Ferris mower starting problems. Ferris Zero Turn Mower Problems (With Solutions)

Ferris Zero Turn Mower Problems

Ferris zero-turn mowers are well-designed, extremely efficient and comfortable to use.

However, your Ferris zero-turn may develop a fault at any time. It may develop problems such as inequitable cuts, starting issues, vibrations and traction issues.

In this article, we reveal well-detailed Ferris zero-turn mower problems and practical fixes to ensure smooth lawn mowing operation.

Below are some of the most Common Ferris Zero Turn Mower Problems

Ready? Let’s dive right into it:

• Below are some of the most Common Ferris Zero Turn Mower Problems
• 10 Ferris Zero Turn Mower Problems and Their Troubleshooting Tips

• 1. Starting Problems
• 2. Inequitable Cuts
• 3. Difficulty In Mowing Wet Grass
• 4. Brake Not Working
• 5. Excessive Vibration
• 6. Problems with Hydro-Gear System
• 7. Engine Runs Poorly
• 8. Traction Problems
• 9. Unable to Raise the Mower
• 10. Ferris Mower Drive Problems
• Do Ferris Mowers Have Good Fuel Capacity?
• What is an iCD deck on a Ferris Mower?
• Are Ferris Mowers Comfortable?
• Are Ferris Mowers Cutting Deck Good and Strong?

• Is Ferris a Good Mower?
• What Is The Average Life Of a Zero-Turn Mower?
• Where is Ferris Made?
• Are Ferris Warranties Transferable?

Ferris Zero Turn Mower Problems and Their Troubleshooting Tips

Here are the common problems of Ferris zero-turn mowers and their possible fixes:

Starting Problems

If your Ferris zero-turn mower won’t start, it may be because of the following reasons:

• Weak connections
• Broken electrical components
• Air restriction caused by a stopped air filter
• A faulty charging system.
• Electrical problems caused by a poor battery
• Fuel restriction produced by clogged or malfunctioning fuel parts.

Fix: There are some troubleshooting tips to help fix issues with starting:

• Make sure that the fuel tank is full.
• Check if the energy level is adequate.
• Inspect the carburetor.
• Check the hydraulic system too.

Note: This is a common problem with Ferris IS 15000z

If you notice that the brake and starter are working well and you are still having issues while mowing, then, it might be as a result of damaged lifting linkages.

Fix: To solve this problem, you need to:

• Ensure that the air filter is not clogged with debris or dirt.
• If you are unable to raise the lawn mower, it is advisable to visit an authorized service center.

Ferris Mower Drive Problems

This is also one of the problems associated with Ferris’s zero-turn mowers. This happens when the mower does not run well like the standard one. This affects the functionality and operation of the zero-turn mower.

Fix: Here are some troubleshooting tips that can fix the mower’s drive problems:

• Check the deck and blades to be sure that they are functioning well.
• If the deck works well, you can then replace the blades
• If the engine cannot provide enough power, then slow-moving problems may occur. It is advisable to seek the help of a professional to help you fix the engine problem.

Note: This problem is common with Ferris IS 700z.

Maintenance Tips

• Fuel the mowing machine in the correct direction as recommended by the manufacturer.
• Store the mower when not in use.
• Check the tire pressure.
• Clean the cutting deck regularly.

Do Ferris Mowers Have Good Fuel Capacity?

Yes, they have a good fuel capacity. Ferris lawn mowers come with a broad array of fuel tanks depending on what you need. For instance, the Ferris ISX 3300 zero-turn mower is equipped with double fuel tanks. Each of these tanks has a fuel tank capacity of 5.5 gallons.

In addition, the 1SX 2200 model has a fuel capacity of 11 gallons. These mowing machines provide a smooth lawn mowing experience without stopping at regular intervals to refuel.

What is an iCD deck on a Ferris Mower?

The iCD cutting system allows for superior cut quality and better airflow discharge while mowing on lawns. The deck’s slope nose forces the grass blades forward and enables them to rise in the chamber before the blades make contact.

Are Ferris Mowers Comfortable?

Ferris lawn mowers stand out in terms of comfortability. Their zero-turn mowers, frontline mowers and front- mount mowers come with integrated suspension systems to save you from the direct impact of mowing through uneven surfaces.

This feature eliminates shocks that the chassis might transmit to your body when you ride. This will ensure a balanced and smooth riding experience.

Are Ferris Mowers Cutting Deck Good and Strong?

Yes, Ferris mowers are equipped with sturdy and durable cutting decks that can stand the test of time.

For instance, the Ferris ISX 3300’s iCD deck features a deck lift mechanism that you can easily operate with a foot pedal. Its cutting options range from 1-5 inches. Concerning its strength, its spindles are built with Hercules II cast-iron.

For a walk-behind category, the Ferris FW15 is equipped with a sturdy 32-inch deck that is made from 2.7mm fabricated construction steel. The deck features dual-timed mower blades with greaseable aluminum spindles.

Conclusion

Ferris zero-turn mowers are strong, versatile and remarkably easy to operate. Like every other lawn mower, they are not without problems. Most of these issues can be easily fixed.

Furthermore, we have outlined the problems and troubleshooting tips to help you solve the problems with your Ferris zero-turn mower.

If you are not familiar with the tools or lack the experience and expertise to manage repairs on your own, it is advisable to seek the help of a professional.

Frequently Asked Questions

Is Ferris a Good Mower?

Yes, it is worth every penny you pay. It is comfortable to use and it is well-built.

What Is The Average Life Of a Zero-Turn Mower?

A zero-turn mower can last up to two thousand hours if properly maintained.

Where is Ferris Made?

The company’s manufacturing facility is located in Upstate, New York.

Are Ferris Warranties Transferable?

Ferris lawn mowers are backed with a 2-year commercial or residential warranty which only applies to the original purchaser of the mower. The warranty is not transferable.

Sam has over a decade experience in landscape and yard maintenance. He enjoys testing and reviewing different yard tools.

Ferris Zero Turn Mower Problems (With Solutions)

Many of us have the dream of owning a lovely house and having a good life. But we can’t waste countless hours mowing our lawns in the summer just so we don’t overwhelm ourselves with that job when it comes to spring, fall and winter. As much as your grass needs to be cut, you need something to cut it with and still protect your family and pets. Enter the Ferris Zero Turn Mower. This elegant product is perfect for homeowners who want a commercial-grade set up at their home with minimal effort. But what about the Ferris Zero Turn Mower problems encountered by its users?

Zero-turn mowers have gained popularity in recent years because they have many features that people enjoy, like- control. Some say a person controls speed and direction with a zero-turn mower over a regular lawn mower. Let’s figure out the solutions to this zero-turn mower and whether it is worthy of your penny or not.

Ferris Zero Turn Mower Problems | Knowing the Product

You know that feeling when you only have a few minutes or want to get the job done quickly? The Ferris Zero Turn Mower is formulated to quench the same feeling. It’s been designed with you in mind: it has a 20” cutting deck Rapid-fire hitch for quick attachments. The Ferris Zero Turn Mower is a zero-turn mower that can turn in one direction without stopping. Designed for both residential and commercial use, the mower makes one revolution of the blade in just five seconds! This fast speed is ideal for making quick turns. The blade cuts up to 10 miles per hour, so you can make multiple passes across an area while maintaining a firm grip on the mower.

These zero-turn mowers come with two sets of adjustable blades so you can cut various grass types without having to switch attachments. The blade height is also adjustable to cater to different grass lengths and get close to obstacles such as brick walls and fences without damaging them. The machine is made from high-quality materials and measures 96.2 inches in length, which is more than enough to cover the yard in one pass. There’s a large capacity bag, too, with a 4-gallon collection zone, so you don’t have to worry about your old mower filling up with grass clippings and not being able to empty it for weeks. The tires also have a hard rubber surface, which helps reduce noise levels and makes it easier for you to move around on your property.

Ferris Zero Turn Mower Problems and their Quick fix

If your Ferris mower is making a high-pitched whining sound, the culprit could be any or all of three components: the belt, the transmission, and the blade. Fortunately, as long as you’re doing regular maintenance on your mower, there’s not too much you can do to prevent these things from happening.

You’re probably used to hearing a loud whining sound when your mower is under load. It’s the typical sound of a belt driving the blade. The belt, which is supposed to be flat and smooth, tends to buckle and shift under tension. Every time it buckles, it rubs the pulley on the crankshaft, causing that whining sound.

One way to quiet it down is by adequately tensioning the belt through its range of motion. This can be a little tricky on older mowers. It’s best to follow the three steps below:

• First, you must set the mower on a level surface and check for excessive play in the bearings. Starting with one end of the belt, wrap it around your fingers and use your hands to bounce it up and down. If you sense any excessive play, gently pry it apart until you feel no more movement.
• You should also check the pulley on the crankshaft, where your mower’s blades turn. If you pull the blade, this is where you’ll feel excessive play.
• Your last step is to add some lubrication to the belt.

If this problem persists and there are signs of wear on your mower’s bearings, it’s time to replace them. Not a Ferris consumer? Check out the issues people face with Country Clipper Mower and their solution.

Customer Reviews | Ferris Zero Turn Mower Problems

Oliver said, “The Ferris is unbelievable! I set it up myself, and in about 10 minutes, I was cutting my yard using the Ferris. It took me only 30 minutes to cut what used to take 4 hours. ”

“The mower is built with a steel frame so that you can carry it around easily without any concerns about its weight. A strong steel frame guarantees that the mower will last for several years without problems,” said Noah.

“The Ferris mower has a set of pneumatic tires. These are designed to make it easy for you to push this machine around, which is especially important if you live in a place with severe snowfall during winter,” said William.

A customer, Henry, said, “I love being able to turn on a dime, and the machine is smooth and easy to handle. You can go as slowly as you want or faster than you can walk. ”

Amelia, a happy customer, said, “The mower is well-made and was easy to assemble, using the primer and fuel (oil was already in it). It started easily – we did have a “helpful neighbor” hold it for us the first time – but can now manage without assistance.

FAQs | Ferris Zero Turn Mower

What would cause a Zero Turn Mower not to start?

Zero-turn mowers operate on a single-drive tire, making it easier to maneuver than other mowers. However, if your zero-turn mower’s engine won’t start anymore or even turn over, there could be a few different causes for this. In general, the most common causes of zero-turn mower problems include clogged fuel filters and spark plugs that have been fouled with gum and dirt. Check all the filters, hoses, and lines for obstructions and clean them off to clear any blockages. Inspect the spark plug cables to ensure they are seated securely in their spark plugs.

Is Ferris the best Zero Turn Mower?

The Zero Turn Mower is a prolific piece of machinery. Great for large yards, it can swiftly and effortlessly clear any obstacle that comes in its way. The most important part of owning one is the quality of its engine. In order they are made: Briggs Stratton, Honda, or Yamaha engines all have a lot to offer.

Conclusion | Ferris Zero Turn Mower Problems

The Ferris Zero Turn Mower’s conclusion is about versatility and convenience. There are very few Ferris Zero Turn Mower Problems, and you may surely go for it. This mower easily cuts weeds and grass, even in long, thick grass. It cuts high grass easily with its mulching kit. The lawnmower has a good cutting capacity and weighs only 165 lbs. The machine has a maximum speed of 3 miles per hour, a variable speed control, and a 45-inch cutting path. The reviews from customers and professionals on this product show that many of them were satisfied with it. There were some reports of parts breaking after only a few uses, but only about two percent of those who purchased this product. Reviews will show you how good it is to have a product like this.

Ferris Zero Turn Mower is a quality product and a good buy for the price. By mixing all of these choices, you can find the best zero-turn mower as long as you are ready to do some homework on your part. Now that you know the specifications of this item, you should go out and find one. If you are looking for a zero-turn mower made in the United States and warrants up to two years, this perfect option is the one for you to look at. Many others are on the market, but none can compete with this mower for quality and price.

Lawn Mower Ran Out Of Gas won’t Start (Here’s Why)

Running out of gas happens to me all the time. After all, mowers don’t have a fuel gauge. But when your mower won’t restart after refilling, you may be left wondering what you did wrong.

Lawnmower ran out of gas won’t start? The most likely cause of a no-start mower after running out of gas is dirt in the carburetor, but other possible causes include:

In this short post, I’ll share why dirt in the carburetor is the most likely cause of the no-start. But we’ll also cover other possible causes.

This post covers your problem pretty well, but if you need video help, check out “Carburetor cleaning video”. It covers the removal, strip down, cleaning, rebuild, and carburetor refit procedure, step by step.

Dirty Carburetor

Dirt in the carburetor is, as you know, the most likely cause of the no-start. No, it’s not a coincidence that it happens at the same time as the gas tank runs flat.

It is, as you’ve probably guessed, a result of the mower sucking the bottom of the gas tank, and that’s where all the crap lives. Your mower should have a gas filter fitted, but they don’t catch everything. Besides, the sediment in the bottom of the tank is usually so fine it has no problem passing through the fuel filter.

The fix is to clean the carburetor. Some carburetors are easier to work on than others. So just before we pull the carburetor apart, we can try a quick fix – Draining the carburetor bowl.

This is a simple job and will very often fix the problem. (more on that below)

Air-locked Gas System

Just before we get to the carburetor cleaning quick fix, I want to introduce the next highly possible cause of a no-starting mower. And that is an air-locked fuel system.

The reason I mention this now is that the fix for air-locking is the same as the carburetor cleaning quick fix. So we’ll be killing two birds and all that. You may be asking why does your fuel system air-locks when your mower runs out of gas.

Dry gas tank – A dry gas tank is also prone to air-locking.

When the fuel lines run dry, they are replaced with air. Refilling the tank pushes the air toward the carburetor. However, if the gas tank isn’t filled to the top, the weight of the gas may not be sufficient to push the air completely out of the system.

Trapped air in the fuel lines means no gas getting to the engine. The usual fix is to release the air by opening the carburetor bowl drain, but just before we do that, we’ll try to release the airlock by tapping on the gas bowl.

Tap – Try tapping on the bowl with the gas cap removed before moving on to opening the gas bowl drain bolt.

Carburetor Bowl Drain

Draining the carburetor bowl is a simple job. Many engine manufacturers include a separate drain bolt in the bowl which makes the whole job super easy. The carburetor fuel bowl is located behind the air filter and attached to the underside of the carburetor. The fuel bowl or gas bowl is a reservoir of fuel. Its job is to store enough gas to feed the engine.

The fuel bowl is designed to catch debris that makes it past the filter. There are two common types of fuel bowls, those that have a useful drain bolt and those that don’t.

Draining the bowl will release trapped dirt and air from the fuel system. It’s not a substitute for cleaning the carburetor, but as said, very often draining the bowl for a few seconds or so is enough to clear the debris.

Carburetor bowl drain bolt – This model has a drain bolt, so the bowl doesn’t necessarily need to be removed.

With the bowl drain removed, the gas should flow freely from the carb; if not, check out the fuel filter and needle seat for possible blockage.

Carburetor bowl removal – This is a common BS engine, and the bowl needs to be removed to drain the bowl.

In addition, it’s very important to clean the fuel feed bolt; this is the most common cause of no starts on this type of engine.

With the bowl removed, the gas should flow freely from the carb; if not, check out the fuel filter and needle seat for possible blockage. If draining the bowl worked out for you, fantastic, but if it didn’t, check out this guide on “Carburetor cleaning”.

Faulty Carburetor

It’s worth noting small engine carburetors cause lots of issues. I replace a ton; the symptoms can vary widely.

But hot starting issues are definitely one of them. However, the customer usually complains about hard starting issues all the time, not just after running out of gas. Some carburetors will be very obviously damaged (corrosion), but most won’t show any visible signs of damage or wear.

A faulty carburetor is on the list of suspects and will move higher on the list if you have removed the carburetor, cleaned it, and it made no difference.

Contaminated Gas

It’s worth checking the gas can you use to fill the mower. We’ve all done it; put something other than gas in the mower. It’s a simple mistake, especially if you’ve got some old gas cans from last season.

Gas only stays fresh for about a month; after that, it can cause all sorts of running problems in a small engine. If you think your gas is the problem, go ahead and drain it out, put some fresh gas in, and she should fire straight up. If she doesn’t, go ahead and drain the gas bowl as per above.

If you find you don’t use up all the gas within a month, either buy less or use a gas stabilizer in the gas can. It keeps the gas fresh for up to two years, and better than that. It protects the fuel systems of all your small engine equipment, including a two-stroke kit.

You can check it out here on “Small engine repair tool page”

Faulty Auto Choke

Auto choke is, as you may know, a feature that most modern mowers have as standard. Briggs and Stratton call theirs “Ready start.” The auto choke systems are very good, but they aren’t without fault. Auto chokes can stick in the on position causing the engine to flood.

This, however, doesn’t have any relationship to a mower running out of gas; that may simply be a coincidence. A sticking auto choke can present as an intermittent issue or a constant. You can easily check if the choke is functioning correctly. Remove the air filter when the mower’s hot, the choke plate shouldn’t be closed.

Auto chokes “On” – This is the correct choke position for a cold engine, but not a hot one.

Auto Choke “Off”

Faulty Coil

The final component on our list is the coil also known as the armature. The coil helps make the spark needed to ignite the gas inside the engine.

Coils have a tough job and are a common failure. A very common symptom of a failing coil is intermittent hot start problems. While I know this isn’t exactly a fit for your symptoms as a failing coil has no relationship with a mower running out of gas, that’s why it’s at the end of our list.

You can easily and quickly check your mower for spark. I’ve covered it in this post “Mower hard to start when hot”

Related Questions

How do you fix a mower that won’t stay running? The carburetor needs to be removed and cleaned. If the carburetor is badly corroded, it will need to be replaced.

Hey, I’m John, and I’m a Red Seal Qualified Service Technician with over twenty-five years experience.

I’ve worked on all types of mechanical equipment, from cars to grass machinery, and this site is where I share fluff-free hacks, tips, and insider know-how.

And the best part. it’s free!

Most Common Ferris Zero Turn Mower Problems And Their Solutions.

If you are looking for a zero turn mower for commercial and heavy-duty use, whether for a flat or a hilly terrain, you will find some really attractive options in the Ferris zero turn mower range.

Ferris has always offered the best range of suspension zero turn mowers. They have a high-class ICT mowing system with the fuel-protection technology which makes maintaining the oil in the engine easy.

As compared to the other popular counterparts, say the Simplicity zero turn mowers, the Ferris ZTR mowers can keep up with gasoline well at least five times better and hence, it is considered as a first choice for heavy-load mowing sessions.

Not only this, as far as user experience is concerned, they are very complacent and have a sturdy build. So, if you know how to operate a zero turn mower, you will be enthralled by this one and enjoy using it completely in your lawn.

To name a few, the Ferris ISX 800, ISX 2200 and the ISX 3300 are one of the most popular Ferris zero turn mowers. They have undoubtedly great aesthetics in terms of performance, comfort and operation.

However, this does not make them invincible and after a period of prolonged usage, they also can fall prey to maintenance issues. Even if you own one of the best Ferris ZT mowers like the Ferris ISX 800 model, it can falter too and you may end up dealing with some of Ferris ICX 800 problems.

So, today I am going to lay out the most common of the Ferris zero turn mower problems and the best methods to resolve them, without requiring any professional assistance.

Ferris Zero Turn Mower Problems And Their Solutions

Read to learn about the common problems that you can face while using a Ferris zero turn mower and along with them, I have also explained Ferris zero turn troubleshooting.

The Mower’s Engine Fails to Start;

Problem : The first issue that I am going to address today is very common which occurs on almost all the zero turn mowers at some point of time. Due to maintenance issues of some essential parts like the carburetor, the fuel filters, the spark plug etc, the engine takes really long to start. The real challenge lies in identifying the faulty part so that it can be repaired or replaced in order to start the mower’s engine.

The different reasons why your Ferris mower is unable to start, can be:

• The carburetor or the fuel lines have become clogged due to contaminated fuel;
• Dirty air filters have restricted the air flow to the engine;
• Mower’s batteries have depleted;
• The internal electrical connections have become weak or frayed out;
• Spark plug is broken or has undue carbon deposit;
• The mower’s charging system is damaged.

Solution: The above mentioned problems on the Ferris zero turn mower can be resolved by using the troubleshooting methods given below:

• Clean the carburetor and the fuel filters. Due to prolonged usage or if the fuel sits in the tank for more than a month, it becomes stale and leaves residual deposits over the carburetor and the filters. Spray carburetor cleaner on the carb and the filters to wipe them out clean and if they have become extremely clogged, it’s better to replace them.
• When the air filters are not cleaned regularly, a lot of dust and debris can accumulate over them which can clog them. If the air filters are clogged, the air supply to the engine becomes restricted and the air-to-fuel ratio becomes disproportionate, making the carburetor ‘run rich’ and throw out black smoke. So, clean the air filters using cold water or the spray cleaner regularly.
• Check the mower’s batteries and the internal electrical components. If the mower is not charging anymore, either the charging system has expired or the electrical connections are loose or disconnected. In case, there’s any wear and tear on them, let a professional intervene to change the batteries and fix the electrical connection, if required.
• Along with the electrical parts, the spark plug is an essential component of the mower. After frequent mowing sessions, it might end up bearing some carbon build up or it can become worn out. Check the plug and replace it if required.

All these above methods will ensure that the vital parts of your Ferris ZT mower are in perfect functional condition. Now, try starting the mower’s engine and see if it worked. Meanwhile, let’s learn about more issues that occur on the Ferris zero turn mower.

Bumpy and Asymmetrical Mowing Patterns;

It is very natural to expect a professional turn-out of your lawn after investing in the hefty and commercial Ferris zero turn mower. Its ICT cutting system is one reason for its popularity. But it can be disappointing to find out that the Ferris mower begins to cut the grass in an uneven and asymmetrical fashion.

Problem: This issue occurs if the mower’s blades have become blunt or the edges are damaged. It can also occur if the wheels of the mower are imbalanced or the bearings of the mower are clogged with debris, interfering with the smooth action of the blades.

• First of all, check that the mower’s blades have not become edgeless or rough. Ideally, you should sharpen the mower’s blades after every 20-25 hours of mowing.
• The blades should not be scraped or chipped off. The blades can easily become blunt if they end up hitting rocky pieces or sturdy surfaces.
• Clean the bearings of the mower regularly. After a mowing session, hay clippings and dry leaves can get stuck into the mower’s system. They can meddle with the blades’ functions and prevent them from cutting smoothly. So, keep the mower bearing clean after every mowing session.
• Lastly, if you have been using your Ferris zero turn mower for a very long time, change the blades as they start to cut clumsily after getting old.

All these preventive and curative steps will help the mower cut the grass in a spic and span manner. Just remember to maintain the mower’s blades on a regular basis.

Traction Failure;

Problem : The Ferris zero turn mower has been designed to mow large areas in particular with great ease but after a long period, you may face traction issues in the mower’s engine system due to accumulation of debris.

• Check the mower bearings and whole of the chassis on the lower portion of the mower. If there are any stuck pieces of grass or debris, brush them off to enhance the traction.
• If this does not improve the situation, it can be an engine issue. Check that the level of fuel in the engine is sufficient.

Exorbitant Vibration;

This is another very common issue with the zero turn mowers that they start to vibrate excessively when the engine starts.

Problem: It can happen if the mower’s alignment is incorrect or is overloaded. Also, if the weight is shifted more towards one side or the weight is lesser than the mower’s regular levels, the mower will vibrate.

• The first step is to check the mower’s alignment. Both the wheels should be in correct alignment and should be well-inflated.
• The weight on the mower should be balanced and none of the small or big parts should be loose. They should be tightly secured in their places.
• Next step is to check the blades of the mower. Their angle should be precise and they should be spinning freely, without any obstruction.

Engine’s Performance is Inefficient;

Problem: This one is also a maintenance issue on the mower. After using the Ferris zero turn mower for a long time, you may feel that the engine is not working as smoothly and placidly as the first few months. With time, the engines lose their efficiency and start to stall or run roughly.

• To improve the mower’s engine efficiency, the first thing to check is the level and quality of fuel in the tank. The fuel should be fresh and rich, mixed with a good quality fuel stabiliser and should not be leaking from the engine.
• The air filters of the engine must be clean. They do become blocked over time due to debris. Wipe them clean after every 2-3 mowing sessions otherwise the engine will not receive adequate air in the ignition chamber and will start smoking.
• Next step is to check the position of the throttle and the speed of the idle. Ensure that they are correctly set.
• The last step is to the gap of the spark plug should be appropriate. This is basically the distance between the electrodes of the spark plug and the straps of the ground.

If there is no gap, there would be no creation of spark and the fuel will not ignite in the mower’s engine. Alternatively, if there is too much gap, the combustion system will fail to deliver voltage required to ignite the spark, resulting in misfires.

So, the spark plug gap should be anywhere between 0.020 and 0.040 inches, not any less or more.

Keep a regular check on the above mentioned points and your Ferris mower’s engine will keep running smoothly without a hitch.

Failure in Mowing Damp Grass;

Usually we prevent mowing on damp grass but it is not always possible to wait for perfect weather as far as a commercial business is concerned. So, when you need to mow on damp grass with confidence on the mower, the Ferris zero turn mowers are one perfect solution. They are very sturdy and smartly built so that you don’t lose the steering control and find it easy to move the mower on damp grassy lawns too.

Problem: However, you might face some difficulty initially in controlling mowing and controlling the mower in wet grass. You can also face problems on wet lawn if the mower’s blades are not sharp enough and if there is debris stuck in the braking system.

• When the blades are razor-sharp, the mower will easily move through wet grass and cut it without getting stalled. So, ensure that the mower’s blades are knife-like sharp and clean before you start to mow a damp lawn.
• In this situation, one important thing to maintain is the mower’s speed. Don’t run the engine very fast to avoid skidding. With a slow speed, the blades will move sharply through the grass and cut precisely.

With these points, you will be able to steer the mower firmly through wet lawns but remember to clean the mower’s blades afterwards as the wet grass clippings should not remain stuck on the blades and the wheels.

Failure of Mower’s Hydrostatic Transmission;

The hydrostatic system of the Ferris zero turn mowers is one of their strengths as these mowers don’t use the gears but the hydraulic fuel to power up the engine.

Due to this technology, they are more stable, competent and their parts don’t die out faster as compared to the other mowers.

Problem: One issue with Ferris zero turn mower’s hydrostatic transmission system is the penetration of air into the fuel lines.

• Sometimes, air can make way into the fuel lines and the connectivity of the hydraulic fuel to the engine is affected. Then, sufficient pressure is not built by the system and the engine does not start.
• Also, if the hydraulic fuel is stale, the drive belt or the mower’s pulleys are loosened or broken, the hydrostatic transmission system can fail.
• First of all, evacuate all the air that has gone into the system using a hydro-gear pump. Contact a professional to do this if you face difficulties in using the pump.
• Check that the drive belt and the mower’s pulleys are in a functional state. If the belt is flapping or if the pulleys are broken, replace them.

The hydrostatic transmission system of any zero turn mower thrives on regular maintenance. So, keep the hydraulic fuel fresh and prevent air from getting trapped into the system.

Brakes Stop Functioning;

The brakes of any riding mower are one of the most critical parts and for the mower to cut evenly and sharply across the lawn, the blades need to be sharp and rightly angled.

Problem : In most of the cases, it is the broken callipers of the brakes which prevent the mower from trimming the grass precisely. As mentioned above, if the blades are blunt or the adjustment has gone wrong, they won’t move and the mower’s brain system will give up.

• Check the brakes of the mower and ensure that their adjustment and alignment is correct.
• They should not be bent or crooked at the edges.
• Clean the brakes if any grass clipping, small stones or dry leaves have gotten stuck in the braking system.

Make it a habit to sharpen the blades and clean them after each mowing session so that if by chance they have chipped off their edges, they can be replaced timely.

Difficult to Raise the Mower’s Deck on an Uneven Areas;

Problem: It is important to be able to raise the mower’s deck when you are on rough uneven terrain. Controlling the mower’s turns and balancing it comes with a lot of practice but if you have a great hand at mowing but still face difficulty in raising the mower’s deck when required, there might be an issue with the linkages of the lifting.

• Check the links of the lifting system of the mower. The links can go out of place after a period of time or can wear out. Replace the defective parts if required.

Difficulty in Turning the Wheels;

Problem: If you struggle in taking turns or moving the mower around with ease, mostly it is due to unequal pressure in the mower’s tires. If any of the tires is deflated or punctured, you cannot turn around the mower smoothly and if you continue forcing the mower to move in such a situation, the tires can get damaged.

• Check that the tires are adequately infected and have equal pressure.
• Also, lubricate the mower with a steering oil regularly.

Just like that, with all these Ferris zero turn troubleshooting methods, you will be able to resolve all the issues on the Ferris mower and if you pledge to maintain it regularly, the Ferrois zero turn mowers can provide loyal service for a prolonged period of time.

Frequently Asked Questions

Q1. How many hours does a Ferris zero turn mower last?

Answer – In general, the Ferris zero turn mower can easily last up to 2000 hours, without having any major repairs.

Q2. When should I change the oil in my Ferris zero turn mower?

Answer – The Ferris zero turn mowers are exclusively equipped with an Oil-guard system by the Vanguards. This oil-guard system can extend the life of oil in the tank by 500%. This means that the mower can easily go on for 500 hours without changing the oil which cuts down on the cost of oil in the mower.

Q3.What kind of oil is used in the Ferris zero turn mowers?

Answer – The Ferris zero turn mower uses premium quality detergent oil like ‘For Service SF, SG, SH, SJ’ or high. Synthetic oils also can be used which work well in all the temperatures.

Q4. Which is the biggest Ferris zero turn mower?

Answer – Out of all the models of the Ferris zero turn mowers, the WZ100 is the biggest model with a huge cutting width of 120”. It has five 25” flex decks and excellent manoeuvrability. It is also the biggest zero turn mower in the world with the strength and precision of about five medium size mowers.

Q5. What engine is used in the Ferris zero turn mowers?

Answer – The Ferris zero turn mowers have the Vanguard engine with EFI and ETC which are considered the most premium in terms of lawn maintenance and care. Both the technologies are known for curating models with a smooth start and consummation.

Conclusion

It is normal to feel anxious when you face any issues with these excellent quality Ferris suspension zero turn mowers. However, you must have understood by now that over a period of regular usage, such issues can crop up on any of the zero turn mowers but they can be resolved easily.

Ensure that the fuel is fresh and add a fuel stabiliser each time you refill the tank. Keep a regular check on the mower’s brakes, the spark plug, the fuel pump, the hydraulic fuel and keep the tires well-inflated.

With these tips, the Ferris zero turn mower won’t stall and will keep operating at the best of its efficiency. Leave a comment in the Комментарии и мнения владельцев section if this article proved valuable to you in resolving issues on the Ferris zero turn mower.