How to wear a fishing line for a trimmer on a lawn mower. Video Instructions, how to wrap and fix a fishing line for a trimmer on a trimmer

How to wind a fishing line for a trimmer for a trimmer for grass: guides and video instructions

A beautiful lawn will look truly well-groomed only if you regularly give up grass. For processing complex areas, a trimmer for grass is best suited. Any owner of the unit will sooner or later collide with the solution to the problem, how to wrap a fishing line for a trimmer to a coil, because from incorrect actions you can not only worsen the quality of the mowing, but also disable the equipment. Today in the Homius review, we will talk about all the ways and nuances of the replacement of fishing line and the features of the selection of consumables.

It is convenient to use a trimmer for grass for pumping small or complex areas, for example, near the hedge, between the beds and along the paths. Today, manufacturers produce a wide variety of gasoline, electric and battery models, which can be selected for any requests of the owners.

The Easy Way to String Your WEED EATER

As a cutting element of a trimmer for grass, a fishing line for a trimmer is used. In the process of work sooner or later, its length will end, and then the owner will arise the question of how to properly replace and fix the thread tucked in the removable coil.

What to consider when choosing a fishing line

Before inserting and fixing the fishing line for a trimmer in a removable coil of a trimmer for grass, it is important to choose the right material.

Rating of the best models of gasoline trimmer for grass. Review of manufacturers and models, as well as useful tips from experts considered in this review, will help in a difficult choice among many models of devices.

By quality

Before you put a fishing line for a trimmer on a trimmer for grass, you need to pay attention to the cross section of the cord:

  • Round cross.sections are the most common option. They perfectly give way to grass even in complex areas;
  • A line for a trimmer with a spiral section is suitable for thin grass. It is not very durable and is not suitable for old thickets;
  • The cord with zabrinki and sharp faces is chosen for mating by the weeds;
  • A fishing line for a trimmer with a variety of geometric sections will help to mow the lawn more evenly, but the strength of the consumable material is low.

Important! The most wear.resistant consumables are a two.component fishing line for a trimmer with a round section, enhanced from the inside.

The owner of Motokosi should know that it is categorically impossible to use metal wire, fishing thread and a variety of strings.

Rating of the best electric trimmers for grass. In this review, we will analyze the criteria for choosing an electrochemmer, technical characteristics, as well as the most popular models and brands according to consumer reviews.

In size

Before winding the thread, you should pay attention to its size to the coil of the trimmer for the grass. Most often use a fishing line for a trim with a cross section of 2 mm.

You can choose the right diameter in the following ways:

  • View recommendations in the manufacturer’s instructions for trimmer.
  • Often manufacturers apply information about the cross.section to the bobbin.
  • The cross section of the cord should be suitable for the diameter of the coil opening.

Important! The thicker the thread will be seasoned, the more rigid grass it will be able to mow.

How to replace a fishing line for a trimmer on a trimmer?

Replacing the fishing line of the trimmer for the grass with instructions will even allow the owner of the lawn mowed inexpensive in such matters to do a fairly difficult job.

However, before starting work to replace the fishing line on the trimmer, it is necessary to ensure the safety of work. In particular, it should be taken protection measures against careless or spontaneous inclusion of the lawn mower:

  • Exclude spontaneous start,
  • Delete the battery (if used),
  • Place the tool on a comfortable site for work.

It is convenient to perform work on replacing the fishing line for the grass when the lawn mower lies on the table, and the master, who is performed by replacing the fishing line of the trimmer for the grass, has the opportunity to approach the instrument from any side.

Remove the head of the head of the grass for the grass

At the first stage of disassembly, the head of the head of the grass is removed. On the example of the models of trimmers “Black and Decker” and others, it is usually enough to apply some pressure to squeeze the click-fixer, which are on the side of the head of the head of the head of the head of the head of the body to remove the lid to remove the lid.

Some models of lawn mowers initially include dismantling the head of a trimmer for grass, for which a playback key is used, which is included in the tool kit. The head is usually held by two or three screws, access to which is provided through the side holes of the rear decorative cover.

The head cover, where the coil with a fishing line is installed, is usually held due. It is enough for some effort to squeeze the tongue-thorough and slightly turn the lid, after which the lid is easily removed

At the time of squeezing the tongue-fixer, you need to turn slightly and raise the head of the head of the trimmer for the grass to remove the winding drum.

Step two: extracting a winding drum (coil) with a fishing line

The next step in the process is the exhaust drum with a fishing line from the inner region of the head. You need to turn the head with an open side to see a fishing line for a trimmer and a reel. On the side of the head, find two recesses (eyelets) through which the fishing line for the trimmer is bred outside.

wear, fishing, line, trimmer

You should release a fishing line for a trimmer from the holes by checking the drum. Then gently remove the coil from the head of the head. The winding drum of some models is installed on the spring. This moment must be taken into account by performing the operation to extract.

The procedure for extracting a coil of a trimmer for grass with a fishing line from the inner region of the head: 1. head assembly with a coil; 2. extracting neatly with a small axial turn; 3. extracted details

The old fishing line for the trimmer is completely removed from the coil. To remove the old fishing line for grass, you need to remove the forest from the loops and pull the free end. This method is removed by the whole old winding. A similar process is repeated on the second section of the drum. The master is recommended to use gloves when performing work.

Installation of a new fishing line on the coil of a trimmer for grass

Equipping the coil with a new fishing line is performed in the reverse order. The procedure looks like it is described below, regardless of the model of the lawn mower:

Step one: fixing and styling

Fold the end of the fishing line in half. Place the workpiece above the coil on each side of each half of the winding area. Wrap both halves completely around the winding drum. Stretch the fishing line for the trimmer through the loop.

The procedure for preparing fishing line in the field of both wound sections of the drum. The loops are laid in specially made cutouts, after which the winding of the fishing line is performed in each area

Pull the fishing line for the trimmer enough and put the knot in the groove made on each side of the winding drum.

Step two: winding cutting material according to sections

The next step is to turn the fishing line in a circle of coil, observing caution. It is necessary that each half be filled with “its own” winding, exactly, without intersections. Usually on the hull of the winding drum you can see the arrows indicating the direction of winding. This moment should be borne in mind, filling the reel with a fishing line.

Step Three: The Club of the Head Noner

Stretch the ends of the fishing line through a pair of oval cuts of coil. Replace both goals and a spring (if any in the design) with new elements included in the package. Bend both ends of the fishing line at right angles.

The last technical stroke of the process of replacing the fishing line on the trimmer is to put the cover on the head with subsequent fixation by pressure and slight turnover.

Let each end into the hole, which is at the base of the winding drum. Install the coil in the inner area of ​​the head with an emphasis on the spring. Put the lid, leve on the base and light pressure down with a small rotation counterclockwise, put the cover on the tongues of the latch. This is where the replacement procedure is completed.

We carry out the winding of the fishing line

Sentlessly completed disassembly of a spray coil without losing its spare parts allows you to go to the main task-winding into a fishing line coil. Technological features of the design of the spool and the number of working antennae determine the sequence of actions.

Coil with one working osik

The easiest option and a simple sequence of actions:

  • The dimensions of the bobbin and the length of the original factory winding determine the length of the fishing line recommended for winding. 2 5 m.
  • One end of the fishing line is inserted into the fixing technological hole located inside the spool.
  • The fishing line for the trimmer is wound on the drum in reverse rotation of the spray in the trimmer product direction. as a rule, on the inside of the bobin, the arrow indicates which direction the winding is carried out.
  • A small section of the fishing line is left free to output it. it is fixed in a specialized border on the inside of the bobbin, designed to keep the winding when assembling a spool in working condition.
  • The left end of the fishing line is passed through the hole of the outer part of the bobbin.
  • Half of the bobbin are collected and put on the bar of the trimmer device.

Two working antennae

In this type of spools, the number of grooves for winding the fishing line lying on the inside of the coil should be determined:

For both cases, a fishing line for a trimmer 2-3 m long is taken. In a single.captable coils, the fishing line for a trimmer stretches into a through hole, its ends (antennae) are folded together and aligned, after which they are wound in the back of the rotation of the bobbin on the bar the side. inside the arrow is usually indicated the correct direction of the winding. In the presence of fixing grooves, the ends of the fishing line are threaded in them or hold their free arm fingers, spread into the through hole of the outer half of the bobin, the spool is closed and attached to the bar of the trimmer product.

The difference between the winding of the fishing line in the two-to-dancing coils is that initially a line of fishing line 2-5 m long is folded in half (to determine the middle fold), and the bend loop is inserted into a special groove between the grooves. Both strains of the fishing line are wound each in its own groove, fixing the antennae and assembly of the coil is similar to the option considered above with one groove.

The first implementation of this procedure may seem long and quite time.consuming, but over time and experience, this task will be solved much faster and easier.

The video below will clearly show how to refuel a fishing line for a trimmer to the coil of a trimmer for the grass and correct it correctly. this operation is not a complicated one and, with some patience, will necessarily be crowned with success:

Supercut braid head

This two.string design is also designed to mow and clearing space and is used in obstacles and processing large areas. For the cutting cord, an automatically supported optimal cut length is implemented here. It is used only with a universal or special protective shield for the mowing.

We will explain how to refuel a fishing line for a trimmer to a trimmer coil for the grass of these two modifications. First, prepare two strings of maximum length (7 m or 10 m), depending on its type. You can find out these data on the packaging sheet.

  • Take the head in your hand so that its cover with a bulge in the center is from above. Thick two recesses located on the sides of the structure with the other hand. they are exactly opposite each other. Press your fingers in these recesses at the same time or in turn so that the constipation comes out of the hook, and then click the other. Turn the lid clockwise: now it can be removed and put aside.
  • Take the coil itself. To do this, slightly cram it to free the plastic hook. With rotational movements, bring it out of the holding position and raise it up. A free drum with two compartments will be in your hands.
  • Find the ear, which adjoins the dividing wall in the middle of the bobbin. Take a fishing line for a trimmer for a trimmer for grass and insert its end into this recess until it stops. Having bent the string, wrap it around the coil in the opposite direction so that the fixed piece of the trimmer cord does not fall out of the ear. With quick and confident movements, continue to wrap the line for the trimmer turning behind the turnover, trying to distribute the layers evenly and tightly. Когда отрезок закончится – другой конец струны зацепите за одну из двух насечек так, чтобы наружу выходил остаток примерно 10 сантиметров.
  • Make the same actions with the second string. Wrap a fishing line for a trimmer in the second compartment on the same side. Fix the free end of the same length on a notch located on the opposite side. After that, the coil can be inserted back into the body.
  • With rotation of the bobbin, compare the strings and sleeve inserted into the head so that they are next to each other. Take each of the forests, carefully unhook it from the notch and put it in a special groove for exit outside. Now the ends stick out of the channels of the rumps and the lid can be closed. Put it on in accordance with the position of the fixers and press it strongly to the click.
  • Pull strongly by one string so that the reel body shifting a little up. You will hear another click, and part of the fishing line will come out a couple of centimeters.
  • The next action can be cut out by the ends of each string by the secateur to the required equal length, if necessary. STIHL recommends that the trimmer fishing line protrude from the hole for about 10 cm.

Autocut C

The mowing head of the following type is also equipped with a coil for a cutting string, and its feed occurs during the operation of the tool, as in the variety Autocut without a letter from. However, in this modification, the replacement of the trimmer cord is carried out especially quickly and simply. When installing it, it is not required to open the mowing head and prepare two identical segments.

  • Before filling the fishing line for the trimmer into the coil of the trimmer for the grass, set the handle with the handle when the arrows on the head are nearby opposite the round recesses.
  • Remove the cutting string of maximum length. 8 m. and insert its ends into the opposite holes of the drum. It is necessary to ensure that the ends of the forest are trimmed with a bevel. After that, rotate the coil in the direction indicated on the lid. clockwise. Thus, a fishing line for a trimmer for a trimmer for grass is completely wound on a bobbin.
  • Cut a protruding loop in the middle. The resulting ends of the string should protrude from the drum for about 12 centimeters.


In order to change the fishing line for the trimmer, it is necessary to extract the old one (if it was).

The coil is part of the design of the trimmer for the grass, which is located inside the head of the motorcosa, drum or bobbin. Depending on the manufacturers of the head can be different. But this article discusses only Patriot, although their mechanism is used by many other companies.

Now you need to understand how to properly remove the head from a trimmer for grass and how to get a drum out of it.

Instructions on how to promote a hand head on a trimmer is described below.

  • First of all, you need to clean the head of dirt and adhering grass if it is contaminated. To do this, you need to raise a motorcycle head up and, holding the casing, remove a special protective cover dressed on the drum.
  • The next step needs to remove the reel from the drum. The coil is easily removed even with one hand, because it is not fixed inside the drum.
  • The drum itself is fixed in the trimmer with a bolt. This bolt must be unscrewed, after which you can easily pull out the drum. To do this carefully, you should support the drum with a coil, while twist the screw counterclockwise.
  • Now you can pull the coil out. As mentioned above, it is not fixed in anything except a hook with a metal shaft, so it does not need to be torn off with force. Neatly, in a circular movement you should pull the coil from the drum.
  • Now it remains to extract an old fishing line for a trimmer and follow the following instructions.

Installation of the coil and drum in its former place is performed according to the opposite algorithm.

Before the process of refueling the fishing line, it is worth making sure that the thread suitable for a trimmer was bought. In the case when the thread is not suitable, the fuel or energy consumption increases, as well as the load on the motor motor.

In order to replace the thread itself directly, you need to prepare a piece of thread of the required size. Most often, this requires about 4 m fishing line. A specific figure will depend on the parameters of the thread, for example, its thickness, as well as on the parameters of the coil itself. If it is not possible to accurately determine the length, it can be done as follows: insert and wind the thread to such a state that the coil is completely charged (the level of the fishing line will be compared with protrusions in the sides of the coil). It is necessary to ensure that the fishing line for the trimmer sits in the coil exactly.

Do not forget that the thick thread will be shorter than thin.

The instructions for refueling the fishing line in the coil is described below.

  • The prepared thread must be taken and turned in half. It should be ensured that one edge is longer than the other by 0.1-0.15 m.
  • Now you need to take the ends in different hands. The one that is smaller must be pulled to more, so that it becomes 2 times shorter. When bending, the indentation should be maintained at 0.15m.
  • Find the slot inside the coil partition. Carefully prick the loop that turned out earlier in this slot.
  • To continue work, it is necessary to determine the direction of winding the thread in the coil. To do this, just examine the coil. there should be an arrow on it.
  • If the gunner could not be found, it is quite possible that there is a written designation. An example is given in the photo below. It is necessary to inspect the head of the coil. It has a direction indicator. However, this is the direction of the coil movement. To get the direction of winding, you need to wind in the opposite direction.
  • Now you need to season the reel with a fishing line. It is worth noting that there are special guide grooves inside the coil. When wrapping a thread, you need to follow these grooves, otherwise you can damage a trimmer for grass. At this stage, you need to charge the coil very carefully.
  • When the user winds up almost the entire thread, you should take the short end (do not forget about the protrusion of 0.15m) and stretch it into the hole located in the coil wall. Now you need to repeat this action similarly with another end (on the other hand).
  • Put the coil itself in the coil head, before that, extinguishing a fishing line for a trimmer through the holes inside the drum.
  • Now is the time to return the drum to your place. After that, you need to take with both hands by the ends of the fishing line and pull them to the sides. Then you need to put the lid in place (here you can safely make efforts until a characteristic click is heard).
  • Remained to perform “cosmetic work”. You need to see if the thread has come out too long. You can start a trimmer for the grass and check in practice whether everything is comfortable. If the thread came out a little long, you can cut it with scissors.

Frequent errors

Although the winding of the fishing line is a very simple task, many newcomers can wrap a fishing line for a trimmer incorrectly. The most common errors are presented below.

  • Many people when measuring the thread think that 4 m is a lot. Because of this, people often measure less, and they, accordingly, do not have enough fishing line. Do not be afraid to measure a lot, because you can always cut off the excess.
  • In a hurry, some people do not observe the gas stations inside the coil and wind up the thread like it. This leads to the “departure” of the fishing line from the coil and can even cripple.
  • For winding, it is worth using only the corresponding fishing line for the trimmer. This error is most common. You need to monitor not only the thickness and volume of the fishing line, but also your type. You should not use the first fishing line for a trimmer for wrapping, which will not match the goals. For example, you do not need to use a thread on the young grass, if it is necessary to mow dry.
  • Do not turn on the device until complete winding and collection. Although this is obvious, some people do this in order to check if everything is done correctly.
  • In no case should you confuse the refueling direction, as it will overload the engine, and it will soon get out of the working condition.

Beginners are quite characteristic of mistakes, so it is necessary to observe the advice given in this article.

The choice of fishing line

In order to easily wrap a fishing line for a trimmer to a trimmer coil for grass, it is worth deciding on what tasks the garden tool will perform. The thicker the thread tucked into the head, the more difficult the tasks that it can complete. It should be noted that a universal thread is often used, the width of which does not exceed 2 mm. You, in turn, can decide on the size, using the following methods:

  • get acquainted with the information set out in the instructions from the manufacturer;
  • check the suitability of the fishing line for use on your own, trying to insert it into the coil hole;
  • study the spool for information about diameters allowed for use.

Selection of fishing line for refueling a trimmer for grass can be carried out by engine type. So, for example, an overly thick thread can affect an increase in rotational resistance. Because of this, the load on the engine will increase, which will certainly affect the quality and timing of its further operation.

Avoiding negative consequences is easy. To do this, it must be borne in mind that for electric motors with a power of up to 500 W, a fishing line for a trimmer with a diameter of up to 1.2 mm is ideal. If you cannot get such a thread, you can use the cord by 1.6 mm. A thread with a diameter of 2 mm, in turn, is used for engines with a power of more than 1 kW. It is worth noting that the cord for 2 mm is often used for winding on a bent mower. If the gasoline device has a straight shaft, the thread should be used 2.5 or 3 mm. The thickest fishing lines are installed exclusively on devices, the power of which is equal or exceeds 1.3 kW.

wear, fishing, line, trimmer

The last, but no less important factor is the type of fishing cross section. When choosing it, it is worth focusing on the tasks set before the garden tool. There are several demanded cross.sectional options:

  • twisted-has a small margin of safety, which is why it suits exclusively for young grass;
  • Substitute. is characterized by sharp edges suitable for working on overgrown weeds;
  • Round. the most common section. Such fishing lines cope well with fresh grass, but they are not suitable for shrubs and dry ones;
  • rectangular, square and star type of cross section-due to low strength, are used to work on lawns.
wear, fishing, line, trimmer

The most durable and universal cord is a two.component fishing line for a trimmer with a round cross section, inside which the core is located. It is this thread that is suitable for the majority of work. It must be remembered that the use of fishing fishing line, ordinary wire and other materials as a cord pose a danger to others.

Removing and disassembling the coil

In order to correctly wind the fishing line for a trimmer to the coil of a trimmer for grass, you must familiarize yourself with the structure of the trimmer head. It consists of a protective casing, a bobbin with a thread, a hull cover, as well as a spring that is present only in some devices.

Starting to disassemble the coil, you must completely turn off/de.energize the device. In this case, the method of work directly depends on the type of head. The first option is to conduct the following actions:

  • The user presses on fixers located on both sides of the cover.
  • After removing the lid, the spool is extracted. Some models may have a spring, which also needs to be extracted.
  • A screw is located in the center of the case, which should be unscrewed with a regular screwdriver.
  • When the fasteners are removed, it remains to remove the gearbox from the shaft, gently shaking the case of the product body.

The second option for removing the coil for refueling the fishing line in a trimmer for grass is to tighten the head for the gearbox shaft. To carry out such a procedure, many devices are equipped with a hole into which you can insert the tool. When the screwdriver is inserted, the user can only take up the product body and scroll it clockwise. It is noteworthy that this method, in contrast to the previously described method, differs in the simplicity of execution.

How to remove and disassemble a coil

Before proceeding to the process of replacing the cord, users of trimmers need to remove and disassemble the coil. Consider how to do it.

The mowing head of a trimmer for grass consists of several parts: a casing, springs (not in all models), bobbins with a cord and cover.

wear, fishing, line, trimmer

Attention! Before proceeding with any actions to maintain an electric unit, it must be disconnected from the network.

In trimmers, 2 options for fastening the mowing head are most often used.


To remove the head of the trimmer for the grass, it will require its complete disassembly.

  • To remove the lid covering the inside of the head, it is necessary to press on the latch (latches) located on its two sides.
  • Removing the lid, you will see the spool that must be removed from the body. In some coils, a spring is installed under the bobbin, which must be carefully pulled out so as not to lose it in the grass.
  • Removing the bobbin, in the center of the case you will see a screw with a slot under a cross.shaped or flat screwdriver. It is possible that there may be a bolt under the hexagon or nozzle “Asterisk”.
  • Using a screwdriver, choosing the necessary bat (nozzle), you need to unscrew the bolt (counterclockwise).
  • After extracting the fasteners, take up the part of the part and, shaking it in different directions, remove the gearbox from the shaft.


In this version, the head is twisted onto the gear shaft. To remove it, you need to fix this shaft. To do this, in such trimmers, for example, in the Huter and Champion devices, a hole is provided through which you can insert either a thin screwdriver or a metal rod.

So, to remove the bobbin, take 2 simple steps.

  • Insert the screwdriver into the hole and stall the shaft.
  • Take the head of the head and start twist it clockwise. It should be twisted in this direction for the reason that the thread cut on the shaft is left.

Field winding algorithm

Depending on which model of the trimmer for grass is used, the type, thickness and length of the fishing line is selected. The diameter of the cord can be from 1.2 to 4 mm. It is not difficult to guess that the thicker you will refuel the cord, the more rigid and thick grass it is able to cut off.

In most cases, a universal fishing line for a trimmer with a diameter of 2 mm is used.

In order to find out which line diameter can be used on your mower, there are 3 ways.

  • View information about the thickness of the cord in the instructions for the apparatus.
  • Look at the squash itself. It can be given information about possible fishing line diameters.
  • Insert a fishing line for a trimmer into the output. If it passes into it without difficulty, then the cord of such a diameter can be used.

The fishing line for a trimmer is wound on a coil in a mowing head. Therefore, first it needs to be opened (this was mentioned above). There are 2 methods of winding the cord.

The first way

To correctly determine how many meters of the fishing line are required for a specific coil, it is necessary to wind it on the bobbin so that the skein does not exceed the diameter of the sides. If the fishing line for the trimmer will look out beyond the edges of the coil, you cannot insert it into the casing. After you have decided on the length of the material, it must be tucked in a bastard, so do the following.

  • It is necessary to fold the fishing line for double so that one end is 10-15 cm longer from the other.
  • Please note that the bobbin is divided into 2 parts by the central side, from which charging begins. Find a groove on it and insert a cord into it, bent twice, putting a slight effort.
  • It is very important to determine in which direction the fishing line for a trimmer is wound on the reel. If you look closely, you can find an arrow on the bobbin or an inscription with an arrow indicating which direction the winding should be carried out. There are times when there is no arrow on the coil. In such a situation, you can look at the arrow drawn on a mowing head, and wind the cord in the opposite direction.
  • Winding should be carried out carefully, a turn to the turn, with maximum thread tension.
  • After laying the cord is completed, you will need to fix it first the short end of the fishing line, inserting it into the groove suitable in diameter on the side of the coil.
  • The second end, the one that is more authentic, is attached into the groove on the opposite side of the squash.
  • After fixing the fishing line, cut its ends, leaving the allowances about 10 cm.
  • Next, it is necessary to install a refueling coil in a mowing head. To do this, alternately inserting and pulling the thread into the weekends of the head, place the bobbin in the casing, after which, by applying the required force, pull the fishing line for a trimmer from the fixing grooves and tighten it.
  • Now you can put on the lid and fix it with the help of latches.

The second method

Some coils provide a second method of fixing the cord: you can charge 2 sections of the thread, instead of one folded in half. Fishing line replacement occurs according to the following algorithm.

  • Before changing or charging a new thread to the coil, determine how many meters it will be required by the way discussed above.
  • Bend one end of the cord in the form of a hook.
  • Find a hole intended for fixing the fishing line at the bottom of the bobbin, and insert the end of the thread bent by a loop into it.
  • Wrapping the cord is required according to the direction of the arrow to the required level not exceeding the diameter of the coil.
  • Do the same actions for the second cell of the bobbin.
  • The assembly of the head is no different from the method that was given when the refueling of the bobbin was considered folded by half a piece of fishing line.

There is a very simple and quick way to replace the fishing line for motor.cuts without disassembling the mowing head, which you can see this video.

The ends of the cord sticking out of the holes in the casing can be cut to the required length, already when the part is installed in the trimmer. You can do this in two ways:

  • By turning on the trimmer for the grass (when rotating, the ends of the fishing line will part on the knife, fixed for these purposes on the protective casing);
  • Cutting the extra ends with scissors so that they do not touch the casing body.

The second method is used if I had to put a large diameter cord, and a trimmed knife cannot shorten it.

If the thread was charged into a mowing head, but the length of the protruding ends of the cord is insufficient, then before starting the device they must be lengthened. this applies to the head with manual adjustment. However, there are cases when using a semi-automatic mowing head, when, due to the insufficient length of the protruding ends of the cord, they do not automatically lengthen. In this case, it is necessary to turn off the unit (on the electric device you need to pull the fork out of the outlet), manually press the button located at the bottom of the part, and stretch a little fishing line. After this procedure, the cord will be able to advance again thanks to centrifugal strength, if you put the maximum spindle speed.

No matter how thick the fishing line for the trimmer you should remember: in order not to constantly interrupt the work and do not change the cord, you should avoid areas where a working tool can touch hard surfaces (stones, borders, thick dry branches, etc.D.).

How to choose a suitable fishing line for a trimmer?

For trimmers working both from electricity and gasoline, nylon fishing lines are suitable. This consumable can be used for both a hand tool and for a lawn mower on wheels. It is important to choose the right fishing line for a trimmer, as this directly affects the result of the work and the service life of the unit. Of course, in the proposed assortment of forests it is very easy to get confused, especially beginners. However, there are many tips from specialists and those who have already tried various options.

For an electric trimmer for grass with a capacity of less than 500 W, a thin fishing line for a trimmer with a diameter of 1 to 1.6 mm is suitable. She will perfectly cut the lawns with low grass. If the tool power is in the range from 0.5 to 1 kW, then it is better to give preference to a fishing line whose diameter will be 2 mm or slightly larger.

This will be enough to mow thin grass or grown weeds, but not too thick.

For gasoline trimmers, as well as motorcycle, you can not take a fishing line for a trimmer less than 3 mm. Such a thickness will easily cope with any weeds, dry stems, thick grass. A diameter of more than 4 mm is suitable exclusively for gas troops with high power. It turns out that a thick fishing line for a trimmer is necessary for powerful equipment. It is not recommended to use it for low.power trimmers, otherwise it will work poorly, constantly wound on the coil and create an additional load on the engine.

As a rule, in standard packaging is up to 15 meters of fishing line. However, to replace the string on the coil, about 7 meters long enough. It also happens that a fishing line for a trimmer is produced by bays of 250-500 meters. Be sure when choosing a string, you need to clarify the date when it was made. Too old nylon can be superior and become too brittle. If this happened, then you can soak the fishing line for a trimmer for a couple of hours in water, but it will not be completely the same.

When choosing an important parameter, the section of the string, which is of several types.

Round section is universal. It is used for mowing grass of medium thickness and density. When working can be unnecessarily noise, but it is not used too quickly.

Square or polygonal section is more effective compared to round. Thanks to the sharp corners, the stalks of plants are cut off at a higher speed and better.

Ribbed, twisted and star.shaped section is the most effective. Such a fishing line manages to mow the grass very quickly. And its main disadvantage is to quickly wear.

The fishing line for a trimmer for a trimmer for grass is made of nylon, which is durable, light, low price and wear resistance. To make the cost of the material even cheaper, polyethylene is added to it, but then the fishing line for the trimmer overheats faster. In thick strings there is a rod made of graphite or steel. Sometimes they are reinforced, which increases the strength and service life.

It is worth noting that the for two.component strings are higher than for standard nylon.

The device is in a mower

In the trimmer, the element on which the string is pulled is very simple. It is called the “coil”. Usually it consists of the upper and lower part (grooves), between which a partition with a deepening passes. It is on these grooves that you need to wind a fishing line for a trimmer. However, before it is extended through the recess.

Before pulling out the coil, you should twist a special button located directly on the housing of the lawn mower. Before changing the fishing line for the trimmer, it is necessary to remove the coil from the mowing.

It is easy to do this, but there are features depending on the configuration of the trimmer for the grass and the coil itself.

In small electronic braids, the motor and coil are in the lower part, and buttons are located on the sides of the bobbin. If you press them, then get the upper groove of the coil and part where you need to wind the fishing line for the trimmer.

In lawn mowers with a curved bar, which are not provided for a knife, the coils have special two.horned nuts. In such tools, you need to hold the bobbin so that it does not move, and at the same time turn the nut out of clockwise. It is she who holds the whole bobin, which after that is easy to remove.

Direct rods on which you can install a knife have a hole right under the bobin. To remove the coil, a screwdriver is located in this hole, the bobin is fixed. After that, you need to turn the coil on the movement of the clockwise and remove from the unit.

Sometimes clamps on the coil in the form of latches may occur. They must be pressed to disconnect parts of the coil. The option is also possible when the top and bottom of the bobbin are connected by thread. In this case, it is enough to take your hands on the top and bottom, and then twist in different directions until they develop.

Tips for choosing fishing line for a trimmer for grass

Coil. the main component of motorcycles. For a bevel of grass, it is equipped with a special fishing line. This very fishing line for a trimmer can serve you for a very long time, if you do not regret it (fishing line for a trimmer for a trimmer for grass. what you should not save on). Currently, you can find different cutting threads that differ in their cross.section, composition and thickness. Often a fishing line for a trimmer is sold in small or large skeins in specialized stores. If you want your mower to serve you for a long time, approach the choice of fishing line with full responsibility (because due to the wrong choice you can even break your device).

Restring a 2 sided spool on a string trimmer weed eater EASY!!

  • Never choose a thread for “save”. Having bought the cheapest and, obviously, the most low.quality fishing line for a trimmer, you can lose much more. As a rule, the best parameters are indicated on cheap (“Chinese”) fishing lines, but in fact they are completely different. The consequences of buying the cheapest threads can be both a breakdown of the thread and the fact that the lawn mower will fail. If the coil quickly fails, you will have to replace it again, which means you spend even more money.
  • Buy fishing lines only in specialized stores or from sellers, in which you are 100%sure so as not to be deceived.
  • Always check the authenticity of your fishing line. It’s no secret that the goods can fake, and the coils are no exception. If you decide to buy a high.quality brand thread that will last you for a long time, look for special holographic signs or codes on its package. With their help, you can easily check the authenticity of the fishing line.
  • In addition to the advice above, if you choose a high.quality brand for long work, choose a fishing line for a trimmer from German or Japanese manufacturers.
  • If your lawn mower or trimmer for grass has its own production of forests. no doubt, buy them, because the manufacturer took into account all the nuances in advance.
  • Do not forget about the fact that the fishing line for the trimmer should correspond to all the hardware characteristics of your motorcycles as much as possible so as not to cause its breakdowns.
  • It is best to buy 2 or 3 slices of fishing line intended for different purposes at once. One type of fishing line will be more effective in mowing fresh young grass, the second. in mowing stiffly overgrown, and the third will help you demolish all the gross.

When you have already bought a certain type of fishing line, be sure to follow the tips for its operation from the manufacturer. Thus, if you use a thread for young grass for dry.resistant, it will get out of the working condition very quickly, and you will have to buy a new one and replace it again.

How to put, wind and change a fishing line for a trimmer?

To do everything correctly and neatly, prepare a separate cut of the fishing line about 4 meters. The length may vary depending on the characteristics of your thread and the lawn mower itself. To find out how much fishing line you need, you can perform the following simple action: inside the coil, wrap the equipment to such an extent that it and the side protrusion of the coil are equal. At the same time, the equipment should not go out for the side ledges. What happened is the length you need, now you can make refueling. The length of the segment also depends on the thickness of the fishing line. the thinner it is, the more it needs, the thicker, the less.

Here is a instruction on how to correctly refuel the equipment into the tip of your unit.

  • Then you need to take the second end on the other side and go too far. Gently approach him, while ensuring that the retreat is 15 cm.
  • Now you need to find out the direction in which you will wind the fishing line for the trimmer. Ignoring or incorrect execution of this item can lead to your trimmer for grass or lawn mower will not function normally. Inspect the surface of the coil to find out the right direction. In 99% of the coils, an arrow is drawn there, which shows the desired direction.
  • Instead of the gun-wiring pointer, there may be a letter designation (for example, Wind Line), which also indicates the direction. If you are not lucky, and there is no pointer on the coil, it will definitely be on the head. On each head, the direction of its movement is drawn, respectively, you need to wind in the opposite direction from what is indicated on the head.
  • After you have determined the direction of winding, proceed to the process itself. It is necessary to gently wind up (refill) thread on the corresponding grooves-undergraduates. Inside each end there is its own groove, do not forget to follow it. If suddenly they are not, put the equipment in the proper distribution order.
  • Follow the moment when almost the entire thread will be wound. When this happens, place in the side wall (special opening) the part of the part in which the protrusion is 10-15 cm, and then repeat this action with the second end, putting it on the opposite side.
  • Place the drum in its place, and then pull the ends of the thread, thereby taking them out of the walls of the coil. Now you can place the lid in your place.

The process of winding the fishing line on a motorcycle or a trimmer for grass is completed, now cut the ends of the thread, if suddenly their size does not suit you (or you were just mistaken in measurements). You can put on the drum already completely assembled on your unit. Now it can be used. Even a beginner can install a new fishing line for a trimmer on your device, this rarely causes difficulties.

If you are guided by all the advice presented, it will be as simple for you as mowing grass.