How To Cut A Mirror At Home
How to cut a mirror neatly and easily at home
Well, let’s start another lesson on the blog Best houses with a little common truth. “work can only be done efficiently when a good tool is used.” Of course, this truth also applies to cutting mirrors, which we will talk about today. There are two types of glass cutters: diamond and roller, and a mirror at home can be cut by both. For diamond, the cutting part is a piece of technical diamond, and for the roller. a wheel made of a special alloy of increased strength.
How to Cutting Glass at home Glass Cutting blade Methods and Tricks
Mirror surface preparation
First, the entire surface of the mirror must be thoroughly cleaned and rinsed with a soda solution. If there are traces of stains, then it is a good idea to clean such areas with alcohol, otherwise the cut line may “go” sideways, and the glass will be damaged. The place where the cutting will take place must be flat so that the mirror fits snugly over the entire surface. In addition, it should not be hard. it is better to spread a soft cloth. After that, the mowing line of the cut is marked.
Then you need to attach a ruler to the mowing line, preferably a metal one. For greater accuracy, you need to prepare a ruler. Two erasers (school eraser) are attached to its ends (for example, with adhesive tape). This will raise the ruler slightly above the surface of the mirror. This technique allows you to control the correct position of the cutting edge of the glass cutter and ensures that the glass cutter does not jump off this mowing line onto the line.
Glass cutting
It is understood that the cutting element must be positioned strictly on the marked mowing line and perpendicular to the surface of the mirror. With a slight pressure to the glass, they lead it towards you. There is no need to rush. The pressure and movement of the glass cutter must be smooth and progressive. If everything is done correctly, then the sound of glass being cut is heard, it is impossible to confuse it. A creak indicates either the unsuitability of the instrument, or its incorrect position, too strong pressure. When properly cut, a thin white line will remain on the surface of the mirror.
When the cutting line is ready, the mirror lies on the edge of the surface (table, workbench, stool). You need to put it so that the line protrudes slightly over the edge. After that, holding the mirror with one hand, the other should be slightly pressed down. the cut off part should fall off. If this does not work, then with a small hammer you need to knock on the bottom of the entire mowing line, moving the hammer from its far end towards you. After that, if the piece does not separate, the cutting process should be repeated.
If possible, it is better to purchase a diamond glass cutter. it cuts better and has a longer service life. When using it, you need to focus on the marks, since it has two angles: sharp and obtuse.
When cutting glass, it is best to use safety glasses. If they are not there, then you should not tilt your head too low to avoid damage to the eyes by glass fragments.
See the details of the mirror cutting process on
How to prepare the glass for the procedure?
So that the line of the cut does not “go” sideways in the future, the first thing to do is to clean the surface of the product and rinse it with soda. If stains and dirt are difficult to wipe off, use rubbing alcohol. The old mirror can be washed with special glass fluids. It is not necessary to wipe it off with a cloth after cleaning, as it will definitely leave unnecessary lint.
After that, if the piece does not separate, the cutting process should be repeated.
If you have just purchased a mirror, you need to leave it indoors for a couple of hours, where the entire cutting process will be carried out. During this time, the product adapts to the temperature and humidity of the room. Then, if the mirror was previously in the box, wipe it with paper towels.
If possible, it is better to purchase a diamond glass cutter. it cuts better and has a longer service life.
Make sure that the place where you will be cutting is perfectly flat, otherwise the product will not fit snugly on the surface. Think of a soft bedspread to cover the tabletop. Place the product in your work area with reflective side up.
When cutting glass, it is better to use protective glasses.
The main thing is to do the work calmly and accurately, and then you will succeed.
The next step is to mark the cut mowing line. Remember the adage “measure seven times. cut once”? She fits our situation perfectly. After measuring, carefully trace the line to be cut with a wax pencil. Then attach a metal ruler to it. Don’t forget to put pieces of rubber or leather underneath.
In some cases, rubber-padded pliers are used to remove cut pieces of a thin mirror.
Now all you have to do is insert the mirror into a pre-prepared frame.
Required tools
Be sure to check that all materials are present before trimming the mirror. The table will fit the most standard, the main thing is that the dimensions of the table top correspond to the area of the mirror surface, ideally exceed it.
There are two types of glass cutters: diamond and roller, and a mirror at home can be cut by both.
If you are planning to insert a mirror into the frame, get one in advance.
Then you need to attach a ruler to the mowing line, preferably a metal one.
Work should be done carefully, without haste.
The most important tool is, of course, the glass cutter. The tools with which you can cut glass at home are of three types:
- roller. the cutting part is made of an extra strong alloy;
- diamond. technical diamond is used as a cutting part;
- oil. have the same characteristics as roller, there is an additional reservoir.
This technique allows you to control the correct position of the cutting edge of the glass cutter and ensures that the glass cutter does not jump off this mowing line onto the line.
If you are wondering which glass cutter to buy, choose a diamond one. It surpasses the roller in both quality and service life.
It is clear that the cutting element must be located strictly on the marked mowing line and perpendicular to the surface of the mirror.
During operation, the glass cutter is firmly pressed against the surface of the mirror and the ruler.
Another necessary tool is a special thick ruler or square for cutting glass. However, you can use a regular metal ruler, you just need to slightly improve it. To do this, you will need some rubber or leather pieces. You need to put a ruler on them. This will prevent the metal from sliding on the glass and raise the ruler to a level high enough to stop the glass cutter.
The pressure and movement of the glass cutter must be smooth, progressive.
You will also need pliers and a hammer, which is designed to make it easier to break the glass by tapping the mirror from the back. It is desirable that the hammer is small.
When properly cut, a thin white line will remain on the surface of the mirror.
The specialist is able to determine by ear the correctness of the cutting. by the characteristic slight crackle.
It is highly advisable to cover the countertop with a blanket. The fabric should be natural and have the necessary density, because you will manipulate the mirror on it. If not used, the fragile glass can crack on the hard surface of the table with any careless movement.
When the line of the cut is ready, the mirror lies on the edge of the surface (table, workbench, stool).
The last element is a water-soluble marker or wax pencil for marking.
If this does not work, then with a small hammer you need to knock on the bottom of the entire mowing line, moving the hammer from its far end towards you.
How to cut a mirror at home
Glass cutting safety
Before cutting a mirror with a glass cutter, read the safety requirements.
- Tidy up the workplace, remove everything unnecessary from the table. Place scrap boxes, tools and the product in place.
- Make sure all fixtures are in good working order.
- Put rubber tips on the lips of the pliers or wrap with something.
- Glass boxes are always stacked vertically.
- Be sure to use special suit, gloves and goggles.
- Take your time and try not to make sudden movements.
- Do not touch the cutter line of the glass cutter with fingers not protected by gloves.
- It is forbidden to cut the product on objects not intended for this.
- When working at a height, the glass must not be thrown down. Always take scraps and whole glass with you.
- It is permissible to cut only in the direction opposite to the direction of the cutting part.
- It is necessary to install the glass at strong supports with an inclination of up to 15 °.
- In the process, put unnecessary trimmings in a box and send them to the trash can as they accumulate.
- Remove glass from drawers carefully. If the glass is cracked, remove it in separate pieces.
- You can not cut the product on your knees.
- Use electric glass cutters with care.
- If the product is brought in from the cold, be sure to warm it up.
- Sweep the floor and clean the workbenches with a special brush. Do not try to blow off glass dust.
- Before finishing work, shake the suit thoroughly, cleaning it of crushed glass particles.
First, the entire surface of the mirror must be thoroughly cleaned and rinsed with a soda solution.
The place where the cutting will take place must be even so that the mirror fits snugly over the entire surface.
Let’s start cutting
The glass cutter must be at right angles to the mirror surface, strictly on the marked mowing line. Slightly pressing against the glass, it must be carefully guided in the direction leading to you. Do not hurry. Move the glass cutter gently and precisely along the intended mowing line. If you hear the sound of glass being cut, then everything is going well. A creak indicates that the cutter is broken or you are doing something wrong.
An old mirror will help you clean up special glass liquids.
When properly cut, you will see a thin line on the glass. If all goes well, place the mirror on a workbench with the line protruding slightly over the edge. Then press down slightly on the cut part, holding the other hand with the other. The glass should fall off. If this does not happen, tap the entire line with a hammer from the bottom side, moving it towards you. Does not work? Repeat the cutting procedure again. Small fragments are removed with pliers.
If you have just purchased a mirror, you need to leave it indoors for a couple of hours, where the entire cutting process will be carried out.
Attention! If you do not have special glasses, do not lean too low when working in order to avoid getting debris in your eyes.
A creak indicates that the cutter is broken or you are doing something wrong.
It is done!
The work is almost finished. Now all you have to do is insert the mirror into the previously prepared frame. If not, cover the sharp edges with sandpaper to protect yourself from cutting.
When cut correctly, you will see a thin line on the glass.
As you can see, the glass cutting procedure is not that difficult. The main thing is to do the work calmly and accurately, and then you will succeed.!
If all goes well, place the mirror on a workbench with the line protruding slightly over the edge.
Glass cutting safety
Before cutting a mirror with a glass cutter, read the safety requirements.
- Tidy up the workplace, remove everything unnecessary from the table. Place scrap boxes, tools and the product in place.
- Make sure all fixtures are in good working order.
- Put rubber tips on the lips of the pliers or wrap with something.
- Glass boxes are always stacked vertically.
- Be sure to use special suit, gloves and goggles.
- Take your time and try not to make sudden movements.
- Do not touch the cutter line of the glass cutter with fingers not protected by gloves.
- It is forbidden to cut the product on objects not intended for this.
- When working at a height, the glass must not be thrown down. Always take scraps and whole glass with you.
- It is permissible to cut only in the direction opposite to the direction of the cutting part.
- It is necessary to install the glass at strong supports with an inclination of up to 15 °.
- In the process, put unnecessary trimmings in a box and send them to the trash can as they accumulate.
- Remove glass from drawers carefully. If the glass is cracked, remove it in separate pieces.
- You can not cut the product on your knees.
- Use electric glass cutters with care.
- If the product is brought in from the cold, be sure to warm it up.
- Sweep the floor and clean the workbenches with a special brush. Do not try to blow off glass dust.
- Before finishing work, shake the suit thoroughly, cleaning it of crushed glass particles.
First, the entire surface of the mirror must be thoroughly cleaned and rinsed with a soda solution.
The place where the cutting will take place must be even so that the mirror fits snugly over the entire surface.
Let’s start cutting
The glass cutter must be at right angles to the mirror surface, strictly on the marked mowing line. Slightly pressing against the glass, it must be carefully guided in the direction leading to you. Do not hurry. Move the glass cutter gently and precisely along the intended mowing line. If you hear the sound of glass being cut, then everything is going well. A creak indicates that the cutter is broken or you are doing something wrong.
An old mirror will help you clean up special glass liquids.
When properly cut, you will see a thin line on the glass. If all goes well, place the mirror on a workbench with the line protruding slightly over the edge. Then press down slightly on the cut part, holding the other hand with the other. The glass should fall off. If this does not happen, tap the entire line with a hammer from the bottom side, moving it towards you. Does not work? Repeat the cutting procedure again. Small fragments are removed with pliers.
If you have just purchased a mirror, you need to leave it indoors for a couple of hours, where the entire cutting process will be carried out.
Attention! If you do not have special glasses, do not lean too low when working in order to avoid getting debris in your eyes.
A creak indicates that the cutter is broken or you are doing something wrong.
Required tools
Be sure to check that all materials are present before trimming the mirror. The table will fit the most standard, the main thing is that the dimensions of the table top correspond to the area of the mirror surface, ideally exceed it.
There are two types of glass cutters: diamond and roller, and a mirror at home can be cut by both.
If you are planning to insert a mirror into the frame, get one in advance.
Then you need to attach a ruler to the mowing line, preferably a metal one.
Work should be done carefully, without haste.
The most important tool is, of course, the glass cutter. The tools with which you can cut glass at home are of three types:
- roller. the cutting part is made of an extra strong alloy;
- diamond. technical diamond is used as a cutting part;
- oil. have the same characteristics as roller, there is an additional reservoir.
This technique allows you to control the correct position of the cutting edge of the glass cutter and ensures that the glass cutter does not jump off this mowing line onto the line.
If you are wondering which glass cutter to buy, choose a diamond one. It surpasses the roller in both quality and service life.
It is clear that the cutting element must be located strictly on the marked mowing line and perpendicular to the surface of the mirror.
During operation, the glass cutter is firmly pressed against the surface of the mirror and the ruler.
Another necessary tool is a special thick ruler or square for cutting glass. However, you can use a regular metal ruler, you just need to slightly improve it. To do this, you will need some rubber or leather pieces. You need to put a ruler on them. This will prevent the metal from sliding on the glass and raise the ruler to a level high enough to stop the glass cutter.
The pressure and movement of the glass cutter must be smooth, progressive.
You will also need pliers and a hammer, which is designed to make it easier to break the glass by tapping the mirror from the back. It is desirable that the hammer is small.
When properly cut, a thin white line will remain on the surface of the mirror.
The specialist is able to determine by ear the correctness of the cutting. by the characteristic slight crackle.
It is highly advisable to cover the countertop with a blanket. The fabric should be natural and have the necessary density, because you will manipulate the mirror on it. If not used, the fragile glass can crack on the hard surface of the table with any careless movement.
When the line of the cut is ready, the mirror lies on the edge of the surface (table, workbench, stool).
The last element is a water-soluble marker or wax pencil for marking.
If this does not work, then with a small hammer you need to knock on the bottom of the entire mowing line, moving the hammer from its far end towards you.
How to prepare the glass for the procedure?
So that the line of the cut does not “go” sideways in the future, the first thing to do is to clean the surface of the product and rinse it with soda. If stains and dirt are difficult to wipe off, use rubbing alcohol. The old mirror can be washed with special glass fluids. It is not necessary to wipe it off with a cloth after cleaning, as it will definitely leave unnecessary lint.
After that, if the piece does not separate, the cutting process should be repeated.
If you have just purchased a mirror, you need to leave it indoors for a couple of hours, where the entire cutting process will be carried out. During this time, the product adapts to the temperature and humidity of the room. Then, if the mirror was previously in the box, wipe it with paper towels.
If possible, it is better to purchase a diamond glass cutter. it cuts better and has a longer service life.
Make sure that the place where you will be cutting is perfectly flat, otherwise the product will not fit snugly on the surface. Think of a soft bedspread to cover the tabletop. Place the product in your work area with reflective side up.
When cutting glass, it is better to use protective glasses.
The main thing is to do the work calmly and accurately, and then you will succeed.
The next step is to mark the cut mowing line. Remember the adage “measure seven times. cut once”? She fits our situation perfectly. After measuring, carefully trace the line to be cut with a wax pencil. Then attach a metal ruler to it. Don’t forget to put pieces of rubber or leather underneath.
In some cases, rubber-padded pliers are used to remove cut pieces of a thin mirror.
Now all you have to do is insert the mirror into a pre-prepared frame.
How to cut a mirror at home
It is done!
The work is almost finished. Now you just have to insert the mirror into the previously prepared frame. If not, cover the sharp edges with sandpaper to protect yourself from cutting.
When cut correctly, you will see a thin line on the glass.
As you can see, the glass cutting procedure is not that difficult. The main thing is to do the work calmly and accurately, and then you will succeed.!
If all goes well, place the mirror on a workbench with the line protruding slightly over the edge.
Work protection
Safety is considered to be one of the most important factors in any type of work, and glass cutting is no exception. This material, in its raw form, has sharp edges and its fragile structure can contribute to the formation of small fragments. When working with glass or mirrors, it is strongly recommended to protect your hands and eyes to avoid injury. To do this, you can use the following things:
Construction gloves (preferably rubberized). You can use any others, the main thing is that they do not slip much on the glass surface. For added safety, fingers can be wrapped with adhesive tape over gloves.
Protective glasses. It is not necessary to use special construction. You can wear regular reading glasses or sunglasses. If only they do not obstruct visibility.
Curly cutting
Cutting technology is similar. It differs only in that it is necessary to make a pattern.
The main difference is in the withdrawal procedure. Break off unnecessary sections in parts, dividing them into sections with more or less equal shares according to the degree of curvature or angles of inclination to a straight line. To facilitate breaking by hand, cut additional mowing lines with a glass cutter from the highs and lows of the curve to the outer edge. Circles or ovals are simply broken up into a series of segments.
Let’s start cutting
The glass cutter must be at right angles to the mirror surface, strictly on the marked mowing line. Slightly pressing against the glass, it must be carefully guided in the direction leading to you. Do not hurry. Move the glass cutter gently and precisely along the intended mowing line. If you hear the sound of glass being cut, then everything is going well. A creak indicates that the cutter is broken or you are doing something wrong.
An old mirror will help you clean up special glass liquids.
When properly cut, you will see a thin line on the glass. If all goes well, place the mirror on a workbench with the line protruding slightly over the edge. Then press down slightly on the cut part, holding the other hand with the other. The glass should fall off. If this does not happen, tap the entire line with a hammer from the bottom side, moving it towards you. Does not work? Repeat the cutting procedure again. Small fragments are removed with pliers.
If you have just purchased a mirror, you need to leave it indoors for a couple of hours, where the entire cutting process will be carried out.
Attention! If you do not have special glasses, do not lean too low when working in order to avoid getting debris in your eyes.
A creak indicates that the cutter is broken or you are doing something wrong.
DIY cutting mirrors
Cutting mirrors differs from cutting glass in that it is done from the front. The rest of the conditions are the same, which means you must have:
- table, surface area is greater than the size of the mirror;
- a long ruler or strip of hard material about 8 mm thick;
- glass cutter;
- small hammer and pliers.
It is desirable to have a soft and non-slip natural cloth and a few small thin pieces of rubber or leather. By the way, leather pieces are much easier to find.
All this is true when it comes to simple cutting of the mirror.
Curly will require additional conditions:
- availability of sheet material for the manufacture of patterns (plywood, fiberboard, HDF);
- jigsaw or boot knife.
Work technology
The table or other flat surface is covered with an old sheet or bedspread so that the product does not slip during cutting and is not accidentally scratched. The mirror is placed with the reflective side up.
Cutting the mirror begins with marking, this procedure must be approached responsibly. First, you need to measure and check everything several times, in this case you cannot rush so as not to spoil everything. After that, a ruler is applied to the marked lines.
To properly cut the mirror, the glass cutter is located at an angle of 90˚ (or slightly less) to the mirror surface of the product, the movement of the hand must be clear and confident. Slightly pressing, the tool is guided from the far point towards you. In this case, the sound of the glass being cut should be heard. An unpleasant squeak will indicate that the cutter is broken or something has gone wrong.
If everything went well, a thin line will remain on the product. Then the mirror is placed on the table so that the cutting line protrudes slightly over the edge. With one hand they hold the main part of the product, and with the other they gently press on the cut off part, which should separate under pressure.
If a white, intermittent line remains after the cutter, the procedure will have to be repeated. The new line is drawn 2 mm further from the line. Before cutting the glass, it is recommended to practice on unnecessary fragments in order to determine the pressure of the glass cutter and cut the strip exactly.
When working with a roller glass cutter, it is recommended to moisten the cutting area with turpentine, since this tool requires a lot of effort.
If there is no separation, then on the mowing line of the cut from the lower side towards you, you will need to gently knock with a hammer. The remaining small fragments are removed with pliers. If necessary, the edges of the cut are cleaned with sandpaper. The edge of the product is treated with a sealant or transparent varnish. The finished mirror is fixed in the prepared frame.
Precautions
Safety engineering is of great importance when cutting mirrors at home. Compliance with it will save you from possible injuries and will help not to spoil the mirror during operation.
To ensure complete safety, you will need:
- put in perfect order at the future workplace, remove all unnecessary, containers for waste and the tool required for work to arrange so that they are freely available;
- before starting work, you need to make sure that the glass cutter and pliers are in good condition;
- the cutting process should be started in a calm state, without excitement, all movements should be smooth, sharp should be avoided;
- in order to avoid cuts, do not touch the edges of the glass with your hands without protective equipment;
- you cannot cut the mirror on surfaces that are not suitable for this;
- in the event that work is carried out high above the ground, it is strictly forbidden to dump the cuttings down, they must be taken with you;
- when removing pieces of mirrors, you should be careful: if they are cracked, you need to take only one fragment at a time;
- when moving the mirror from a room with a low temperature to a warm one, you need to give it time to warm up;
- dust and crumbs left after cutting must be removed with a special brush, in no case must be blown away;
- if you were wearing overalls, then before taking them off, you need to thoroughly shake off.
We must not forget about safety measures, they must be observed during work.
If suddenly it is not possible to provide the necessary conditions for the process of cutting mirrors, then it is better to postpone it for a more suitable time.
Finishing Tips
- Practice on the unnecessary pieces of the mirror first.
- If the cut line is straight, for example for a square mirror, lay it on a flat surface so that the cut extends just a little beyond the edge of the table. Press down on the canvas, hold it with one hand, and on the other hand, push down on the free edge. This will give you a clean break.
- If the shape required a minor cut, then use a steel ring cutter.
- If you need to separate the canvas along wavy cuts, turn the mirror over, place it on foam plastic, cardboard or any other springy surface, press on the mowing line with your index finger, then the cut should split.
Once the mirror is detached, you can insert it into the frame or sand the edge with fine-grained paper. This way you can avoid accidental cuts.
Do not be afraid to cut the mirror at home, the main thing is to do everything carefully and deliberately!
Glass cutting technology principle
Here’s how to properly cut a mirror with a glass cutter at home:
- First you need to prepare the mirror surface and tools.
- After that, mark up with a ruler and marker. For the curly version. use special patterns.
- Then carefully draw the line with a glass cutter, observing the constancy of pressing.
- Then very gently tap with a hammer, through several layers of fabric, the edge of the mirror, which will need to be removed. Before this, it is previously slightly suspended from the edge of the table, without fail supporting it so that the mirror or glass does not fall to the floor.
- After that, the work is carried out on a break. That is, they are trying, by applying minor efforts, to break off an unnecessary piece from the base. Then wipe the cut edge with a damp cloth, which was previously folded in several layers. This is done in order to remove small glass particles.
Get professional advice when cutting mirrors.
Rules for using a glass cutter
So, how to cut a mirror at home is not so easy, especially without skills, you need to know exactly how to use a glass cutter correctly.
- Initially, you need to check the tool. it should not be loose and the wheel should rotate smoothly. This is a prerequisite for round glass cutters.
- If you need to cut a mirror with a diamond glass cutter, then you need to make sure that the stone is fixed securely enough and at the correct angle.
- The pressure should be even and smooth. Even slight deviation from constant pressure force and the mirror surface will crack.
- When carrying out manipulations, it is necessary to listen to the sounds that the instrument makes. There should be no squeaks. If, nevertheless, sounds appeared, this means that the glass cutter has already become dull.
Additional Information! If the cut is made with a deviation from the established mowing line, do not try to fix the defect. You just need to step back a few millimeters in the desired direction and re-cut the line. This is a prerequisite for both straight and curly ways of cutting out mirrors and glass.
Precautions and safety measures
Before cutting off the mirror, you need to understand that this type of activity carries a potential threat to the performer.
Many design projects require custom mirrors in the interior.
Therefore, in order to protect yourself from unforeseen industrial injuries, it is important to adhere to the following safety measures:
- Always wear safety glasses and gloves. Eye protection is required, since small fragments that can accidentally fall on the mucous membrane will subsequently cause irreparable damage to the organ of vision.
- Prepare a special box into which the production scraps will be stored. It is imperative to do this to prevent small pieces of glass from getting on or cutting your clothes.
- The surface on which all manipulations will be carried out must be extremely flat and large in area. All the tools and materials at hand should also be nearby.
- After you cut glass or a mirror at home, you need to wipe the work surface and the floor around it with a damp cloth. This manipulation must also be performed with all precautions. Otherwise, you can drive small fragments under the skin, which will be quite problematic to get rid of later.
Before cutting a mirror with a glass cutter, read the safety requirements.
How and how to cut a mirror at home
Reading time:
Sometimes, when it is not possible to take the mirror to the workshop in order to cut the desired size and shape, such a manipulation can be carried out at home.
How to cut a large mirror without breaking it
Mirror is an integral part of any interior.
But, for its successful completion, it is necessary to know the basic technological steps of glass cutting, with what tools it can be done, and also not to forget about the precautions.
- Precautions and safety measures
- Necessary tools and materials for cutting glass at home
- Rules for using a glass cutter
- Mirror surface preparation
- Glass cutting technology principle
- Is it possible to cut glass without a glass cutter at home
- cutting mirrors with glass cutter
Necessary tools and materials for cutting glass at home
To know how to cut a mirror correctly, you need to understand not only technological actions, but also what tools it will be carried out.
There are special tools for cutting mirrors.
Here is a list of everything you need:
- High quality diamond glass cutter. It is he who will allow not only to quickly and accurately cut ordinary glass, but also to cope with tempered.
- If it is decided to use an angle grinder for manipulation, then it must be equipped with a diamond-coated disc. But, it is worth remembering that in this case there is a high probability of crumbling the material.
- You also need a large and always flat surface. The main condition is full adherence of the glass over the entire area to the table. It is easy to avoid cracking.
- You will also need a hammer and pliers.
- For marking, you need to take a long ruler and a square. You will also need a marker for marking.
- If it is necessary to carry out curly cutting of a mirror, then you will also additionally need. already made patterns (they can be made of thick cardboard or plywood), as well as a knife for shoemaking or a jigsaw.
Important! If you need to cut tempered glass at home, it is best to do the work on a machine that is equipped with a diamond-coated wheel. In this case, the process of crumbling the heavy-duty mirror or glass can be avoided.
Mirror surface preparation
It is important to understand that before you start manipulating a mirror or glass, it must be wiped in order to remove all dirt and dust from the surface. But, it is better to do this with baking soda, as it helps better cleanse. If the soda turned out to be powerless in front of any stains, then you can apply alcohol.
Use modern mirror cutting techniques.
It is also allowed to use a special liquid for glass. It does not matter which cleaning liquid was used, after that, wipe the surface dry on both sides with a cloth that has a good level of hygroscopicity. Only she will allow you to collect all the remaining moisture.
Carefully start cutting the mirror.
Is it possible to cut glass without a glass cutter at home
Not everyone knows that ordinary glass can be cut using the most familiar scissors. The main conditions in this case are sharp. sharpening of the cutting edge. In this case, it is necessary to place all the glass in a sufficiently large container so that it is covered with water.
Sometimes there is a desire to acquire a mirror of some intricate shape.
It is the liquid that prevents the appearance of chips and cracks. Then, carefully with scissors, begin to cut off small pieces, achieving the desired shape and size.
Cut a mirror of any shape.
Note! This version of mirror processing is suitable only if its thickness does not exceed the 4 mm mark and it is necessary to perform curly cutting. Most likely, in this case, you will not be able to cut off the straight line.
You can use another way. For example, take a file with a rectangular or triangular cutting edge.
The cutting element must be positioned strictly on the marked mowing line and perpendicular to the mirror surface.
The technology of actions in this case is as follows. cuts are made with the edge of the file on both sides. Then the main line is scratched and breaking off is carried out. But, to implement this option, you need the skill of working with materials such as glass and mirror.
If you have never worked with a mirror, then get help.
You can also try using a winder drill. Here, holes are made in several places. They all lie on the cut line. Then a thin line is scratched between them and tapping, and the unnecessary part is eliminated by breaking off.
If everything is done correctly, then the sound of glass being cut is heard, it is impossible to confuse it.
Important! If the work is carried out with a drill, then it must be turned in such a way that only an acute angle enters the glass. Otherwise the mirror will crack.
Given all these features, at home it is quite easy to trim or curly cut out a mirror.