How to wind a vein on a motorcycle. How to refuel a fishing line for a trimmer to a trimmer coil for grass

trimmer for grass gasoline stihl how to refuel a fishing line for a trimmer. We change the fishing line for a trimmer in a trimmer (lawn mower)

First of all, to wind the fishing line, it is required to remove the coil (bobbin, spool) from the trimmer for the grass. specific actions will depend on the complexity of the configuration and the type of product itself:

• Small electric trimmers for grass with a working location of the engine and coils in the lower part, as a rule, have side keys on both sides of the bobbin. With the simultaneous press on them, the upper part of the coil, along with the internal contents for winding the fishing line, is disconnected, while the lower remains on the trimmer. It is advisable to analyze the bobbing in an even smooth place, so that the spring does not jump out and not be lost;
• Electric and gasoline trimmers for grass with a curved rod without the ability to install a knife, as a rule, have coils with a special lamb: in such structures, you should hold the spool in a fixed position with one hand, and rotate the fixing bobbin on the bar with a barack’s baracks. After disconnecting the nut, the whole bobin is removed.
• Electric and gasoline trimmers for grass with the ability to install a knife on a straight rod (for example, trimmers for STIHL grass) have a hole. For the immobility of the bar, a screwdriver or another suitable object is inserted into this hole and, with slow rotation, such a mutual arrangement is achieved when the screwdriver enters the hole and the bob is fixed. After that, the coil body is scrolled clockwise (with the left thread) and removed from the trimmer for the grass.

For the second and third cases, the coil, depending on the design, are versed in various ways. In the bobbins with a lamb, lamb is twisted, in the reels with latches, latches-fixers are pressed and one part of the coil is freed from the other. If the halves of the spool are connected by thread, then it is enough to turn them with your hands in the opposite directions until they are completely developed.

Two working antennae

In this type of spools, the number of grooves for winding the fishing line lying on the inside of the coil should be determined:

How to replace a fishing line for a trimmer on a trimmer how to wind a fishing line for a trimmer for a trimmer for grass

For both cases, a fishing line for a trimmer 2-3 m long is taken. In a single.captable coils, the fishing line for a trimmer stretches into a through hole, its ends (antennae) are folded together and aligned, after which they are wound in the back of the rotation of the bobbin on the bar the side. inside the arrow is usually indicated the correct direction of the winding. In the presence of fixing grooves, the ends of the fishing line are threaded in them or hold their free arm fingers, spread into the through hole of the outer half of the bobin, the spool is closed and attached to the bar of the trimmer product.

The difference between the winding of the fishing line in the two-to-dancing coils is that initially a line of fishing line 2-5 m long is folded in half (to determine the middle fold), and the bend loop is inserted into a special groove between the grooves. Both strains of the fishing line are wound each in its own groove, fixing the antennae and assembly of the coil is similar to the option considered above with one groove.

The first implementation of this procedure may seem long and quite time.consuming, but over time and experience, this task will be solved much faster and easier.

The video below will clearly show how to refuel a fishing line for a trimmer to the coil of a trimmer for the grass and correct it correctly. this operation is not a complicated one and, with some patience, will necessarily be crowned with success:

Coil with one working osik

The easiest option and a simple sequence of actions:

• The dimensions of the bobbin and the length of the original factory winding determine the length of the fishing line recommended for winding. 2 5 m.
• One end of the fishing line is inserted into the fixing technological hole located inside the spool.
• The fishing line for the trimmer is wound on the drum in reverse rotation of the spray in the trimmer product direction. as a rule, on the inside of the bobin, the arrow indicates which direction the winding is carried out.
• A small section of the fishing line is left free to output it. it is fixed in a specialized border on the inside of the bobbin, designed to keep the winding when assembling a spool in working condition.
• The left end of the fishing line is passed through the hole of the outer part of the bobbin.
• Half of the bobbin are collected and put on the bar of the trimmer device.

Read how to clean the air filter on the echo trimmer

How to replace a fishing line for a trimmer on a trimmer?

Replacing the fishing line of the trimmer for the grass with step.by.step instructions will even allow the owner of the lawn mowed inexpensive in such matters to do a fairly difficult job.

However, before starting work to replace the fishing line on the trimmer, it is necessary to ensure the safety of work. In particular, it should be taken protection measures against careless or spontaneous inclusion of the lawn mower:

• Exclude spontaneous start,
• Delete the battery (if used),
• Place the tool on a comfortable site for work.

It is convenient to perform work on replacing the fishing line for the grass when the lawn mower lies on the table, and the master, who is performed by replacing the fishing line of the trimmer for the grass, has the opportunity to approach the instrument from any side.

Step Three: The Club of the Head Noner

Stretch the ends of the fishing line through a pair of oval cuts of coil. Replace both goals and a spring (if any in the design) with new elements included in the package. Bend both ends of the fishing line at right angles.

The last technical stroke of the process of replacing the fishing line on the trimmer is to put the cover on the head with subsequent fixation by pressure and slight turnover.

Let each end into the hole, which is at the base of the winding drum. Install the coil in the inner area of ​​the head with an emphasis on the spring. Put the lid, leve on the base and light pressure down with a small rotation counterclockwise, put the cover on the tongues of the latch. This is where the replacement procedure is completed.

Step one: fixing and styling

Fold the end of the fishing line in half. Place the workpiece above the coil on each side of each half of the winding area. Wrap both halves completely around the winding drum. Stretch the fishing line for the trimmer through the loop.

The procedure for preparing fishing line in the field of both wound sections of the drum. The loops are laid in specially made cutouts, after which the winding of the fishing line is performed in each area

Pull the fishing line for the trimmer enough and put the knot in the groove made on each side of the winding drum.

Remove the head of the head of the grass for the grass

At the first stage of disassembly, the head of the head of the grass is removed. On the example of the models of trimmers “Black and Decker” and others, it is usually enough to apply some pressure to squeeze the click-fixer, which are on the side of the head of the head of the head of the head of the head of the body to remove the lid to remove the lid.

Some models of lawn mowers initially include dismantling the head of a trimmer for grass, for which a playback key is used, which is included in the tool kit. The head is usually held by two or three screws, access to which is provided through the side holes of the rear decorative cover.

The head cover, where the coil with a fishing line is installed, is usually held due. It is enough for some effort to squeeze the tongue-thorough and slightly turn the lid, after which the lid is easily removed

At the time of squeezing the tongue-fixer, you need to turn slightly and raise the head of the head of the trimmer for the grass to remove the winding drum.

Read how to put a fishing line for a trimmer on a trimmer for grass correctly

Homemade nozzle on a trimmer for grass instead of plastic coil

To make the nozzle, the author uses a protective casing from a car rack. You will also need a metal washer and an ordinary hexagonal nut (but only with left thread).

We recommend that you read the article: “2 useful tools that can be made from taps”. The tools are designed to work with metal and are definitely useful in a home workshop.

For work, you will need a welding machine and an electric drill, with which in the nozzle itself it will be necessary to drill holes for a fishing line for a trimmer. In time, all work will take no more than 15-20 minutes.

The process of manufacturing the nozzle for a trimmer for grass

First of all, it is necessary to clean the metal at the welding site. Then we take the puck and weld it inside the protective casing (right in the center). We weld a nut to the puck.

After that, using a drill, we drill two holes in the casing on each side. We process them with a file so that there are no sharp edges.

We install the finished nozzle on a trimmer for grass, and fixed with a nut. Then we insert a fishing line for a trimmer into drilled holes.

A universal disc for a trimmer for grass from a diamond disk

If you have an old diamond disk, do not throw it just into scrap metal. From it you can make a universal cutting disc for a gasoline trimmer for grass.

Such a homemade disk has a lot of advantages. Firstly, it cuts dry small grass quite well, which a fishing line does not take for a trimmer. Secondly, it copes with very hard grass perfectly.

And one of the most significant advantages of such a disk is that it saws well bushes and trees, the trunks and branches of which do not exceed in a diameter of 12 cm. The disk is 180 mm at a time cut to 60 mm.

The whole secret of high performance of a home.made disk is in the form and number of cutting teeth. In many ways, it is thanks to the special shape of the tooth that the disk does not burrow into wood, and also does not lose momentum even on a weak trimmer.

The main stages of work

Please note: if you use a diamond disk for an angular grinder, then first of all you need to drill a landing hole in it. The fact is that the disks for the angular grinder have a hole diameter-20-22 mm, and in most trimmers-25.4 mm.

After adjusting the landing hole in size, attach a paper stencil to the disk. The stencil itself can be downloaded from the link.

To exclude damping slots and holes in the disk that serve to cool and remove dust, you will have to reduce the initial disk diameter to 180 mm. Next, we cut out a paper stencil clearly along the contour.

The hole in the center does not need to cut. We clean the surface of the disk of rust and dirt, apply the stationery glue on it, align the stencil exactly through the landing hole and press.

Disk manufacturing process

At the next stage, we cut off the angular grinding of a diamond disk along a glued stencil. Then we remove the remnants of the metal with a cleaning disk, reaching the edge of the stencil.

Along the way, the master cuts out damping slots in the disk. We process the edges with a petal circle and then remove the stencil.

After that, it will be necessary to dilute the teeth. You can do this with ordinary pliers. However, to make the angle the same, the author uses special wiring. Odd teeth need to bend to the left, even. to the right.

Further cutting teeth must be sharpened. The optimal angle of sharpening is 15-18 degrees regarding the center. If the metal is soft, then the ends of the teeth must be hardened. To do this, just heat them with a gas burner reddened and dip in machine oil.

Installation of a new fishing line on the coil of a trimmer for grass

Equipping the coil with a new fishing line is performed in the reverse order. The procedure looks like it is described below, regardless of the model of the lawn mower:

Step one: fixing and styling

Fold the end of the fishing line in half. Place the workpiece above the coil on each side of each half of the winding area. Wrap both halves completely around the winding drum. Stretch the fishing line for the trimmer through the loop.

The procedure for preparing fishing line in the field of both wound sections of the drum. The loops are laid in specially made cutouts, after which the winding of the fishing line is performed in each area

Pull the fishing line for the trimmer enough and put the knot in the groove made on each side of the winding drum.

Step two: winding cutting material according to sections

The next step is to turn the fishing line in a circle of coil, observing caution. It is necessary that each half be filled with “its own” winding, exactly, without intersections. Usually on the hull of the winding drum you can see the arrows indicating the direction of winding. This moment should be borne in mind, filling the reel with a fishing line.

Step Three: The Club of the Head Noner

Stretch the ends of the fishing line through a pair of oval cuts of coil. Replace both goals and a spring (if any in the design) with new elements included in the package. Bend both ends of the fishing line at right angles.

The last technical stroke of the process of replacing the fishing line on the trimmer is to put the cover on the head with subsequent fixation by pressure and slight turnover.

Let each end into the hole, which is at the base of the winding drum. Install the coil in the inner area of ​​the head with an emphasis on the spring. Put the lid, leve on the base and light pressure down with a small rotation counterclockwise, put the cover on the tongues of the latch. This is where the replacement procedure is completed.

Typically, the process of replacing fishing line on a trimmer of a particular model is popularly described by accompanying documentation. Another question is that this documentation is often supplied in a foreign language, since the notorious lawn mowers for the most part are imported products.

Meanwhile, there is a much simpler, more economical and healthy way for human health and nature. putting the lawns of an ordinary peasant oblique in order. Blory of braids for grass:

which is subsequently accompanied by abundantly growing greens, and not by the formation of dryness as a result of the work of a trimmer for grass.

Brief briefing

Z-Zila-publications of materials interesting for society. News of technologies, research, world.class experiments. Social Multi-Tematic Information-Media.

We carry out the winding of the fishing line

Sentlessly completed disassembly of a spray coil without losing its spare parts allows you to go to the main task-winding into a fishing line coil. Technological features of the design of the spool and the number of working antennae determine the sequence of actions.

Coil with one working osik

The easiest option and a simple sequence of actions:

• The dimensions of the bobbin and the length of the original factory winding determine the length of the fishing line recommended for winding. 2 5 m.
• One end of the fishing line is inserted into the fixing technological hole located inside the spool.
• The fishing line for the trimmer is wound on the drum in reverse rotation of the spray in the trimmer product direction. as a rule, on the inside of the bobin, the arrow indicates which direction the winding is carried out.
• A small section of the fishing line is left free to output it. it is fixed in a specialized border on the inside of the bobbin, designed to keep the winding when assembling a spool in working condition.
• The left end of the fishing line is passed through the hole of the outer part of the bobbin.
• Half of the bobbin are collected and put on the bar of the trimmer device.

Two working antennae

In this type of spools, the number of grooves for winding the fishing line lying on the inside of the coil should be determined:

For both cases, a fishing line for a trimmer 2-3 m long is taken. In a single.captable coils, the fishing line for a trimmer stretches into a through hole, its ends (antennae) are folded together and aligned, after which they are wound in the back of the rotation of the bobbin on the bar the side. inside the arrow is usually indicated the correct direction of the winding. In the presence of fixing grooves, the ends of the fishing line are threaded in them or hold their free arm fingers, spread into the through hole of the outer half of the bobin, the spool is closed and attached to the bar of the trimmer product.

The difference between the winding of the fishing line in the two-to-dancing coils is that initially a line of fishing line 2-5 m long is folded in half (to determine the middle fold), and the bend loop is inserted into a special groove between the grooves. Both strains of the fishing line are wound each in its own groove, fixing the antennae and assembly of the coil is similar to the option considered above with one groove.

The first implementation of this procedure may seem long and quite time.consuming, but over time and experience, this task will be solved much faster and easier.

The video below will clearly show how to refuel a fishing line for a trimmer to the coil of a trimmer for the grass and correct it correctly. this operation is not a complicated one and, with some patience, will necessarily be crowned with success:

Removing and disassembling the coil

In order to correctly wind the fishing line for a trimmer to the coil of a trimmer for grass, you must familiarize yourself with the structure of the trimmer head. It consists of a protective casing, a bobbin with a thread, a hull cover, as well as a spring that is present only in some devices.

Starting to disassemble the coil, you must completely turn off/de.energize the device. In this case, the method of work directly depends on the type of head. The first option is to conduct the following actions:

• The user presses on fixers located on both sides of the cover.
• After removing the lid, the spool is extracted. Some models may have a spring, which also needs to be extracted.
• A screw is located in the center of the case, which should be unscrewed with a regular screwdriver.
• When the fasteners are removed, it remains to remove the gearbox from the shaft, gently shaking the case of the product body.

The second option for removing the coil for refueling the fishing line in a trimmer for grass is to tighten the head for the gearbox shaft. To carry out such a procedure, many devices are equipped with a hole into which you can insert the tool. When the screwdriver is inserted, the user can only take up the product body and scroll it clockwise. It is noteworthy that this method, in contrast to the previously described method, differs in the simplicity of execution.

Fishing winding

It is easy to insert a fishing line for a trimmer in a trimmer for grass. To conduct this operation, it is necessary to adhere to a simple algorithm of action. The first step will be the determination of a sufficient amount of expenditure material. To make its calculations, it is necessary to wind a fishing line for a trimmer on a spool so that the resulting coil of the past is less or equal to the diameter of the sides of the structure.

When you have decided on the size of the cord, it is necessary to fold it in such a way that one part of it is 15 cm longer than the other. The winding of the cord’s thread begins with the side dividing the spool into 2 parts. There will be a mount in which you need to insert a thread in half.

Now you need to understand in which direction to refuel a fishing line for a trimmer to a trimmer for grass. To do this, you need to inspect the spool. often a special arrow is indicated on it. If there is no explanatory information, you should find a pointer on a trimmer head, and proceed to wind in the opposite direction. Further actions can be divided into 4 stages:

• Completion of the winding of the cord. To do this, it is inserted into the side groove on the coil. Its second end is attached to the opposite groove.
• The ends of the fixed fishing line are cut. Allowance remains 7-10 cm.
• The seasoned part is placed in the head of a trimmer for grass. To do this, an alternate insert and pulling the thread into the input holes of the structure is performed.
• The thread is pulled out of the grooves. Upon completion of the action, the product cover is fixed using fixers.

After completing the last stage, the garden tool is ready to work. If, after inserting the fishing line into the trimmer for the grass, the device works incorrectly, it is recommended to repeat the procedure by changing the thickness or type of cordial thread. Otherwise, the product may fail.

Choose a fishing line for a trimmer

The fishing line for the trimmer should be strong, stiff and flexible. in the trimmer it serves as a working tool for cutting grass. Flacks of different thicknesses are made. from 1.2 mm to 4.0 mm. Most models are designed for the maximum thickness of the thread of 3 mm. What is the diameter of the fishing line for the grass for grass in one case or another depends on a number of factors.

Depending on the hardness of mowing vegetation:

It is important to consider that too thin thread accelerates the wear of the motor, too rough. will accelerate its overheating and premature failure.

The structure of the cord of the fishing line matters:

• round. universal, most durable, for rough grass;
• curly. for soft plants;
• Twisted with notch. for thin long stems.

Important! Choose a fishing line for a trimmer of the type and parameters that the manufacturer Motokos recommends. Such material will work for a long time and efficiently with optimal loads on the product of the product.

How to change a fishing line for a trimmer on a trimmer

The fishing line for a trimmer is wound on a coil (bobbin), which is located in the body of the head of the trimmer for the grass. First, unscrew the head from the bar with the motorcycle cord and open it the top cover, pressing on the side latches. In some models, the case simply spins.

We take out the coil, clean it from dirt, the remains of the old fishing line. Coils are one- and two-section.

Fishing line winding on a single.section coil

We take 2 m of fishing line, we spread it up to half through a special hole inside the coil. The ends of the fishing line of the same length stick out from both sides. We wrap them with both along the groove of the coil in the direction indicated by the arrow on the case (back to the rotation of the coil on the shaft of a trimmer for grass). We do not wound the fishing line for the trimmer to the end-pieces of 10-15 cm, which will be workers, fix in grooves on board the coil. Fixation is needed so that the fishing line for the trimmer is not unwound when installing it in the head of a trimmer for grass.

We insert the coil into the body of the head, while at the same time we spread the free ends of the fishing line into the holes of the body, set. We collect the head, put it on a trimmer for the grass. Everything, the change of fishing line in the trimmer was carried out.

How to wind a fishing line for a trimmer for a trimmer for grass with a two.section coil

If there are two sections in the coil, put the fishing line for the trimmer in half and insert the fold place into a special groove in the side between the sections. We begin to wind the ends each in its own groove. then everything, as in the case of a single.section coil.

How much fishing line is wrapped on a trimmer for grass? You can wind 2-4 m, depending on the product model. In each case, it is impossible to wind too tight, the thread should have a free move for stretching during operation.

How to change a fishing line for a trimmer on a lawn mower: detailed instructions

In 1971, American entrepreneur George Bollas invented a mower for grass, where a fishing line for a trimmer played the role of a cutting knife. A lot of time has passed since then, the drive has become more powerful, a modern trimmer can easily damage the bark, so that the idea itself was transformed into mowing around obstacles without damage to the very cutting apparatus of a mowing room. For a neat mowing around obstacles, you can have a head with a smaller fishing line, it is easy to change it when moving from mowing large areas to delicate blocking. However, periodically and the cutting tool itself requires replacement. We tell you how to disassemble the head of the lawn mower (trimmer for grass) and wind a new fishing line for a trimmer.

All about the replacement of fishing line with a trimmer head

There are many types of heads that are designed for different types of fishing line. The latter is also available in several diameters: from 1.0 mm to 3.2 mm. At the same time, its section is round (including with a special groove to reduce noise), square, twisted and in the shape of a star.

There are no clear preferences, and this explains the wide variety of forms and diameters in the market. The round shape is usually stronger, but has a worst cutting ability, in addition, when rotation, it makes a characteristic sound. Therefore, sometimes they make an acoustic groove, however, the use of this fishing line makes sense only on battery trimmers, in machines with gasoline and network drive, the sound level of the drive itself practically drowses the sound from the fishing line. The square has a good cutting ability, and despite the fact that such a fishing line for a trimmer is less durable than round, on average it is consumed less. A square fishing line for a trimmer quite easily cuts the shoots of the same Ivnyak up to 1 cm in diameter. The star has the maximum number of cutting faces, mows best and is the fastest consumed.

The next nuance when choosing is stiffness. The fact is that in the production of nylon, a modifier (often maleine anhydride) is added to it, which improves its strength and prevents gaps. However, modifiers are not the cheapest component, they are trying to save on it. Therefore, it seems to be a good fishing line for a trimmer that remained for the winter, in the spring suddenly behaves completely differently. it breaks, stops doing normally from the reel. There is a recommendation to soak a fishing line for a trimmer in the water before work, but I do not see much sense in this, malein anhydride interacts with water, but if it is not enough in the nylon, then there will be nothing to interact. Therefore, it makes no sense to stock up on fishing line for a long period of time, a breakdown or constantly torn fishing line for a trimmer, which also does not want to leave the reel itself, can significantly complicate the work.

How to choose a fishing line for a trimmer for a trimmer for grass

The trimmer for the grass bought in the store is already ready to work. a standard nylon fishing forest is tucked into it. She cuts the grass, but does not cope with work poorly. only young, thin plants quickly fail and mows. She does not take old grass and weeds with stem stems or cuts off at all, wear out quickly. It grabs it for a short time, after which you need to replace the fishing line for a trimmer in a trimmer.

It is not recommended to use a fishing fishing line for a trimmer, it is better to take a special thread with a fiberglass core. It is sold in construction stores. Stop your choice on an option that has a square or triangle in a section. their sharp edges will work like knives.

Fishing line consumption for a trimmer for grass using faceted and reinforced consumables will decrease by 2-3 times, performance will increase by the same amount compared to the circle of round section and fishing line not reinforced with fiberglass.

Purchase material with a diameter not less than recommended by the manufacturer. If the diameter is unknown, you need to look at the size of the holes on the outer body of the mowing head: the diameter of the working thread should be slightly smaller than the hole to pass through it freely.

Buy a sufficient supply of cutting thread (with 2-3 replacements), try to buy different options to compare which one is best in work.

Upon learning how much material is needed for one winding, focus on the length of the forest during the next purchases, so that there are no too short for winding pieces.

To replace the forest on a mechanical spit with your own hands, you need to disassemble the braid head and get the coil on which the working thread is wound.

How to remove a fishing line for a trimmer

To replace a fishing line for a trimmer in a trimmer, remove the head cover. To do this, press the fingers of the latches of fixers located on both sides of the lid, and pull the lid up. Access to the coil will open. After that, pull it out, pulling up the axis on which the coil sits. If the ends of the fishing line stick out from the holes of the head, then lift the coil along the axis and pull the remaining fishing line from the holes of the head. Now the detail does not hold anything and it is easy to remove and remove the remaining working thread.

The coil is divided into two parts by the central partition with a neckline. Different models of cobs differ in size, so you need to check how much you can wind the fishing lines on the bobbin. Its length ranges between 1 and 4 m.

The main stages of work

Now we start installing fishing line. There is a dividing side on the coil, which divides it into two grooves for fishing line.

This side has a groove. We measure the desired length of the fishing line, and then bend it in half (while one end should be 10-15 cm longer).

We catch the resulting loop to the groove. Next, look at the case and look for the Wind Line inscription, next to which there will be an arrow that indicates the direction of winding of the fishing line.

If there is no such inscription with the arrow, then look for the arrow on the head, then wrap the fishing line for the trimmer in the opposite direction.

Fishing winding

At the next stage, we wrap the fishing line for the trimmer, making sure that each end is in its groove. When wound. the ends of the fishing line must be temporarily inserted into the side grooves.

Then we insert the coil into the head, put the lid on top, straighten the ends of the fishing line so that they leave the grooves, and then fix everything on the latches.

Details about how to wrap a fishing line for a trimmer to the head of a trimmer for grass, you can watch in the author’s video. This review is prepared on the basis of video from YouTube Hotsem channel.