How To Line The Trimmer

Filling the line into the trimmer The line feed system from the trimmer is manual, semi-automatic and automatic. Here is an example of how to thread the line into the trimmer (Trimmer BOSCH Art 30).

Material you can see

A little advice. Try not to let the line come into contact with hard objects when cutting. With this contact, the line will be cut. And since in this trimmer the line is not fed automatically, then every time you have to stop work, remove the reel and release the line again.

In addition to the standard lawn line, my trimmer has a thick line for cutting rough weeds. It has the shape of a pigtail, i.E. Three lines are tightly intertwined. This line has its own spool.

Thick line

It is stored at the top of the trimmer body.

What is a trimmer?

This equipment is based on the following elements:

• A motor whose main function is to rotate the cutting head at the end of the rod;
• The head itself, consisting of a coil, on which either a fishing line or a knife can be wound;
• Knives or fishing line rotating at high speed, which are the main cutting part of the device, how to load the fishing line into the trimmer will go a little further.

An electric device is inferior in its power to a gasoline one, so it is ideal for working on a standard plot of land that is adjacent to a house with source of electrical energy. The main positive aspects of such equipment are the absence of noise during operation, light weight, ease of use and, of course, environmental friendliness.

As for gasoline trimmers, such equipment, of course, is more mobile, so it can be safely transported from place to place and get rid of annoying vegetation in any area. There is no need to use electricity here, which has a positive effect on the functionality of such an apparatus. The cutting attachments can be changed, working with weeds of a wide variety of types.

One of the most common attachments is the fishing line, so you should dwell on this element in more detail.

Types of trimmer line

As a rule, line separation is based on different sample diameters, which can vary from 1.2 to 4 mm. The most commonly used material is a material with a thickness of 2 mm, but in no case should we forget that the choice should depend primarily on the trimmer model.

There is one main rule here: the more power the apparatus has, the thicker the line should be.

This element can also differ in the type of its section. So, it can be round (suitable for cutting plain grass) or square (for mowing soft green cover), sharp edges (tall grass), or be equipped with notches ideal for thin grass in diameter.

Do not forget that with the help of a fishing line it is allowed to mow only grass, and for other, coarser vegetation, it is imperative to use knives.

Next, you should take a closer look at the process of how to insert the line into the trimmer correctly. Indeed, it is with this procedure that many consumers often have difficulties.

How do I fit the line into the trimmer? Operating tips

The trimmer is an excellent modern device designed for mowing unnecessary grass, and its main advantage is that this technique can be used in those places where an ordinary lawn mower will simply not be able to reach due to its massiveness. It is necessary to understand in more detail what trimmers are, and how to choose the best option for a particular summer cottage.

How to quickly remove the coil from the tool

Before the thread is wound on a bobbin, it must be removed. Over, the methods of removal depend on the characteristics of the instrument. On trimmers with a motor near the ground, the reel has two side buttons, when pressed, part of the body is separated along with a device for winding the thread.

On tools with a bent rod, the lamb on the device is moved counterclockwise; having disconnected it, remove both the bobbin and the spring inside it. On trimmers with a straight bar, fix it with a screwdriver, rotate it clockwise and remove it. Then the device is disassembled either by means of latches, or by moving its parts in different directions. The spring is removed from the coil.

How to tuck the line into the trimmer so that working with it does not get tired

Many summer residents use a trimmer. A scythe with an electric or gasoline engine to combat weeds. It is convenient when working in hard-to-reach places for a lawn mower: near fences, flower beds, houses, in a garden on narrow aisles, and can cut small branches. The main element of this miracle technique is an ordinary fishing line wound on a reel. The device is simple, but the cutting part wears out quickly and requires replacement. And the question of how to fill the line in the trimmer worries many owners of summer cottages.

Briefly about the line

Taking into account the models of the tool, the thickness of the line is 1.2-4 mm. There are such configurations:

• Round. The most durable;
• Curly. For soft grass;
• Twisted or serrated. For thin grass;
• Professional, not suitable for all instrument models.

When changing the cutting thread, you need to choose the one that suits your trimmer type. Preference should be given to specialized. Before tucking the line into the trimmer spool, it is better to soak it in water for half an hour. Then it will become more elastic and stronger.

How to tuck the line into the trimmer

You don’t have to work on site for hours on end to mow and tidy up your lawn. With any amount of work, such a device as a trimmer can quickly cope with it. This type of technique can cut grass of any length and density, it all depends on the model chosen. In order for the unit to fully work and perform its main function, you need to refuel the line, otherwise the trimmer will not be able to complete the task.

Line selection

First of all, you will need to choose the correct line. You shouldn’t do it “at random”, as it all depends on the unit model. Pay attention to indicators such as the diameter of the thread, as well as its cross section. You can find information about the diameter in the instructions for the trimmer. The second indicator (section) depends on what kind of work you are going to perform. If this is a soft young grass, a round one is suitable, if it is hard. Choose a square or 5-sided section.

How much line do you need?

For normal operation of the trimmer, 3-4 meters of material is enough. The length of the thread depends on the dimensions of the spool. The larger it is, the longer the line.

If your trimmer has a reel with not one, but two cutting elements, unwind the required amount of fishing line and thread the thread through the hole, the fishing line should be divided into 2 parts equal in length. Then start winding 2 pieces at the same time. When almost all of the line is wound, leave short ends and clamp them in the grooves. This method is suitable for a single groove spool.

If the device has not one, but two grooves, you need to insert the fishing line in a different way. Fold the cut thread in half, at the end you will have a loop. You need to insert this end into the groove, it is located between the two grooves. Each groove has one end. Assemble the coil in the same way as in the previous case.

How to wind the line on the trimmer correctly

A garden trimmer is a useful tool that makes life much easier for any gardener or private home owner. The grass just rushes in the summer, especially after the rains, so you can’t go without it. But over time, sooner or later, the line in it will end, and it will be necessary to insert a replaceable skein of new line. Some summer residents get stumped. How to do it yourself? So our article will help them.

Changing the line on the trimmer

This article will tell you how to change the line on a trimmer. For some people, this job may not be easy. But the step-by-step instructions that are available here will help you in this matter.

So the first thing to do is remove the gear cover. We combine the hole on the side of the curly lower washer and the axial recess, insert a screwdriver to fix the shaft from scrolling. Now unscrew the nozzle. The thread on the shaft, as a rule, has a reverse thread, take this into account when unscrewing.

Next, disassembly of the nozzle follows. There, the cover is fixed with latches through the holes. So you just need to push these clips into the holes and the cover will come off. If the attachment has an automatic / semi-automatic line feeding mode, it means that there is a spring inside, which can simply fly out when the cover is opened, be prepared for this. We lay out all the removed parts neatly in order.

Now it’s time to take the line and unwind 5 meters from it, cut off this piece. Pay attention to its thickness, do not wind a line of greater thickness on the unit than specified in the manual for the tool. Otherwise, there will be an increased load on the engine and a higher fuel consumption during operation. We bend the measured line in half to find the middle and get a loop.

There are a couple of notches in the middle of the coil, sometimes they are not notches, but holes located opposite each other. We cling to one of the grooves with a loop and wind the fishing line counterclockwise. If the reel has 2 compartments, then we wind each end of the line on them separately. Leave the last 15-20 cm free and clamp them while in the recesses of the coil.

We assemble the device again, pull the free ends of the fishing line into the holes on the body. We put on the lid, snapping the latches into their grooves. Now you can pull out those loose ends of the line.

It remains only to attach the working node in place, as in the first paragraph. Do not forget to reverse rotation on screwing.

Now you can learn how to wind the line around the trimmer. Actually, the whole process was detailed above. No time-consuming operations requiring the presence of specialists. Your lawn mower is ready for use again.

What types of woods are there

The most common type of line, which is suitable for almost all types of reels. Round cord. This is an ordinary fishing line, suitable for cutting succulent grass, but it will be much more difficult to cut dead wood with it, and even more so it will not cope with shrubs.

As a rule, the diameter that can be used to cut young grass does not exceed 1.6 mm. The thicker the thread, the more coarse grass it is able to overcome.

There are fishing lines with sharp edges in the form of an asterisk or a square, this option is more adapted to mowing dry grass precisely due to the existing sharp edges, but its disadvantage is greater wear and is inferior in strength to a round cord.

There are fishing lines with improved aerodynamics with characteristic dents, scales and notches, such a product makes less noise, but it is used only on lawn mowers, since it is difficult for such a thread to come out of the reel, it is used most often with discs into which segments are inserted. The disadvantage of such a product is its fragility.

Most often in gasoline trimmers with an engine with an output of more than 1.5 hp. Use cords with a metal cable inside.

This thread is ideal for cutting dry grass and small bushes. The presence of a core has a positive effect on the wear resistance of this material.

The disadvantage of such a cord is its price, which is significantly higher than the listed opponents.

How to change the line in the trimmer and which one is better to choose

Since we considered the choice of a trimmer in the previous article, today we will tell you how to properly fill the trimmer with fishing line, and which one is better to choose based on the working conditions.

After you bought a trimmer and began to actively use it, sooner or later the question of replacing the fishing line will arise, since this is the most wearing element in the tool, then intensive use of the trimmer will lead to frequent replacement of consumables.

How to remove or tuck the line into the trimmer

It will take about 10-15 minutes to wind the line. What is a trimmer coil? Plastic body with a cassette inside, which has a special hook for easy winding of the fishing line.

Almost all trimmer reels have a similar fastening principle, this is a central screw-button, when pressed, it becomes possible to pull out the line of the required length. The photo below shows a few examples of different trimmer spools.

The bobbins of the trimmers, the motor of which is located near the ground, have a different attachment to the axis of rotation, they have two buttons on the spool located on the sides that need to be wrung out, otherwise the replacement of the thread is no different from other cassettes.

The principle of correct winding of the fishing line is similar in all of the above cases, therefore, for example, consider the standard version with two antennae.

To remove the spool with the fishing line, you need to unscrew the screw located in the center, but note that the thread is left there, so you will have to turn it clockwise, this was done on purpose so that during operation it does not open under the influence of centrifugal force.

Next, using a screwdriver, disassemble the head and remove the spool onto which the fishing line is directly wound.

Having measured the required length and folded in half, you need to tuck the line into the spool, eventually bringing its ends opposite each other (for this there are special slots for fixing)

After that, it is necessary to assemble the head in the reverse order, threading the ends of the cord into two corresponding holes.

If you have doubts or it is not entirely clear how to load the line on the trimmer, we recommend that you look at: how to properly wind the line into the lawn mower.

In this, step by step, the instructor will open the trimmer head, measure the required amount of line, usually from two to four meters, and demonstrate assembly and installation on the trimmer.

Than 200 types of trimmers in one place at the lowest prices. Click and watch

Now, having removed and disassembled the coil, we proceed, in fact, to winding.

How to properly wind the line on the trimmer spool

Many, having worked out the factory line on a recently purchased trimmer, try to wind a new one, but cannot, because they do not know how to properly wind the line on the trimmer spool (bobbin). It seems that there is an instruction, but it still does not work. Let’s try to deal with this issue in this article.

So, in order to wind the line, you first need to remove the coil from the trimmer. This will be more convenient. Removal method will depend on the type of trimmer.

Removing the coil from the trimmer

On small, bottom motor electric trimmers (when operating near the ground), the reel usually has two buttons on the sides. Click on them and disconnect one half of the coil body from the second, which remains on the trimmer. Together with the first half, the inner part is also taken out, on which the fishing line is directly wound. When disassembling, be careful: there is a spring inside that can fly out and get lost.

On electric and gasoline trimmers with a curved bar (there is still no way to put a knife on such trimmers), you need to wrap the coil body itself with one hand, and with the other hand you need to start rotating the lamb on it counterclockwise. It is he who attaches the coil to the trimmer bar. Having unscrewed the lamb, carefully remove the entire coil, trying not to lose the spring inside.

On electric and gasoline trimmers with a straight bar and a gearbox at its end (on such trimmers, in addition to the fishing line, you can also install a knife), we look for a hole under the coil, insert, for example, a screwdriver into it, quietly rotate the coil until the screwdriver crawls even deeper, and the coil will lock. Now we turn the whole coil clockwise (since the thread is left-handed) and remove it from the trimmer. Then we disassemble the coil. It can be assembled with latches or twisted with a lamb. If the coil is latched, then press on the sides on the base of the latches so that they bend and release one half of the coil body from the other. We just unscrew the lamb. There may also be a third type of connection of two halves of such a coil: with it, you need to grab the lower part with one hand, and the upper part with the other, and start turning them in opposite directions. When disassembling such a coil, you must also make sure that the spring inside is not lost.