How to cut an acrylic plinth for a bath. Varieties of a plinth on a bath

Bath plinth: neat and practical joints

No matter how hard you try to install the bathroom close to the wall, it will not work to do it perfectly. Since there are no completely even walls in any house, one way or another there will be a small gap that water will fall into. Previously, a cement solution was used to solve this problem in combination with oil paint. However, now there is a more modern and simple solution. a bathtub skirting board. Consider all possible options for decorating the border, as well as their features.

The bathtub for the bath will protect the walls and floor from the water and will become a harmonious decoration of the bathroom

Features of the choice and application of talkers for baths

In addition to the fact that the open gap behind the bathroom does not look aesthetically pleasing, the open joint can cause mold and fungus, which is first of all unsafe for health. That is why it is necessary to take care of its sealing and buy a border for a bath.

The bathtub brings protects against water and prevents the development of fungus and mold

Moisture falling into the joint dries for a very long time and often leads not only to the development of undesirable microorganisms, but also to the emergence of corrosion processes on metal elements located behind the bathroom. And since it is much easier to prevent these processes than to deal with them subsequently will consider what can be done to avoid this.

In the process of choosing a skirting board, the following points must be taken into account:

• the cost of the material from which the border is made. It is worth noting that simple and affordable models cannot boast of a long service life, so if you want to solve this problem only once, you will have to spend certain funds on this;

Modern borders not only solve the issue of moisture in the gap, but decorate the interior

• The material used for wall decoration also largely determines what a bathtub skirting board should be. Most often acquire a border from similar material. If you used a plastic lining or glass wallpaper to decorate the walls, a plastic skirting board is an ideal solution, acrylic skirting boards are quite suitable for an acrylic bathtub. Ceramic or stone borders are appropriate if the walls of the bathroom are lined with tiles;
• The size of the gap is another decisive factor in favor of a particular material.

A modern and simple solution for sealing is a bathtub skirting board

Whatever the initial data, today you can find a suitable option and arrange the joint between the bathroom and the wall so that it is not only functional, but also beautifully. After all, modern borders are able to not only solve the issue of moisture in the gap, but also support, and sometimes even decorate the interior.

Bath plinth: varieties of materials

In order to make a choice in favor of a particular material, it is recommended to familiarize yourself with all existing options in advance, considering the advantages and disadvantages of each. Briefly consider everything that is presented in the modern building materials market.

Plastic borders. especially popular due to efficiency and resistance to external factors

Plastic border for a bath

Excellent technical characteristics of plastic, its strength and resistance to the effects of various external factors are one of the main advantages of this material indicating in favor of such a choice. With a completely affordable cost, he can also boast of a rather simple installation, which will greatly facilitate your work if you plan to do everything with your own hands. The plastic borders for the bath are represented in a large color variety, so choose an option that will fit your interior is more than simple.

The mount is carried out using a special adhesive or liquid nails. Also on sale you can find self.adhesive plastic plinths for a bath. In order to fix such models, it is enough to remove the protective coating and install the part on the place where it should be located.

The installation of a plastic border for a bath can be carried out independently

There are two installation methods. a skirting board for tiles or on top of it. In the first case, work on the installation of the border is carried out before proceeding with the laying of the tile, and in the second case, after the completion of the aforementioned work.

Ceramic border for a bath

The main competitor of plastic skirting boards is ceramic borders. Differing in a longer operational period, as well as high strength, they won one of the leading places in the modern market. This option is especially well combined with walls, for the decoration of which tiles were used.

When choosing a border, it is important to consider the color and material of the wall decoration and bathtub adjacent to it

Once for this purpose, the same tile was used as for walls, manually chopping pieces of the required size and attaching them in the same way as the tile. However, today manufacturers offer not to spend efforts on measurements and fitting parts, but to purchase a ready.made ceramic battles for a bath. over, to facilitate the installation process, special angular elements are sold, which allow you not to engage in fitting, but immediately fix the finished corner.

Another reason to buy a ceramic plinth for a bath is a long service life that can be measured for decades. However, it should be borne in mind that the period of service directly depends on the quality of styling and, despite the apparent ease, this process requires certain experience and skills. Therefore, if you previously did not deal with such work, then it is better to entrust this to a professional in order to be confident in the result.

Ceramic borders are highly durable and long.term in operation

The advantages and disadvantages of ceramic border

The advantages and disadvantages of ceramic skirting boards:

• Ceramic borders are of great tightness. They almost never pass water;
• If the distance between the wall and the bathroom is quite large and the installation of a plastic profile is impossible, the ceramic skirting board will easily solve this problem. It is recommended to fill the gap with slices of bricks of a suitable size, and then close with a ceramic border;
• Of course, the ceramic border will last you much longer than any plastic panel.

Ceramic borders is a variety of colors and textures and fits perfectly into the interior of the bathroom

• The appearance of the ceramic border is preserved in its original form, which cannot be said about plastic panels, which are often cloudy and covered with a characteristic yellow plaque, which can easily spoil the appearance of the bathroom;
• The chemical composition of the material determines high resistance to the most diverse external factors: temperature changes, deformations for the gap, and so on;
• The assortment of ceramic curbs for a bath will probably impress even the most demanding users. On sale you can find both white and color models, smooth and textured, concave and convex.

Why gaps form and why are sides for the bathroom

It is not always possible to make a perfectly even wall, especially if a relief ceramic tile is used to design the bathroom. In most cases, during the repair, small cracks are formed that occur along the side of the bathroom or sink. The appearance of even a small gap will not only spoil the neat appearance of any room, but will also cause moisture in hard.to.reach areas. Constant penetration of humidity leads to the fact that a fungus begins to multiply in the bathroom, which becomes the cause of the appearance of an unpleasant odor.

The bathroom side is a hermetic strip that is tightly closing the gap, which was formed between the wall and plumbing

Useful advice! Most plumbers focus on the fact that you need to eliminate cracks, the width of which is from 1.5 mm or more. And a corner for the bathroom from leakage allows you to remove gaps up to 6 cm wide.

The border in the bathroom is a continuous hermetic strip or tape, tightly closing the gap formed between the wall and the plumbing device. After installing the structure, the appearance of constant humidity under the bathroom is prevented, thereby the likelihood of the development of mold is reduced. Even if there are rounded corners in the room, as is often found in the layouts of old panel houses, or just crooked surfaces, then after making the curb in the bathroom against the wall, all the shortcomings will be hidden and the room will acquire a finished and tidy appearance.

Sometimes you can find tips on a network where they offer to do without a corner in the bathroom, in this case it is recommended to move the bowl of the plumbing device as close as possible to the wall, and then lay ceramic tiles or tiles so that the lower row of masonry is close on the sort of bathtubs. It is important to understand that this method is suitable only if the option of displacing the device is completely excluded. If for some reason there is a settlement, a sloppy gap will appear on the wall, which will still have to be eliminated.

How to choose the right border for a bath

Other reasons leading to the formation of a gap include a violation of the sequence of facing the room. Many plumbing adhere to the rules that the installation of the bath should be carried out only after the complete completion of the floor leveling, but to the wall cladding with tiles. It is with this sequence of work that the probability of the formation of a gap will be minimal. If you install the installation differently, the probability of forming a large slit increases several times and it is possible to eliminate the defect only after the editing of the border.

The bathroom border is able to eliminate the gap up to 6 cm wide

How to install a curb and how to choose it correctly? Determine the size of the baseboard should be at the stage of repair. The length depends on the specific features of the room and bath:

The width of the side and the procedure for performing work will depend on the size of the gap, which is required to close:

• Narrow gap. up to 3 mm. Before installation, the side is better to first fill the gap with sealant.
• Significant distance-0.3-2.5 cm. In such a situation, the gap is primarily filled with mounting foam, after which the optimal width of the corner per bath is selected.
• Maximum gap-2.5-6 cm. To remove such a gap, you need to tinker. First you need to pour the gap with a concrete solution into a pre.prepared formwork, and then select the tape of the maximum width.

Important! To completely close the gap, the width of the border should be 3 times larger than the gap width. It is precisely this value that will be enough to place 2/3 of the tape on the side and leave the same amount on the wall.

Before installing the side gap up to 3 mm, it is better to first fill in with a sealant

Speaking briefly, for the correct choice of material, you should rely on such criteria:

• Surface decoration material. For example, if the walls are made using PVC panels, then the curb is recommended to choose from the same material.
• Type of bathtub coating. It is obvious that it is better to use an acrylic skirting board on a bath made of acrylic.
• The width and features of the gap configuration. If the gap is significant, it is better to install a plastic border in the form of a corner.
• Dedicated budget for the repair of a bathroom. Thanks to modern technologies, some inexpensive skirting boards from polymers in quality and operational characteristics are not inferior to more expensive options from mineral raw materials.

Bathroom for the bathroom: the main varieties of products

Almost every trading platform offers the buyer a wide selection of skirting boards to the bathroom, each of which is distinguished by its advantages and disadvantages. Regardless of the product version, the following requirements are put forward to it:

• Water resistance. Of course, the main characteristic that should be characteristic of the border.
• Simple installation. It is better when all parts and adhesive mixtures necessary for high.quality installation come to the product.
• Simple care. The corner should be resistant to active detergents and should not be damaged with the slightest mechanical effect.
• Good operational qualities. It is required that the material is not exposed and spread of the spores of fungi and is not deformed after a short period of time.

At the sales points there is a large selection of sides on the bath, and conditionally they can be divided into 2 large groups:

The market offers a large selection of borders for the bathroom, they are divided into hard and self.adhesive

• Tough. Presented in a large assortment, a characteristic feature is the absence of an adhesive layer on the reverse side. When buying goods, you need to consider that for consolidation it will be necessary to use silicone.
• Self.adhesive. Are a flexible tape, on the other side of which an adhesive mixture is applied, which provides the most simple installation.

Useful advice! As for the instructions regarding how to install the curb correctly, most masters will advise using a self.adhesive border only if the gap does not exceed several millimeters. If the gap width is more than 1 cm, it is better to give preference to a solid plinth.

With a significant width of the gap, the installation of a solid baseboard provides longer and more effective protection. But a similar type of curb is established only in the case of a constant, stable position of the bowl. If the bath changes its position at load, it is better to close the inconsistencies using a soft adhesive tape characterized by plasticity.

The main characteristics of the plastic corners for the bathroom

Plastic bathroom skirting boards are made on the basis of polyvinyl chloride. Thanks to this, the installation will be much easier than when buying products from other materials. This type of border is easiest to install without the use of special tools. Another advantage of the installation is the possibility of re.using the product if it is necessary to change the location of the bath. Among the main advantages of buying the Bourgehors of Baths, they highlight:

The plastic corners for the bathroom are made on the basis of polyvinyl chloride

• The ability to resist the appearance and spread of the fungus.
• A large selection of color performances that allows you to purchase a suitable option for any surface type. Various types of sides are able to imitate wooden and tile surfaces.
• Resistance to different genera of mechanical damage. However, even this type of borders is not recommended to be cleaned with strong abrasive means.

An mounted plastic side does not require any special care, and is also universal, because it is easy to choose an option for any material applied for wall decoration. An important advantage for users is the affordable price of goods, which is affected by most buyers.

Important! A significant and almost the only drawback of a plastic skirting board in the bathroom is its short service life and the inability to ensure the desired tightness when deforming.

As for the user characteristics, the editing of the border is carried out using silicone or construction glue, the second name of which is “liquid nails”. Products of various sizes are available for purchase, because there are no certain standards regarding the parameters. All the accessories necessary for installation are included in the kit for the product. This includes side plugs and docking angles designed to decorate internal corner spaces.

The main advantage of the plastic corner for the bathroom is its low cost

For a reliable and high.quality fit to the Plumbering side, some products have rubberized edges. Products are also considered universal, because they can be glued in two ways:

• External. In this case, installation is carried out after laying the tiles on the walls.
• Interior. Installation is performed between the wall and the bathroom for the tile. To make it beautiful, it is better to entrust the attachment to a person with experience. In the absence of skills, it may not be possible to correctly fix the corner for the bathroom under the tile, and after such installation there is a high probability of leaks.

The popularity of PVC sides is also ensured due to the large selection of color performances, various textures and forms. So, if an oval bowl is installed in the bathroom, preference should be given to the curbs, which are characterized by increased elasticity and flexibility. If you want to create maximum tightness, it is better to purchase options with rubberized edges. The main advantage of rubber borders for baths is that they can be used to seal not only baths, but also shells.

It is necessary to install the border made of plastic after the gap between the wall and the bathroom is covered with the help of the sealant. This is recommended to do in order to prevent water under the bowl in the case of peeling off. The most common option is the border for the bathroom made of PVC, because the product has a number of advantages, including:

Pros and cons of ceramic borders

Find a quality product for decorating a gap between the wall and the bathroom is not difficult.

• Resistance to negative factors. The glazed surface does not allow the material to absorb moisture, protects the basis of the effects of aggressive substances.
• Insensitiveness to mechanical influences. The module does not deform, does not lose decorative properties for 25 years.
• Ease of care. The product can be washed by any chemicals. Like tiles, it does not fade, does not deform.
• Attractive appearance. This decor element harmonizes with tiles. There is an opportunity to create any design.

Tiles of borders have disadvantages, which include such moments as:

• High price. This does not allow reducing the cost of repairing a bathroom.
• Fragility. Despite the strength, the material cannot be blocked. When objects fall on the surface, cracks appear in which pathogenic microorganisms accumulate.
• Difficulty in the installation. A special glue is used to glue ceramic elements. It is applied slowly, neatly. To do this, you will have to be patient. After hardening, the glue acquires stiffness, which excludes expansion under the influence of high temperatures. The ceramic border is not suitable for decoration of the gap between the wall and the acrylic bathroom.

Installation of a corner on a new bath

When installing a new bath, the sequence of work and the type of corner used depend on the above factors that determine the subsequent operations.

However, the general procedure for performing work is as follows:

• The purchased bath is extracted from the packaging and its sides are cleaned of dust and dirt, for which detergents and sponge (soft rag) can be used;
• To install the bath, the elements of its fastening are mounted to the floor (legs, frame, podium, etc.D.);
• On the surface of the wall mating with the bathroom, marking is performed corresponding to the height of the side of the floor;
• Further, work is performed depending on the type of skirting board used.

Internal corner

When using a corner for tiles, installation is performed as follows:

• The surface of the wall and the side of the bathtub degrease, the bath is installed close to the surface of the wall.
• A silicone seal is laid in the gap between the wall and the side and the time is given to harden it.
• After hardening the sealant and on the basis of the marking made, cutting and installation of the baseboard are performed.
• The skirting board is attached so that its lower (horizontal) bar falls on the side of the bathtub, and the vertical. on the surface of the wall.
• For fastening to the wall, spacer dowels or other fasteners are used.
• The finishing of the wall is performed, for which tiles, finishing panels or other waterproof material are used.

When using the corner on the tile, work is carried out in the following order:

• The preparation of walls and baths is performed similarly, as when using a corner for tiles.
• The surface of the wall is finished, while the laying of the tile and other elements of the finish, is performed in accordance with the marking (from the upper edge of the bathtub).
• After the wall decoration, the bath is installed and sealing its adjacency to the wall (similarly, as in the above case).
• After the sealant is hardened, the skirting board is cut and with adhesive substances (sealant, mastic, liquid nails, etc.D.) the corner is attached to the wall and horizontally located the edge of the bath.
• When installing the skirting board, shaped parts (corners, connectors and others) are used, fastening is carried out by pressing the fixed element to the covered elements.

Installation of a corner on a new bath

When installing a new bath, the sequence of work and the type of corner used depend on the above factors that determine the subsequent operations.

Installation of a corner on a bath

However, the general procedure for performing work is as follows:

• The purchased bath is extracted from the packaging and its sides are cleaned of dust and dirt, for which detergents and sponge (soft rag) can be used;
• To install the bath, the elements of its fastening are mounted to the floor (legs, frame, podium, etc.D.);
• On the surface of the wall mating with the bathroom, marking is performed corresponding to the height of the side of the floor;
• Further, work is performed depending on the type of skirting board used.

Internal corner

When using a corner for tiles, installation is performed as follows:

• The surface of the wall and the side of the bathtub degrease, the bath is installed close to the surface of the wall.
• A silicone seal is laid in the gap between the wall and the side and the time is given to harden it.
• After hardening the sealant and on the basis of the marking made, cutting and installation of the baseboard are performed.
• The skirting board is attached so that its lower (horizontal) bar falls on the side of the bathtub, and the vertical. on the surface of the wall.
• For fastening to the wall, spacer dowels or other fasteners are used.
• The finishing of the wall is performed, for which tiles, finishing panels or other waterproof material are used.

When using the corner on the tile, work is carried out in the following order:

• The preparation of walls and baths is performed similarly, as when using a corner for tiles.
• The surface of the wall is finished, while the laying of the tile and other elements of the finish, is performed in accordance with the marking (from the upper edge of the bathtub).
• After the wall decoration, the bath is installed and sealing its adjacency to the wall (similarly, as in the above case).
• After the sealant is hardened, the skirting board is cut and with adhesive substances (sealant, mastic, liquid nails, etc.D.) the corner is attached to the wall and horizontally located the edge of the bath.
• When installing the skirting board, shaped parts (corners, connectors and others) are used, fastening is carried out by pressing the fixed element to the covered elements.

External corner

When the external corner installed on the side of the bathtub is used, the key to successful operation in this case will be proper preparation of the surface of the wall at the junction of the bath, as well as the correspondence of the size of the plinth sizes of the bath.

The surface of the wall is cleaned of dust and dirt, after which the outer corner is put on the sort of the bath and glued by means of the adhesive layer to the surface of the wall.

A collapsible corner

When using the collapsed corner, the technology of its installation combines the methods of installing the corner for the tile and on its surface.

Initially, the internal component of the profile of this type is mounted, while the work is performed as in the case of the installation of the internal corner going under the tile.

After that, the second part of the profile is mounted, for this, silicone and a special design is used, connecting both components of the corner into a single whole (“spike-puzz”).

Sloths for installing skirting boards

Whatever the product option is chosen, it is first necessary to prepare the surfaces for their installation.

• The fat film should be removed from the surfaces. To do this, they are wiped with a rag dipped in a solvent or alcohol.
• If the border is re.installed, then the dismantling of the old skirting board is carefully carried out and the surface is cleaned of dirt and glue.
• The mold available under the filmed border should be scattered with a spatula. After that, the surface must be treated with an antiseptic solution.
• The walls and borders of the bathtub after processing with solutions are dried with a hairdryer.
• For better tightness, it is recommended to fill the gaps with an even layer of silicone gel. If the gap is large, it is previously filled with waterproof mounting foam, and after drying it. with a sealant.

Setting a plinth from PVC.

Plastic batteries for a bath are installed on a transparent glue that should quickly grasp.

• Using a conventional hacksaw with small cloves, the desired size of the baseboard is cut off;
• In the corners of the tall, the slice should be done at an angle of forty.five degrees;
• In order not to damage the glue enamel of the bathtub, it is recommended to glue its edges with molar tape;
• A thin layer of glue and dumbbell is immediately pressed on the base of the skirting boat is immediately pressed by one side to the bath, and the other to the wall;
• The gaps formed after installing the curb are filled with sealant;
• plugs and corners are installed that ensure the docking of the baseboard and ennoble its view.

Installation of a ceramic border.

The product is cut using an angular grinder with a diamond disk.

• According to the instructions on the packaging, glue is prepared.
• The skirting board is cut at an angle of forty.five degrees, and its edges on the cut are polished by an emery bar.
• Installation is recommended to start from the corner.
• Glue is applied to the back of the border, and the product is attached as tightly to the joint.
• Excess glue are removed, and the surface is wiped.
• In order to fix the adhesive even more, after drying it, the laid curb should be abundantly watered with water.
• The gaps between the baseboard and the wall are filled with silicone sealant.

Installing a self.adhesive border

The product is a little more expensive than plastic, but for its installation it is not required to purchase additional materials.

• The surface for installing a self.adhesive plinth should be smooth and dry. This is the main condition for the installation of this product.
• A protective strip is removed from the back of the tape.
• The product is applied to the installation site.
• A spatula is used to indicate a right angle.

Thus, we can conclude that the most practical and inexpensive option for a bath is a plastic product. By installing a plastic baseboard, you can get excellent protection from dampness and mold, a beautiful bathroom, and even save.

Description and installation of a plastic bathtub skirting board

During the repair of the bathroom, after installing the bath, many are wondering. how to close the gap between its side and wall? This should be done not so much to decorate the interior as to prevent the fungus from entering the gap and formation. It will reliably protect against water flow and give the bathroom aesthetic type of skirting board, which can be made of different materials.

Plinth for bathtubs and description

recently, the gap between the wall and the bathroom was covered with cement mortar and covered with paint. As a result, moisture did not fall under the bath, but the interior did not decorate at all.

Currently, more elegant options for protection and design are offered in the markets of building materials.

Finishing material varies in the material from which it is made. The most popular panels:

Choosing a plinth for a bath, you should know several requirements that it must comply with. The border should be:

• Absolutely waterproof.
• Resistant to deformation.
• Not prone to decay.
• Resistant to household chemicals that will be used for cleaning.
• Easy to care.

In addition, the baseboard should easily be installed on the bath.

Plastic is moisture resistant and quite inexpensive material, so it is quite suitable for using it in the bathroom.

Plastic skirting boards is a bar whose length can reach two and a half meters.

PVC products are mainly used to mask the joints between the wall and the border of the bath and protect them from water getting. The wall can be finished with PVC panels or ceramic tiles.

• For a decorative function, you should choose a wide skirting board with parameters of thirty.five to forty.five millimeters.
• The optimal width for the curb, which will be installed under the tile. thirty millimeters.
• Pl Incs from PVC in a variety of design are produced. Choosing them for the interior of the bathroom will not be difficult.
• Currently, borders from PVC with rubberized edges are produced, which is an additional protection against leaks.
• Panels are usually sold with a kit of accessories, which includes elements for docking angles and end plugs.
• Installation of plastic products can be done before and after installing the tiles on the wall.
• The flexibility of the plinth from the PVC allows its installation in rounded rooms.
• Over time, plastic may turn yellow, so it is not recommended to choose white borders.

Ceramic products have mechanical strength and high hardness. In addition, they practically do not respond to the external environment and with other substances. Ceramic skirting boards also have all these properties.

• Compared to a plastic product, it is more durable.
• Made in different decorative performance.
• Saves its color.
• The only drawback of ceramic skirting boards is that it can collapse from a strong mechanical effect on it.

Acrylic plinth. In most cases, the product is used for a bath made of acrylic. Its operational properties and installation are similar to the product from PVC.

Products look very impressive, noble and are the most durable.

• The main feature of marble is the variety of it in color and the formation of veins;
• In combination with the bathroom, such a skirting board looks very organic;
• The price of the product is quite high.

This is the simplest and cheapest option for filling the cracks between the wall and the bath of the bath.

• The installation of the product is so light that any.
• Its minus is that such a border will last no more than two years, after which it will have to be replaced.

Sloths for installing skirting boards

Whatever the product option is chosen, it is first necessary to prepare the surfaces for their installation.

• The fat film should be removed from the surfaces. To do this, they are wiped with a rag dipped in a solvent or alcohol.
• If the border is re.installed, then the dismantling of the old skirting board is carefully carried out and the surface is cleaned of dirt and glue.
• The mold available under the filmed border should be scattered with a spatula. After that, the surface must be treated with an antiseptic solution.
• The walls and borders of the bathtub after processing with solutions are dried with a hairdryer.
• For better tightness, it is recommended to fill the gaps with an even layer of silicone gel. If the gap is large, it is previously filled with waterproof mounting foam, and after drying it. with a sealant.

Setting a plinth from PVC.

Plastic batteries for a bath are installed on a transparent glue that should quickly grasp.

• Using a conventional hacksaw with small cloves, the desired size of the baseboard is cut off;
• In the corners of the tall, the slice should be done at an angle of forty.five degrees;
• In order not to damage the glue enamel of the bathtub, it is recommended to glue its edges with molar tape;
• A thin layer of glue and dumbbell is immediately pressed on the base of the skirting boat is immediately pressed by one side to the bath, and the other to the wall;
• The gaps formed after installing the curb are filled with sealant;
• plugs and corners are installed that ensure the docking of the baseboard and ennoble its view.

Installation of a ceramic border.

The product is cut using an angular grinder with a diamond disk.

Features of choosing a plinth for a bathroom

It is necessary to take care of sealing the bathroom. This premises especially suffers from high humidity. It is possible to form a fungus and other adverse phenomena, if you do not use special tools for processing. The baguette allows you to solve most of these shortcomings.

The process of choosing and buying a plinth is quite complicated and takes time. Attention should be paid to the following parameters:

• Price. There are many different models that differ in the price category. There are cheap solutions for several years. If something is required more durable, in this case it is better to pay attention to marble or ceramic elements. They are distinguished by an attractive appearance, ease of care and a long service life.
• Decorative function. There are materials that complement the coating and practically do not differ from it. If you want to decorate the room, you can use various decorative elements.
• Material. For the border, you should use the same material that is used for the main coating of a bath or tile. It looks beautiful, does not catch my eye, and also speaks of the good taste of the owner. This decision remains with you.
• Gap. One of those parameters that speaks in favor of a particular material. Consider the width of the baguette to carefully seal the gap.

If the bathroom skirting board has high quality, all its functions will be preserved throughout the entire service life of the border.

Important! Choose the material in accordance with the requirements of the operation of the premises. The main thing is that you like the final result.

When you seal joints, you will need to use plugs. They eliminate unnecessary gaps in the design. To arrange corners, corner elements are used, which allow us to simplify the butt of elements.

The border must have 100% water resistance to reliably protect the joint from mold, rot, moisture and fungus.

What glue to choose for gluing a plinth

Most often, silicone glue is used. This composition is molded over time. To avoid this, it is recommended to use special disinfectants.

Glue for aquariums can be used as adhesive. it avoids the formation of a fungus or mold.

note! Some sealants are unable to provide high.quality skirting stools. As a result, they begin to move away from the walls. To solve the problem, they use polymer compositions that have the necessary elasticity. Glue only the part that adjacent to the wall.

Features of corners for bathrooms

With proper placement of protective corners, they fully fulfill their function. Their main task is to prevent moisture on the walls and edges of the bath. In some cases, these features may vary. This is often due to the material of manufacture.

Plastic corners for the bathroom

Plastic borders remain in demand in places where there is a constant excess of moisture. The design is usually supplied 2-2.5 m long. As a rule, the device is flat, has no internal gaps. Flexible material makes it possible to clarify the bathrooms of complex configuration.

If holes are provided in the design, then during installation they are closed with special plugs

Special strips withstand temperature changes. In addition, dust does not accumulate on such a surface.

Ceramic corners for the bathroom

This type of borders must be used with caution. Structures do not tolerate a careless relationship. The main features are considered to be durability, attractive appearance and environmental friendliness.

The design of the bathroom with such a border is suitable in the case of any layout of the bathing area

Ceramic products have a sloping shape, so they are very convenient for use. They can be washed by any chemicals.

How to choose a plinth for the bathroom, depending on the place of its location

Without fillets do not do when arranging modern designs. They are the best way to make joints hermetic. However, such models need to be able to choose the right, given the place where they will be mounted.

Ceiling fillets for the bathroom

Ceiling devices are a convenient decorative design. With proper installation, the room becomes finished and concise. They can take various materials as a basis. In particular, they try to use plastic or foam.

They try to use figure wide baguettes in rooms, where there is a defect in joints between the wall and the ceiling

The length of one skirting board does not exceed three meters. The units are flat edges. Corners can be formed with your own hand or using special details.

Floor skirting boards for the bathroom

In the premises of a residential building, you can not do without finishing the interior of details. As for gender, it is the floor version of the plinth that is used here. It is made of wood, plastic or ceramics.

Often the floor skirting boards try to choose to match the walls

Skirting boards for the bathroom on the floor are characterized by increased strength, they can have a smooth shape or sharp corners. Planes sit on special adhesive compounds. They differ in shades, appearance and shape. The assortment has a lot of skirting variations. Therefore, they are very easy to choose for the existing interior.

Border for sealing cracks between the bathroom and the wall

To clog the gap between the bathroom and the wall at home try to use various methods. Someone uses mounting foam, others try to close the hole with a cement mortar. An alternative to these approaches is a plinth sticker. Thanks to a sufficient number of options, you can use any suitable.

We recommend looking at the photo of the most common models.

It is better to choose models with a rubber or silicone edge

How to glue the molding to the bath

Most often, masters advise laying moldings on sealants with silicone. However, any sealant from water darkens and after a couple of years lags behind the wall. For these purposes, it is necessary to use sealants intended for aquariums. Thanks to special additives, they do not darken and are not exposed to fungus and mold. Especially if the composition includes MS-polymers (moment, crystal).

Ceramic border can be glued with an epoxy resin or a special moisture.resistant solution.

If there is no sealant, liquid nails or tile glue are suitable. You can only mount a plinth on a dry, clean and low.fat surface.

Installation of a corner border

To install any type of plastic sides for the bathroom, you will need tools:

• roulette, level;
• knock. a tool for oblique sections;
• rubber and plastic spatula;
• Maslar adhesive tape;
• construction knife;
• sealant, acetone, liquid nails;
• Construction gun.

Before the installation procedure, it is necessary to clean, degrease and dry the surface on which the corner will be mounted. Next, it is necessary to fill all the cracks with a sealant using a construction gun. While the sealant will dry, you can stick the masking tape on the tile and the bathroom around the perimeter. this will protect them from glue hit.

Then it is necessary to apply the glue to the inside of the corner, preferably evenly distributing over the entire surface. Further, the corner is installed on the bath and pressed until the clutch occurs. In the corners of the bathroom, the curb is cut at an angle of 45 degrees, and special plugs are attached at the ends for a pleasant appearance and finishing the canvas. After a day you can use the bathroom and not be afraid of leakage.

After the glue dries, you can proceed to the final stage. covering the joints of the corner border with a transparent sealant.

How to correctly saw off the corner to the bath: instructions step by step with photo

So, you made expensive repairs in the bathroom. The brand new plumbing sparkles with nickelled surfaces, the snow.white bath is neatly framed on all sides with a beautiful tile. Everything seems perfect, but something is still missing. Maybe you forgot to install a special border in places where the bath comes into contact with tiles?

This element affects not only the aesthetic appearance. A similar finish, if everything is done correctly, hermetically closes the cracks between the bathroom and the walls, thereby preventing moisture penetration.

This article is a detailed instructions explaining how to saw off the corner to the bathtub of step by step (with the photo) so that the cut edges are well incorporated with each other without forming unpleasant gaps.

Choose the type of element

To get started, let’s try to understand what kind of finishing corners for the bath are. For all the latitude of the borders, the borders can be divided into four main types. Whatever corner you choose, it will relate to one of the species below.

Plastic corners are light, they can simply process them, you can even cut them with a clerical knife. And they cost cheaper than, for example, ceramic copies. The latter have a high price, and it is more difficult to cut them, but the appearance of such borders justifies these inconvenience with more than.

The corners of the VIP quality are made of marble, granite or other natural material. They are much more expensive than everyone else, quite capricious in processing, but they look very solid and luxurious.

Ribbon borders are glued on top of the tile. You can cut them with any tool.

To understand how to correctly saw off the corner to the bath, it is necessary to decide which option to choose, because each material has its own individual physical properties, such as strength, fragility.

Measure the walls adjacent to the bath

How to saw off and install a corner on a bath? In order to know exactly the total length of the necessary materials that will be needed to finish the bath from all sides, you need to take a roulette. The measuring scale must be applied close to the surface along the lines of contact of the bath and tiles.

We need to measure three sides adjacent to the walls. The resulting numbers must be folded and divided into a standard corner length. It can be recognized in the store in which you are going to purchase materials. The result obtained after division should be rounded.

You can add two or three to the desired number of corners in case, when cutting, something goes wrong. Such a stock is especially useful if you have chosen corners of ceramics or marble as a border for a bath, because when cutting elements without some experience of such work, you can make chips.

All measurements must be made before sawing off the corner to the bath, because, as the proverb says, “measure seven times, cut off once”.

Measure the segments of the desired length

It is equally important to properly measure the corners.

First, select the necessary segments along the length. To do this, you can use roulette, construction line or “centimeter”. If you decide to use the borders of plastic, then you can measure strictly defined distances, because cutting such a material is quite easy. In the case of ceramic or marble corners, you should leave a little more space, that is, add two centimeters to the length of each segment. These reserves will be useful to you so that there is something to seize with the pliers when the excess breaks along the drawn line.

Marks in the right places of the corners can be made by a special construction marker. The marks drawn by him are easily erased by alcohol wipes.

We will finish the corners later, using special tools so that they form a suitable angle of 45 ° or 90 °. Then we will talk about how to saw off the corner to the bath. Photos will help you better understand all the steps of this process.

Mark the cuts of the cuts with the help of

It is important to remember that in the place where two corners will joke, it is necessary to make a slice at an angle of 45 °. If you celebrate by eye. most likely it will not work very carefully. But what tools to use to make the cut even and corresponding to the desired corner?

For these purposes, you can apply a fairly simple tool. If you do not know how to properly saw off the corner to the bath, so that the corners of the cut elements coincide, use the accuracy of the accommodation with construction stupid.

This part is a short bar with a recess in one of the longitudinal faces crossed by grooves, in which you can put a hacksaw cloth. A corner should be invested in the longitudinal seizure. The grooves mentioned above are located at different angles. By putting a hacksaw in the desired groove, you can cut off the corner as accurately as possible.

Using Malkov for Marking angles

Tape is called another measuring tool. In locksmith and carpentry, they are used to mark something at certain angles. Using such a measuring device will help you not make mistakes before sawing off the corner to the bath. The instructions for the use of Malkalka are quite simple, even a novice builder will cope with this.

Malka is a design of two lines connected by a clamp joint. Some tool models have a circular scale of degrees resembling a transporter. Malka is very easy to use. A corner is applied to a more massive ruler, the second bar is allocated to the desired angle and is used as a guideline when applying a mark in the right place.

How to cut a plastic corner

One of the most popular views of the corner is a plastic curb. This is not surprising, because this material is much easier to process than ceramics. It costs too cheaper, it looks great. In addition, stores represent a wide variety of such borders.

type, pros and cons, installation instructions

The article tells how to close any gap formed between the bathroom and the surface of the wall. The types of ceramic borders are described, and their features. It is told how to choose the material suitable for your conditions. It is described how to stick tiles and what is needed to seal the seams and fight pathogenic microbes.

Pros and cons of ceramic borders

The quality of installation is important no less than the quality of the material itself

Choosing a high.quality ceramic border for decorating a bathroom is not difficult due to a wide variety of material. Professional tiles are not advised to fill with plastic corners of the joints between the wall and the bathroom if the walls of the room are finished with tiles.

The positive properties of ceramic options:

• The material does not absorb moisture, the surface covered with glaze does not pass the liquid;
• The strength and resistance to the mechanical influences of these products are a big plus. This allows you to use them for 25 years;
• Immunity to the effects of aggressive detergents. Both tiles and ceramic version are washed with any chemicals;
• In addition to practicality, the curb looks attractive, for such a reason it fits organically into any design.

It is undesirable to fix the joints of the joints with an inexpensive plastic skirting board, since it is difficult to fix it reliably. Plastic products will last less tiles.

• High price;
• Although the ceramic border is strong, but it is fragile. They can not drop heavy objects on them, they can not stand blows. If the material is damaged, cracks are formed, moisture begins to collect in them and pathogenic microflora develops;
• Ceramic borders must be glued to tile glue. For neat and even gluing, you must not rush, have enough time and good patience;
• When the glue sets, it becomes tough, this reduces the possibility of thermal expansion, for such a reason ceramic products cannot be used in rooms with acrylic baths.

Varieties

The gap appears due to uneven tiles, errors in work, wall curvature. The ceramic version will hide this drawback and will become part of the design of the room.

Decorative ceramic border. an element in color, structure and texture is similar to a tile that was made by a bath. Professionals also call it “fingel”, but this name is rarely used.

• Pencil. This ceramic product resembles a rectangular tile, 30 cm long and 3-4 cm wide. It is used in order to close small cracks between the surface of the wall and the bathroom, and as a decorative element for the visual division of the room into zones;

• Angular. This variety is similar to a narrow tile resembling a corner. They are used to close large and medium cracks between the surface of the wall and the bathroom;

• Frieze. This is a special tile for decoration of the surface of the walls, it laid out the first row of the finishing surface above the bathroom. It differs from the usual tile in that its lower cut has an influx that closes the gap between the surface of the wall and the bathroom.

Frisis is rarely used, it can be used exclusively for narrow cracks.

If you could not find a suitable ceramic border, it can be done by dividing the tile into stripes of the desired width, most often 3-4 cm.

• Ribbon. This is a polymer tape, with an adhesive tape on the inside, the adhesive part resembles a double.sided tape. It is glued with a construction hair dryer, with which the filler is heated and installed in place. Without this, it will be difficult to place a hard tape in the right position without gaps;
• Plastic. This is a triangular plastic skirting boat with soft edges. Sometimes it is called “Swallow’s tail”. The gap with this border is covered with “liquid nails”.
• Ceramic. It is made of high.quality clay, which is used in the production of tiles.

The pluses of a plastic and tape border:

• Cheapness;
• Convenience of installation. any master can make;
• Complete resistance to moisture;
• Not afraid of the fungus and mold, is not subjected to rot;
• Withstands temperature changes minus 50-plus 15 degrees.
• Can last no more than 2-3 years;
• For gluing, a flat flat surface is required, otherwise gaps will appear;
• Plastic from hot water after time loses its external attractiveness. it turns yellow, acquires a matte shade;
• Installation on “liquid nails” or sealant short.lived. especially noticeable when using acrylic or metal baths. When a heavy person is plunged into the container filled with water, the bath is deformed, and affects the adhesive compound.

It is profitable to use these borders due to the low cost. it is not difficult to remove exfolved products, and stick a new filler in its place. It is advisable to glue with liquid nails or sanitary sealant containing antiseptic additives.

Right choice

To understand which border is best used, you need to take into account the following parameters.

• Decoration of the premises. The bathroom, which is lined with PVC with panels, requires the use of a border from the same material;
• From which the bath is made. For example, for acrylic baths you need to use products from the same material;
• The size of the gap between the surface of the wall and the bathroom. If the slots are large, then it is advisable to close them with plastic corners;
• How much money can the owner spend.

When choosing a ceramic skirting board, check if there is enough its width to overlap the crack. It is important to choose such a material that its width is more than a gap by 2-3 cm.

Step.by.step instructions for installation in the bathroom

The ceramic version is installed only after laying the tiles and installation of the bath. To work, tile glue, grip for seams, spatula, silicone sealant will be required.

Calculation of the required number of borders

Before buying the material, you need to calculate how much it will be required to block the joints around the perimeter of the bathroom.