, decorated doors can have a certain pattern. Pruning can change symmetry, worsening the appearance. This factor should be taken into account when planning work.

Preparation of materials and tools

To change the size of the door leaf, the following tool is required:

Cutting tool. Depending on the material of the door and the degree of shortening are used: a hacksaw, a hacksaw for metal (suitable for plastic), corner grinding, a rubbish, a milling mill, a circular saw, an electrician.
Clamp. It is necessary to fix the canvas during operation.
Hand tool for refinement: carpentry knife, chisel, files, hammer, screwdriver, Kerner.
Sandpaper for finishing processing.
Measuring tool: roulette, metal ruler, square.

Depending on the design of the door and the coating, consumables should be prepared in advance:

Glue. PVA, carpentry, epoxy, special glue D2 for wood, “moment” or other varieties.
Wooden bars and rails of different sizes.
Maslar tape and metal guides for the direction of cutting tools.

Preparation of the canvas for work

Before starting direct cutting, the following preparatory work must be carried out:

Remove the canvas from the loops and free it from accessories (handles, loops, other protruding elements).
Place the canvas on a workbench or even platform (table), fixing with clamps. It is necessary to ensure complete immobility.
The doorway and canvas are thoroughly measured in order to determine the optimal cutting place and the degree of shortening. Marking.
Preparing a place to work cutting tools. When working with a disk (circular) saw from below, a board is fixed under the cut. If an angular grinder is used, it is recommended to ensure emphasis on both sides of the cutting line.
In the presence of veneer, it is carefully cut through the guides with a knife. If there is varnish coatings, then to exclude its cracking along the cutting line, the varnish is removed by sandpaper.

Full preparation of the canvas will facilitate the cutting process and improve the quality.

How the cut value affects?

Cutting technology and the cutting tool used depend on the size of the cut strip.

To shorten the canvas by 0.5 or less, the professionals use a fugging machine or electric fugus, but at home they are rarely available. You can use a regular rubbish (fugan). With a decrease in height, an electric jigsaw or hacksaw with small teeth is more often used. In the end, the end is polished
With the size of the cut within 0.5–1 cm, manual circular saw is used. When cutting with an electrolobian or hacksaw cut, it turns out uneven, which requires subsequent strict. This circumstance should be taken into account when cutting, taking a supply for strict.
Reducing the size of a hollow (frame) canvas by 1-3 cm requires preliminary reinforcement of the structure. You will have to partially disassemble the canvas at the pruning site, and install the enhancing bars, fixing it with glue or brackets. Cutting itself can be carried out by the same tools as in the previous case.
When cutting the frame bar with 3-5 or more cm, it is necessary to strengthen the frame. The width of the rack is restored using an additional beam, which is firmly fastened to the remnants of the previous structure and is associated with perpendicular elements. The new design is carefully enhanced by glue. An extra strip of wood.fiber plate is sawn off with a hacksaw or an electrician. At the ends of the wood.fiber slab, a chamfer is cut off. The place of cutting the canvas is polished.

Door trimming in height

Most often, doors shorten in height. For this, first of all, it is necessary to determine which side it is better to do. from below or from above. The decision is made after careful measurements and taking into account the location of the loops, which is undesirable to rearrange.

From below

If the need to change the size of the canvas is caused by an increase in the level of the flooring, then the best option is to trim the door from below. It is carried out in the following order:

The cutting of the cut is made using a metal ruler and a square. Dimensions are tied to loops. Draw a straight line for a trimmer cut.
Slightly above the drawn line, guides are installed. They are attached with clamps or painting tape. For power tools, metal skids are needed, and wooden rails are also suitable for a hand tool.
With the help of the desired cutting tool, a strip of the door leaf is cut off along the marked line.
If the edge of the cut is bumped, then strict is carried out using a rubbish.
Directors are removed, and the spinal place is treated with sandpaper.

How the cut value affects?

Cutting technology and the cutting tool used depend on the size of the cut strip.

To shorten the canvas by 0.5 or less, the professionals use a fugging machine or electric fugus, but at home they are rarely available. You can use a regular rubbish (fugan). With a decrease in height, an electric jigsaw or hacksaw with small teeth is more often used. In the end, the end is polished
With the size of the cut within 0.5–1 cm, manual circular saw is used. When cutting with an electrolobian or hacksaw cut, it turns out uneven, which requires subsequent strict. This circumstance should be taken into account when cutting, taking a supply for strict.
Reducing the size of a hollow (frame) canvas by 1-3 cm requires preliminary reinforcement of the structure. You will have to partially disassemble the canvas at the pruning site, and install the enhancing bars, fixing it with glue or brackets. Cutting itself can be carried out by the same tools as in the previous case.
When cutting the frame bar with 3-5 or more cm, it is necessary to strengthen the frame. The width of the rack is restored using an additional beam, which is firmly fastened to the remnants of the previous structure and is associated with perpendicular elements. The new design is carefully enhanced by glue. An extra strip of wood.fiber plate is sawn off with a hacksaw or an electrician. At the ends of the wood.fiber slab, a chamfer is cut off. The place of cutting the canvas is polished.

How to do work?

Short the height

In houses with an old layout, a narrow passage is usually observed in height. Modern doors in such houses do not look at all. Changing sizes greatly affects the appearance of the apartment.

The Secret to Trimming Down a Hollow-Core Door. Today’s Homeowner with Danny Lipford

In height, the opening is reduced in three ways:

Using a wooden beam.
Is tapped with a hammer until the edges become perfect in level. The level should be constantly verified in directions.

Everything should be correctly completed, since the result depends on the measurements.

The profile is measured so that it can be cut into the desired length and fixed tightly with self.tapping screws.

height

Narrow the width

You can narrow the doorway by starting with the marking of the segments. This is performed by an aluminum rule:

It is placed on the floor and with a pencil or marker drawing lines of the necessary sections.
On the perimeter of the lines, we put the guides on the floor, the upper slope.
We fix our design.
We insert rack profiles.

The walls should be well soil before each installation stage. The priming is carried out abundantly, several times. This measure will provide good contact of the application material with the surface.

You can cut the necessary plasterboard sheets in size. Most often, the builders use special glue. If it was not at hand, then the usual gypsum plaster will help out.

The entrance door can be reduced if all the necessary tools are at hand. It is necessary to carry out appropriate measurements, calculate all parameters.

Sources:

https://lu-va.ru/kakie-mezhkomnatnye-dveri-mozhno-podrezat-po-vysote-kak-pravilno-podrezat.html
https://stroitelstvo-gid.ru/dveri/kak-obrezat-dver-po-shirine.html
https://mezhdveri.ru/8286-kak-obrezayut-mezhkomnatnyie-dveri.html
https://aqua45.ru/dver/podrezat.html
https://dtm-spb.ru/stati/kak-obrezat-mezhkomnatnuyu-dver/
https://lu-va.ru/kak-otpilit-laminirovannuyu-dver-kak-podrezat-mezhkomnatnuyu-dver-podrezat.html
https://xn80alqibft0g1a.xnp1ai/svoimi-rukami/kak-podrezat-dver-snizu.html
https://stroitelstvo-gid.ru/dveri/kak-ukorotit-dver-mezhkomnatnuyu-po-vysote.html
https://pilka-nn.ru/pro-dveri/kak-ukorotit-dvernoe-polotno.html

Articles door, height, interior