How to get an elitech gasoline mower.

27th October 2022

Device and adjustment of the carburetor on benzocos and trimmers

A lawn mower or a trimmer for ICE grass requires not only a constant refueling of the fuel mixture of gasoline with oil, but also periodic adjustment of this fuel supply. The carburetor is responsible for the supply of fuel to the lawn mower cylinder, the effectiveness and performance of the tool depends on the good operation of which. If in the process of operation a faulty (abnormal) engine operation is detected, then the first step is to adjust the carburetor of the lawn mower. Before setting up a carburetor of a gasoline trimmer for grass, we will first figure it out with its design.

Lawn mowers are equipped with internal combustion engines of a two.stroke type. To supply a fuel mixture to the engine cylinder, a carburetor is used. In the design of gasoline units is a key element without which ICE is impossible. over, this carburetor differs from the car device not only in size, but also by the principle of operation. In particular, this difference is the presence of a membrane that plays the role of a gasoline pump. It is due to the presence of a membrane that the devices considered in the design of two.stroke internal combustion engines are called membrane.

Structurally, the entire mechanism is a small part, inside which there are channels, valves and membranes. The carburetor case is made of aluminum, and the internal device is shown in the photo below.

Before adjusting the carburetor of the lawn mower with your own hands, it is necessary to deal with all the constituent elements of the device in question. The carburetor of the lawn mower and a trimmer for the grass consists of the following details:

Venturi diffuser or nozzle. through this nozzle, air is absorbed into the system
Air damper. opens and closes the feed of filtered air
Fuel channel maximum revolutions
Fuel channels (nozzles) of the idle speed of xx and medium revolutions
Throttle. the opening value is regulated by pressing the gas
The fitting of the pulse channel. connects to the internal channel of the engine crankcase
Inlet fuel channel (fitting) (2). the supply of fuel from the gas tank is ensured
Membrane (4). is responsible for absorption of fuel from the gas tank
Fuel absorption valve from the tank (3)
Fuel supply valve to the carburetor channel (5)
Filtering element (6) or filter of fine fuel cleaning
Fuel channel (10)
The needle of the needle valve (14) is responsible for supplying fuel to the chamber of the control membrane
Camera. fuel mixture, which is supplied through nozzles and throttle ditch into the cylinder
The control membrane (18). is ensured by the manual fuel sucker primer
Lever connected to the membrane (17)
Idle adjustment screw (15)
The adjustment screw for the amount of fuel supplied to the diffuser (13)

Having an idea of how a carburetor is arranged inside, you have to deal with the principle of its work. A detailed description of how the carburetor works on a two.stroke internal combustion engine on the example of a chainsaw is described in this material.

How the gas mowing carburetor works or the principle of functioning

The adjustment of the carburetor of the Chinese lawn mower is completely identical with the setting of travokosylovs of European, and manufacturers. To cope with the task of adjusting the carburetor on benzocos and benzotrimers, you need to understand the principle of their functioning. How the carburetor works on a benzos, step.by.step and available described below.

The operation of the carburetor of the lawn mower begins with the supply of fuel through the channel, as shown in the diagram
The absorption of fuel into the carburetor occurs using a pulse channel connected to the engine card. Due to the vacuum of air, a flexible membrane is moved under the number 4 in the diagram above
Through valves 3 and 5, fuel supply occurs. The valve 3 is inlet, due to which the fuel is supplied to the sub.sector, and the valve 5. the exhaust
Further, the fuel moves through the channel and, passing the filter of thin cleaning, reaches the needle valve 14
The needle valve is connected by means of a lever with the control membrane 18
The needle valve is driven when exposed to the membrane. When it is necessary to pump up the fuel in order to start the engine, it is necessary to affect the soft cover of the manual pump. When exposed, the needle is opened, and the camera is filled with the fuel mixture
Когда же двигатель запускается (на холодную), то открытие иглы происходит за счет разрежения при закрытой воздушной заслонке. This vacuum affects the nozzle nozzles and high speeds on the membrane 18
The membrane acts through the lever on the needle valve, through which the camera is filled
After starting the motor, the air damper opens, as a result of which the engine operates on the depleted mixture, since the fuel is mixed with air
The fuel mixture with a filled chamber is supplied (sucked) through the nozzle jetlays and medium revolutions (when the engine is launched)
The throttle shift at the same time shifts from the original position by 10-15 degrees
When the work is carried out under load, then the fuel begins to enter the chamber through a nozzle nozzle, and at the same time the throttle shift turns to an angle up to 90 degrees (depends on the force of pressing for gas). In all operating modes, an air damper should be open, through which the fuel is mixed with air, and thereby there is an ignition of the mixture in the cylinder

The following shows the principle of operation of the carburetor of the lawn mower. Based on the scheme, you can not only deal with the principle of operation, but also identify breakdowns and other malfunctions of the mechanism.

When operating the tool, it is necessary to take into account the presence of another nozzle. This nozzle is located between the channels of the idle and full power. It is necessary in order to exclude a strong impoverishment of the mixture, which occurs in the case of the engine at an incomplete load. In such a situation, the occurrence of a back of a pair is not excluded. Through the additional channel (nozzle), fuel is sucked into the chamber, through which the fuel-air mixture is enriched. Below is an additional nozzle, which is indicated by the number 1.

Having an idea of the design of the membrane carburetor of Motokosa and the principle of work, it will not be difficult to configure it with your own hands. To adjust the carburetor of the lawn mower, adjusting screws are used. The scheme above shows two screws for configuration, but most modern models of gasoline trimmers are equipped with three screws. The presence of three setting screws allows you to perform a more accurate adjustment, while achieving stable and uninterrupted operation of the internal combustion engine.

It is interesting! What is the difference between a trimmer and a benzoca? Many people believe that a trimmer for grass is low.power electrical herb. However, a trimmer for grass is a generalized name for benzos, motorcycle and electric braids, as they are designed for general purposes.

What nozzle to use for mowing grass with a benzoca

The design of the gas station uses two types of cutting nozzles or milling. These are coils with fishing line, as well as steel or plastic disks. What is better to choose for work with a gas engineer. The site presents information on how to choose discs and fishing line for a trimmer for trimmers, as well as their types and design features. Briefly consider what types of cutting mills should be used on trimmers and benzocoses.

To prick soft grass, a fishing line for a trimmer is used, which is wound on a drum or coil. Lines for a trimmer, unlike metal disks, is used where the grass grows next to trees, houses, fences and other obstacles. The fishing line for a trimmer allows you to produce high.quality grass mowing near the obstacles, while without violating the design of the tool
Metal knives. have 2, 3, 4 or more cutting parts, through which the grip of rough grass and thickets are carried out. Practice shows that the thicker the sprayed thickets, the more blades should have a mill
Metal discs with small teeth in an amount of 40-80 pieces-designed to prickly prickly vegetation. It can be rough grass, weeds, thick thickets and even small trees. The larger the number of teeth on the cutting nozzle, the higher the effectiveness of the tool in question
Plastic discs. are used mainly on electritrimers or batteries

The choice of cutting milling cutters depends on the location of the tool. If it is planned to work in the personal territory, then a fishing line for a trimmer is selected, and for injection of grass in the field or steppe, discs with 3-4 blades or more, as well as disks with small teeth are used.

It is interesting! In most cases, cutters are not equipped with an instrument, so the buyer can independently decide what he needs. a fishing line for a trimmer or a steel disk.

How to fix a disk or a fishing line for a trimmer on a trimmer

The cutting mill is attached to the executive organ. The mounting location is called a gearbox. It is not difficult to cope with the task of installing a disk or coil. The principle of consolidating cutting discs on the trimmer is as follows:

The figured washer is originally fixed by using a hexagonal key
On the shaft set the disk
Then install the upper washer, and then tighten it by means of the fastener
It is necessary to rotate the nut through a special end key, which is usually equipped with each tool
The rotation of the nut is carried out in the direction counterclockwise
When rotating, it is necessary to jam the shaft with a hexagonal key

In the opposite sequence, the disk on the trimmer is removed and replaced. details on how to install a coil with a fishing line on a lawn mower is described in this material.

How to start a trimmer motor for grass or lawn mower?

The new trimmer for the grass is simple in commissioning.

Check the type of device motor. Trammers for grass are equipped with a 2- or 4-stroke engine.
Buy oil for this type of motor. Gasoline for a trimmer for grass-AI-92/93/98, is sold at all gas stations.
Mix oil with gasoline. Mineral oil is mixed in a ratio of 1: 34 with gasoline, synthetics. in 1: 50. Follow the recommendations of the manufacturer of the trimmer for grass for the viscosity of the oil (see. label on the flask). often used all-season oil 5W-30. Do not use unverified car.
Pour a small amount (for example, 0.5 liters) of the resulting fuel in the tank.
Close the air conditioning by shifting the desired lever (see. instructions).
Turn the ignition key (or handle) to the “inclusive” position. without this, the trimmer will not start for the grass. Beginners often make such an error.
Skip a little fuel into the carburetor. if there is a manual “rocking” with a separate button or lever (see. instructions). 4-7 presses are needed.
Install a trimmer for grass on a flat surface.
Carefully pull the starting cord until you feel its brake. Then abruptly pull it out, but not completely. Repeat this movement before 4 times.
If the engine does not start, open the air damper again, otherwise the candle will flood with gasoline with further movements of the cord. Perform 2-3 attempts to start an open handbrake motor.
If the motor does not start, close the damper and make a few more attempts to start it.
After starting the engine, press the gas lever, turning on the idle.

Let the motor warm up-5-10 minutes enough. Do not start mowing grass immediately after a cold start. a trimmer motor for grass should be used.

Mandatory actions before starting the operation of the device

Preparation for the launch of the mower is to verify the reliability of fixing all the elements and the preparation of the fuel mixture. As for the first, you should pay special attention to the fastening of cutting equipment. The lawn mowers are usually very powerful, and differ in a high speed of rotation of a knife or disk. Insufficiently fixed blade, first of all, can injure the user. In addition, it enhances vibration in the device, and this often leads to failure.

In most cases, lawn mowers are equipped with a two.stroke engine. Its refueling requires the preparation of a special fuel mixture.

There is no crankcase in such motors and is not provided for a separate system designed for oil lubrication. The role that these elements perform, takes on a freshly prepared combustible mixture. By the way, and this is important to take into account: the components are mixed from the calculation for one refueling. It is impossible to breed with a “margin”, and only fresh composition needs to be used.

Fuel consists of two components. This is oil and gasoline. Suitable fuel-AI-92, 93, 98. Proportions for minerals. 1:34, for synthetics. 1:50. You should familiarize yourself with the recommendations of the manufacturer of the lawn mower for the viscosity of the oil. There are special products for two.stroke engines and precisely with air cooling. The use of unverified or inappropriate options can lead to the failure of braids for grass.

The mixture should be diluted in a separate clean capacity. This cannot be done directly in the tank of the lawn mower! Half of the fuel volume and all the oil are poured into the container. Next, everything is mixed. Then the remnants of fuel are added. Mixed again. Now you can refuel!

You need to do this by putting the tool on the Earth: there is more likely that the liquid will not spill.

Gasoline trimmer for grass

The gasoline trimmer for grass copes with grass better than a lawn mower, since there are no difficult places for a gasoline trimmer for grass. But we should not forget that when using a gasoline trimmer for grass in difficult accessible places, the fishing line consumption increases due to the fact that it comes into contact with the fence, brick, curbstone, and t.D. Proper operation, the key to the long service of the gasoline trimmer for grass! Among the Elitech gasoline trimmers, there are models with a four.stroke engine. The gasoline trimmer for grass with a four.stroke engine differs in that oil and gasoline are filled separately. Such a trimmer for grass does not smoke, produces less noise, is environmentally friendly, which is not a little important.

Benzotrimmer (lawn mower, gasoline trimmer for grass, gasoline lawn mower) works without electricity, which is important when mastering new and large areas.

Basket (lawn mower, gasoline trimmer for grass, gasoline lawn mower) can have a power of up to 1,500 watts benzotrimers differ among themselves as a type of engine:

Benzotrimmers with a 4-stroke engine have greater power and produce less noise, have greater weight and dimensions, and are more expensive;
Benzotrimmers with a 2-stroke engine do not differ from previous models in functionality, but they produce more noise, cost cheaper.

Read how to refuel a fishing line for a trimmer to an electric trimmer for grass

Benzotrimmers can conditionally be divided into three groups: household, semi.professional and professional. The last group includes benzotrimers that can work continuously for 8 hours (shift).

Models

The most popular models for 2021 are:

Lawn mowed gasoline pro Husqvarna lb 553se. Speed of 5 kilometers per hour. Country manufacturer Sweden.
GAMPION LMH4412 lawn mower. The gasoline type of engine. The birthplace of the brand
Gasoline gasoline Bear Cat Echo WT190. Fuel tank volume 1 liter. The country of production of the United States
STIHL FS 40 Autocut Lawn mowed with 5-2. 38 centimeter processing width. The country of production of the United States.
Gasoline gasoline McCullock M51-150R Classic. Power 2 500 W. The homeland of the US brand.

Preparation of the fuel mixture and refueling

For the convenience of making fuel mixture, it is better to have a special canister. where one part contains gasoline, and in the other 2 stroke oil. We recommend getting similar, it is very convenient to use https: // ru-sad.RU/Prinadlezhnosti-Dlya-Sadovoy-Tehniki/Dlya-Benzopil/Kanistryi/

Next, take a measured container, with a scale applied to it, with its help you can prepare the mixture as accurately and quickly as possible. See in the instructions which brand of gasoline and 2-stroke oil https: // ru-sad.RU/Prinadlezhnosti-Dlya-Sadovoy-Tehniki/Masla-I-Smazki/recommended by the manufacturer of your lawn mower model. Pour gasoline and oil into a container for the preparation of the fuel mixture, according to the proportions specified in the instructions. Then the finished mixture neatly, through the funnel, pour the trimmer for the grass into the fuel tank. The ratio of gasoline and oil should be just the same as indicated in the instructions. This is a very important point!

Launching a lawn mower with an unfinished engine

For the first launch of the lawn mower, find the air damper lever and put it in position “Closed”. Turn on the ignition on the handle. If your model has a manual fuel pump, the people are called a suction, then click on it 3-5 times until you see the fuel mixture inside the primer. Now the tool is ready to launch. Put a trimmer for grass on a flat surface to ensure a stable position. Smoothly stretch the trigger cable until you feel its resistance, and then pull the cord with a sharp movement 3-5 times.

If the engine started after 5 jerks, then open the air damper. If this does not happen, still open the air damper (with an open damper and continuation of attempts to start the engine, the fuel flows a candle and you will have to dry it, and this is extra waste).

If the engine does not start, with an open damper, then close it to continue to pull the cord. The first launch may be quite difficult and demand up to 15 jerks. After the engine has begun to work, click once on the gas lever, so you will use idle. Now let the engine work and warm up. After that, it can be stopped by pressing the “Stop” button.

Step.by.step instructions for launch

In order to easily start a lawn mower, it is necessary to familiarize yourself with step.by.step instructions in more detail, but at the same time you also need to take into account the rules for refueling the device with fuel, as well as many other important nuances.

Only gasoline models need a refueling before starting, the engine of which will work incorrectly without correctly selected fuel or will not at all start. Therefore, having studied in more detail the technical characteristics of your device, you must also familiarize yourself with information about the finished fuel or with the preparation of a special mixture with your own hands.

In the latter case, it is necessary to observe the proportions that are specially designed for the correct functioning of the mechanism.

Sometimes synthetic oils are used for this. Such types of fuel mixtures have a lower cost, but practically do not differ in their quality characteristics. 5 liters of gasoline must be used per 100 grams of synthetic oil, so the mixture will have proportions. 1: 50.

Higher cost have mixtures with mineral oils, since they are considered more natural and environmentally friendly, but in terms of technical characteristics they only slightly exceed synthetic options. Proportions when using such materials will be 1: 35, that is, 3.5 liters of gasoline must be used per 100 grams of oil.

There are also options for gasoline lawn mowers, where the fuel tank is located separately from the crankcase for the oil, so there is no need to prepare the mixture.

But regardless of the model and type of fuel tank, refueling should be done the same way-not completely pouring fuel, but leaving 3-4 centimeters to the edge of the tank.

Launch

Depending on the model of the lawn mower, the launch will be made in different ways. Therefore, it is necessary to take this into account and, comparing with individual technical characteristics, proceed to connect the device and engine establishment.

And if with a manual model working according to the principle of ordinary braids for grass, everything is quite simple, then when starting a gasoline model, some difficulties may arise.

A gasoline lawn mower can be opened in two ways. with an unheated or with a heated engine.

Before you start an uninterrupted engine, you need to take care of turning off the ignition and transmission system, as well as scroll through the starting lever or starter motor shaft. After that, you can start starting, acting as follows:

First you need to turn on the ignition;
Then it is necessary to close the air damper;
After that, you can safely start starting the engine.

After starting, you need to install an idling on the device, using the gas lever. Then, using the same lever, you need to transfer the device to work at low speeds, thereby giving the engine the ability to warm up. After that, you can safely begin operation of the lawn mower at full power. It is worth noting that the launch of a device with an unheated engine is permissible, but further operation in this state is undesirable, since this will negatively affect the general state and the functioning of the lawn mower.

Launching a lawn mower with a warmed engine is much easier, since this process does not require preliminary preparation. The actions must be performed in the following sequence:

The control lever must be transferred to the fuel supply mode at the maximum level;
Then you need to start the engine;
After that, you can choose the necessary speed and start work.

These recommendations are suitable for any models, including manual lawn mowers that work on the principle of ordinary braids for grass.

How to launch after winter?

It may not be easy to start a lawn mower after the winter period, since most often devices of this type are stored in sheds where heating is not provided, which means that they are exposed to harsh winter climate, and sometimes sharp temperature changes. Therefore, it is necessary to approach this process wisely and take into account all the important nuances.

How to start a gasoline trimmer for grass

The process of commissioning the lawn mower, no matter you bought it now or got it after winter storage, the rules listed below will allow you to avoid the main errors that may damage the tool.

Suppose you just bought a gasoline trimmer for grass. Remove the instructions out of the box and see if all the parts of the lawn mowers that are indicated, you have. After that, you can start in the assembly.

Read how to wind a fishing line for a trimmer for a Stihl lawn mower

Launching a lawn mower with an unfinished engine

For the first launch of the lawn mower, find the air damper lever and put it in the “closed” position. Turn on the ignition on the handle. If your model has a manual fuel pump, the people are called a suction, then click on it 3-5 times until you see the fuel mixture inside the primer. Now the tool is ready to launch. Put a trimmer for grass on a flat surface to ensure a stable position. Smoothly stretch the trigger cable until you feel its resistance, and then pull the cord with a sharp movement 3-5 times.

Basic errors when starting

We list the main errors that beginners make when starting a gasoline trimmer for grass:

HOW TO TEST a Riding Lawnmower FUEL PUMP. The EASY WAY!

starting the engine when the ignition is turned off;
starting with a closed shutter with the number of jerks more than 5 times;
incorrect fuel mixture.

The first trigger

When everything is checked and the prepared fuel mixture is filled in the tank, the moment of the first launch of the trimmer for the grass until it is launched. To do this, follow the following manipulations:

Place the brush on a flat horizontal surface;
Transfer the throttle lever to a closed position;
We inject several fuel shocks for beginners in a carburetor;
Turn on the ignition;
Gently pull the starter cord until you feel resistance;
Then make a cord 3. 4 sharp jerks until the brush begins;
After starting, open the air damper.

How to start a gasoline trimmer for grass

The process of commissioning the lawn mower, no matter you bought it now or got it after winter storage, the rules listed below will allow you to avoid the main errors that may damage the tool.

Suppose you just bought a gasoline trimmer for grass. Remove the instructions out of the box and see if all the parts of the lawn mowers that are indicated, you have. After that, you can start in the assembly.

Launch of a heated engine

It is very simple. Put the switch to the working position and pull the cord to the start. If you do everything according to the instructions, then problems with the launch of a good lawn mower should not arise.

Launching a lawn mower with an unfinished engine

For the first launch of the lawn mower, find the air damper lever and put it in the “closed” position. Turn on the ignition on the handle. If your model has a manual fuel pump, the people are called a suction, then click on it 3-5 times until you see the fuel mixture inside the primer. Now the tool is ready to launch. Put a trimmer for grass on a flat surface to ensure a stable position. Smoothly stretch the trigger cable until you feel its resistance, and then pull the cord with a sharp movement 3-5 times.

Basic errors when starting

We list the main errors that beginners make when starting a gasoline trimmer for grass:

starting the engine when the ignition is turned off;
starting with a closed shutter with the number of jerks more than 5 times;
incorrect fuel mixture.

I Built the Worlds Fastest Electric Lawn Mower

How to start a gasoline trimmer for grass

The process of commissioning the lawn mower, no matter you bought it now or got it after winter storage, the rules listed below will allow you to avoid the main errors that may damage the tool.

Launch of a heated engine

Launching a lawn mower with an unfinished engine

Basic errors when starting

We list the main errors that beginners make when starting a gasoline trimmer for grass:

starting the engine when the ignition is turned off;
starting with a closed shutter with the number of jerks more than 5 times;
incorrect fuel mixture.

The start of work on starting brushes for gasoline

After starting, do not rush to immediately start a trimmer for the grass. Let the engine work at idle for 5 minutes. When heated, adjust the lever of the air damper with the help of the air damper lever so that the coil with a fishing line or knife does not rotate. As soon as the tool heats up, we completely open the air supply, transferring the corresponding lever to the “VCL” position, clicking on the gas trigger by 1/2 and holding for 20 30 seconds. Then we release gas, allow the trimmer to work XX for 30.40 seconds. In this mode, we continue for 10. 15 minutes. Then drown out and leave for 15. 20 minutes.

After cooling the bush cutter, we continue to work with the engine according to the previous scheme. Start hot, a trimmer for the grass should already have an external damper. Try not to hold the gas for a long time, since the moving parts of the tool only rub on each other. And do not let the engine stand for a long time, as it can overheat.

The next step is to launch a gearbox with a gasoline belt. To do this, select a plot with soft young grass. We squint for 5. 10 minutes, previously feeding 1/2. 2/3 of the full throttle. After a break for 20. 25 minutes. The cycle is repeated 3. 4 times.

Basically, the work of Kustorez according to the described algorithm is performed until the fuel mixture is completely developed in the tank. Then the tool is ready for continuous work. During this time, follow the temperature mode of the gearbox and engine. They should not overheat.

serious causes of malfunction

If, after a thorough inspection of the base nodes of the trimmer for grass, the cause of the device malfunction was never found, then you need to carefully inspect the engine and carburetor. In this case, three key problems can be distinguished at once, which are most often found:

Natural wear of the installed carburetor laying. The only logical exit from this situation is to replace a faulty part.
Cluster of garbage and soil in jettles or channels. For cleaning, you can use exclusively factory flushing or a regular stream of compressed air from the compressor. It is forbidden to use wire and sewing needles, since one incorrect movement can seriously damage the passing section.
Loss of the previous tightness. For a thorough check of this indicator, a classic household tonometer should be used, after installing a suitable pressure gauge. It is necessary to monitor the indicators: if any fluctuations were not recorded, then everything is fine, but when the pressure gradually drops, then some part in the carburetor failed.

If the carburetor used is serviceable, then the gasoline trimmer for the grass is not started due to the fact that the piston group was out of order. If during the inspection, characteristic chips, curvature or scratches were found, then the detail must be replaced. Experts recommend replacing piston rings. If a small backlash occurs when swaying a mounted connecting rod, then rings are subject to replacement, but this procedure is best entrusted to professionals.

Floods the candle on the benzos what to do the video

The owner of a summer cottage will not do without a lawn mower or a trimmer for grass. However, during its operation, of course, situations appear when this unit ceases to start for some reason. And the circumstances of this you will like a lot more. Let’s find out why the gasoline trimmer for grass does not start.

To find why the gasoline trimmer for the grass is poorly started or stalls, you need to check the work of all the main components of the unit in turn. In particular, it is fundamentally done after a long storage of the lawn mower. What you need, the main prerequisites for such a trimmer’s behavior for the grass are as follows:

Not starting on a cool trimmer for grass. We eliminate the cause

Use to clean the carburetor and special washing.

If the gaskets of the carburetor are worn out, you need to change them. And in case of violation of the density of this device, you will have to find a faulty part of the carburetor and change it.
A trimmer for grass may not be launched due to wear of the piston group. But to change such parts of the lawn mower is better in a car service. a fishing line for a trimmer for a trimmer for grass. which one to choose?

Immediately after buying a trimmer for grass for grass, we are faced with a lot of questions. how to use it, how to refuel it (if we are talking about a gasoline tool), well, it is clear which fishing line is better to choose for a trimmer. The answer to the last question is looking for the text of the article.

How to quickly remove the stump without uprooting?

Some gardeners at a certain moment are faced with the need to cut down trees that increase in this area. As a result of this, stumps remain, if the trees were of significant size, it is very problematic to uproot them. The text of the article is told about other methods of getting rid of stumps.

Sources:

https://moiinstrumentu.ru/ustrojstvo-i-regulirovka-karbjuratora-na-benzokosah-i-trimmerah.html
https://moiinstrumentu.ru/instrukcija-kak-kosit-benzokosoj-i-trimmerom-travu.html
https://anistart.ru/stanki-i-instrumenty/kak-pravilno-zavesti-benzokosu.html
https://ironplast.ru/oborudovanie/kak-zavesti-gas trimmer.html
https://ru-sad.ru/sovety-polzovatelyam/kak-zavesti-benzinovyy-trimmer/
https://banya39.ru/instrumentarij/kak-zavesti-motokosu-shtil.html
https://anistart.ru/stanki-i-instrumenty/obkatka-trimmera-2.html
https://anistart.ru/stanki-i-instrumenty/kak-pravilno-zavesti-trimmer-benzinovyj-video.html
https://xnb1a4ace.xnp1ai/info-baza/trimmer-zavoditsya-i-glohnet.html

Articles elitech, gasoline, mower