How To Make A Cultivator For A Tiller

Grousers for a homemade motor-cultivator

Our cultivator has to drive somehow. Select the wheels you want. Remember that small wheels will get stuck in the ground and interfere with your work. Too large wheels will be difficult for a homemade cultivator to turn. The selected wheels are fixed on steel corners, which are placed on the gear housing. Attaching the wheels to your homemade gear is not all. Attach the lugs to the wheels. With the help of them, the cultivator will better bite into the ground.

Take car springs or just corners and cut out the hooks of the desired diameter from them. For maximum effect, set the hook angle to 120 °.

When you finish the work with the connection of all the parts, you can use the do-it-yourself motor-cultivator for several years. If you want the machine to simply smash the whole earth into large pieces, you will need to go with it quickly. The lower speed of the passage grinds the earth into the smallest particles. it all depends on the speed of work with the cultivator. Before using it, lubricate the mechanism shaft with oil so that the homemade product will last longer without breakdowns.

By the same principle, you can also take an engine from a washing machine for a home-made cultivator. Disassemble the child’s bike and fit the sprockets and bicycle chain to your unit. As a result, you will get such a self-made electric cultivator. True, if you decide to make this unit with your own hands, keep in mind that the wire will constantly get tangled under your feet and interfere. Due to the fact that the power supply of the mechanism depends on the network and the cable, you will not go further than its length will allow.

How to make a cultivator with your own hands: simpler options

There is such a cultivator. “Nimble kid”. Let’s see how you can make one at home.
Take the wooden axle. It will become the connector for the rest of the parts. On this axis it is necessary to fix a pipe 24 mm in diameter. It will serve as a handle, therefore, in order not to bend into three deaths, choose the length of the pipe for your height.

Attach wheels with a diameter of not more than 200 mm to the axle mentioned. The cultivator will rest on wheels, the height of the tool above the ground depends on the height of the wheels that we have adapted to it. By the way, the wheels need to be cut from metal 2-3 mm in thickness. After you have connected everything above, you can work on the ground.

The word cultivator does not only mean motor units. You can also use hand tools in your country house. It is much better than a standard boot and is much easier to make at home than a cultivator. Have you heard of the Tornado cultivator? It looks like a defective pitchfork.

DIY cultivator: selection

For a complete understanding of what awaits you after you decide to make a motor-cultivator with your own hands, you can look at the selection with a home-made unit.

Do-it-yourself cultivator

Let’s say you have a land plot. You want to cultivate it with a cultivator that you don’t have. Otherwise, you just wouldn’t have come here. You probably want to make such a unit yourself for some reason you know, whether it’s a lack of money for a factory motor-cultivator, or just an interest in making such a machine yourself. In this case, you are lucky, if you have an electric motor of 1.5-2 kW, a gearbox, then you can easily make a cultivator with your own hands in just a day.

DIY motor cultivator: where to start and how to make

The main parts of a homemade cultivator are a gearbox and an engine. First of all, we make the frame of the future cultivator, drill holes for installing the main units, and make handles for controlling the unit from two curved pipes with a diameter of 32 mm. Between the homemade handles, it is necessary to put another pipe, which will be like a spacer for us, increasing the strength of the structure. We will subsequently install a start button to one of the handles.

For the manufacture of the shaft, I used unnecessary scrap, welded an asterisk to it from the camshaft of a VAZ engine, and scalded the chain and both sprockets with metal making a cover.

I connected the three-phase motor according to the standard “triangle” scheme, place the capacitor starter button on the handle to make it more convenient.

Homemade cultivator “Tornado”

Tornadoes are easy to use thanks to a lever that the operator grabs on when rolling the cultivator into the ground. For the lever, we need a pipe, which we need to attach to the handle. The pipe should be 50 cm in length. For fastening, you can take electrical tape. As a pipe, you can use the handle on the handle, which is usually equipped with shovels. Such a lever will protrude 25 cm to both sides of the handle.

You can make a Tornado cultivator from springy steel. We take a plate half a meter long, 1-1.5 mm in thickness and 2 in width. Bend the steel, make a loop out of it, which you put on the handle. Watch the height of the cutting. It is important to observe the diameter of the resulting loop. it should not be more than 20 cm in diameter in order to freely enter the aisles.

There is another version of the cultivator. a rotary disc cultivator. We just warn you that you will need to exert a lot of physical strength to make the desired convex discs. Place regular metal discs and hit them with a hammer. In the process, they should become bowl-shaped.

The main part of the mechanism. namely the discs, we put on the bushing, which we attach to the axle. We attach both ends of the axle with cotter pins on a large bracket.

On a large bracket we make a hole where we insert a pipe with handles and a crossbar between them.
Place the rod on the small bracket using a welding machine. It should be 24 mm in diameter and 25 cm in length. Then screw a 16-diameter rod into the stem.

How to make a cultivator for a mini tractor with your own hands: drawings, assembly diagram and order of work

The cultivator for the soil is an indispensable assistant for any landowner, allowing you to cultivate the surface of the earth without disturbing its fertile layer. Therefore, it is not surprising that without such a mechanism it is difficult to count on a good harvest.

Today, a large selection of different cultivators is available on the market: a ripper, a hand cultivator, a rotary device, a motor cultivator. The area of ​​the cultivated area has a significant impact on the purchase of a particular type of unit.

An alternative to buying is to create this device with your own hands. We will tell you how to do this in this article using the example of a cultivator for a mini tractor with cutters.

Preparing for self-assembly

First of all, you must have the following materials in stock:

• Steel pipe more than 2 m long;
• Square steel plates (dimensions not less than 15×15 cm.);
• At least 20 nuts and bolts;
• Rectangular plates with a flat section (dimensions 20-25x5cm.).

Also take care of the tools:

• Discs for metal work;
• Angle Grinder;
• Welding machine, electrodes;
• Drill with drills;
• Emery machine;
• Standard tool kit (wrenches, screwdriver, pliers, etc.).

The final dimensions as well as the type of the above materials depend on:

• From the dimensions of a particular minitractor (tiller) to which the cultivator will be connected;
• From the type of connection of nodes;
• The type of tillage tool you plan to use.

Our next article tells about the nuances of using a tiller and a cultivator at a summer cottage.

Manufacturing process

The entire manufacturing technology is reduced to the following stages:

• Drill holes in all plates to connect them.
• Next, you need to fasten the square plate to the rectangular ones using bolts so that one cutter is located on each side of the square plate.

Homemade cutters for a mini tractor

The product is ready, but before proceeding with processing, be sure to make sure that each structural element is reliable.

Interchangeable equipment types

Depending on the tasks to be solved during soil cultivation, cultivators are supplied with various tools. The most common ones are:

• Paws. There are:

• Chisel-shaped. allow to loosen the soil up to 15 cm deep;
• Pointed flat-cutting (flat-cutters). destroy weeds, as well as work out the soil by 4-6 cm, allow not to raise the wet bottom layer to the surface;
• Pole-type universal. intended for inter-row or continuous tillage (working up to 14 cm). Such paws perfectly grind the soil, cut off weeds, partially raise the moist soil layers to the surface;
• Flat shearing one-sided (weeders, razors). perfectly cope with weeds.

Cultivator tines:
a. flat-cutting lancet, b. universal, c. loosening hard, d. loosening spring

Feeding knives. loosen the aisles, embed fertilizers in the soil (up to 16 cm);

Needle discs. destroy the earth crust, destroy weeds (tillage up to 4 cm, soil shift by 1-2 cm);

Arychniki-furrow cutters. designed to create furrows for irrigation (up to 20 cm);

Hillers. cut ridges (up to 25 cm), destroy weeds between the rows, and also cover the weeds, the depth of treatment with hillers is up to 16 cm.

All removable equipment is attached to racks, which can be connected to the frame in different ways.

And this article talks about making a potato digger with your own hands.

Recommendations

We bring to your attention several useful recommendations for assembling and using a homemade cultivator and its “working bodies”:

• Materials for the cultivator must be pre-treated with anti-corrosion treatment. If this is not done, the moisture contained in the soil will significantly shorten the life of the cultivator.
• Flat cutting paws have the same grip (220. 385 mm) with universal lancet paws, but there is a difference in crumbling angle: universal. 25-30 degrees and flat cutting. 12-18 degrees.
• To level the furrows remaining after the knife paw, it is necessary to install a weeding or loosening paw.

As you can see, making a cultivator yourself is not so difficult. The advantages of a homemade cultivator are minimal cost, adaptability to your needs in soil cultivation, and versatility. Such structures can be suspended from tillers, mini tractors, as well as tractors T-25, MTZ.

From this you will learn how to make a homemade cultivator for a mini tractor at home:

How to make a cultivator for a tiller with your own hands drawings. The main stages of creating a cultivator and the importance of their indispensable observance

How to assemble a cultivator on a tiller with your own hands? This lesson is quite simple for those who have the skills to work with similar devices and understand their design. To further simplify the work, there is a certain structure, implying a breakdown of the entire process into certain stages, different in their purpose and functional performance. These subsections look as follows and in the best way characterize the entire procedure for creating a device:

• Drawing up a plan for a future device;
• Collecting the necessary tools;
• Assembling the device.

A homemade cultivator, assembled in accordance with these criteria, will have the best qualities and will become an indispensable assistant both in the summer cottage and in your own garden.

At the same time, a self-made device will be convenient and practical, since in the process of assembling all the parameters and design features should be performed based on your own anthropometric data, in addition, based on your own preferences and desires.

Variety of choices

A tiller or cultivator will help make planting and caring for potatoes easier. In the work in the garden or garden, they are considered indispensable helpers. The plow is an integral part of the tiller. It can be reverse and disk. An additional adaptation to the technique is a hiller, which can be of several types.

It will not be possible to immediately determine which hiller is better. The choice of tillers is influenced by many factors, including the characteristics of the soil, the size of the land plot, the financial part of the issue plays an important role. Therefore, in order to make the right choice, you need to get acquainted with the description of the most common hillers for a tiller:

Flat cutters on the tiller: advantages and disadvantages of operating the device

Flat cutters can be safely called a kind of hybrid of a harrow and a knife. They are mounted parallel to the ground or at a slight angle. As a result, the device is immersed in the soil to a shallow depth and cuts off the roots of weeds, thereby turning the soil itself, contributing to a better preservation of moisture and nutrients.

In addition to these positive aspects, flat cutters:

• Improves soil condition;
• Destroy the crusts and lumps formed after heavy rain;
• Scare off pests;
• Prepare the soil for long-distance planting;
• Inter-row cultivation of crops is carried out;
• Saturate the top layer with oxygen.

Naturally, in some cases, the owners purchase flat cutters with a ripper for a tiller, which not only perform the above tasks, but also remove unnecessary load from a person, are easy to operate, do not need to be lifted and are distinguished by excellent productivity. Such devices often have a fairly affordable cost, but some craftsmen manage to create flat-cut rippers for a tiller with their own hands.

How to make a cultivator for a tiller with your own hands. DIY flat cutter for a tiller

In recent years, many land owners are increasingly using new technical developments that can make life much easier and spend much less time on performing certain tasks. tillers, cultivators, mini tractors and other devices have a tangible impact on the life of an agronomist.

If earlier traditional boots were relevant, which forced to work heavy soil in a half-bent state for more than one hour, today they are replaced by innovative flat cutters designed for operation together with a tiller.

Do-it-yourself flat cutter for a tiller: a simple method of manufacturing

If the tiller has quite impressive characteristics, it is advisable to make several flat cutters and place them on the device. Thus, an even more productive unit will be obtained, which will not only save time, but also energy.

For excellent cross-country ability of the created plane cutter, you need to take care of the appropriate wheels. Almost any material is suitable for them. An iron tube is an excellent choice as an axis.

Then, on both sides, when cutting concrete, it is advisable to weld two circles. Several wires must be attached along the diameter (using a welding machine), the diameter of which does not exceed 8 mm.

On the axis from the inside, it is necessary to leave room for placing the bearing and further installing the homemade flat cutter. Since the tiller body is not always made of a very durable material, the main focus is on the axle. After the bearing is attached, a plate should be welded to it.

Plane cutter knives can be crafted from split sections of the mower. Their lightness and compactness make them ideal components for cutting elements. It is important to make sure that they are securely fastened, otherwise the structure will walk from side to side and not perform its task efficiently.

Small wheels are often used to limit the immersion depth. An excellent “donor” can be a standard children’s car.

The wheels themselves can be supplemented with iron parts so that the plastic does not deteriorate while driving. The immersion depth must be at least 5 cm.

Any part of the weight can be welded on to increase the weight on the cultivator cutter and increase the pressure to enter the soil. In the case of a lack of necessary components, you can use a basket with bricks, but such a solution is not very convenient.

For a better understanding of the design features, it is suggested that you familiarize yourself with the drawings. The presented ones can also become a guide, because on these materials many craftsmen share their experience with users and reveal the secrets of creating a truly durable and reliable attachment for a tiller.

It is worth noting that the created plane cutter is suitable for both Neva tillers and equipment of the Centaur, Salut and others brands. The versatility of the product allows you to create a truly excellent assistant at home and without special financial costs!

Cultivator to the tiller with OWN HANDS. Mini EUROPAC. DIY tiller cultivator with your own hands. For mini tractor

To make a homemade cultivator for a mini tractor or for a tiller with your own hands, you need metal plates, square. The size is 1515 centimeters, rectangular. 254 centimeters and a steel pipe. You need to start making a cultivator with cutters.

In order for the cutters to be reliable and suitable for processing all types of soil, and not only loose chernozem, they must be assembled with bolts. holes must be drilled in the blanks, the number of which depends on the size of the metal strips, which will serve as blades.

The longer their length, the more holes are needed in order to securely fix them. Further, the strips are fixed to the workpieces, overlapping each other in a circle, and clamped with bolts.

Welding can also be used for these connections. But in this case, they will not be strong enough, and repair and replacement of knives will be a difficult process. Welding is used here to connect the cutters together. For this, holes are made in the workpieces, the diameter of which must correspond to the outer diameter of the pipe.

The cutters are put on over it and fixed with tacks, or short seams. This product can now be put on the shaft of a mini tractor and used for its intended purpose.

How to make a cultivator for a tiller with your own hands drawings. The main stages of creating a cultivator and the importance of their indispensable observance

How to make a tine cultivator?

To create such a cultivator, you must:

• 5 steel discs with a diameter of 30-35 cm,
• Steel bar 10 mm,
• Axle (32 cm long, 15 mm diameter),
• Wooden or plastic holder.

The drawing shows that holes must be drilled in the discs for sharp teeth, which must be made from a steel bar. After that, the discs are mounted on the axle, on the edges of which bearings and trunnions are put on.

The principle of operation of such a device is simple: sharp teeth, piercing the soil, raise its layer and loosen it. This saturates the soil with air and also removes small weeds. If one of the teeth is broken or falls out, repairs will be required, which can be done using a welding machine.

How to make a hand cultivator with your own hands?

There are at least two options here: Tornado (easy to manufacture, use, and, if necessary, also to repair) and a cultivator based on a bicycle frame.

A tornado is made from a pitchfork. Their teeth are bent like a corkscrew and then squeezed onto a plastic holder. The handle can be made from a plastic pipe of a larger diameter, fixed to the holder from the back side, as in the drawing.

Making this attachment from an old bicycle is more difficult, but if you follow the drawing, it is quite possible. To make it you need:

• Bike frame,
• Wheel,
• Material for making a head (a blade from a hoe, sharp rods, a plow or part from an old cultivator).

According to the drawing, the wheel and head are attached. The control part is made from the steering wheel. The parts are welded together or bolted without a shaft, tightly. This cultivator model is efficient to use and easy to repair.

How to make a rotary disc cultivator with your own hands?

This type of device is for removing weeds, breaking clods, loosening the soil. The most difficult part of making such a cultivator is discs. They are made not flat, but convex. This effect can be achieved with hammer blows.

To make such a cultivator, you need:

• Weld the discs to the bushings that fit on the axle. Their endings are fixed in brackets.
• In the largest bracket there is a protrusion through which the pipe passes, with a crossbar.
• Next, a rod should be welded to the smaller bracket, into which the rod must be screwed, with a part protruding above the crossbar.

How to make a cultivator with your own hands?

To facilitate the work on the personal plot, in the last century, such an indispensable tool as a cultivator was invented. However, the market for agricultural implements cannot boast of low for such products. Therefore, for summer residents who are tired of digging up the earth with a shovel, it will be interesting how to make a cultivator with their own hands.

How to make a cultivator for a tiller with your own hands?

You will need the following tools and devices:

• Hand circular saw and discs for metal to it,
• Welding machine,
• Emery of different abrasiveness (2 pcs.),
• Drill.

The source material from which the cultivator is made by hand:

• Stainless steel square plates 15×15 cm,
• Rectangular plates 12×4 cm from the same material (for making cultivator cutters),
• Steel pipe,
• Nuts and bolts.

• Guided by the drawing, it is necessary to drill each square and a cutter, then bolt the square on both sides with cutters.
• Attach the resulting part to the base. It is better to do this with bolts, since welding does not give the strength of the joints necessary for cultivating the soil.
• You need to do the same with all the squares.
• At the next stage of the assembly, when the working part is completed, it is necessary to make a hole corresponding to the diameter of the steel pipe.
• The pipe is cut in half, and welded to each of the formed parts along the undercarriage with cutters.

For greater clarity and accuracy of the specified instructions, it is recommended to look.

In the same way, you can make a cultivator for a mini tractor with your own hands, changing the dimensions of the parts if necessary. The difference is the hook, which can be made of stainless steel.

How to make do-it-yourself lugs for a cultivator?

So that the wheels of the cultivator do not get stuck in wet and plowed soil, and also do not tamp it, it is necessary to make lugs that will help to further plow the soil. By increasing the cross-country ability of a mini tractor or a tiller, they further increase work efficiency.

To perform the lugs, a welding machine is needed, which will also be needed if the cultivator needs to be repaired with your own hands, and you also need metal corners and wheel disks.

The sequence of work can be performed in two ways:

• The metal corner is cut and welded to the rim of the disc in segments, at a distance of 10 cm from each other. The formed protrusions will play the role of lug teeth.
• The second option for making homemade lugs is based on rims from a chopped gas cylinder, 7-9 cm wide. This is the basis for lug wheels. Using a welding machine, angular hooks are cut and welded to the rims with an edge, at a 15 cm distance from one another. A square plate is welded into the center of the rim, corresponding in diameter to it. An axis is welded to the center of the plate.

Such a lug is applicable not only on a cultivator, but also on a mini tractor and a tiller.

Do-it-yourself flat cutter for a tiller: a simple method of manufacturing

If the tiller has quite impressive characteristics, it is advisable to make several flat cutters and place them on the device. Thus, an even more productive unit will be obtained, which will not only save time, but also energy.

For excellent cross-country ability of the created plane cutter, you need to take care of the appropriate wheels. Almost any material is suitable for them. An iron tube is an excellent choice as an axis.

Then, on both sides, when cutting concrete, it is advisable to weld two circles. Several wires must be attached along the diameter (using a welding machine), the diameter of which does not exceed 8 mm.

On the axis from the inside, it is necessary to leave room for placing the bearing and further installing the homemade flat cutter. Since the tiller body is not always made of a very durable material, the main focus is on the axle. After the bearing is attached, a plate should be welded to it.

Plane cutter knives can be crafted from split sections of the mower. Their lightness and compactness make them ideal components for cutting elements. It is important to make sure that they are securely fastened, otherwise the structure will walk from side to side and not perform its task efficiently.

Small wheels are often used to limit the immersion depth. An excellent “donor” can be a standard children’s car.

The wheels themselves can be supplemented with iron parts so that the plastic does not deteriorate while driving. The immersion depth must be at least 5 cm.

Any part of the weight can be welded on to increase the weight on the cultivator cutter and increase the pressure to enter the soil. In the case of a lack of necessary components, you can use a basket with bricks, but such a solution is not very convenient.

For a better understanding of the design features, it is suggested that you familiarize yourself with the drawings. The presented ones can also become a guide, because on these materials many craftsmen share their experience with users and reveal the secrets of creating a truly durable and reliable attachment for a tiller.

It is worth noting that the created plane cutter is suitable for both Neva tillers and equipment of the Centaur, Salut and others brands. The versatility of the product allows you to create a truly excellent assistant at home and without special financial costs!

How to make a cultivator for a tiller with your own hands. The main stages of creating a cultivator and the importance of their indispensable observance

How to assemble a cultivator on a tiller with your own hands? This lesson is quite simple for those who have the skills to work with similar devices and understand their design. To further simplify the work, there is a certain structure, implying a breakdown of the entire process into certain stages, different in their purpose and functional performance. These subsections look as follows and in the best way characterize the entire procedure for creating a device:

• Drawing up a plan for a future device;
• Collecting the necessary tools;
• Assembling the device.

A homemade cultivator, assembled in accordance with these criteria, will have the best qualities and will become an indispensable assistant both in the summer cottage and in your own garden.

At the same time, a self-made device will be convenient and practical, since in the process of assembling all the parameters and design features should be performed based on your own anthropometric data, in addition, based on your own preferences and desires.

Do-it-yourself cultivator for a tiller drawings and dimensions. How to make a tiller cultivator

Before making a cultivator for a tiller with your own hands, it is necessary to treat all metal elements with a special anti-corrosion compound against the premature appearance of rust after frequent contact with the ground.

Simple models can be made without drawings. To make and correctly assemble more complex devices, it is necessary to plan the work, calculate the dimensions of the module and parts.

A homemade pitchfork cultivator is an easy way to recycle (rework) products. For this, the teeth of the mechanism are bent with a hammer like a corkscrew and are mounted on the handle. A shovel handle is used as a handle. For fastening use electrical tape.

Some craftsmen manage to make a cultivator with their own hands from a bicycle frame with a wheel. A steel rod is welded or bolted between the 2 base blocks. The head is mounted to the cross member. For this design, it is recommended to take a medium-sized wheel.

In order to competently assemble a disc cultivator and work correctly with cutters, it is necessary to design schemes of assemblies and individual parts. Taking into account the deformation of the discs, special adjusting nuts are used. The discs are welded to bushings located on a rotating axle with brackets. On the bracket, it is necessary to provide a protrusion where the pipe will pass. The cultivator handle is attached to the pipe surface.

Advantages of MTZ models

• Versatility, thanks to which you can connect any attachment to the tiller to facilitate agricultural work. The design provides not only the use of plows, cutters, harrows, and other things, but also brushes, plows and snow blowers for cleaning the territory.
• Small dimensions, allowing the tiller not to take up much space during storage.
• Maneuverability thanks to a well-thought-out design despite the significant weight of the unit.
• Easy to maintain.
• The ability to repair without resorting to the services of service centers.
• Low quality requirements for fuel and lubricant.
• Spare parts availability.

Homemade cultivator for a tiller with your own hands. For mini tractor

To make a homemade cultivator for a mini tractor or for a tiller with your own hands, you need metal plates, square. The size is 1515 centimeters, rectangular. 254 centimeters and a steel pipe. You need to start making a cultivator with cutters.

In order for the cutters to be reliable and suitable for processing all types of soil, and not only loose chernozem, they must be assembled with bolts. holes must be drilled in the blanks, the number of which depends on the size of the metal strips, which will serve as blades.

The longer their length, the more holes are needed in order to securely fix them. Further, the strips are fixed to the workpieces, overlapping each other in a circle, and clamped with bolts.

Welding can also be used for these connections. But in this case, they will not be strong enough, and repair and replacement of knives will be a difficult process. Welding is used here to connect the cutters together. For this, holes are made in the workpieces, the diameter of which must correspond to the outer diameter of the pipe.

The cutters are put on over it and fixed with tacks, or short seams. This product can now be put on the shaft of a mini tractor and used for its intended purpose.

Cultivator for MTZ tiller. Description

The active growth and development of small-scale farming in the 90s provoked industrial enterprises to produce compact units to facilitate the performance of agricultural work. These machines significantly outperformed tractors that the average farmer could not afford to maintain. They were not only compact in size, but also highly maneuverable and efficient.

However, the Minsk Tractor Plant (MTZ) by this time had already introduced to the agricultural market the small-sized models Belarus-05, MTZ 082 and MTZ 112, which immediately gained popularity due to their reliable design and ease of maintenance. Serial production increased and it was decided to transfer further production to the Smorgon Aggregate Plant, which was a branch.

The MTZ lineup was expanded with tillers with different characteristics and, accordingly, they wore different indexes in the name 05, 06, 07, 08, 09, 10 and 12. But only some 05, 06, 08, 09 and 12 gained popularity thanks to the successful combination functionality and reliability. Today, the main attention at MTW enterprises is paid to the production of models 06 and 09.

Tiller cultivator

Cultivators are used for continuous tillage of the soil before sowing and for cultivating crops, loosening, weed control, moisture conservation, hilling.

The difference between a cultivator and a plow. the cultivator performs loosening without turning the soil layer.

Cultivators consist of a cultivator rack and a cultivator arrow photo.

• Flat cutting duckfoot cultivator share
• Universal cultivator share
• Rigid loosening cultivator share
• Loosening spring cultivator share

Arrows of cultivator paws are made of steel grade 65G, when sharpening cultivator arrows, the metal must not be overheated.

It is also possible and necessary to harden the cultivator arrow, heat it. For hardening, the paw is heated to 820 ° (light cherry-red heat), after which the arrow is cooled by lowering it into an oil bath. After cooling, the cultivator arrow is released, that is, it is heated again to 400 ° (gray tarnishing) and slowly cooled in air.

After such operations, the file does not leave any trace on the cultivator arrows and the cultivator paws normally perform their work on tillage.

Flat cutters on the tiller: advantages and disadvantages of operating the device

Flat cutters can be safely called a kind of hybrid of a harrow and a knife. They are mounted parallel to the ground or at a slight angle. As a result, the device is immersed in the soil to a shallow depth and cuts off the roots of weeds, thereby turning the soil itself, contributing to a better preservation of moisture and nutrients.

In addition to these positive aspects, flat cutters:

• Improves soil condition;
• Destroy the crusts and lumps formed after heavy rain;
• Scare off pests;
• Prepare the soil for long-distance planting;
• Inter-row cultivation of crops is carried out;
• Saturate the top layer with oxygen.

Naturally, in some cases, the owners purchase flat cutters with a ripper for a tiller, which not only perform the above tasks, but also remove unnecessary load from a person, are easy to operate, do not need to be lifted and are distinguished by excellent productivity. Such devices often have a fairly affordable cost, but some craftsmen manage to create flat-cut rippers for a tiller with their own hands.

Disadvantages of MTZ tillers

• High cost in comparison with analogues from other manufacturers;
• Fuzzy gear fixation (as noted by the owners);
• The need to apply effort to switch the differential;
• Compulsory running-in before use.
• Weight. It can be attributed to the advantages and disadvantages at the same time, because with such tillers it is rather difficult to manage on wet soil.