How to cut a laminate with a corner grinder. Kryzuvka for metal and saw on wood

What disk to saw a laminate with a corner grinder

In the process of laying the laminate, there is a need for its trimming, and then the question arises: how to cut a laminate, corner grinder, jigsaw or disk saw (circular)? And which disk for cutting laminate to choose? And here, perhaps, the question of what to saw is the most important. Many newcomers are trying to trim the laminate with a corner grinder, the benefit of special wood wheels for Bulgarians is on sale, but it is wrong, too much turnover, it is very dangerous.

Cutting laminate Circular cutting laminate with circular

No, theoretically, a laminate can be cut with a corner grinder, especially if the corner grinder has a revolution regulator, which happens infrequently. Just adjust to minimum turns and install a wood disk. But most of the Bulgarians, especially inexpensive, such revolution regulators are absent.

I usually cut the laminate with a disc saw, installing the disks according to the laminate, I usually choose the same manufacturer as the saw, in this case, I have a “Bosch” circular. However, you can do others, look at the marking, usually on the disks it is written. “by laminate”. The laminate disk usually differs from the standard tree in smaller teeth, for a “clean” cut.

Disk saw a pilepid pile in laminate

You can also saw with universal wood drives, it is just not very convenient, and the cut will turn out thick and uneven, but for lack of disks in the laminate, and this option will do.

Actually, since the laminate trimming is carried out at the lamellas, which will be located against the wall, followed by covering the cuts with a skirting board, that is, will not be visible. Therefore, about the “purity” of the cut, I, as a rule, do not bother.

And already according to the diameter of the disk. this must be selected for your saw, you can read in the instructions with which disks your saw works.

Laminat cutting with a jigsaw

As for the electric jigsaw, it is also convenient for them to cut a laminate, perhaps this option is even preferable. For a jigsaw, select files with small teeth.

Guillotine for cutting guillotine laminate for laminate cutting

There are also special guillotics for cutting laminate, but if you have a one.time job, then it makes sense to buy an expensive device (about 10 thousand. rubles) is unprofitable.

How to cut a laminate at home without chips

Ламинат можно резать пилками, дисками, резаками и даже ножом. Правильный инструмент значительно ускорит время при укладке. Тем более стоимость его не так велика. И лучше потратить 20-30 долларов на тот же лобзик, чем пилить обычной ножовкой. Хотя кроме лобзика еще есть много вариантов.

Today we consider all the ways. You will learn how to cut a laminate best and from which side. We will also talk about how to saw lamellas correctly and without chips.

Perhaps you already have some kind of tool. Most often it is a simple saw, angular grinder or jigsaw. For them we will choose the right wheels, and good files.

When choosing a tool for cutting a laminate at home, it is important:

• Its speed and convenience when cutting. Pulling a heavy machine makes no sense;
• Pure and even cuts without chips and bullying at least garbage. It is clear that all the slices will go under the plinth. But you can lay the laminate not only on the floor. Often chips can spoil the appearance. Or you need to make a joint of tiles with a laminate without a rocking;
• Whether the tool is useful after laying. We take what will not gather dust in the closet at a reasonable price (if there is nothing to cut);

How to cut a laminate with a jigsaw. the right files solve everything

Most often recommended to saw lamellas with an electrician. In general, a jigsaw is a universal device. The tool is always needed on the farm. And it is not expensive. The cheapest device is easy to find for 20.

It is light and mobile, you will quickly learn to work with it. This is how to cut a laminate is really convenient. Here is the main solid hand (so as not to drive to the sides) and the selection of files. Which side of sawing will we figure out further.

How to cut a laminate with an electrician:

• It is very important what pieces to cut laminated boards. There are special on sale. for laminate. But if you did not find them in trouble. So that there are no chips on the front side, make markings and cut it on it. And then we just use a file with teeth that are directed down. It is she who provides almost the perfect cut. All chips will be on the bottom of the lamella. But you have only a saw with teeth at home. In this case, we make markings and saw on the back side. That’s the whole secret. Some still use metal files.

• You need to cut the laminate in another room. There will be a lot of sawdust. By the way, they are scattered differently depending on the file. Cloves up. sawdust up and vice versa. This is that sometimes you need to put on glasses;
• You need to hold a piece that we cut off. Since at the end of sawing it can tear a piece of coating from above;

A jigsaw can be sawed laminate not only in length and width. You can easily perform curly cutting with rounded corners. For example, make a beautiful drank for a pipe.

Is it possible to cut a laminate with a corner grinder, it is also an angle grinding machine (angular grinder)

If you have a corner grinder, feel free to use it to cut the laminate when laying. She can cut almost everything in the world. This tool is always at hand with a good owner. You can find a new corner grinder for 25 (this is the simplest). It is important to choose the desired disk here. Ordinary abrasive (black) is not suitable, the board will burn and smoke. Drinking a laminate with a corner grinder for a beginner without preparation is more difficult. You need to get used to the tool.

How to cut a laminate with a corner grinder. important nuances:

• We immediately determine which disk to saw. It is best for cutting to be the same for a tape disk (by ceramics, porcelain tiles). Make markings on the front of the board and immediately cut. It will turn out a very even and clean cut, no chips. It is advisable to hold the sawed part of the board;
• Corner grinder saws very dusty. If sawdust flies during the cut, then fine dust here is flying. She settles on Lameli herself and throughout the room. Therefore, it is better to cut a laminate to go outside or on the balcony.

Is it worth cutting the laminate with a regular saw

A simple wood saw of course will cut a laminated board, but. She has large teeth. there will be chips and torn areas if you saw it from the front side. You can try to saw the planks of the laminate with a hacksaw for metal. Her teeth are much smaller and thinner. In any case, using a simple saw or hacksaw is a long, tedious and very difficult task.

over, compressed boards are very dug for the tool. The fact that the jigsaw or angular grinder does in a couple of seconds, you need to suffer for 1-2 minutes with a saw. After the cut of several lamellas. hands and all sweaty. And also half the room is not laid. Now imagine that you have sipped crookedly. The novice master does not always manage to cut properly the first time.

Which saw is better to use? If you need the perfect cut without chips, we buy a hacksaw for metal. Its price is 5-10. It is not a fact that one hacksaw is enough to lay a laminate in the whole apartment.

Circular saw/machine or circular

The cheapest circular, meaning a saw, costs from 40. Buying it specifically for a cut of laminate when laying it is pointless. And drag a huge machine into an apartment is also not an option. If you are a happy owner of this tool, you can safely cut a laminate. To do this, use a metal disk. The newcomer will have to learn how to use the circular. This is not safe, even experienced craftsmen sometimes get injuries.

Features of the use of circular saw:

• Mark and cut on the front side;
• Reliably fix the workpiece on a flat surface upwards. It is to fix it, and not so that one holds, and the other saws;
• If you have a circular machine. marking and cut also on the side with a pattern;
• In the case of using the machine, the laminate board is not fixed. She is neatly conducted to disk. Be sure to use glasses so that large sawdust does not get into the eye.

Special cutter, guillotine for laminate

The home master definitely should not purchase this expensive tool. over, he can cut a laminate along it very badly. For 40-50, which are asked for it, it is better to buy a more expensive electrician. The device consists of the base and a handle with a blade for cutting lamellas.

The principle of its work is quite simple. Put the plank of the laminate on the base and lower the handle down. However, when working with this tool, there are features. Here they are:

• As already mentioned above, this guillotine does not cut well along;
• Cuts off very not carefully, the cut piece looks like a stub. Even the sharp blade of the Rezak literally tears laminate;
• You need to make a lot of effort, and the blade is quickly stupid. Hands are very tired. A thick laminate of more than 8 mm may not cut;
• Used only to cut the laminate. T.e. In the farm, this device will no longer come in handy. So, for home conditions is not suitable.

Cutting brick

Brick is a common material in construction. It is often required to fit in size, carrying out repair work in domestic conditions. At the same time, cutting bricks with a corner grinder is a very common operation. It will require, in addition to the working power tool with cutting disks, there are also such devices:

The whole process of cutting brick blocks is accompanied by significant dust formation, so you should take care of protecting the respiratory system and eye from dust. To do this, use glasses and a respirator or a continuous mask. Hands must be protected gloves.

To work with virtually no dust, it is necessary to regularly water the site of the cut with water.

The cutting process itself consists of several stages:

• applying with a chalk or pencil of the marking lines using a ruler or a square;
• Cutting bricks, in which the circle should pass near the applied line to provide the required size of the block fragment.

It is recommended to lay the board to the sawn brick so that it is more convenient to work and not damage the flooring. When cutting a brick unit, pressing on the power tool is not required. Simitable attachment of effort enough. When the work is carried out using the circles insufficient to fully saw the diameter, the cut is made along the marked perimeter. The excess is beaten off with a hammer, and then polished.

Labor efficiency and the quality of the final result can be increased by the use of a special bed. It allows you to reliably fix the angular grinder and brick block. At the same time, cutting a brick becomes possible not only along or down, but also at different angles. This installation is shown in the following photo.

To cut the brick immediately, without turning over, you should use circles with a 230 mm disk diameter. It is easier to process sections of the cut if the nozzle size is 125 mm. If you cut blocks in such a relatively small disk, then the quality of the result will be largely determined by the skill of the cutter. The work time will also increase, labor productivity will decrease.

Brick sawing disks

Cutting circles for cutting brick blocks should be selected correctly. Suitable discs are divided into two categories:

The main advantage of the first group of circles includes their relatively low cost. But abrasive nozzles often have to be replaced due to their failure.

Abrasive discs can break through during work or crack, deform. this is the danger of their use.

Diamond circles are considered the best option for cutting brick blocks. They are made of steel of durable brands. Such nozzles are characterized by a long service time. They are safer than abrasive analogues. Among the diamond discs, several varieties are distinguished:

Products of the first group are characterized by a low price. But when used, they wear out faster and warm more than the rest of the analogues. Segment discs are distinguished by the best removal of brick particles from the cut. They also slowly heat up. This variety is a good option when cutting is carried out in a dry way.

A group of nozzles with a gear edge has the best strength characteristics among other varieties. They are used both with a humid cutting method, and with dry. They differ in a long service life.

How the laminate works

Laying the laminate only by whole parts is almost impossible. Laminate lamps are most often made rectangular shape. On the surface of the planks there is a thin film made of resin, which protects the laminate from various kinds of influences and damage. Under the protective layer is a layer with a shade, where the formation of a picture goes, which externally looks like a tree of various types.

Next is a layer of wood-based stove, which increases stiffness indicators. The latter is a layer of melamine, thanks to which the laminate is resistant to moisture. As a result, it turns out that in thickness such a coating will be about six to twelve centimeters. If you saw such products, then it is very important to carefully make the edge. Otherwise, curved chips may form, which will need to be compensated by valuable centimeters of the coating. It may also be necessary to replace the elements with a malfunction with new.

In order not to throw away valuable pieces of coating, which is quite expensive, it is better to prepare tools in advance that will make it possible to make even sections. Thus, you can protect yourself and immediately styling without spending additional resources.

It is important to make only even sections. otherwise you can greatly ruin the coating, which will affect the expenses

Using a hacksaw

If there is no angular grinder or electric jigsaw at hand, you can cut the laminate with a hacksaw. You can use not only the tool that is designed to work with the tree. The metal hacksaw is also suitable for. It should be noted that the pruning process will take a lot of time.

Before starting work, you need to carefully inspect the tool. If the teeth of the hacksaw are large, then the appearance of chips cannot be avoided. It is also worth considering that the cutting part of the hacksaw on the tree is quite rough. Therefore, it is better to use a hacksaw for metal. It is advisable to grate the cutting part of the hacksaw paraffin.

Before starting work, as in previous cases, it is necessary to fix the laminate bar on a solid surface. Specialists do not recommend crushing the hacksaw. The cut will turn out to be uneven.

Using a hacksaw

If there is no angular grinder or electric jigsaw at hand, you can cut the laminate with a hacksaw. You can use not only the tool that is designed to work with the tree. The metal hacksaw is also suitable for. It should be noted that the pruning process will take a lot of time.

Before starting work, you need to carefully inspect the tool. If the teeth of the hacksaw are large, then the appearance of chips cannot be avoided. It is also worth considering that the cutting part of the hacksaw on the tree is quite rough. Therefore, it is better to use a hacksaw for metal. It is advisable to grate the cutting part of the hacksaw paraffin.

Before starting work, as in previous cases, it is necessary to fix the laminate bar on a solid surface. Specialists do not recommend crushing the hacksaw. The cut will turn out to be uneven.

Laminate cutting tools

If you choose tools for cutting laminate, then you should take into account a number of features.

• It is important that the tools are convenient to use. In many ways, convenience depends on the ability to use the tools and preferences of people.
• If the tools are low and ergonomic, then with their help you can do all the work much faster. When conducting repair work, time is a very valuable resource.
• An important nuance when choosing a tool and a sawing is that the cut should be even, without any cracks and chips. Nevertheless, you do not need to focus on this nuance attention, since some kind of irregularity can be hidden under other elements.

Electric jigsaw

It is very simple when using the tool that allows you to cut the lamellas is a regular electric jigsaw. The jigsaw functions at very fast speeds. This means that you can make all the cuts very smoothly. An important nuance during the work of the jigsaw is the choice of a suitable tool for the tool. Today, most of these tools have in their set files for such coatings that can be easily replaced. If comparisons with other types, then they have a different shape, size and position of the teeth. One way or another, if there are no special files, you can also use standard with small teeth, which are used to cut metal products.

It is quite simple to cut the laminate with an electric jigsaw. this does not require special skills, you only need to observe safety precautions

In order not to damage the layer with the image, make notes and all actions with the tool is necessary from the inside. It is better to put the coating on the table or stool so that the cut part of the panel is suspended. Firmly fixing the element with the hand, you need to quickly walk on the planned cut line.

Bosch has laminate cutting tools. Solutions from this German company are great for work. The assortment has devices for cutting both straight and figurators. There are also tools to make narrow cuts.

Special files for an electric jigsaw from the company are presented in a wide range. So, the company has a model in which the cloves are located on the reverse side. Such a saw will not harm the coating, and the cuts will be even and smooth.

It is worth using special jigsaw files to cut the laminate

In addition to cutting the laminate, the tool can be used for work with plywood, wood-bruise and wood-fiber slab.

There is also a model that is perfect for the curly cutting of a laminate or other wood coating.

• A narrow saw will make the cut more neat.
• If you need to make a cut as soon as possible, then the tool with large teeth will be an ideal solution, but the risk of damage to the material will increase.
• Always use proven equipment with all the necessary certificates of authenticity.

Step.by.step instruction of laminate cutting using an electric jigsaw

Guillotine

To incite the necessary pieces of laminate panels, you can use the guillotine. If we draw analogies with a jigsaw, then the guillotine has a device with a mechanism. Outwardly you can make a comparison with large scissors. Such a device will not make noise, and with the help of guillotine it is easy to cut across the panel. True, to purchase a tool only in order to make repairs in one room, you should not. The guillotine will be more useful for people who, on a constant basis, lay coatings on the floor. specialists. It will be better to borrow such a tool for the time.

You can use a special guillotine that will help to cut off the laminate evenly

A circular saw

You can cut it, and using professional equipment. circular saw.

Cope well with the task and circular saw

It is important to know that if you use a circular saw, then it should have a special.purpose disk suitable for work with metal products. In addition, to wield a circular saw, you need to have a certain level of skill.

When working with a circular saw, the panel is placed up and firmly fixed. You need to be very careful when working with such a tool. Always remember safety measures when working with equipment that can harm a person. Always fasten your sleeves and watch your hands.

The most budget circular saws will cost about forty dollars. Purchase such equipment to make a cutting coating from a laminate does not make sense. In addition, it is quite overall, and bring it to the house is not an option. If there is such a tool in stock, then you can produce all the manipulations with a laminate. It is necessary to use a disk for work with metal products, however, it is worthwhile to have experience so as not to damage the product and not harm your health.

Nuances for work with “circular”.

• You need to make markings and make cuts on the front side.
• It is important to firmly fix the part on the flat surface with a pattern upward. It is important that the lamella is installed correctly, and not so that one person holds it with his hands, and the second makes a cut.
• If there is a machine with a “circular”, then everything is done in the same way as described above.
• If the machine is used, then the laminate is not fixed, but simply carefully brought to the cutting disk. It is important to use protective equipment and protect your eyes.

It is important to observe safety precautions when working with a circular saw

Milling mill

For cutting laminate, you can also use a milling cutter. It is unlikely that each person has such equipment at home, however, specialists who are engaged in work with furniture products are usually always available. Using such a tool can make an ideal incision.

Coating types

The choice of tools for cutting laminated panels largely depends on the type of planks used. If the flooring is supposed to be done independently and without the help of specialists, it is better to pay attention to soft types of laminate.

At home, it is easy to cut a soft cork or two.layer vinyl laminate. Such varieties of laminated panels are characterized by high strength and moisture protection, as well as masonry speed.

To cut this type of lamellas, you will not need a special tool, for this it is enough to equip yourself with a regular ruler, a pencil or pen and a construction knife. First, the fishing line for the cutting trimmer is circulated with a pencil or handle, and then it should be drawn with a knife. After that you just need to bend the canvas. If you need to make a curly incision, then you can use large scissors for this action.

However, for cutting other types of multi-layer panels, including high-strength wood-combustible or wood-based plates, it is necessary to choose more serious tools.

What to use at home?

When choosing a tool for cutting laminated panels, there are several factors that should be taken into account:

• The tool should be easy to use and not cause discomfort. It depends more on personal preferences and behavior.
• Compact and light objects are much easier and faster processed, and every minute in the account.
• Another important point is that with the chosen tool you should get a uniform incision without chips and cracks. However, there is no need to focus too much on this factor, since minor irregularities will be imperceptibly hidden under skirting boards.

Having familiarized yourself with the main characteristics, you can proceed to a more detailed study of the tools for sawing the laminate.

One of the simplest tools for cutting the planks electric jigsaw the device is light, and even a teenager or girl will quickly cope with it. The puzzle works at high speed, so the cut is done carefully. One of the important factors when using this device is the correct choice of puzzle. Modern models are usually equipped with special variable files for working with laminate. Other files differ in shape, location and size of cloves. However, in the absence of special devices, narrow files with small cloves are also suitable for cutting metal products.

In order to avoid damage to the decorative side of the brand and all manipulations with a jigsaw with the panel should be performed on the wrong side. The fabric should be placed on the table or chair so that the cut.off piece of the strips hangs. Strongly pressing the panel with your hand to the table, you must quickly move the jigsaw along the site of the jigsaw.

For cutting the necessary pieces of laminated panels, guillotines are quite suitable. Unlike the previous device, the guillotine has a mechanical device. In appearance, it can be compared with large scissors. This cutter is quiet, simple and accurate in operation. Using it, the easiest way to cut off the laminate, but buying a cutter for repairing an apartment will be inappropriate. Such a device is suitable for those who are professionally engaged in the laying of the floor, so it can be found in temporary use from familiar repairmen.

How to choose the right tool

Here it is worth taking into account two defining circumstances:

For example, what should be sawing a laminate at home? It makes no sense to purchase an expensive powerful electrical equipment, so much a laminated board will help to perfectly cut a machine with the name: Guillotine. When finishing by a commercial laminate of the floor of a large area in the office, it makes sense to choose a circular saw.

Sometimes there is a need to increase the technological gap in the wall left by insufficient size by mistake. Than then cut the laminate against the wall to increase the size of the gap? An example of using an electrician to solve this problem is given in the video:

Whatever the tool you choose, not everything depends only on it. It is necessary to act carefully, slowly, with attention making measurements and applying marginal lines for trimming. You should not make an effort to the board too much during cutting, so as not to break the edge. We wish you good luck!

In fact, it turns out that for many it is much easier to assemble a design of laminated panels than to fit these panels in the right size. And all because most people who are trying to make repairs do not know what to saw laminate.

In order to understand this, it would not hurt to understand what layers the panel consists of.

About the laminate

The processing of any material requires any special tools suitable for this composition. You won’t cut ceramic tiles with a hacksaw, and cut metal with glass cutter, because even the best cutter for one structure will be completely useless for the other.

That is why we will figure out what. And also see photos and videos about laminated panels.

What is Laminite made of

• The lowest layer, which is marked in the figure, consists of unrefined or made paper. It is a reliable obstacle for moisture, which can come from the main sex. Sometimes an additional for sound and thermal insulation is added to the paper, but this happens only in individual collections and the price of the material changes significantly from this.
• The thicker layer of the laminated panel is indicated by the number 2, it is made of high.fiber stove of high density (HDF) and the quality of the products largely depends on its thickness. The castle is cut into this layer and the thicker the wood.fiber slab, the higher the locking of the lock, therefore, the groove is deeper and the connection is denser (lack of clearance).
• The number 3 in the figure indicates a decorative layer of paper, on which a certain drawing is applied. Since the drawing can display many materials, the panels can imitate various wood of wood, wooden and ceramic parquet, stone, sand, marble and the like.
• The highest, fourth layer, consists of acrylic or melamine resin. Through it almost without interference, the decorative design of the panel is clearly visible. Depends on the thickness of the protective upper layer. And, therefore, its belonging to a commercial or household category (classification of the domestic (non.profit) laminate begins with the number 2, and the commercial one from the number 3).

Coming of laminated panels

• If there is an instruction on what is better to cut a laminate, then it probably looks more like advice, not instruction. After all, if you pay attention to its structure, we can conclude that any saw is suitable. Yes, indeed, this is so, but it can be chopped off with an ax, but not everything that can be done will be useful and correct.
• The clearness of the cut will depend on what the laminate is drunk (the edge of the panel can have a torn cut). Therefore, the smaller the cutting structure of the disk or saw, the smoother the fishing line for the trimmer of the saw.
• But the evenness of the cut depends not only on small teeth, but also on the speed with which the canvas cuts the panel, as well as on the quality of the metal from which the cutting element is made. So a file for an electric laminate can have large teeth, but leave an excellent slice.
• I would like to pay attention to the fact that the file for the jigsaw on the laminate, as such, does not exist at all, but there are just wood or metal files or metal. For cutting laminated panels, any of them is suitable, but the small canvas for the metal is more in the structure of the laminate, and the large (on wood) moves much easier, although the cut is almost the same.
• It is very good to cut the laminated panels of an electric circular, where the saw disks in laminate are the most ordinary wood drives. Here, again, you can pay attention to the fact that there are no discs specialized for cutting the laminate and such can be called almost any canvas of manual electrocircular.
• The inconvenience of this method of cutting is that with it it is extremely difficult to cut in different directions, because the saw disk according to the laminate cannot be expanded to direct the cut along another line. An electric jigsaw copes with such an operation excellently and if any figured neckline is needed, then a metal saw is very well suitable for this, like a thinner.

Advice. If you cut the laminate with a hand.made electrocircular, then keep in mind that the disk on it rotates from the bottom up, therefore, if it is not very sharp, then the paper on the panel will have a torn edge. So that this does not happen, when cutting, turn the board with the front side down.

• Laminate can also cut a corner grinder, although this method will cause strong smoke, but sawing disks according to the laminate in this case will be disks for metal or concrete. The high speed of rotation of the angular grinding machine allows you to easily cut not only the laminate, but also the tree. But you can also insert a canvas with teeth into a corner grinder, although this is not the best option, because the cut is not very smooth.
• The simplest cutting tool for laminate can be a hacksaw for metal or wood, but with small teeth. In this case, the canvas for the metal will leave a more clear cut, but it is difficult to cut wide panels or cut them along the length.

Advice. If you need to cut off a piece of laminate along the length, but there are no suitable cutting tools at hand, then you can do with an ordinary construction knife. Under the ruler, draw a deep fishing line for a trimmer in the upper layer, and then break it with a blow of the hand, pressing the other part to the panel with a knee to a table or stool.

Using a hacksaw for a cut of laminate

Ножовка

The hacksaw clearly does not lead in the ranking than to saw the laminate, but sometimes a person has only it at hand. The classic hacksaw has very large teeth, and with their help it will not be possible to cut the board quite beautifully.

For a high.quality saw, a hacksaw with small teeth is needed.

По дереву

Explicit drawbacks include the duration of the process. The use of a hacksaw can be justified if it is necessary to file a small angle or make a cut across the board. The use of a hacksaw for a cut of a laminated board along the entire length is a catastrophic loss of time.

About the laminate

The processing of any material requires any special tools suitable for this composition. You won’t cut ceramic tiles with a hacksaw, and cut metal with glass cutter, because even the best cutter for one structure will be completely useless for the other.

That is why we will figure out what the laminate consists of, and also see the photo and video about laminated panels.

What is Laminite made of

Four main layers of the laminated panel

• The lowest layer, which is marked in the figure, consists of unrefined or made paper. It is a reliable obstacle for moisture, which can come from the main sex. Sometimes an additional substrate under the laminate for sound and thermal insulation is added to the paper, but this happens only in individual collections and the price of the material changes significantly from this.
• The thicker layer of the laminated panel is indicated by the number 2, it is made of high.fiber stove of high density (HDF) and the quality of the products largely depends on its thickness. The castle is cut into this layer and the thicker the wood.fiber slab, the higher the locking of the lock, therefore, the groove is deeper and the connection is denser (lack of clearance).
• The number 3 in the figure indicates a decorative layer of paper, on which a certain drawing is applied. Since the drawing can display many materials, the panels can imitate various wood of wood, wooden and ceramic parquet, stone, sand, marble and the like.
• The highest, fourth layer, consists of acrylic or melamine resin. Through it almost without interference, the decorative design of the panel is clearly visible. The class of abrasion, wear resistance of the laminate depends on the thickness of the protective upper layer, and, therefore, its belonging to a commercial or household category (classification of domestic (non.profit) laminate begins with numbers 2, and commercial. with numbers 3).

Coming of laminated panels

Makita. the best files for an electrician laminate

• If there is an instruction on what is better to cut a laminate, then it probably looks more like advice, not instruction. After all, if you pay attention to its structure, we can conclude that any saw is suitable. Yes, indeed, this is so, but it can be chopped off with an ax, but not everything that can be done will be useful and correct.
• The clearness of the cut will depend on what the laminate is drunk (the edge of the panel can have a torn cut). Therefore, the smaller the cutting structure of the disk or saw, the smoother the fishing line for the trimmer of the saw.
• But the evenness of the cut depends not only on small teeth, but also on the speed with which the canvas cuts the panel, as well as on the quality of the metal from which the cutting element is made. So a file for an electric laminate can have large teeth, but leave an excellent slice.
• I would like to pay attention to the fact that the file for the jigsaw on the laminate, as such, does not exist at all, but there are just wood or metal files or metal. For cutting laminated panels, any of them is suitable, but the small canvas for the metal is more in the structure of the laminate, and the large (on wood) moves much easier, although the cut is almost the same.
• It is very good to cut the laminated panels of an electric circular, where the saw disks in laminate are the most ordinary wood drives. Here, again, you can pay attention to the fact that there are no discs specialized for cutting the laminate and such can be called almost any canvas of manual electrocircular.
• The inconvenience of this method of cutting is that with it it is extremely difficult to cut in different directions, because the saw disk according to the laminate cannot be expanded to direct the cut along another line. An electric jigsaw copes with such an operation excellently and if any figured neckline is needed, then a metal saw is very well suitable for this, like a thinner.

Advice. If you cut the laminate with a hand.made electrocircular, then keep in mind that the disk on it rotates from the bottom up, therefore, if it is not very sharp, then the paper on the panel will have a torn edge. So that this does not happen, when cutting, turn the board with the front side down.

• Laminate can also cut a corner grinder, although this method will cause strong smoke, but sawing disks according to the laminate in this case will be disks for metal or concrete. The high speed of rotation of the angular grinding machine allows you to easily cut not only the laminate, but also the tree. But you can also insert a canvas with teeth into a corner grinder, although this is not the best option, because the cut is not very smooth.

Laminate can be cut with a hacksaw on metal

• The simplest cutting tool for laminate can be a hacksaw for metal or wood, but with small teeth. In this case, the canvas for the metal will leave a more clear cut, but it is difficult to cut wide panels or cut them along the length.

Advice. If you need to cut off a piece of laminate along the length, but there are no suitable cutting tools at hand, then you can do with an ordinary construction knife. Under the ruler, draw a deep fishing line for a trimmer in the upper layer, and then break it with a blow of the hand, pressing the other part to the panel with a knee to a table or stool.

How to cut a laminate at home recommend a pro

The Stroyvelikan website conducted a survey of professional masters who had to lay laminate on the floor dozens of times. Experts voted for the best tool for working at home, resulting in an unpretentious rating with opinions and useful recommendations.

Location: Electricity with three types of saws

Yuri, 38 years old. It seems to me that it is better to cut a laminate with an electrician. The panels themselves are narrow, usually have a thickness of not more than 12 mm, require the most accurate saw. It is convenient to work with the tool due to a small sole with transverse, longitudinal and curved cutting. It is comfortable to make side cutouts for pipes, protruding parts of the wall.

I recommend cutting a laminate with three types of files:

• T101B. When working on the opening of the panels, a pure cut is noted. The teeth of the canvas are directed up, so the workpiece vibrates less on the desktop. The saw is cheap, quickly stupid.
• T101AO. suitable for curved cutting. A small tooth saws a laminate without chips, but the speed is low. In large volumes, cutting the material is problematic.
• T101BIF. The bimetallic canvas leaves clean cut on both sides. Polished teeth are located without focusing up or down. The file is characterized by an increased service life.

Advice! When using an electrician, I recommend cutting the panels from the reverse side so as not to damage the front layer on the edge. Lead the tool clearly along the line, try to make a full pass without stopping.

Place: A cut with a curved blade

Evgeny, 32 years old. For more than 2 years I have been using a laminate with a curved blade when laying a laminate. The most reliable and simple device. When working, there is no excessive noise and a large amount of dust, as in the case of power tools. The wires do not interfere, since the connection to the mains is not required.

It is very convenient to cut the laminate across, make longitudinal and diagonal cutting more difficult, but you can still. To do this, put the panel in front of the cutter strictly according to the marking. I cut about two.thirds of the blades, move the workpiece forward and continue to the edge.

Place: Corner grinder with a diamond disk

Nikolay, 45 years old. I propose at home to saw a laminate with a corner grinder. However, this tool requires careful treatment. There is no support sole, so the quality of the cut will depend on the ability to hold an angle grinding machine in the hands. With uncertain handling, it is easy to damage the panel.

For cutting laminate, I recommend using diamond discs:

The panels can be cut without chips directly from the front side. With proper work with the tool, an even edge is formed. However, the cut of the material is accompanied by a lot of dust, so it is better to cut on the street or in a well.ventilated room.

Place: circular saw with a disk for neat cut

Sergey, 35 years old. Not the easiest tool for a beginner, but quite suitable for cutting laminated panels. The saw disc is much more reliable than the electric canvas. Does not break and does not bend at the same loads. Work is faster, vibration is missing.

Personally, I had to cut a laminate with a circular saw with a 190×30 mm disk, which has 56 carbide teeth and is intended for neat cutting of materials with a laminated surface. The cut of the cut was installed in accordance with the thickness of the panels, while the edges of the teeth should be 1-2 mm exceeding this indicator.

Practice has shown that it is better to cut from the side of the decorative protective layer so that the edges are even, without chips. The sole of the disc saw is wider, vibrations do not occur during sawing, so the upper part is not damaged.

Location: a knife.haired woman with a small tooth

Dmitry, 28 years old. If there is no power tool at hand, and the laying area is relatively small, while there is nowhere to hurry, then I recommend taking a regular hacksaw on the tree. With this simple and affordable tool, even a novice master will be able to cut evenly a laminate. We will have to work, but the longitudinal, not transverse cuts are of particular difficulty.

I liked working with a hacksaw with a canvas 11-12 teeth per inch. Trihedral sharpening accelerates the process and makes cutter. Sawed the panels on the front side, there was no chips left with neat handling. With increasing teeth, the risk of damage to the protective and decorative layer will increase.

How to saw a laminate are tried by users

Andrey, 22 years old. I live in a one.room apartment, I decided to put a laminate in a room on an old parquet. I have not yet acquired the instrument. I took a hacksaw “Piranha” in the store with a hacksaw with teeth step 15 per inch. High.quality sharpening, even after laying continues to cut well, does not leave chips. He saws along and down without problems, the blade does not clamp, but manually adjust the last panels in width still energy.intensive.

Pavel, 44 years old. On his old electrician installed a T101BIF file to cut a laminate without chips. The bimetallic canvas copes well with sawing the panels along and across. Laid a laminated coating in a private house on the ground floor 10 mm thick (33 class). The entire area, not counting the bathroom, was about 60 square meters. m. The saw did not break, even at the very end I sawed perfectly. Only positive emotions remained.

Peter, 48 years old. I liked to use a special laminate cutter. A guillotine with a curved blade cuts panels with a minimum noise, which in the apartment is very important. During work, a lot of fine dust is not formed, only large waste remains, which are easy to collect. The machine is suitable for straight cuts in width, length and at an angle. There are no large chips when cutting. Due to a large lever, you do not have to make a lot of effort.

Alexander, 52 years old. I tried at home to cut a laminate with a corner grinder with a diamond segmented disk on concrete. It saws quickly, it turns out an even edge, you don’t get tired when working. The only thing that is very dusty is very small particles that fly throughout the room. I cut it on the street, since I live in a private house, it is not a problem to go out.

Oleg, 29 years old. Of the power tools, only a circular saw was at home. I used a wooden wood disk with carbide attacks “Zubr” for cutting. Chose with 48 teeth. Prepared a convenient table from black boards. Laid a laminate with a thickness of 8 mm, set the depth of cut to this size, taking into account a small output of 1-2 mm. There is no much experience with power tools, so he cut along and across the guide to make the edges even.

General information

If you choose a wood.based flooring, then people often give their preference to natural parquet or a cheaper, but no less visually pleasant option. laminate. Such material is characterized by increased resistance and features that will even exceed natural solutions for operation.

In construction stores you can find different laminate design. World.class companies can offer end users a wide variety of textures that will simulate natural surfaces, for example, trees of various types.

Such a coating has become popular largely due to the fact that it is very easy to lay a laminate using a castle system. Also, such coatings are quite easy to dismantle and install again.

Laminate is quite easy to lay and, if necessary, cut, armed with special tools

The coating is laid in rooms where increased patency is observed. This is largely due to the fact that the laminate has increased indicators of wear resistance, and the loads are not terrible. If you lay in a bedroom or living room, then the tones of wood of warm shades will create a cozy atmosphere, and thanks to resistance to water, you can not be afraid that fungus or bacteria will develop in the kitchen.

How and how to cut a laminate at home

What is the cutting of the laminate the simplest? It should be neat, correct, thought out. The cut can be carried out using a jigsaw, especially if it is an electric tool.

For cutting laminate, many experts recommend using an electrician

It is by means of an electrician that you can make a cut:

An alternative can be the most ordinary manual saw or hacksaw, but this process will take much more time. Due to the fact that the cost of such a product as an electrician is not too small, and laying the laminate is carried out quite rarely due to a long service life, it is not advisable to purchase for personal use.

The method of cutting tiles is precisely a kind of electricity, and requires compliance with safety and operation rules. The laminate is cut into small cloves. Such a canvas is in the set of each electrician and, if necessary, you can buy an additional.

The cut is carried out according to the previously made marking. The marking should be on the back of the laminate. Next, cutting is carried out, but with a carefully fixed board, for which you can use a heavy object or at all, your own hand. It is advisable to conduct a section with additional help.