How to cut roller blinds to width

Trimming delicate fabrics

You don’t always need to cut off excess fabric. If the curtains are only 10-15 cm long, then it will be easier to simply bend and sew. However, sometimes it is still necessary to shorten the product. To do this, you need to prepare sharp scissors, a ruler (construction tape) and crayon. A straight line is drawn on the fabric, along which it is cut off without lifting the scissors or curtains from the floor. You cannot shorten by weight, otherwise the cut will turn out to be crooked.

Delicate fabrics such as organza or silk cannot always be cut straight. Thin material constantly escapes the scissors. There are 2 methods to shorten the curtain as much as was required initially. This is the pulling of the transverse threads and cuts. the choice of method depends on several factors.

How to cut a roller blind on your own in width

Pulling the cross thread

The second method is recommended when working with simple organza (without embossing) and similar fabrics. It is much easier. you just need to measure the length, make a small incision on the side and pull out any transverse thread. It should be removed carefully so as not to tear. A line is formed (a small gap in the fabric) along which the canvas is cut.

Mix system

A newcomer to the market is the Mix system (sometimes referred to as “bottom-up”). This version of roller blinds differs significantly from its predecessors and, thanks to the original approach, has already gained a lot of fans. The key difference is that, unlike others, the Mix system is installed in any part of the window (most often at the bottom), and not just at the top. In fact, the structure rotates 180 degrees, and the result looks stylish and functional. Installation of roller blinds on a plastic window. The dimensions of the canvas in this case is the distance between the glazing beads. No additional allowances are required.

The design of the roller blind allows you to close the window both from the top and from the bottom

Installation is carried out as follows:

• the fishing line is cut into equal parts;
• all parts are first passed through the upper limiter, after which they are tied into several knots;
• limiters are attached to glazing beads;
• free parts are threaded into the holes of the protective box, after which they are attracted to the lower bar, parallel to fixing the upper bar;
• after the latches on the roller shutter are wrung out, all that remains is to raise the canvas.

Whichever type of roller blind you choose, it’s safe to say that it will look great on the window. Installing a roller blind on a window with your own hands. Of course, the installation of Roman blinds on plastic windows is most often carried out by a specialist, but independent installation is quite a feasible task even for a non-professional.

How to make roller blinds with your own hands

Roller blind on the finished mechanism.

A set for making a curtain includes a roll for winding fabric, fasteners and a mechanism with a cord or chain. Before installation, the plastic shaft should be shortened in accordance with the width of the window and a curtain panel should be fixed on it, which must be specially prepared for this.

• For ease of closing and good tension of the curtain, a special is made on the lower edge of the cloth, into which a rod or stick is inserted for weighting. On a curtain made of double-sided fabric, you just need to bend the bottom edge to the side facing the window and stitch it along the width of the panel. The amount of bend depends on the thickness of the weighting material and is determined individually. When sewing curtains made of fabric with a one-sided pattern, the load can be placed inside a double-layer cloth.
• Fold and smooth the upper cut of the curtain by 1 cm. Stitch one of the Velcro elements along the edge of the fold, lay the 2nd line along its lower edge. Attach another Velcro element to the shaft (roller) from the roller blinds set along the line or groove drawn on it using double-sided tape (Fig. 1).
• According to the instructions attached to the kit, mount the brackets or other fastening parts of the blinds on the window, install the mechanism. Attach the curtain to the shaft and roll it up. Strengthen the shaft to its original place and lower and raise the curtain several times so that it stretches well.

How to make a blind with a bottom shaft?

Figure 2. DIY roller blinds.

If the fabric has a pattern on only one side, the curtain will have to be made of two layers of fabric so that both the face and the wrong side look aesthetically pleasing:

• Fold the material with the right sides (pattern) inward and sew the sides without sewing the top of the resulting bag. Turn the workpiece out onto your face. The bottom of the curtain can be folded over by placing a shaft with the ends protruding outward, as indicated above, or by placing a tube or block inside the bag.
• The top edge can be folded in and stitched 1 mm from the edge, sewn by hand with a blind stitch or bend over the hole so that the shaft can be removed from the inside if necessary.
• On the block that will hold the entire structure, attach one Velcro element with a stapler. Attach the corresponding part at the top of the future curtain, attach the panel to the bar and wrap it with a cloth. Arrange ribbons or cords with a length equal to two lengths of the curtain with the addition of 15-20 cm for the free ends as shown in fig. 3. Reinforce the bar on the brackets.

Figure 3. Layout of the tape.

If the blinds are not planned to be removed too often, then the panel is attached with a stapler to the bar, the tapes are hung and the bar is rigidly fixed in the window opening on self-tapping screws.

Such a curtain will have to be lifted and rolled onto the shaft manually. At the desired height, the raised curtain is fixed with tied ribbons.

You can mechanize a do-it-yourself roller blind like this:

• sew decorative rings or loops on the front side of the panel at the top;
• on the wrong side at the top, fasten the ends of the cords or tapes;
• lower the other ends, go around the lower edge of the curtain, skip, without pulling, into the rings at the top of the canvas;
• connect the free ends of the cords.

To roll up the curtain, you need to pull the connected ends of the cords, while the panel rolls up and rises to the desired height. The cord is fixed on a hook attached to the window. The length of the cord should be slightly longer than 2 times the length of the fully unfolded curtain.

You can decorate roller blinds by placing fabric appliques on the canvas, embroidering or trimming the edges with beautiful braid. An additional means of decoration are ribbons or cords, on which you can make tassels or decorate the ends with pendants.

It is important to remember that the decorative elements should not interfere with the canvas to roll and unfold freely.

How to shorten horizontal blinds?

Horizontal blinds can also be tailored to the desired size. The process will depend on how you need to shorten the blinds: in length or width.

If you need to reduce them in width, then you can simply cut off the excess number of lamellas. This can be done without even removing them from the window. First you need to determine how much shorter you want to make the product. To present this more clearly and not to be mistaken, you can make a mark in any convenient way on the window frame (for example, attach a piece of colored tape at the desired height).

Diagram of horizontal blinds.

After that, you need to bring the blinds into an open horizontal view. Then it is necessary to release the control rope, which is used for adjustment, from the lowest bar from the latches. To do this, remove the plastic fasteners holding the lace from this strip. You can untie the knots, but it will be faster to cut the rope. To keep it from blooming, you can scorch its ends a little. After the fasteners are removed, you need to pull the control rope on both sides of the structure just above the level of the mark that is placed on the window frame.

Now you can neatly remove all the extra planks. In this case, care must be taken that the remaining lamellas do not slip down and do not lose their symmetrical position. The lower bar must be attached to the last lamella and all the others must be passed through it, including through the lowest control rope. The plastic clips must be attached to the ends of the rope as they were originally attached. But before that, you need to stretch part of the ladder, which remained from unnecessary lamellas, into the hole for fastening. Now, if you pull up the retainer and secure it in the hole, the ladder will also be secured. The remaining slats can be removed to the pantry so that you can replace any of those that remain in the blinds.

The process of reducing horizontal blinds in width is quite laborious and requires special tools. To shorten them, you will need, firstly, to reduce the cornice, and secondly, the blinds themselves. To do this, you need a hacksaw for metal and a tool for processing slices.

It will be necessary to collect all the lamellas together, fastening well, and saw off the extra centimeters, and then process their ends. It is quite difficult to shorten such blinds in width by yourself, so it is better in this case, nevertheless, to contact the master.

Doesn’t fit the size. How to cut a roller blind with your own hands?

If you cannot find blinds of suitable dimensions in any way and do not want to contact the master for individual tailoring, as it is very expensive, then you can solve this problem on your own by cutting the roller blinds to the required size.

How to cut roller blinds to the width yourself

Roller blinds are most often cut in order to change the design of the room, to decorate, to adjust them in accordance with the dimensions of the window openings. This is necessary when you change your place of residence. If initially your window had the same dimensions, and then you moved into another apartment and at the same time you do not want to buy new window structures, you need to know how to cut roller blinds in width yourself.

Anyone can do this in the presence of an ordinary tool, which is at hand for every housewife. In order to get started, you first need to measure the size of the window. To do this, follow these steps:

• Hang the fabric on the cornice above the window.
• Spread out the curtain material, let it hang a little, take the final shape.
• Make accurate measurements and write down the information received.

The length can be reduced in size in a matter of minutes. To do this, simply make a double or triple hem and hide up to 20-30 cm of rolled fabric in this way.

We select tools

In order to cut roller blinds in width yourself, you will need the following tools:

• soap or a special pencil for fabric;
• household scissors or a sharp stationery knife;
• needles, threads;
• tape measure.

If the curtains are too wide, which goes beyond the size of the window, you need to narrow them. Initially, you need to unfold the canvas, after removing the plugs. Please note that the rolls are equipped with special weights, which must also be removed and cut to fit the new window.

Step by step guide

Use soap and a tape measure to mark the curtain fabric accordingly. Before you cut the roller blinds shaft and bring it to the required length, you need to measure the width of the window, stepping back 2-3 cm from the length of the bracket.

Then you need to install the plugs and cut off the excess part of the rail, which in the end should be equal to the length of the shaft.

The curtains are also marked with soap and a measuring tape. With a sharp clerical knife or ordinary household scissors, the curtain is cut to the width of the bottom of the rail.

Then the material is attached to the shaft. To do this, it must be tightly wound, having previously glued a protective tape with a self-adhesive base. The canvas must be wound carefully and adhere to a strictly horizontal position in relation to the shaft. Avoid the slightest distortions, as in this case all the work will be done in vain.

Fold 5 cm of the blade so that a fold is formed where the shaft with the glued tape will be installed. Do not indent too much, as in this case the shaft will slip and will not be able to firmly lock in the desired position.

Then you need to roll it along the top of the curtain and roll it 3/4 of the length. Install the bottom rail into the hole on the shade. Insert the bracket into the very end of the control mechanism, then insert the other end in the same way. Upon completion of the work, all the parts that secure the system must be assembled, and the roller blind, shortened in width, must be hung in the place designated for it.

As you can see, it will not be difficult to cut the roller blinds to the width yourself. Here the main thing is care and diligence, as well as an hour of free time and the availability of the necessary working tools at hand.

How to cut a roller blind with your own hands?

Roller blinds. one of the most common design options for a window opening. They serve both decorative and practical functions. This compact and stylish sun protection system fits perfectly into almost any room, reliably protects from the sun’s rays, easy to use, easy to operate.

Blinds are a construction of fabric, a rotating shaft and a special mechanism that winds the fabric on a roller. Unlike blinds, they have a solid canvas, and there are no gaps, due to which, when the curtains are lowered, complete darkness in the room is ensured. Compared to the usual curtains, roller blinds are more compact, weigh less, can be rolled up, are easier to clean, since due to special impregnations they do not collect dust and are less dirty.

Doesn’t fit the size. How to cut a roller blind with your own hands?

If you cannot find blinds of suitable dimensions in any way and do not want to contact the master for individual tailoring, as it is very expensive, then you can solve this problem on your own by cutting the roller blinds to the required size.

Types and sizes of roller blinds

Manufacturers offer a huge range of roller blinds, among which you can choose products of any size and for any window. But still, sometimes there are situations when the roller blinds offered by the seller do not have the right size for your windows. This usually happens if windows of non-standard sizes were laid in the building project, or the dimensional grid of the roller blinds you liked is limited and does not contain a model suitable for you.

In this case, there are two ways out of the situation:

• Order custom tailoring of roller blinds. The most convenient solution to the problem. With minimal effort on your part and without any hassle, you will get roller blinds that will fully meet your expectations and dimensions of the window opening. But this method has a significant drawback. high cost of the finished product.
• Buy a sun protection system as close as possible to the desired size, but slightly larger than it, and cut the roller blind yourself. Having decided to do this, you will need to make some effort and spend a little personal time, but the curtains will cost you inexpensively.

The following types of roller blinds are on sale:

How to Cut Down a Roller Shade

Their feature. an open shaft that is not protected by anything. Such blinds are inexpensive, take up little space, and can be mounted above a window opening or on each window sash. Their maximum web width is 1.8 m, height. 2 m.

Roller blinds of this type are equipped with a plastic box that hides the rotating shaft and protects it and the wound fabric from dirt and accidental damage. Another difference between them. small size. The width of the web starts from 0.7 m, the length does not exceed 2.2 m.

Available in lengths up to 4.5 m and widths up to 3.5 m, these roller blinds are perfect for large window openings such as panoramic windows or wide windows in office buildings.

Roof roller blinds are designed to be installed on sloped windows. For a snug fit to them, they are specially equipped with side guides that hold the canvas along the window sashes. Their height. no more than 2 m, width. not less than 0.7 m.

How to shorten the length

Most often, adjustment of roller blinds along the length is not required, since it is enough just not to unwind the canvas to its full length. But if you are a perfectionist and it is extremely important for you that the blinds are of the right size, then follow these instructions:

• Hang the curtains, lower the canvas, wait for it to fully unfold and lie down neatly, then take measurements.
• Mark where you want to crop the canvas.
• Remove roller blinds, spread them out on a horizontal surface.
• Remove the weight from the bottom edge.
• Add an allowance of 40-50 mm to the measured length to create a new “” for the weight.
• Cut the fabric.
• Place a canvas underneath the curtain and sew a “” for the weighting agent, insert it.
• Hang the curtain on the window.

If the length of the “excess” fabric is not too long, then trimming can be dispensed with. It is enough to make a double fold of the fabric, with which you can hide up to 30 cm of fabric. This option for shortening the roller blind is much easier and faster.

How to cut the roller blind to the width

Cutting roller blinds in width is more difficult and requires more care. Preliminary preparation and measurement is done in the same way as described above. After all the measurements are made and the fabric is marked, you can start adjusting the canvas to the desired size. The scheme of work is as follows:

• Lay out the curtains on a flat surface, disassemble into components (take out the shaft and weighting agent) and unfold the fabric.
• Cut the shaft to the required width. Please note that its width should be 8-10 mm wider than the width of the canvas. It is better to cut with a hacksaw. After trimming the edges, be sure to sandpaper or file so that there are no chipping on which the fabric can catch.
• Cut off the weighting agent (it should be 10-15 mm narrower than the roller blinds).
• Assemble the curtain back into a single structure and hang it on the window.

It should be remembered that cutting the roller blinds will immediately void the warranty on them. Therefore, it is worth starting this operation if there are no other options anymore or the guarantee is not too important for you.

Determine which side of the curtain the control chain will be

Decide on which side. right or left. the roller shade control chain should be located. Mark up the curtain and attach the brackets to the window frame or window opening.

The control mechanism is usually located on the side of the bracket with a hexagonal lug or shaft with a hexagonal socket. Be sure to check this first, as the configuration is vendor specific.

How to cut roller blinds to the width yourself

Roller blinds are most often cut in order to change the design of the room, to decorate, to adjust them in accordance with the dimensions of the window openings. This is necessary when you change your place of residence.

If initially your window had the same dimensions, and then you moved into another apartment and at the same time you do not want to buy new window structures, you need to know how to cut roller blinds in width yourself.

Anyone can do this in the presence of an ordinary tool, which is at hand for every housewife. In order to get started, you first need to measure the size of the window. To do this, follow these steps:

• Hang the fabric on the cornice above the window.
• Spread out the curtain material, let it hang a little, take the final shape.
• Make accurate measurements and write down the information received.

to the content

How to cut the roller blind to the width

Cutting roller blinds in width is more difficult and requires more care. Preliminary preparation and measurement is done in the same way as described above. After all measurements are made and the fabric is marked, you can proceed to adjusting the canvas to the desired size. The scheme of work is as follows:

• Lay out the curtains on a flat surface, disassemble into components (take out the shaft and weighting agent) and unfold the fabric.
• Cut the shaft to the required width. Please note that its width should be 8-10 mm wider than the width of the canvas. It is better to cut with a hacksaw. After trimming the edges, be sure to sandpaper or file so that there are no chipping on which the fabric can catch.
• Assemble the curtain back into a single structure and hang it on the window.

It should be remembered that cutting the roller blinds will immediately void the warranty on them. Therefore, it is worth starting this operation if there are no other options anymore or the guarantee is not too important for you.

Types and sizes of roller blinds

Manufacturers offer a huge range of roller blinds, among which you can choose products of any size and for any window. But still, sometimes there are situations when the roller blinds offered by the seller do not have the right size for your windows.

This usually happens if windows of non-standard sizes were laid in the building project, or the dimensional grid of the roller blinds you liked is limited and does not contain a model suitable for you.

• Step-by-step instructions for creating do-it-yourself Japanese curtains
• Photo of the interior of the kitchen and bedroom with Japanese curtains
• Electric drive for curtains
• Photo of interior design 2020 with curtains
• Photo of a living room with panoramic windows
• Photo of the living room interior with curtains on bay windows
• Kyarniz for beveled windows

In this case, there are two ways out of the situation:

• Order custom tailoring of roller blinds. The most convenient solution to the problem. With minimal effort on your part and without any hassle, you will get roller blinds that will fully meet your expectations and dimensions of the window opening. But this method has a significant drawback. the high cost of the finished product.
• Buy a sun protection system as close as possible to the desired size, but slightly larger than it, and cut the roller blind yourself. Having decided to do this, you will need to make some effort and spend a little personal time, but the curtains will cost you inexpensively.

The following types of roller blinds are on sale:

Their feature is an open shaft, which is not protected by anything. Such blinds are inexpensive, take up little space, and can be mounted above a window opening or on each window sash. Their maximum web width is 1.8 m, height. 2 m.

Roller blinds of this type are equipped with a plastic box that hides the rotating shaft and protects it and the wound fabric from dirt and accidental damage. Another difference is their small size. The width of the web starts from 0.7 m, the length does not exceed 2.2 m.

Available in lengths up to 4.5 m and widths up to 3.5 m, these roller blinds are perfect for large window openings such as panoramic windows or wide windows in office buildings.

Roof roller blinds are designed to be installed on sloped windows. For a snug fit to them, they are specially equipped with side guides that hold the canvas along the window sashes. Their height. no more than 2 m, width. no less than 0.7 m.

Size doesn’t matter

Unlike traditional curtains, they are attached directly to the frame or top slope. The canvas tightly covers the glass, saves from the scorching sun, prying eyes. If desired, the roller blind can be hung over open cabinet shelves, doorway.

Manufacturers offer a variety of models. The format of standard roller blinds. 200×180 cm, large. up to 350×4.5 m.

They are fixed on the upper slope or higher on the wall. Mini cassette long. 2.2 m, and narrow, minimum width 0.7 m.

On the sides they are mounted guides for the canvas. In such structures, the canvas does not sag.

Spring-loaded dormers close automatically.

Shortening in width

Often, roller blinds have a large width that does not fit the size of the window. To solve this problem, it is enough to bring the canvas to the unfolded position, for this, plugs are removed from the shafts.

In addition, the rolls are equipped with special weights, they also need to be removed. Then, using a pencil and a ruler, markings are applied to the fabric, and an undercut of excess edges is made with a clerical knife or scissors.

The upper tube is removed so that a small margin of 6-8 cm remains.

As for the weighting agent, it is also cut by a few centimeters. At the end of the work, all fasteners are assembled into a single system, and the canvas is slowly wound onto the shaft. Then the cropped roller blinds can be hung.

For information on how to cut a roller blind with your own hands, see the next video.

Step by step guide

Use soap and a tape measure to mark the curtain fabric accordingly. Before you cut the roller blinds shaft and bring it to the required length, you need to measure the width of the window, stepping back 2-3 cm from the length of the bracket.

Then you need to install the plugs and cut off the excess part of the rail, which in the end should be equal to the length of the shaft.

The curtains are also marked with soap and a measuring tape. With a sharp clerical knife or ordinary household scissors, the curtain is cut to the width of the bottom of the rail.

Then the material is attached to the shaft. To do this, it must be tightly wound, having previously glued a protective tape with a self-adhesive base. The canvas must be wound carefully and adhere to a strictly horizontal position in relation to the shaft. Avoid the slightest distortions, as in this case all the work will be done in vain.

Fold 5 cm of the blade so that a fold is formed where the shaft with the glued tape will be installed. Do not indent too much, as in this case the shaft will slip and will not be able to firmly lock in the desired position.

Modifying Pre-made Roller Blinds to fit Odd-Sized Windows

Then you need to roll it along the top of the curtain and roll it 3/4 of the length. Install the lower rail into the hole on the curtain.

Insert the bracket into the very end of the control mechanism, then insert the other end in the same way. Upon completion of the work, all the parts that secure the system must be assembled, and the roller blind, shortened in width, must be hung in the place designated for it.

As you can see, it will not be difficult to cut the roller blinds to the width yourself. Here the main thing is care and diligence, as well as an hour of free time and the availability of the necessary working tools at hand.

How to properly shorten roller blinds in height and width

Roller shutters with an open block-out system and a bottom weighting device are the simplest in design. They are easily adjusted, they are easy to subtract according to the standard dimensions of window openings in length and width. If the canvases are suitable for the interior design, colors, but wider or longer, you can safely purchase them.

Any hostess can shorten the rolled canvases; this does not require special skills. How to cut a roller blind according to the format is described below in detail.

Fitting doesn’t take a lot of time. If the curtains are not very long, some simply do not completely unwind them, leaving part of the fabric on the roller.

But it is better to immediately adjust the soft blinds to the size of the window openings. Shortened roller blinds are more convenient to operate.

They fit tighter to the frame, do not hang down on the windowsill.

Methods: how to shorten tulle without trimming

How to shorten the curtains correctly without cutting the edge?

This may be required:

• To maintain the integrity of the canvas;
• To avoid crumbling the edge;
• If in the future it is planned to dissolve the material or move it to a new place.

To shorten long curtains, you need to position them in the usual place where they will be used. Then you need to turn the material to the desired length and sew along the edge with loose stitches, while not fixing the end of the seam located at the bottom. The bottom corner should be slightly rounded.

All this is done along the edges of the fabric and in the middle. The middle seam should be 20 cm longer than the side seam. Once all the seams are ready, you need to pull each of them by the threads located at the top, which will allow you to make original folds. Both manual sewing and machine sewing are perfect for this procedure.

Methods: how to trim filament curtains

No less popular, unlike conventional curtains, roller and thread. The second type has recently become very popular due to the type of product. The curtains themselves look very original, they are sold in a large assortment and, most importantly, there is an opportunity to use them for absolutely any room. To trim the muslin or, in other words, curtains in which there are large quantities of threads, you do not need to go to an expensive atelier, since there are more affordable and cheaper ways to shorten.

Methods:

• Performing an undercut in a horizontal view is categorically undesirable, since the threads will get confused, and the undercut will not turn out even at all, which will significantly spoil the look of the curtains.
• The curtains are hung at their location after purchase and washing for 3 days, which is enough to straighten them. This way they will all be vertical and parallel to each other.
• As soon as the flatness of the canvas is checked, you can make an undercut, for which the most ordinary fabric scissors are suitable.
• If the curtains are made of quality material, then no additional processing is required.
• Scissors should be sharpened so as not to jam the threads.

How to trim roller blind to size Install video – with Inspire DIY

There is a simpler and more creative option and this is tying knots on the threads. Thus, they will not get confused and remain in perfect condition for a long time.

How to cut the tulle straight

Cutting the tulle exactly is not as easy as it might seem at first glance, since various defects can occur during the cutting process, which directly depends on the quality of the material. For example, there may be the following nuances: arrows, both vertical and horizontal, the fabric may begin to crumble, and an illiterately cut fabric will have an uneven edge.

There are several techniques you can use to trim tulle to width:

• Moscow;
• Traditional;
• With an oblique inlay.

It is important to remember that tulle is a fabric with maximum subtlety and fragility, and therefore it is categorically undesirable to carry out a zigzag stitch and overlock, which will simply ruin it. It is worth noting that the most optimal option for hemming tulle is a seam hem, which is suitable for such a fabric.

Depending on the type of fabric, the width of the hem is chosen: if it is a tulle-mesh, then the fold will be only 1 cm, nylon and organza are folded up by 3 cm.

Bias binding is considered to be an excellent choice for creating original material side appearances, especially when contrast is required. As for the color of the bias inlay, it is quite possible to choose a shade in accordance with the tone of the fabric or contrasting with it. It is best if the tone of the bias inlay is combined with at least one of the tones present in the interior. It is not at all difficult to cope with an oblique inlay, since it was created specifically for sewing tulle mesh or embroidered material with your own hands. With its help, folds are formed and create an elegant drapery.

For sewing the Moscow seam, you can use a regular sewing foot. In other words, it is required to make the smallest possible hem and stitch it along the edge. The peculiarity of the method is that it does not take too much time and special preparation, only a sewing machine is needed.

Ideas: how to shorten curtains curly

Different housewives have different tricks on how to cut or hem the curtains, and the choice of method depends on: the width and length of the canvas, the type of material and the experience of the needlewoman. It is worth noting that the cut of curtains must not always be even, since curly edges have become very popular lately. You shouldn’t think at all that only a professional seamstress can make such a decorative undercut, since it is available even to not too experienced needlewomen, subject to the recommendations from specialists of the highest category.

Recommendations:

• You need to hang the curtains in their place of permanent residence for several days, and preferably after washing. To hang curtains, you can use a braid, a border or a special tape that is sewn to the top edge.
• After a few days, the material will straighten under its own weight and will be perfectly flat.
• Next, using thick paper and scissors, stencils should be made. A cardboard box is suitable for this. The choice of the line depends solely on personal preference or design idea.
• The stencil is applied to the curtains, for which it is better to use additional help.
• Excess length is neatly trimmed.

What to do with the cut edge and how exactly to process it so that it does not crumble? There are several methods by which serious consequences can be avoided. Previously, to fix the edge of materials such as tulle and organza, they used a lighter, or a candle, with which the edge was singed.

It is advisable to first test the method on a piece of fabric in order to avoid inflammation and damage to the canvas.

An acceptable and safer option is to tint the edge of the canvas with nail polish without color. It will not allow the fabric to unravel, and will also persist even after washing the material. Tucking and sewing the edge or sewing on a bias tape is considered the best option. So the canvas will be beautiful and retain its aesthetics. Depending on the type of canvas, you need to select and cut methods.

How to shorten curtains without trimming: 3 techniques

Trimming or turning curtains may be required if you want to change the interior, remove the edge of the fabric that has lost its proper appearance during operation, and more. There are many options to carry out this process, but it all depends solely on: personal preferences, the availability of inventory at hand, free time, the type of material and what kind of edge you need to make, for example, curly or even.

How to cut roller blinds to width

All methods of undercutting and shortening are simple and do not require additional investments. This simplifies the process of home furnishing with original interior details.