Cleaning Air filter of a trimmer for Huter grass. Why is a chainsaw is under load

Cleaning the air filter for a trimmer for the grass Husqvarna 128r

Useful material from which you will learn how to get a capricious gasoline trimmer for grass that does not want to work!

The summer time has come, and in the personal plots habitually hidden the lawn mower. Great tool, powerful and mobile. Using a gasoline trimmer for grass and grass, you can mow, and get rid of a dried.up weed. However, there are cases that the lawn mower does not start, works with interruptions or without developing full power. Of course, no one is at work! And as they say, you twitch the laborer’s handle more than the mowing.

Difficulties with the launch do not only have the types of motorcycle, but also in new. How to be in this situation? There is only one way out. to listen to the advice of experts and take advantage of their practical experience!

If you put a cable instead of a fishing line, without the possibility of its release, reliably fixing the two ends of the cable and cutting them with welding (a drop of melted metal holds the cable from blooming). Grass such a tool “falls” at a time. The shoot is cut off about a finger with a thickness. Stones are not as afraid as disk. There is true, the problem: when wear, pieces of cable threads break off, and these twisted wires remain in the place of mowing. If you step on them, you can get hurt.

But pieces of the cable remaining on the field are half a bastard. The fishing line for the trimmer, breaking off, weakens the dynamic blows to the transmission and the engine, the cable does not give such an opportunity. Result of quick wear of motorcycles.

Also, the ignition coil can be broken in electrical equipment. In this case, the lawn mower will not start or start and works with interruptions, and then stalls, or “hot” does not start at all.

You can check the serviceability of the coil in the same way as when checking the spark: we unscrew the candle, lean it against the trimmer body for the grass. If there is no spark with a jerk of the starter, or it appears through time. you need to change the coil.

Review of models

Gasoline braids for grass are widely used for professional laws care, as well as in agriculture. These samples of modern technology have proven their effectiveness when leaning weeds and hay harvesting

In such conditions, special attention is paid to the correct choice of the representative of the model range, taking into account the design characteristics and technical characteristics

At the moment, potential customers are offered the following models of the STIHL motorcycle:

To describe the main features of representatives of these categories, it is worth considering some samples of technology. So, the light lawn mower FS-38 is designed to perform simple landscape work, as a rule, in the conditions of personal plots. The weight of this tool is a little more than 4 kg. In this case, the operating volume of the engine and its power are 27.2 cm3 and 0.65 kW, respectively.

The main advantages of representatives of this category include the following operational indicators:

• insignificant weight;
• maximum ease of use;
• minimum fuel consumption;
• power plant power;
• reliability and long service life;
• minimum noise and vibration;
• modern design.

One of the popular models related to the segment of powerful trimmers is Stihl FS-13. The “heart” of this six.kilogram braid for the grass was an engine with a volume of 36.3 cubic centimeters and a power of 1.4 kW. The model is equipped with a tank with a volume of up to 0.5 liters. Powerful lawn mowers, as a rule, are classified as professional tools with the following advantages:

• increased power;
• maximum reliability and durability;
• the possibility of processing almost any surfaces, including thick shrubs;
• convenience and ease of operation;
• the presence of a “bicycle” holder handle.

Instructions for Huter GGT-1500T

one. Introduction ………………………………………………………………………… 3 2. Safety regulations……………………………………………………. 3 3. Technical characteristics …………………………………………………… 4 4. Assembly………………………………………………………………………………… 5 5. Operating instructions ………………………………………………………………………………….………… 8 6. Running

Do not remove the lid of the fuel tank when the engine is running. If the fuel spills when filling the tank, be sure to wipe the fuel spots with a dry cloth and change the place before starting the engine. ten. Do not use the fuel mixture to clean the trimmer for grass. eleven. Any maintenance and replacement measures

Assembly of a trimmer for grass 1 2 2 3 4 5 6 7 8 9 10 11 12 handle Starter Starter Starter control lever cap of a high.voltage wire lid Fuel tank lid Leville handle Handbone Corps Fuel tank right handle control hilt of the handle mount

one.Barbell.(for the GGT-1500S model) squeeze the fixing lever of the mounting system, and combine both parts of the bar. Fastening the fixing lever should enter the guide groove on the lower rod. The correctly assembled connection cannot be opened without pressing the fixing lever. Tighten the additional

Install a cutting knife on the hub. Make sure that the cutting knife is correctly specified and lies on the hub groove. Install the mounting cup on the shaft. Install (bait) a nut on the shaft. Check the correct installation of a knife. Holding the stopped rod with one hand, tightly tighten the nut

On the control handle, set the ignition to the “inclusive” position. 5. On the control handle, press the gas trigger and fix it. 6. Hold the trimmer for the grass with one hand, pull the starter handle with your free hand until it is “engaged”. Pull sharply, until the first start of the engine (Fig.). Rice.9 Fig.ten

Stop a trimmer for grass 1. Release the throttle control lever. The engine should cool slightly, working at idle. 2. Transfer the ignition switch in the direction of the arrow indicated on the control handle to the Stop position. WARNING. After the production of the fuel mixture from

Maintenance 1. Air filter is cleaned or replaced by a foam element of an air filter every 10 hours of operation. The condition of the air filter is one of the main conditions of the reliable operation of the engine. Remove the air filter casing (rice.fifteen). Pull out

Old or incorrectly cooked fuel mixture. air filter. Drain the fuel mixture from the fuel tank. Pour a clean, fresh fuel mixture. Storage store a trimmer for grass is necessary in a pure form in a dry room, inaccessible to outsiders, children and animals. Before long.term storage

Unified Technical Support Service E-Mail: Servis@Huter.Su Web Site: http: // www.Huter.SU Address of your service center:

Certificate of acceptance of the gasoline trimmer for grass “Huter” of the GGT series of the GGT _ No. _ recognized as a suitable for operation, the date of sale _ I am a buyer/representative of the company with the terms

Dear buyer! We express you great appreciation for your choice. We have done our best so that this product satisfies your needs, and the quality corresponds to the best world samples. The manufacturer company sets the official service life for gasoline trimmers for grass for 5 years, at

Fuel filter

This filter cleans fuel of possible pollution. If it is clogged, gasoline does not enter the cylinder and, accordingly, the unit does not work and does not delay after starting. The fuel filter is located at the end of the intake hose, which is located inside the fuel tank. To get to the filter, you need to remove the tube with the tubes leaving the filter.

Having removed the plug, you can disconnect the intake hose and leave it in the tank. It is removed using tweezers.

Next, remove the old fuel filter from the hose and put a new one, bought in advance. It is also possible to clean the fuel filter if you do not have new. The filter should be attached to the hose using a spring clamp.

Insert the intake pipe into the cork and insert it into the tank.

It should be noted that in some models of trimmers the intake hose is located not inside the tube, but inside the tank. You can remove it with tweezers or hook.

breath

Respiratory valve. This is a check valve designed to align the pressure in the gas tank. If it clogs and does not allow air to flow into the tank, a vacuum forms inside the fuel tank, and fuel ceases to enter the carburetor. To check the valve, remove the hose from the tank to the carburetor. If the gas does not follow the tank, the air intake is clogged.

Trimmer users often ask themselves: where is the fan? This valve is usually located in the gas tank cover and looks like the next number.

It is very easy to clean the fan: disassemble the valve and rinse all its components. In some bush cutters, this valve can be located directly. On the fuel tank. You cannot find it right away, because it is hidden from the eyes under the starter case. Such a respirator is cleaned with an ordinary needle.

Exhaust channel

The reason for which the trimmer for the grass has lost power is significant, and when you are trying to increase the speed of the engine, it slowly lifts them, often due to the clogging of exhaust gases through which exhaust gases come out of the combustion chamber.

It is necessary to remove the muffler so that the burner does not get inside the cylinder. Next, clean the exhaust pipe from carbon deposits.

This should be done very carefully, avoiding carbon entering the combustion chamber.

After this procedure, the low power of the device and the low speed of rotation of the cutting head will no longer upset you.

Insufficient compression

If the compression is not enough, the engine is not possible in most cases. You can check the compression use a car compressor.

• Remove the spark plug from the engine cylinder.
• Screw the compressor in your place.
• Start tighten the starter cord in the same way as when starting the brush. Do this until the arrow on the measuring device stops moving towards the increase. This value will also show the compression force of this engine.

What should be compressed? Usually compression should be at least 8 kg / cm 2. Although even at 8 kg / cm 2, some engines do not work at idle, since the fuel is not pumped enough. If your mower does not exceed 8 kg / cm 2, you need to check the cylinder, piston and rings.

Poor compression may also be the result of a bulk carburetor. Make sure he is swinging. If so, tighten the mounts that hold it in place. Also, if the carburetor is free, you will notice that gasoline is dripping during operation.

Cleaning rules

First-and-hand, you need to decide on the location of FT. On cars with a diesel engine, the device is mostly placed above the rest of the system elements. This is provided by the design for delaying air bubbles capable of preventing the correct supply of fuel. Therefore, it is placed in an engine compartment, in some cases. under the bottom of the car.

Folding filters on gasoline ICE are located between the engine and the fuel tank. They are designed to sift small particles. In most cases, they work paired with coarse filters. mesh installed on the fuel pump.

For cleaning, use a hole or lift.

• FT bolts are unscrewed. They hold the filter lid.
• The cover is removed, the plug is disconnected.
• Next, the valve located on top of the body of FT must weaken a little. This is done to level pressure inside the filter.
• Any container for collecting fuel is placed under the drain pipe, after which it is removed.
• Then you should wait for the complete drain of the fuel in the container.
• Pull out the fixation ring out of the case.
• Remove FT with a lid.
• Wipe thoroughly with a napkin inside, and preferably a rag that does not leave a pile behind.
• Rinse in the acetone of FT and cork (is a ring), blow it well with a stream from the compressor (pump).

Water should be removed from the cartridge completely. For this, a pump is used, perfectly coping with the duty.

• The FT is put on the seal.
• The element is hoisted in its place.
• Fuel is poured on top as much as its level reaches the maximum.
• The cork is wrapped.
• Everything is collected as it was, the plug is connected.
• The motor starts, its revolutions are brought to 2 thousand/min. With this amplitude, it should work about 1 minute. The task is to avoid bullying the system.
• At the final stage, the density of fixing the hoses to FT for fuel leakage is carefully checked.

If after this difficulties with the work of the motor did not disappear, this indicates only one thing. the reason should be sought no longer in the filter. Of course, provided that the cleaning procedure was carried out according to the instructions, without errors.

A complex filter, for example from a diesel car, is better not to touch yourself. to entrust the operation to professionals. Standard FT can be cleaned with your own hands, but certain skills are needed here.

A car with a dirty FT is easy to determine by the following signs.

• Fuel consumption unexpectedly increased.
• The motor works malfunctioning, it is difficult to start or does not want to start at all.
• Nozzles fail.
• Candles, accelerators and lambda-zond wear quickly.

Electric trimmer for grass vibrates

Many mowing users noticed that some time after the device began to work, it begins to vibrate very much. On some trimmers, mainly on more expensive models, an anti.vibration system is installed in the form of shock absorbers located between the engine and the bar. But in some cases, even this does not save from strong vibrations. The cause of vibration in the trimmer can be a small amount or complete absence of oil on a hard or flexible shaft located inside the device core.

Replacing the lubrication of the hard shaft is as follows:

• unscrew the gearbox located at the bottom of the bar;

• Having removed the gearbox, you will see the end of the shaft, which must be removed to remove the part;

• After removing the shaft, it must be lubricated with a large amount of special oil “CV Joint-4” or usual. “Litol-24”;

• Apply a small amount of lubrication to the shaft and grease it evenly along the entire length of the workpiece, including grooves at the ends of the rod (if they work together, the shaft will need to be replaced);
• After lubrication, insert the shaft into the stem and replace the gearbox.
• unscrew and remove the mowing head;
• Remove the stem from the motor by unscrewing a couple of bolts;
• pull out a flexible cable from the bar;
• Lubricate the cable along its length.

To do this, you first need to lubricate the end of the cable, then insert it into the core, then, moving inside the pipe, grease the part and evenly distribute it on the surface. Then insert a flexible motor into the motor and fix it.

If the lubricant does not help and the vibration continues to occur, it is necessary to replace the flexible shaft.

Trimmer for the grass is very hot

Overheating of a trimmer for grass can occur for many reasons:

• gasoline does not have an octane number specified in the instructions of the device;
• The proportions of gasoline and oil were not observed in the preparation of the fuel mixture;
• The mixture of fuel oil was prepared for a long time (the mixture cannot be stored for more than 2 weeks);
• The trimmer for the grass works outside the set time;
• A trimmer for low.power grass used on dense and solid grass, the device is overloaded and quickly heats up;
• The displacement towards the rod or the cartridge lid jammed.

The latter will happen if you install the mower is not suitable for this device, or when the axis is shifted inside the arrow. These changes complicate rotation, increase the load on the engine, and it overheats.

How to clean an air filter motorcycles ?

How to wash or clean an air filter on a benzotrimer, benzos, experimental: Izhmash Industrial Line GT 4350.

Gasoline used in motorcycles. AI 92. The brand of gasoline is accurately prescribed in the operating instructions. Do not try to “force” the engine, filling the 95th gasoline into it. This can lead to overheating, unstable work of a trimmer for grass and breakdown.

It is not recommended to leave fuel in a trimmer tank for grass with a long break in operation. It is better to finish the working day by completely developing the entire mixture. If this is not done, then because gasoline from the engine will evaporate during the night, and the thin oil filter will remain, carburetor jacks may clog. This will cause difficulties the next engine start.

It is also necessary to observe safety precautions when storing fuel. Many pour gasoline into a plastic bottle of water. Is it worth doing so?

In no case should you store gasoline in plastic containers from under water. When mixing the fuel mixture, a static charge accumulates, you can “catch” the spark.

Therefore, at gas stations it is not allowed to refuel gasoline into plastic canists, only in metal. Before pouring gasoline in a metal canister, it is better to put it on the ground, so statics are removed from the case.

But there are situations when simple manipulations with a motorcycle do not help. The engine still does not start. In this case, we are in progress, we check the power and ignition system, guided by the rule “the motor does not work if there is nothing to burn or set it on fire”.

How to clean a carburetor on a trimmer: complex cleaning with photo description and video

If your motorcycle is already for many years, and you feel that the tool has been working with interruptions, and attempts to configure the carburetor will not be crowned with success, then it is necessary to resort to the procedure for cleaning it. To do this, dismantle the part of the tool and, using a table with high.quality lighting, proceed to the matter. Next, a step.by.step process of disassembling, repairing and cleaning the carburetor from motorcycles is presented, which will be useful not only for beginner mowers, but also by experienced craftsmen:

It is interesting! For washing, it is recommended to use gasoline or special washing liquid, the photo of which is shown below.

This is where the process of disassembly and washing is considered complete. Now let’s bring conclusions about the work done. Video on how to clean the carburetor of a trimmer for grass is presented below.

Results of work on washing the carburetor of the lawn mower

The carburetor washing procedure is not difficult, and takes no more than 1-2 hours of time. However, before starting work, you need to consider the following points:

• In the process of cleaning, you may need to replace parts and components, which should first be bought. If the lawn mower is Chinese, then difficulties may arise with the search for spare parts.
• You need to be prepared for the fact that the mechanism may not be suitable for further operation, so it will need to replace it. The cost of carburetors depends on the tool model.
• After completion of work, you will need to resort to the setup procedure. There will be no difficulties with this, since detailed instructions for adjusting gasosos and trimmers are described here.

The most important thing during work is to remember the correct location of all parts and elements. It is strictly contraindicated to use the sealant. Worn and dry gaskets should be replaced.

If you are faced with the need to clean the carburetor motorcosa, then you should not put the procedure in a long box. Prepare your tool for the next season in advance, in order not to launch the opportunity to put the adjacent territory near the house or prepare hay by winter.

TRAMMER Repair for Huter grass with your own hands

Details: Repair of a trimmer for Huter grass with your own hands from a real master for Olenord.com.

An indispensable tool for a modern summer resident or the owner of a private house is a lawn mower, which allows you to effectively and efficiently bring the adjacent territory in order. The period of active use of motorcycle is in late spring until October of the month. Modern units are equipped with powerful and hardy ICEs, enhanced transmission and main nodes. Despite this, physical wear, production marriage or improper exploitation leads to the failure of a trimmer for grass. In order to repair a trimmer for grass with your own hands, you must have at least basic knowledge in the field of technology and a little experience in its repair.

The main node of any gasoline tool is the internal combustion engine (ICE), which through various methods transmits a rotational moment to the executive body. In a modern benzocosa, a duralumin rod (pipe) is used as an element of the transmission between the motor and the trimmer head, inside of which the drive shaft is located.

Thanks to a highly reserved engine, the frequency of fishing line can reach 13 thousand revolutions per minute depending on the producer of the braid for grass. In order to exclude mechanical and temperature damage to the gearbox, a special opening is provided for the introduction of ointments in its body. As a facilitating headset for the owner, during prolonged work, all modos models are equipped with a strong belt over the shoulder.

Regardless of the manufacturer, almost every model comes with fishing line and steel knives.

The transverse section of PVC Lines for a trimmer for grass can vary from 1.5 to 3.0 mm.

Made from a durable polymer, during kosba it is subjected to intensive wear and, as a result, a break. Therefore, from time to time it is necessary to check the presence of a fishing line in the head and, if necessary, replace it. It is recommended to purchase an additional bobbin for quick replacement with a reel with a fishing line ending.

The trimmers presented today on the market for ICE grass are equipped with a D-shaped, U-shaped or T-shaped handle, where the main controls of the unit are located. For example, in a spit with a U-shaped handle key and a “stop/start” toggle switch are located on the right handle. In the D-shaped version of the gas control key, the gas adjustment key is located directly on the bar.

In view of the presence of many nodes and details, the repair of a trimmer for the grass with your own hands involves the elimination of breakdowns that prevent its normal operation. It should be noted the most basic malfunctions of gasoline cos:

• The engine of the trimmer for the grass does not gain momentum;
• Breakdown of the cylinder-piston group (CPG);
• Ignition malfunctions;
• There is no connection between the internal combustion engine and the trimmer head;
• Mechanical knocks when operating the unit.
• Repair of the CPG lawn mower

The main node of any internal combustion engine is the cylinder-piston group (CPG), which can fail due to wear of parts of parts or low quality of the fuel mixture.

Lubrication of the rubbing nodes in a benzos is carried out by adding a certain proportion of oil to gasoline. This process can be disturbed due to the old oil dropping in the form of sediment. In this situation, when the trimmer for the grass is launched, the motor overheats greatly and in a matter of minutes the most expensive breakdown occurs. To eliminate the malfunction, a complete replacement of the CPG, namely: piston, seals, cylinder and piston rings will be required. If you are not a technical engineering master and do not have experience with technicians, then the engine is unlikely to be corrected without the help of a specialist. In detail with the stages of repairing a piston trimmer for grass, you can find here.

When you fail to ignition of the lawn mower, a spark on a candle disappears and, as a result, there is no ignition of the fuel mixture.

It is important enough in the current situation not to rush with the replacement of the coil, since the cause of the breakdown may be in the absence of contact in the switch on the control handle.

An important point in the search for the ignition of a trimmer for the grass will be diagnosed with Sich, where the distance between the lateral and central electrode should be 0.5-0.7 mm. In addition, it is necessary to pay attention to the sealing ring of steel on a candle, the loss of integrity or the deformation of which can lead to etching of the combustion chamber and, as a result, reducing the power of a braid for grass.

If the replacement of the check of the electric circuit, candles and its contacts did not give positive results, then you should pay attention to the ignition module of the trimmer for the grass, namely to the gap with the flywheel. Regardless of the design features and the manufacturer of the lawn mower, the distance between the ignition coil and the flywheel should be no more than 0.2 mm. To restore the optimal value of the clearance, it will be necessary to relax the bolts of fastening the coil and a special measuring probe set the ignition of a trimmer for the grass.

A clear sign of malfunction of the engine power system is the absence of traces of the fuel mixture on the electrodes of the candle, which may be associated with the following defects:

The fuel system of the trimmer for grass

• In connection with a clogged hole in the gas tank, a vacuum is created, which prevents the normal flow of gasoline into a carburetor;
• In view of the low quality of fuel and the hit of foreign particles, the fuel filter installed in the tank clogged;
• not the intake of the mixture in the combustion chamber as a result of the carburetor.

It is possible to quickly determine the cause of the malfunction by dismantling the fuel hose leading to the carburetor. If the fuel mixture flows in a thin stream, then you should pay attention to the carburetor. In the absence of a jet, it is necessary to clean the thin needle of the cabin (a small hole in the gas tank cover) or replace the fuel filter.

If the fuel enters the carburetor, then it is necessary to clean it or adjust. Adjusting the carburetor of a trimmer for grass implies the restoration of optimal mixture mixing.

Carburetor trimmer for grass with tuning screws

To do this, pay attention to three adjusting screws: maximum revolutions (h), minimum (l) and idle (LA). First you need to configure the screws h and l, and let it go for 1 turnover each. After starting the braid and let it warm up for 10 minutes to adjust the power system in working mode. After warming the ICE, click on the gas supply key to the stop (12,000 rpm). Restore the idle mode by turning the screw La. As soon as the head of the trimmer for the grass of the start of rotation, it is necessary to wrap the screw until it stops.

#Husqvarna oil service oil filter.

I use the Husqvarna HP branded two.stroke oil for this braid.

First, I tried to connect gasoline with butter with such a makar: in a glass jar (volume of jars 2-2.5 l) with an iron-coating cover (spark protection during short-term storage of consistency) added gasoline with 250 ml of plastic polypropylene measuring glass with a scale and a nose (this is a snow.white translucent soft plastic, bought in a hogm, local production) gasoline, after which he dialed the oil with a syringe and added it, later added gasoline again. But with a syringe. hard, not comfortable and for a long time.Therefore, at the moment, I mix gasoline with butter the least like this: gasoline with the same measured glass of oil (I have a scale of 10 ml) gasoline. I later pour it into the tank through the funnel.

For almost 3 years (2013, 2014, 2015, at the moment), the duraluminated fox holders (5013304) on a trimmer head erupted almost one hundred percent (1 mm remained in some places and it would be beginning to cut the head plastic), but I took them off With the help of pliers and simply turned to insert into the same place, but the other side. Consider saved some pretty penny on buying a couple of new 5013304.

Also on days at first (in the annotation it is written that it was necessary to do this even earlier): 1.) Washed the filter with household soap, the filter became snow.white, and was beige with stains. The filter is located next to the tank, where the dark gray panel is near the motor. Undetting a dark gray circle on its surface with your fingers.2.four.) Cleaned the brass grate (protection against sparks). Located on the back of the filter, you need a special batter for a manual changing screwdriver (T20 screw. I applied the photo) to unscrew the outer panel. Snutri needed a screwdriver for a minus bars with gasoline with a brush for teeth. Was with a black raid (a spot of 10 mm), almost cleaned to a brass color, but there wasn’t much time left.

Husqvarna chainsaw. Cleaning air filter

After 1-1.5 years after the purchase, I had to replace an orange plastic handle holder (545058501), t.to. The pen began to stagger (because of which it was absolutely not comfortable to mow). But, this is my jamb, I incorrectly realized the annotation when collecting, not in the right place, fixed the handle with this holder. It was very close to the engine and the center of mass was such that the holder could not stand it and tore off the thread for the 2 screws of this holder.

The braid needs to be neatly blown, and not sharply pull the cord abruptly, they say the starter in another way.

At the moment, a fishing line to zero, previously took a bit higher (frozen, but more hacking).

When the mowing is necessary carefully near trees and bushes, t.to. Having struck a tree on a tree you kill him.In order not to kill the trees, put on PET bucks for them, cutting out of the bottles from beer (the brown is also called green, it is quite transparent that it is possible to fry a tree in the sun) and snow-white from milk and kefir. Cut the neck with universal scissors, later along the seam of the bottle down to the bottom, and cut off the bottom. C-shaped protection is released (she turns into an o-film itself) for a tree on another bush.A braid for a civilized person and accurate