How to get a mower of a gasoline Huter. Huter GGT-1500S is a power trimmer occupies…

How to start a trimmer for Huter grass correctly

Before adjustment, it is necessary to carefully clean the filters according to the maintenance in the instructions.

Further configuration of the carburetor of the lawn mower with your own hands is performed by adjusting screws. There are three of them:

Right (l). adjustment of the fuel mixture for low revolutions.

You need to find the maximum speed at idle. To do this, they slowly turn the screw (l) to the right and left.

For adjustment, the screw is rotated by a quarter of turning must be counterclockwise.

Lower (t). is responsible for adjusting the engine at idle.

For proper adjustment of the idle, it is characteristic:

• Sustainable operation of a cold engine;
• non.high speed of the hot engine;
• for a trimmer head, a large supply supply;
• Sustainable engine operation when changing positions (sharp rise or descent of a knife).

Left (H). adjusting the mixture at high speeds. (The screw is set up last).

The overall adjustment of the maximum revolutions, engine power, temperature and gas consumption depends on the left screw (H).

Setting a carburetor of a lawn mower with a last screw is performed as follows:

• Open the throttle to the full, while issuing a full gas. Turn the screw clock until the speeds fall (in this case, they are oriented by ear).
• Turn the screw as slowly against the clock until the non.uneven operation of the engine.
• Then turn back very little, barely hearing a stable, even work.
• For more visual use of skills, it is more convenient to consider the work of an experienced user:

It is interesting that from the point of view of the author of the video, the configuration (its correctness) is determined by the color of the candle, and not just by the speed and stability of the engine.

Correct tuning of the carburetor with your own hands in this case-combustion of the fuel mixture without a residue, the color of the candle should be light brown.

The trimmer for the grass is not started due to the malfunction of the carburetor

One of the most difficult reasons for the impossibility of launching a lawn mower is a carburetor. This mechanism is responsible for the preparation and good supply of the fuel-air mixture to the cylinder. If the carburetor is clogged or adjusted incorrectly, then the lawn mower may not start or work unstable. Detailed instructions on how to adjust the carburetor on a benzocosa is described in this material.

If the adjustment does not help restore the stable operation of the tool engine, or the trimmer for the grass does not start at all, then the carburetor should be removed and repair it. The entire repair of the carburetor is that you need to disassemble it, clean all channels and constituent elements. If necessary, replace the failed details. membranes, filters, etc.P.

If the suspicions fell on the carburetor, then you should pay attention to the following types of malfunctions:

• Canals and nozzles clogged. special liquids can be used for cleaning, however, it is best to disassemble the mechanism with its thorough flushing. The reason for the clogging of the channels and jackets of the carburetor is the storage of a tool with fuel in the tank
• Wear of the carburetor gaskets. rubber seals contribute to the fact that the tightness of the mechanism is disturbed, as a result of which the serviceability of the functioning is violated
• Memory of carburetor membranes. they are responsible for downloading fuel to the device

To make sure the CPG malfunction, you should check the compression, which is described above.

Specifications

Before making a choice in the direction of a particular model of equipment, you must familiarize yourself with its technical characteristics. The Huter GGT 2500S model is no exception, the operating instructions of which are presented below. This unit is a device whose power reaches 3.3 liters. With., or 2.5 kW.

As a cutting tool, a knife or fishing line for a trimmer is used (by choice). The design has a bicycle handle and a hard drive shaft. Speasing width is 25.5 cm. When consumers consider this Huter lawn mower, they pay special attention to the spindle rotation frequency. In this case, it is 9500 per minute. The landing diameter is 25.4 mm. You may also be interested in the level of noise, which is 96 dB. Weighs the unit 7 kg. The thickness of the used fishing line is 2.4 mm.

How to refuel a trimmer for grass

The finished mixture of gasoline with butter can be stored for no more than 3 months (clean gasoline is stored less). Dilute the fuel in the quantity that is enough for several applications of the trimmer for the grass. In general, prepare:

• gasoline and oil, which is suitable for two.stroke engines with an air cooling system;
• metal canister and a mixture container;
• respirator;
• gloves.
• Pour 1 l of gasoline into a suitable volume of 1 l of gasoline and add 1/2 of the desired amount of oil.
• Mix carefully, being at a decent distance from the sources of open fire.
• Add the rest of the oil to combustible and mix everything again.

General recommendations for refueling a trimmer for grass with a two-or four-stroke engine:

• Place the fuel tank so that the cover is located on top, and then pour the required amount of fuel.
• Do not overfill the fuel tank. This will lead to one of the problems: transferring into the intake pipe and fuel filter, flammable ignition or breakdown of the motor.
• Try to fill the mixture so that it does not spill. To do this, you can use the watering can.
• If you still poured fuel, then immediately wipe it. Put the wiping material, do not accumulate indoors. this is fire hazardous.
• The launch of the device should begin after the canister with fuel is removed at a distance of more than 10 m.
• If there was a long break between the operations of the mowing, then the remaining old fuel be sure to drain.

How to refuel a trimmer for grass

The finished mixture of gasoline with butter can be stored for no more than 3 months (clean gasoline is stored less). Dilute the fuel in the quantity that is enough for several applications of the trimmer for the grass. In general, prepare:

• gasoline and oil, which is suitable for two.stroke engines with an air cooling system;
• metal canister and a mixture container;
• respirator;
• gloves.
• Pour 1 l of gasoline into a suitable volume of 1 l of gasoline and add 1/2 of the desired amount of oil.
• Mix carefully, being at a decent distance from the sources of open fire.
• Add the rest of the oil to combustible and mix everything again.

General recommendations for refueling a trimmer for grass with a two-or four-stroke engine:

• Place the fuel tank so that the cover is located on top, and then pour the required amount of fuel.
• Do not overfill the fuel tank. This will lead to one of the problems: transferring into the intake pipe and fuel filter, flammable ignition or breakdown of the motor.
• Try to fill the mixture so that it does not spill. To do this, you can use the watering can.
• If you still poured fuel, then immediately wipe it. Put the wiping material, do not accumulate indoors. this is fire hazardous.
• The launch of the device should begin after the canister with fuel is removed at a distance of more than 10 m.
• If there was a long break between the operations of the mowing, then the remaining old fuel be sure to drain.

We proceed to running the lawn mower

After starting, do not rush to immediately run the trimmer for the grass. Let the engine idle for 5 minutes. While heating is going on, adjust the air supply to the air damper with a lever so that the rogue with a fishing line or with a knife does not rotate. As soon as the tool warmed up, we completely open the air supply to the corresponding lever to the “ON” position and squeeze the gas trigger for 1/2 and hold the seconds of seconds 30. Then we drop the gas, let the trimmer work on xx 30.40 seconds. In this mode we continue 10 minutes 15. Then we mock and let it rest for 15 20 minutes.

Having cooled the lawn mower, we continue to run the engine according to the previous scheme. Start a hot, a trimmer for grass should already be with an open air damper. Try not to hold the gas for a long time, since the movable details of the tool only rubbing each other. And do not let the engine work at idle for a long time as it can overheat.

The next stage is the run.in a gas reducer gearbox for grass. To do this, select a plot with soft young grass. Kosim 5 10 minutes with 1/2 2/3 from full gas. After we take a break for 20 25 minutes. Repeat the cycle 3 4 times.

In general, therapist for the lawn mowing according to the described algorithm is carried out until the fuel mixture in the tank is fully generated. After which the tool is ready for long.term work. In the process, follow the temperature regime of the gearbox and the motor. They should not overheat.

Instructions for Huter GGT-1500T

one. Introduction ………………………………………………………………………… 3 2. Safety regulations……………………………………………………. 3 3. Technical characteristics …………………………………………………… 4 4. Assembly………………………………………………………………………………… 5 5. Operating instructions ………………………………………………………………………………….………… 8 6. Running

Do not remove the lid of the fuel tank when the engine is running. If the fuel spills when filling the tank, be sure to wipe the fuel spots with a dry cloth and change the place before starting the engine. ten. Do not use the fuel mixture to clean the trimmer for grass. eleven. Any maintenance and replacement measures

Assembly of a trimmer for grass 1 2 2 3 4 5 6 7 8 9 10 11 12 handle Starter Starter Starter control lever cap of a high.voltage wire lid Fuel tank lid Leville handle Handbone Corps Fuel tank right handle control hilt of the handle mount

one.Barbell.(for the GGT-1500S model) squeeze the fixing lever of the mounting system, and combine both parts of the bar. Fastening the fixing lever should enter the guide groove on the lower rod. The correctly assembled connection cannot be opened without pressing the fixing lever. Tighten the additional

Install a cutting knife on the hub. Make sure that the cutting knife is correctly specified and lies on the hub groove. Install the mounting cup on the shaft. Install (bait) a nut on the shaft. Check the correct installation of a knife. Holding the stopped rod with one hand, tightly tighten the nut

On the control handle, set the ignition to the “inclusive” position. 5. On the control handle, press the gas trigger and fix it. 6. Hold the trimmer for the grass with one hand, pull the starter handle with your free hand until it is “engaged”. Pull sharply, until the first start of the engine (Fig.). Rice.9 Fig.ten

Stop a trimmer for grass 1. Release the throttle control lever. The engine should cool slightly, working at idle. 2. Transfer the ignition switch in the direction of the arrow indicated on the control handle to the Stop position. WARNING. After the production of the fuel mixture from

Maintenance 1. Air filter is cleaned or replaced by a foam element of an air filter every 10 hours of operation. The condition of the air filter is one of the main conditions of the reliable operation of the engine. Remove the air filter casing (rice.fifteen). Pull out

Old or incorrectly cooked fuel mixture. air filter. Drain the fuel mixture from the fuel tank. Pour a clean, fresh fuel mixture. Storage store a trimmer for grass is necessary in a pure form in a dry room, inaccessible to outsiders, children and animals. Before long.term storage

Unified Technical Support Service E-Mail: Servis@Huter.Su Web Site: http: // www.Huter.SU Address of your service center:

Certificate of acceptance of the gasoline trimmer for grass “Huter” of the GGT series of the GGT _ No. _ recognized as a suitable for operation, the date of sale _ I am a buyer/representative of the company with the terms

Dear buyer! We express you great appreciation for your choice. We have done our best so that this product satisfies your needs, and the quality corresponds to the best world samples. The manufacturer company sets the official service life for gasoline trimmers for grass for 5 years, at

Preparation of the fuel mixture and refueling

For the convenience of making fuel mixture, it is better to have a special canister. where one part contains gasoline, and in the other 2 stroke oil. We recommend getting similar, it is very convenient to use https: // ru-sad.RU/Prinadlezhnosti-Dlya-Sadovoy-Tehniki/Dlya-Benzopil/Kanistryi/

Next, take a measured container, with a scale applied to it, with its help you can prepare the mixture as accurately and quickly as possible. See in the instructions which brand of gasoline and 2-stroke oil https: // ru-sad.RU/Prinadlezhnosti-Dlya-Sadovoy-Tehniki/Masla-I-Smazki/recommended by the manufacturer of your lawn mower model. Pour gasoline and oil into a container for the preparation of the fuel mixture, according to the proportions specified in the instructions. Then the finished mixture neatly, through the funnel, pour the trimmer for the grass into the fuel tank. The ratio of gasoline and oil should be just the same as indicated in the instructions. This is a very important point!

Launching a lawn mower with an unfinished engine

For the first launch of the lawn mower, find the air damper lever and put it in position “Closed”. Turn on the ignition on the handle. If your model has a manual fuel pump, the people are called a suction, then click on it 3-5 times until you see the fuel mixture inside the primer. Now the tool is ready to launch. Put a trimmer for grass on a flat surface to ensure a stable position. Smoothly stretch the trigger cable until you feel its resistance, and then pull the cord with a sharp movement 3-5 times.

If the engine started after 5 jerks, then open the air damper. If this does not happen, still open the air damper (with an open damper and continuation of attempts to start the engine, the fuel flows a candle and you will have to dry it, and this is extra waste).

If the engine does not start, with an open damper, then close it to continue to pull the cord. The first launch may be quite difficult and demand up to 15 jerks. After the engine has begun to work, click once on the gas lever, so you will use idle. Now let the engine work and warm up. After that, it can be stopped by pressing the “Stop” button.

Why the chainsaw is not started?

If you did everything according to the instructions, but the chainsaw does not start, then something is wrong. This may be due to some common reasons: lack of sparks; fuel is not supplied; The air filter is clogged. So, below we offer a procedure that will help determine the reason why the chainsaw does not start.

Read does not start a lawn mower does not receive gasoline

Procedure if your chainsaw does not start

The first thing to note if you do not launch a chainsaw. Do not tighten the screws on the carburetor. If you are not an expert, you still will not be able to adjust something yourself, and you will not be able to run the chainsaw.

Follow the following actions to run the chainsaw in the indicated order, starting from the next number, only if the previous one did not help.

First, try to leave the chainsaw at rest for 5-10 minutes. It is possible that the candle was filled during winding. It happens. Then try to start again in accordance with the instructions. Remove the lid from the chainsaw, remove the air filter and try to run without it. If the filter is contaminated, it should be washed in soapy water and dried or replaced with a new. Twist the light of the fuel from the chainsaw. Check for sparks. If there are no sparks, try to put a new candle. If the spark does not appear, this means that the ignition unit is damaged and the saw must be transported for repair. However, visual observation of a spark does not mean that the ignition unit is in good condition. If a spark occurs, but the chainsaw is still not working, follow the following actions in the list. If there is a spark, but the spark plug is wet, turn the chainsaw to drain excess gas from the cylinder if it accumulated there. Pull the starter of the spark plug 10-15 times to ventilate the combustion chamber. Light a candle and tighten it back, but it is better to replace it with a new one if it is. Try to start again according to the instructions. If the candle is dry, place one or two cubes of the gas mixture in the syringe and fill it in the cylinder. Try starting the chainsaw. There may be a small spot in the carburetor, which prevents fuel from entering the combustion chamber

It is possible that this will be displayed by the stream generated after the launch of the chainsaw, adding fuel directly to the cylinder. Unscrew the muffler and remove it, observing caution so as not to damage the gasket between the silencer and the engine. Try to run without a silencer and air filter

Having removed the muffler, you can inspect the piston inside the chainsaw. If there are burrs or nests on the walls of the cylinder or piston, or the ring on the piston is hidden by burrs, you will have to be very upset, because this means that the piston is damaged or worn out. This usually happens when the oil is added to the fuel mixture. In this case, you will have to contact the service and, possibly, think about buying a new chainsaw, since replacing the piston. Pretty expensive operation.

Thus, in this article we discussed how to launch a chainsaw “according to the instructions”, and also what to do if the chainsaw does not start. We hope that you will find these advice useful.

Rules for the operation and storage of gasoline baskets

In order for the bureau to work well in the future, it is necessary to provide it with good storage and operation conditions:

• During operation, carefully monitor the cooling system, carefully and timely clean the channels in the case, as well as the starter’s ribs;
• If necessary, use solvents, kerosene and other detergents for cleaning;
• Do not clean the tool “hot”. Let him cool;
• Strictly follow the operating instructions, otherwise you can overheat the engine;
• If you do not plan to use a bureau next month, the fuel mixture should be drained from it, because over time it breaks up into heavy fractions that clearly clog the carburetor channels;
• After draining the fuel, release the trimmer for the grass at idle until it dies, this will help to completely remove the remains of the working mixture.

Before winter storage, follow the following actions:

• Completely disassemble adhesive tape, wash and clean all the details that may be;
• Inspect the details for damage, if necessary, eliminate distortions, impulses, bends and any other malfunctions;
• Pour enough oil into the gearbox and clean the air filter;
• You can partially disassemble the engine, rinse, blow and grease all the moving parts;
• To lubricate the piston, unscrew the spark plug, raise the piston to the dead point using the starter, pour a little oil into the spark plug and turn the crankshaft several times;
• If you do not hold the bureau in your house, wrap the engine with an oiled rag.

How to start a trimmer for Huter grass correctly

How to start a trimmer motor for grass or lawn mower?

The new trimmer for the grass is simple in commissioning.

• Check the type of device motor. Trammers for grass are equipped with a 2- or 4-stroke engine.
• Buy oil for this type of motor. Gasoline for a trimmer for grass-AI-92/93/98, is sold at all gas stations.
• Mix oil with gasoline. Mineral oil is mixed in a ratio of 1: 34 with gasoline, synthetics. in 1: 50. Follow the tips of the trimmer manufacturer for the grass for the viscosity of the oil (see. label on the flask). often use all-season oil 5W-30. Do not use unverified car.
• Pour a small amount (for example, 0.5 liters) of the resulting fuel in the tank.
• Close the air conditioning by shifting the suitable lever (see. annotation).
• Turn the ignition key (or handle) to the “inclusive” position. without this, the trimmer will not start for the grass. Newcomers often make such a mistake.
• Skip a little fuel in a carburetor. if there is a manual “rocking” with a separate button or lever (see. annotation). We need 4-7 presses.
• Install Trimmer for grass On a flat surface.
• Carefully pull the starting cord until you feel its brake. Then abruptly pull it out, but not quite. Repeat this movement before 4 times.
• If the engine does not start, open the air damper again, it will flood the candles with a different gasoline during subsequent movements of the cord. Make 2-3 samples to start an open handbrake motor.
• If the motor does not start, close the damper and make a few more attempts to it Bind.
• After starting the engine, click on the gas lever, turning on the idle.

How to start a gasoline Trimmer for grass?

How to start correctly Trimmer for grass. the question that the owners are puzzled in the event of a breakdown of the device. And after the successful repair of the trimmer for the grass, the owner tries to avoid repetition of the same situation.

Starting the lawn mower for the first time or after a long downtime

The lawn mower differs from a trimmer for the grass in that a fishing line for a trimmer, but a mechanical gearbox or winch based on the gear equipped with a knife, acts as a cutter for grass. The knife drive is much more powerful than the forest mechanism. a powerful lawn mower is also used when cutting the bushes. Both Chinese and European law mmores do not differ in anything special when the declared capacity is real.

For lubrication of gear gears, Litol or solidol is used. Having checked the gearbox, prepare for the work and the engine itself. according to the above instructions. If the start has failed, the problem is already in the engine.

Prerequisites

The reason for which the trimmer for grass fails may:

• tank overflow;
• excessive fuel pumping into engines equipped with manual supercharger;
• wear in the motor of valves, cylinders, nozzles, fist pushers and other mobile parts;
• In the tanks, gasoline and/or oil ended;
• not in order of the spark plug;
• clogging of fuel or air filters;
• the valves in the motor were resolved or burned.

Fuel pouring through the openings for candles

If there is no manual pumping on the engine of the trimmer for the grass and the device did not start, pour a little fuel into the motor itself through candle moves. Make the following.

• Check if the fuel level is sufficient in the tank for draining a small amount of it. It takes only 20 ml.
• Remove the cap from the candle and unscrew it with a candle key.
• If the candle is polluted on the former use of the trimmer, rinse and buy it. There should not be any deposits on the electrodes of the candle. Do not damage the ceramic insulator of the central conductor. In the new trimmer, check the candles for the factory defect.
• Return the candle back and check the spark look (category between electrodes) when the starter triggers.
• Remove the candle again. Using a 20- or 50-cup syringe, pour 20 ml of gasoline into a candle hole from under a candle.
• Insert and fix the candle by setting the magnitude of its technological clearance at least and no more than a millimeter.
• Skip fuel using a button (or lever) of swinging. if it is on your model of a trimmer for grass. Press the button every 4 seconds.

Now try to start the motor. Close the air conditioning immediately after starting.

The main thing. Fuel mixture!

In this case, the remains of plastic plastic dissolved in the brutal environment are created in the combustion chamber so terrible things that you will definitely not be able. But you certainly remember how to store fuel forever.

What to do when the fuel was definitely normal, there is a spark, but a trimmer for grass does not start a gasoline? It is possible that you just flooded the candle with gasoline. In this case, it must be turned out, wiped with a clean rag and dry. By the way, it will be completely useful to check the candle for performance itself.

The carburetor of the lawn mower floods.

How can you drown the engine on a gas tank, to be inattentive. Just one awkward movement

After several jerks, he will start and stall, which is a normal phenomenon. Putting the damper to the working position, start the tool again and start working.

Why not start Trimmer for grass. the reasons

To determine why gasoline Trimmer for grass It is poorly started or constantly stalls, it is necessary to sequentially check the work of all the main components of the unit. It is especially important to do this after a long.term storage of a lawn mower. So, the main reasons for such a trimmer’s behavior for the grass are as follows:

• The culprit that the lawn mower is not started, there may be a poor-quality oil-Benzine fuel mixture. It must be prepared strictly according to the instructions. The savings here are not at all appropriate, since it can lead to the failure of the entire piston group of a trimmer for grass. Do not cook too much fuel mixture, as excess gasoline will lose their qualities over time.
• You should know that gasoline trimmers for grass of stamps such as STIHL, Husgvarna and some others do not start if they are filled with cheap gasoline with a small octane number. Therefore, for such units, it is necessary to use only high.quality high.octane fuel.

How to start a trimmer for grass gasoline Huter

How to launch a trimmer for grass. This is a question that the owners confuse in the case of failure of the device. And after the successful repair of the trimmer for the grass, the owner tries to avoid repeating the same situation.

The reason for the failure of a trimmer for grass is possible:

• Tank overflow;
• Excessive fuel injection into engines with manual supercharger;
• Wear in the engine of valves, cylinders, injectors, fist pushers and other moving parts;
• Gasoline and / or oil end in tanks;
• The spark plugs failed;
• Fuel or air filters are clogged;
• Incorrectly spelled out or burned valves in the engine.

The test begins with the presence of oil and fuel in both tanks and a small part in the engine system. The “empty” engine will not start, despite the full tank, and also overflow.

How to start a three.dimensional motor or bush?

The new trimmer for the grass is simple during commissioning.

• Check the type of engine engine. Trammers for grass are equipped with a 2- or 4-stroke engine.
• Buy oil for this type of engine. Gasoline for a trimmer for grass. AI-92/93/98, sold at all gas stations.
• Mix oil with gasoline. Mineral oil is mixed in a ratio of 1:34 with gasoline, synthetic. At 1:50. Follow the recommendations of a trimmer manufacturer for grass regarding oil viscosity (see. Label on the flask). The most commonly used polyhedral oil. 5W-30. Do not use unverified motor oils.
• Pour a small amount (for example, 0.5 liters) fuel into the tank.
• Close the air damper, moving the desired lever (see. Instructions).
• Turn the ignition key (or handle) to the “inclusive” position. Without this, the trimmer for the grass will not start. Beginners often make this mistake.
• Download a little fuel to the carburetor. If there is a manual “rocking” with a separate button or lever (see. Instructions). 4-7 clicks are required.
• Place a trimmer for grass on a flat surface.
• Gently pull the starter cord until you feel its braking. Then pull it sharply, but not completely. Repeat this movement up to 4 times.
• If the engine does not start, open the air damper again, otherwise the spark plugs are filled with gasoline during subsequent movements of the cord. Make 2-3 attempts to start the engine with an open manual brake.
• If the engine still does not start, close the shutter and make a few more attempts to run it.
• After starting the engine, press the throttle lever to activate idle.

Let the engine warm up. 5-10 minutes enough. Do not start mating grass immediately after a cold launch. The engine of the trimmer for the grass should start.

Starting the brush for the first time or after prolonged downtime

The lawn mower differs from the trimmer for the grass in that the lawn mower. This is not a fishing line for a trimmer, but a mechanical gearbox or a winch with a gear, equipped with a knife. The knife drive is much more powerful than the carriage mechanism. When cutting bushes, a powerful bush is also used. Both Chinese and European law mowers do not differ when the declared capacity is real.

Litol or solid oil is used to lubricate gears gearboxes. After checking the gearbox, prepare for the engine itself. In accordance with the above instructions. If when starting, a failure occurs, the problem is already in the engine.

Share fuel through the spark plugs

If there is no manual pumping on the engine of the trimmer for the grass, and the device does not start, pour a little fuel into the engine through the spark plugs. Make the following.

• Make sure that the fuel level in the tank is sufficient to drain a small amount. It will take only 20 ml.
• Remove the lid from the spark plug and unscrew it using the spark plug for a candle.
• If the candle is contaminated with the used trimmer, rinse and bake it. There should be no deposits on electrode electrodes. Do not damage the ceramic insulator of the central conductor. In the new trimmer, check the spark plugs for factory defects.
• Turn the spark plug back and check the ignition (discharge between the electrodes) when the starter lights up.
• Remove the candle again. Using a syringe with a volume of 20 or 50 cm3, pour 20 ml of gasoline into a hole for the spark plug.
• Insert and secure the spark plug, setting the value of its technological clearance at least and no more than a millimeter.
• Pour the fuel with the shift button (or lever). If this is in your model of a trimmer for grass. Press the button every 4 seconds.

Now try to start the engine. Close the air damper immediately after starting.

Checking the ignition system

If the trimmer for the grass has already been used, check the condition of the removed (currently) spark plugs, replacing it with any other. If, for example, when checking the spark plug, the ceramic dielectric broke, the electrodes bent, buy one, guided by the product code knocked out for the parts itself, and check it with a marker in the instructions at the trimmer. A spark plug without a insulator and / or with curved electrodes will not give normal sparks when triggered.

If the spark plugs are in order, but the fuel sparking is not observed, check the ignition coil with an ohmmeter (multimeter). Lack of indications (infinite resistance) is a sign of winding winding. If it sins from overheating due to a short circuit, the voltage for the spark malfunction will be insufficient.

Since he uses a very thin wire that converts 12.6 V from the battery of 30,000, it is very difficult to fix (rewind) even in the garage. The coil should be replaced.

How to start a trimmer for Huter grass correctly

How to start a trimmer motor for grass or lawn mower?

The new trimmer for the grass is simple in commissioning.

• Check the type of device motor. Trammers for grass are equipped with a 2- or 4-stroke engine.
• Buy oil for this type of motor. Gasoline for a trimmer for grass-AI-92/93/98, is sold at all gas stations.
• Mix oil with gasoline. Mineral oil is mixed in a ratio of 1: 34 with gasoline, synthetics. in 1: 50. Follow the tips of the trimmer manufacturer for the grass for the viscosity of the oil (see. label on the flask). often use all-season oil 5W-30. Do not use unverified car.
• Pour a small amount (for example, 0.5 liters) of the resulting fuel in the tank.
• Close the air conditioning by shifting the suitable lever (see. annotation).
• Turn the ignition key (or handle) to the “inclusive” position. without this, the trimmer will not start for the grass. Newcomers often make such a mistake.
• Skip a little fuel in a carburetor. if there is a manual “rocking” with a separate button or lever (see. annotation). We need 4-7 presses.
• Install Trimmer for grass On a flat surface.
• Carefully pull the starting cord until you feel its brake. Then abruptly pull it out, but not quite. Repeat this movement before 4 times.
• If the engine does not start, open the air damper again, it will flood the candles with a different gasoline during subsequent movements of the cord. Make 2-3 samples to start an open handbrake motor.
• If the motor does not start, close the damper and make a few more attempts to it Bind.
• After starting the engine, click on the gas lever, turning on the idle.

How to start a gasoline Trimmer for grass?

How to start correctly Trimmer for grass. the question that the owners are puzzled in the event of a breakdown of the device. And after the successful repair of the trimmer for the grass, the owner tries to avoid repetition of the same situation.

Starting the lawn mower for the first time or after a long downtime

The lawn mower differs from a trimmer for the grass in that a fishing line for a trimmer, but a mechanical gearbox or winch based on the gear equipped with a knife, acts as a cutter for grass. The knife drive is much more powerful than the forest mechanism. a powerful lawn mower is also used when cutting the bushes. Both Chinese and European law mmores do not differ in anything special when the declared capacity is real.

For lubrication of gear gears, Litol or solidol is used. Having checked the gearbox, prepare for the work and the engine itself. according to the above instructions. If the start has failed, the problem is already in the engine.

Prerequisites

The reason for which the trimmer for grass fails may:

• tank overflow;
• excessive fuel pumping into engines equipped with manual supercharger;
• wear in the motor of valves, cylinders, nozzles, fist pushers and other mobile parts;
• In the tanks, gasoline and/or oil ended;
• not in order of the spark plug;
• clogging of fuel or air filters;
• the valves in the motor were resolved or burned.

Fuel pouring through the openings for candles

If there is no manual pumping on the engine of the trimmer for the grass and the device did not start, pour a little fuel into the motor itself through candle moves. Make the following.

• Check if the fuel level is sufficient in the tank for draining a small amount of it. It takes only 20 ml.
• Remove the cap from the candle and unscrew it with a candle key.
• If the candle is polluted on the former use of the trimmer, rinse and buy it. There should not be any deposits on the electrodes of the candle. Do not damage the ceramic insulator of the central conductor. In the new trimmer, check the candles for the factory defect.
• Return the candle back and check the spark look (category between electrodes) when the starter triggers.
• Remove the candle again. Using a 20- or 50-cup syringe, pour 20 ml of gasoline into a candle hole from under a candle.
• Insert and fix the candle by setting the magnitude of its technological clearance at least and no more than a millimeter.
• Skip fuel using a button (or lever) of swinging. if it is on your model of a trimmer for grass. Press the button every 4 seconds.

Now try to start the motor. Close the air conditioning immediately after starting.

The main thing. Fuel mixture!

In this case, the remains of plastic plastic dissolved in the brutal environment are created in the combustion chamber so terrible things that you will definitely not be able. But you certainly remember how to store fuel forever.

What to do when the fuel was definitely normal, there is a spark, but a trimmer for grass does not start a gasoline? It is possible that you just flooded the candle with gasoline. In this case, it must be turned out, wiped with a clean rag and dry. By the way, it will be completely useful to check the candle for performance itself.

The carburetor of the lawn mower floods.

How can you drown the engine on a gas tank, to be inattentive. Just one awkward movement

After several jerks, he will start and stall, which is a normal phenomenon. Putting the damper to the working position, start the tool again and start working.

Why not start Trimmer for grass. the reasons

To determine why gasoline Trimmer for grass It is poorly started or constantly stalls, it is necessary to sequentially check the work of all the main components of the unit. It is especially important to do this after a long.term storage of a lawn mower. So, the main reasons for such a trimmer’s behavior for the grass are as follows:

• The culprit that the lawn mower is not started, there may be a poor-quality oil-Benzine fuel mixture. It must be prepared strictly according to the instructions. The savings here are not at all appropriate, since it can lead to the failure of the entire piston group of a trimmer for grass. Do not cook too much fuel mixture, as excess gasoline will lose their qualities over time.
• You should know that gasoline trimmers for grass of stamps such as STIHL, Husgvarna and some others do not start if they are filled with cheap gasoline with a small octane number. Therefore, for such units, it is necessary to use only high.quality high.octane fuel.

How to start a trimmer for grass gasoline Huter

How to launch a trimmer for grass. This is a question that the owners confuse in the case of failure of the device. And after the successful repair of the trimmer for the grass, the owner tries to avoid repeating the same situation.

The reason for the failure of a trimmer for grass is possible:

• Tank overflow;
• Excessive fuel injection into engines with manual supercharger;
• Wear in the engine of valves, cylinders, injectors, fist pushers and other moving parts;
• Gasoline and / or oil end in tanks;
• The spark plugs failed;
• Fuel or air filters are clogged;
• Incorrectly spelled out or burned valves in the engine.

The test begins with the presence of oil and fuel in both tanks and a small part in the engine system. The “empty” engine will not start, despite the full tank, and also overflow.

How to start a three.dimensional motor or bush?

The new trimmer for the grass is simple during commissioning.

• Check the type of engine engine. Trammers for grass are equipped with a 2- or 4-stroke engine.
• Buy oil for this type of engine. Gasoline for a trimmer for grass. AI-92/93/98, sold at all gas stations.
• Mix oil with gasoline. Mineral oil is mixed in a ratio of 1:34 with gasoline, synthetic. At 1:50. Follow the recommendations of a trimmer manufacturer for grass regarding oil viscosity (see. Label on the flask). The most commonly used polyhedral oil. 5W-30. Do not use unverified motor oils.
• Pour a small amount (for example, 0.5 liters) fuel into the tank.
• Close the air damper, moving the desired lever (see. Instructions).
• Turn the ignition key (or handle) to the “inclusive” position. Without this, the trimmer for the grass will not start. Beginners often make this mistake.
• Download a little fuel to the carburetor. If there is a manual “rocking” with a separate button or lever (see. Instructions). 4-7 clicks are required.
• Place a trimmer for grass on a flat surface.
• Gently pull the starter cord until you feel its braking. Then pull it sharply, but not completely. Repeat this movement up to 4 times.
• If the engine does not start, open the air damper again, otherwise the spark plugs are filled with gasoline during subsequent movements of the cord. Make 2-3 attempts to start the engine with an open manual brake.
• If the engine still does not start, close the shutter and make a few more attempts to run it.
• After starting the engine, press the throttle lever to activate idle.

Let the engine warm up. 5-10 minutes enough. Do not start mating grass immediately after a cold launch. The engine of the trimmer for the grass should start.

Starting the brush for the first time or after prolonged downtime

The lawn mower differs from the trimmer for the grass in that the lawn mower. This is not a fishing line for a trimmer, but a mechanical gearbox or a winch with a gear, equipped with a knife. The knife drive is much more powerful than the carriage mechanism. When cutting bushes, a powerful bush is also used. Both Chinese and European law mowers do not differ when the declared capacity is real.

Litol or solid oil is used to lubricate gears gearboxes. After checking the gearbox, prepare for the engine itself. In accordance with the above instructions. If when starting, a failure occurs, the problem is already in the engine.

Share fuel through the spark plugs

If there is no manual pumping on the engine of the trimmer for the grass, and the device does not start, pour a little fuel into the engine through the spark plugs. Make the following.

• Make sure that the fuel level in the tank is sufficient to drain a small amount. It will take only 20 ml.
• Remove the lid from the spark plug and unscrew it using the spark plug for a candle.
• If the candle is contaminated with the used trimmer, rinse and bake it. There should be no deposits on electrode electrodes. Do not damage the ceramic insulator of the central conductor. In the new trimmer, check the spark plugs for factory defects.
• Turn the spark plug back and check the ignition (discharge between the electrodes) when the starter lights up.
• Remove the candle again. Using a syringe with a volume of 20 or 50 cm3, pour 20 ml of gasoline into a hole for the spark plug.
• Insert and secure the spark plug, setting the value of its technological clearance at least and no more than a millimeter.
• Pour the fuel with the shift button (or lever). If this is in your model of a trimmer for grass. Press the button every 4 seconds.

Now try to start the engine. Close the air damper immediately after starting.

Checking the ignition system

If the trimmer for the grass has already been used, check the condition of the removed (currently) spark plugs, replacing it with any other. If, for example, when checking the spark plug, the ceramic dielectric broke, the electrodes bent, buy one, guided by the product code knocked out for the parts itself, and check it with a marker in the instructions at the trimmer. A spark plug without a insulator and / or with curved electrodes will not give normal sparks when triggered.

If the spark plugs are in order, but the fuel sparking is not observed, check the ignition coil with an ohmmeter (multimeter). Lack of indications (infinite resistance) is a sign of winding winding. If it sins from overheating due to a short circuit, the voltage for the spark malfunction will be insufficient.

Since he uses a very thin wire that converts 12.6 V from the battery of 30,000, it is very difficult to fix (rewind) even in the garage. The coil should be replaced.

We select the revolutions correctly

What speeds should be mowed to cut the lawn evenly? When is it better to increase or lower the speed? How much time you can hold high speeds? It should be noted that all these issues are relevant only for a gasoline trimmer for grass. The ethletric trimmer for the grass does not have the ability to choose the frequency of the engine, it goes almost as much as possible to its peak power and works on it while both power buttons are clamped.

If the device itself allows you to adjust the engine speed during operation, then the following will be optimal:

• minimum turns for working with lawn grass on a flat surface;
• average turns when using a disk for high grass and non.thick bushes;
• increased (maximum) revolutions for drilling bushes.

Do not start a trimmer for grass. how to find and eliminate the reason yourself?

If the motor motorcycles do not start, then this can talk about several tools of the tool at once. Start inspection and search for breakdowns should be from the spark plug. It will need to be twisted and carefully checked for clogging. If a thick layer of soil has formed on the tip of the part, then this indicates an excess of motor oil in the fuel mixture. To start a motorcycle, its owner must rinse the candle with gasoline and completely clean it from the car. Next, you need to damage the cylinder, pulling the starter’s cable several times. As soon as the candle dries, it needs to be screwed into the seat and try to get a motorcycle.

The reasons for the lack of launching of the motor can also be found in poor condition of the air filter. If, after prolonged use in the filter element, a large number of clogs have accumulated, then it will need to be cleaned and dried. If this could not be done, then the filter should be replaced. If a gas station is poorly started, then the cause of the malfunction often needs to be sought in the fuel hose. Due to banal wear or blow, he can break off, which will lead to pouring the fuel mixture. In this case, you will need to replace the hose. In the places of its joints, you will need to apply a uniform layer of silicone sealant.