How you can cut glass without a glass cutter

Three methods for cutting glass at home

Glass cutting thread

It is quite possible to cut glass without a cutter, using string. First, make sure you have a large bucket of water handy. It must be big enough to hold the glass you need to cut it. First make sure that the glass is clean and dry. Take a good length of thick thread (preferably for knitting, but not necessary) and soak it in alcohol, then wring it out.

How To Cut Glass, Without A Glass Cutter? Here Is How

Wind the thread around the glass along the mowing line of the cut. It is very important that the thread is well stretched; a loose thread will sag and you will not be able to cut the glass evenly. Most likely to ruin it altogether. Light the string, and once it’s all lit up, submerge the glass with the burning string in a bucket of water.

With the glass submerged in water, hit it with something hard where you want to cut. Doing this in water accomplishes two things: it softens the impact and the water reduces the vibration. Eventually the glass should break along the mowing line of the string when you hit it.

Glass cutting wire

Using a wire to cut glass without a glass cutter is also easy. You still need water; however, in this case you need to have a tray in which the glass can lie flat and be submerged in water to a depth of about six centimeters. Start with a clean, dry piece of glass and use a sharp tool to lightly outline the string you want to cut.

Make sure your wire is longer, tie loops at the ends. Put a wooden stick through the loops and pull it tightly against the stick. Heat the wire (you can do it electrically, you can do it with a blowtorch) until it is red-hot. Then press it tightly along the mowing line of the cut.

As soon as you do this and see that the glass is hot, immediately submerge it in water without letting it cool. With a light pressure, the glass will break along the heated mowing line. You can put a stick at the bottom of a container of water directly in front of the heating line and break the glass through it. Then you will get an even and beautiful split.

Glass cutting scissors

It’s amazing, but you can easily cut glass without a glass cutter using scissors. We have already agreed that we have a container of water (it can be a bathtub, an aquarium, or anything, as long as the glass fits in it). Also, so that your hands with the scissors fit under the water and are comfortable to work with.

To cut the glass with scissors, first mark the line of the cut with a marker. Next, fully immerse the glass and simply cut along the mowing line with scissors. You will find that the glass will cut just as if it were thick paper! Perhaps the edges do not turn out very beautiful and jagged, but you can take a sharpening stone and trim it. it’s not difficult.

With a twine

The point of the technique is to first heat the glass to be cut and then cool sharply. Under the action of the temperature difference, it will burst on the scythe line of the greatest contrast. The method is good if you need to, for example, cut a glass bottle or a can.

To do this, you need to soak a woolen thread in alcohol, acetone, white spirit or some other flammable liquid. The rope is wrapped around the intended victim, and set on fire. Then they are sharply cooled by flowing water. A “click” should be heard when successful. If it did not work from the first time, you need to repeat the ritual.

The technique may not work on thick-walled bottles, like champagne Faustpatron. During the experiments it is not bad to have a fire extinguisher, otherwise the results may surprise strongly, up to the arrival of the employees of the Ministry of Emergency Situations and the ambulance.

Fire, water and twine

You make a marking on the glass, limiting the size you need, then soak the twine in flammable liquid, put it on your marking and set it on fire.

You can easily melt the glass into the right pieces with an ordinary piece of string.

As soon as the flame goes out, immediately pour a thin stream of water along the mowing line. The glass is bound to crack at this point. And then everything is trivial: you break off the glass along the crack and grind the edges with an emery. If the crack does not appear, you have to start the whole process over again.

By the way, if you lay the twine figuratively, you can get the resulting plates of quite complex shape. And for cutting bottles this method is simply indispensable. After all, it is difficult to use a glass cutter on a curved surface.

With a little practice, you can cut a given shape of holes. The technology is exactly the same. Only instead of breaking off the cut off, beating out is used:

• Tape the crack along the contour with scotch tape or adhesive tape;
• Knock carefully on the contour with a wooden stick or a cloth-wrapped hammer;
• Squeeze out the cut out piece.

If you do not have the opportunity to mess with the string, you can cut the glass and soldering iron.

How to cut round glass

For example, in the evening young soccer players knocked out your window with a ball. You fill in the hole with glass from some interior room, but it’s a little larger in size. What to do? Glass cutters clearly do not work anymore, running around the neighbors in search. not the fact that you will find. So we have to remember the folk methods of dealing with fragile material.

How to cut glass without a glass cutter? There are several ways to solve this problem. Each of them gives quite good results. We hope that our tips will be useful if the necessary tool is missing or lost among other things.

The method is not universal and only suitable for thin glass, no more than 3mm thick. But almost the easiest. Also allows you to cut not only straight, but also shaped, if you need a specific shape of glass (for example, an insert in the door). Another disadvantage. you can not cut too big a piece.

First of all, take a piece of the same glass and try to cut it. If the glass cracks in the process, it means it is tempered, and this method is not suitable in this case. If all is well, then let’s proceed.

On the glass with a marker you draw the contour you want. Or we use fishing line if we just want to cut off the excess. Some masters advise to cut a template from cardboard and glue it to the glass. In our opinion, not a good idea. First, the paper gets wet, and its rags will interfere with the work. Secondly, there can be problems with glue: water-soluble will not hold the template, and water-resistant will have to remove something from the surface later. unnecessary trouble.

Water is poured into a wide basin. The edge of the glass to be cut is lowered into it. The deeper the piece is immersed, the easier the process will go. it helps the water pressure.

You take strong scissors like tailor’s scissors, dip them under the surface and start cutting. The sensation is more difficult than when cutting paper or cloth. Rather, they are reminded of working with cardboard. It also creates crumbs, so it’s better to cut in protective glasses in case of rebound if you didn’t dip deep enough in the water.

Gloves won’t hurt either, and will be probably even more useful than goggles, because you won’t notice splinters in the water, but they cut strongly.

Many people do not believe that the scissors cut glass, and are very surprised when they try that it is really possible.

In cases where the glass is thick, or so large that it does not fit in the basin, it is suggested to find a soldering iron. Some used a wood burner for the same purpose. And especially poor on tools. even a red-hot nail. Although you will have to spend a lot of time with it to cut the glass, because you have to heat it all the time.

• The glass is laid on a flat surface.
• The line is marked with a cut. Here, by the way, a shaped cut is also available.
• At the very beginning of the line, a neat not too deep notch or file is made on the edge of the glass. You can tear the edge with an angle grinder (only very carefully, on the lowest speed)!) Or even scratch it with a nail.
• The soldering iron is turned on. When it is hot, it is inserted into the notch.
• The soldering iron slowly, without much pressure, is led along the outlined contour. If the line is straight, and you are not sure that you can hold it straight at such a low speed, put a metal ruler and move the soldering iron along it.
• Behind a tool there is a thin crack along the outlined line. To separate two pieces of glass, I put on a thick glove (a kitchen oven mitt will do) and carefully break off the unwanted piece. If you have a shaped cut, it is better to lead the soldering iron as slowly as possible, so that it remains a fraction of a millimeter, and the line is not damaged when separating the pieces.

When using it, it is especially important to observe all fire safety measures, because it involves the use of open flame.

• The glass is again placed on a flat surface. This time it should be made sure that it is not easily flammable.
• The cut line is drawn on the glass.
• From a thin cord with a diameter of 1-2 mm. a piece is cut to the width of the glass. Only natural materials like cotton or linen are suitable, synthetics are not suitable.
• Soak the rope in something flammable. kerosene, campfire lighter fluid, gasoline, lighter fluid. and lay it flat along the mowing line.
• The cord should be lit so that it catches fire along its entire length.
• When the fire is almost out, the cutting line is drenched with cold water. The glass cracks evenly at the burning point.
• If the crack has not reached the end, you can go two ways: wipe the surface and repeat Focus with a string or put the glass on the edge and lightly tap on the mowing line with a wooden or rubber mallet.

Sometimes even masters use this method to create original vases, candle holders, glasses and ashtrays from empty bottles and glass jars. Glass cutters are not very useful for such masterpieces as it is very inconvenient to cut curved surface.

Glassware in the right place is tied with flammable cord, the more so that the temperature drop is created in the case of a bottle is very simple: it is immersed in a bucket of water.

Roughness and small splinters are not uncommon in the place where glass is cut. To eliminate them, take a fine sandpaper, and the cut is sanded to smoothness. This step is especially important if you have constructed an elegant glass from a beautiful bottle: without such processing, there is a great risk of hurting your lips or swallowing an invisible to the eye glass fragment.

So it is quite possible to do without special tools, using one of the folk tricks, how to cut glass without a glass cutter.

Комментарии и мнения владельцев 59

It is not easier to cut a circle with a glass cutter?

Diamond round cutter is in the water, cut it out

Looking for myself a speedometer (working) on the Ants. Maybe someone will propose at a reasonable price?

the problem to find glass thinner than 2 mm, all glass cutters 2 mm the thinnest, in the photo frame is also 2 mm, in short the problem.

The problem to find glass thinner than 2 mm, all glass cutters 2 mm the thinnest, in the photo frame is also 2 mm, in short the problem.

I could not find and cut from a 2 mm piece there are many, and ran out of gas masks)

At one time a long time ago on the nine spherical mirrors cut. Of the large kamazov glass cutter is a good solution. Further grinder, not a single mirror is not damaged.

Back at school I used to cut glass with scissors in water for a flashlight, it was clumsy, but it worked.It’s more likely that it wasn’t cut, but ripped, and the main thing is not to hurry.

Well here Pumped I coped with the task of making a compass Used a suction cup and a homemade rod. The main thing is perpendicularity of the glass cutter to the rod.

You can take it to the edge of the glass. That’s how they do it on the glass cutters. Then you break it off

I cut with a glass cutter in a circle or on the stencil then the edges of the process and normal

Scissors in the water, do not cut too much at once. it will burst

Come on )))P. S. I’m sorry if the picture hurt my emotional equilibrium

And not a tourist? The speed is the same and the steering wheel is similar

You can cut glass with scissors (slowly), ! but do all this by dipping it under water (for example in a bucket) !

А. Buy a similar sized gauge at the market and remove the glass.Б. In a basin of water, use the scissors to cut the corners of the square, then trim on a wet sharpening stone.

I cut it in oil. In water, not so much.And I cut it with metal scissors.

You must have read the book of advice of tsarist Russia. So there it was about the floor of antimony glass, it was really cut with scissors. You can’t do that to modern glass.

No, modern glass. Yes, and someone above has already posted a video.

You have to know how to do it. Cut isn’t quite the right word, you practically have to paint in pieces equal to the thickness of the glass. and the water just keeps the shards from flying off. Did it a few times, back in the days of the Soviet Union. It’s important to feel.

It’s not working? It works. That’s how we used to cut out bicycle and moped mirrors when we were kids. A basin of water, tailor scissors stolen from parents, a luckily cut mirror, and not very luckily received pindulins from parents.

works fine, on a business trip, broke the speedometer glass, no place to get it, with scissors the second time, no problem

А. Buy a gauge of similar size at the market and take out the glass.Б. In a basin of water, use scissors to cut off the corners of the square, then use a wet sharpening stone to level it.

Easier on the diamond wheel! It is very well sharpened!

)) it is easier in the workshop, at the professional and glass dust will not have to breathe!)

Nowadays glass cutters equipped with diamond and carbide cutters are able to cope with practically any glass-cutting job. But a few decades ago this tool was not so available, instead of it were used other, alternative methods. It is useful to know them because, for one reason or another, you might not have a glass cutter handy, and it will be necessary to cut a certain size of glass as a matter of urgency.

Working with a soldering iron

How to cut glass when you have a soldering iron handy? The material is placed on a flat surface and with the help of a file make marks on the edges. A ruler was attached to it and the soldering iron was touched with an indentation of 2-3 mm from it. You have to heat each place so that the glass cracks. Run the soldering iron across the entire cut so that it is quite straight.

Break the glass with special tongs or lay it on the edge of the table. The break will go exactly along the groove when glued along the cut with adhesive tape or wet newspaper. If the item needs to be inserted into a frame, you will have to cover the place of installation with putty or strips of rubber. It is attached to the frame and closed with glazing bars, under which a rubber seal is placed.

How to cut glass without a glass cutter? 3 practical ways

Life can sometimes puzzle you with a completely unexpected problem. For example. how to cut glass without a cutter, if you suddenly do not have it handy, and the work must be done urgently? Not everyone has it on the list of necessary tools. You do not want to buy it for disposable work. once in a lifetime to cut a new mirror, and then the tool will lie idle for years without use.

For example, in the evening young soccer players knocked out your window with a ball. You cover the gash with glass from some interior room, but it is slightly larger in size. What to do? Glass cutters clearly no longer work, running around the neighbors in search. not the fact that you will find. So, we have to remember the folk methods of dealing with fragile material.

How to cut glass without a glass cutter? There are several ways to solve this problem. Each of them gives quite good results. We hope that our tips will be useful if the necessary tool is missing or lost among other things.

The method is not universal and is suitable only for thin glass, no more than 3 mm thick. But it is almost the easiest. Also allows you to cut not only straight, but also shaped, if you need a specific shape of glass (eg, an insert in the door). Another disadvantage is that you cannot cut too much of it.

First of all, take a piece of glass of the same thickness and try to cut it on it. If the glass cracks in the process. then it is a hardened glass, and this method is not suitable in this case. If everything is in order, then proceed.

The necessary contour is marked on the glass with a marker. Or a fishing line if you just want to cut off the excess. Some masters advise to cut the template out of cardboard and glue it to the glass. In our opinion, not a good idea. First, the paper gets wet, and its rags will interfere with the work. Secondly, there may be problems with glue: water-soluble will not hold the pattern, and water-resistant will then have to remove something from the surface. an extra hassle.

Water is poured into a wide basin. The edge of the glass to be trimmed is lowered into it. The deeper the piece is immersed, the easier the process will go. it helps the water pressure.

We take strong scissors like tailor’s scissors, plunge them under the surface, and start trimming. It feels more difficult than cutting paper or cloth. It’s more like working with cardboard. It also produces crumbs, so it is better to cut in safety glasses in case of rebound, if you do not deeply enough immersed the glass in water.

Gloves won’t hurt either. And they are, probably, even more useful than glasses because you can not see shards in water but they cut very strongly.

Many people do not believe that the scissors can cut glass, and are very surprised after they have tried it, that it is really possible.

In those cases when the glass is thick or it is so big that it does not fit in the basin, it is suggested to find a soldering iron. Some have used a wood burner for the same purpose. And especially the tool-poor even used a red-hot nail. Although with it you have to waste a lot of time cutting the glass because you have to heat it all the time.

• The glass is placed on a flat surface.
• The cut line is marked. Here, by the way, shape cutting is also available.
• At the very beginning of the line, on the edge of the glass is made neat not too deep notch or file. You can tear the edge of the angle grinder (only extremely, carefully, on the lowest speed!) or even scratch it with a nail.
• The soldering iron is turned on. When it is hot, put it into the notch.
• Slowly, without much pressure, guide the soldering iron along the outline. If the fishing line is straight and you are not sure if you can draw it straight at such a low speed, put a metal ruler on it and move the soldering iron along it.
• Behind the tool, a thin crack appears along the outlined scythe line. To separate two pieces of glass, put on a thick glove (a kitchen oven mitt will do) and carefully break off the unwanted piece. If you have a shaped cut, it is better to lead the soldering iron as slowly as possible, so that a fraction of a millimeter remains to be broken, and the fishnet is not damaged when splitting the pieces.

When using it, it is especially important to observe all fire safety measures, since it involves the use of open flame.

• Again the glass is put on a flat surface. At this time it is necessary to make sure that it is not easily flammable.
• A cutting line is drawn on the glass.
• From a thin cord with a diameter of 1-2 mm. Cut a piece to the width of the glass. Only natural materials such as cotton or linen are suitable, synthetic is not suitable.
• The rope is soaked in something combustible. kerosene, campfire starter, gasoline, lighter fuel. and laid flat along the mowing line.
• The fishing line is set on fire so that it catches fire along its entire length.
• When the fire is almost out, the cut fishing line is drenched with cold water. The glass is cracked exactly at the place of burning.
• If the crack has not reached the end, you can go two ways: wipe the surface and repeat Focus with a twine, or put the glass on the edge and lightly tap the mowing line with a wooden or rubber-coated hammer.

Sometimes even craftsmen use this way to create original vases, candle holders, glasses and ashtrays from empty bottles and glass jars. Glass cutter for the creation of such masterpieces is of little use because it is very inconvenient to saw the curved surface.

Glassware in the right place is strapped with flammable cord, the more so, the temperature difference is created in the case of the bottle is very simple: it is immersed in a bucket of water.

Roughness and small splinters often remain on the place of glass cutting. To eliminate them, a fine sandpaper is taken, and the cut is sanded to smoothness. This step is especially important if you have constructed an elegant glass from a beautiful bottle: without such treatment there is a great risk of hurting your lips or swallowing an invisible to the eye glass fragment.

So it is quite possible to do without special tools, using one of the folk ideas, how to cut glass without glass cutters.

• How to remove old paint from window frames? 3 practical ways
• What’s the best way to insulate a brick house from the outside? Consider the ways and methods
• How to clean a gun from assembly foam? A few simple methods
• How to cut a mirror with a glass cutter? Almost everyone can do it

What must be known about tempered glass before cutting it?

Tempered glass is characterized by great strength. It is used for glazing balconies, loggias and skylights. This material is used to create a variety of furniture and translucent structures. If you need to cut the hardened glass, you need to prepare carefully for this process, carefully studying all the features of the event.

The first thing to know about tempered glass is its characteristics. In essence, it is a thermally polished material. Unpolished and polished sheets of glass are used for its manufacture. The glass is tempered directly in tempering furnaces designed specifically for this purpose.

Glass cutting should be done on a flat surface with a cloth or a piece of paper.

This machine heats glass to 680 degrees. At this temperature, there is a partial softening of the material. The glass is then rapidly cooled by a uniform flow of air. The surface layer cools down first. The inner glass, on the other hand, is subjected to residual compressive stresses in the process. This is what makes tempered glass so heat-resistant and mechanically strong.

Averaged data show that tempered glass is about 6 times stronger than conventional material. It is quite difficult to break it without a desire to do it intentionally. Even if a tempered glass object breaks, the material turns into a multitude of small pieces without sharp edges, so that it is impossible to hurt yourself on them as it could happen with ordinary glass.

All work steps, including edge processing, are carried out in-house. This is done before sending the glass to the furnace for hardening. After all the related activities have been performed, the hardened material is not subject to any mechanical effects. If you want to change anything, you must first anneal the glass.

The scope of application of this material is quite extensive. Tempered glass is popular for building and glazing door and window apertures, it is also used for shower cabins, furniture, and other constructions. So if you are planning to make durable and reliable glazing, but do not have the skills to cut tempered glass, study the proposed instructions in detail and do everything in accordance with the manual. If you think that such a process is too difficult for you, it is better to immediately contact the services of a specialized company to order products of the right shape and size, with all the required cutouts and apertures.

How to Cut Glass Without a Glass Cutter

Some glass-cutting experts advise to cut glass with a woolen thread, which is put or which is wrapped around the supposed place of cutting glass, then it is moistened with kerosene, and then set on fire. After the thread burns off, the glass is dipped in cold water, where it falls apart into the right halves.

You can try to cut glass with an angle grinder, using a fine-grained wheel, but it must be done very carefully, following all safety precautions.

Properly cut glass without a glass cutter:

To cut the glass without a cutter you can use a nail or any sharp object. It’s just that it takes you a lot longer.

There are also diamond-coated ladies’ saws, but they are only good for one time.

After you spend one of these items on the glass, you need to lightly tap the bottom of the place of the cut.

They say that you can cut glass with scissors underwater.

And you can also attach some rope, wet it with kerosene, light it and put it in cold water, the excess will come off.

True, I have not tried any of the methods myself.

cool ways, especially with scissors! 4 years ago

My husband cut glass with an angle grinder, it works, but you have to be very careful and on an even surface.

I used a soldering iron.but you have to be careful.

If the glass is thin you can easily cut it with scissors, pre-cut it in water. The two-piece cuts like butter, I’ve tried it myself. The three is already difficult to cut, but I can still cut it very carefully. If the glass is molten, unfortunately you can not cut it with anything, not even a glass cutter.

Preparing the glass and tools for cutting

The process of preparation will depend on what kind of product you will use for cutting. If the product is new, it’s enough to wipe it with an old newspaper.

Glass that has already been used will have to be worked on:

• It has to be cleaned well. You need to use a special glass cleaner.
• You need to degrease it. Kerosene is used for this.
• It should be dried indoors.

In addition, it is necessary to prepare the cut for cutting. There is no way to avoid waste-free production when working with this material. Especially if you intend to cut a shape of irregular shape. To minimize waste, make a billet and use it to cut the shape. The resulting scraps should not be thrown away, they can be useful for creating other products.

For cutting it is necessary to use special tools:

• Diamond glass cutter. Used at home glass cutter with a beveled blade. It can cut up to 10 km. This glass cutter requires more frequent sharpening.
• Roller Glass Cutter. It is an element that holds from 1 to 6 rollers, made of a durable cobalt-tungsten alloy.
• Oil glass cutter. The structure is similar to a roller tool, differs in the container with oil. From the container, the liquid is applied to the surface. Perfect for working with thick glass.
• Tools for cutting circles and ovals.

You can also cut glass pane with scissors.

The above techniques have the right to life and produce good results with skillful handling. If you are inexperienced in glasswork, you might not get a straight chipping the first time. Before you start processing the base material, we recommend first to get a hand on unnecessary splinters. If you want to get a quality cut without a lot of practice, it will be better to buy a roller or oil glass cutter. article from the rubric Rating

Hand Tools DIY

Save this page to your social network. network and return to it at any time.