How To Properly Cut A 45 Degree Angle

25th July 2020

How to cut a tile at 45 degrees?
It is quite difficult to wash the tiles at 45 degrees on your own, but you can. How to cut tiles at an angle with your own hands? How do I cut tiles myself at 45 degrees?

Fundamental rules

When grouting tiles, it must be remembered that only clay can be cut, not reaching the glaze 0.5-1 mm. In this case, the corner of the tile will turn out to be nice and smooth, without damage or chipping.

Modern capabilities and the skill of specialists allow you to cut tiles at 45 degrees not only from the edge, but also in the middle of the product. To do this, the tiles must be measured and cut in accordance with the required size, and then cut at 45 degrees. To get a high-quality result, you should seal the cut edge with sandpaper.

Manual tile cutter

The manual tile cutter is popular not only among professional tilers, but also among hobbyists. Many models of such tile cutters are equipped with a special rotary base and a built-in ruler, which allow you to make a high-quality cut of tiles at 45 degrees. After inserting the tile into the tile cutter at a certain degree, it is necessary to align the mark on the tile and on the construction tool. Having lowered the handle down, you need to move it in a direction away from you with slow movements at the same speed and even pressing.

Slicing without special tools

It is not necessary to grind the tile using special devices. At home, you can easily hand-wash the tiles at 45 degrees. To do this, proceed as follows:

On the outer part of the tile (glaze), a line is drawn with a glass cutter;
Using an angle grinder, a small V-shaped groove is formed on the back of the tile, which is positioned across the width of the entire tile;
Then you need to gently break the bend of the cut and sand it with sandpaper.

How to use the miter box

A miter box will help you cut the plinth at a 45 degree angle. By the way, do you know how to use the miter box? The specialists of our portal have prepared a step by step for you.

Using a ready-made miter box

Self-made miter box

1. First, you need to assemble the box of the future tool. To do this, it is necessary to drill holes in its side walls, for future fastening with screws and, having smeared the ends of the parts with glue, connect them so that both walls are strictly perpendicular to the bottom and parallel to each other, after which we fix them with screws.
2. Using a protractor, mark an angle of 45 degrees with a pencil, if necessary, add additional mowing lines for the grooves. The most important part is the cuts, it is best to make them with the same hacksaw blade as you will be cutting products. It is necessary to cut by holding the blade, avoiding strong pressure on the tool, first we cut one side, then the other.
3. We start processing the material. With a clamp or screws, we fix the miter box on the working surface. At the place of the future cut on the plinth or board, we make a mark. How to cut at an angle of 45 degrees becomes clear if you press it tightly against the side wall and align the mark with the slot on the template. We insert the hacksaw into the groove and cut the workpiece, while the work of the blade is limited to cuts, which allows you to make a cut as smoothly and accurately as possible.
4. Before cutting the plinth, make sure that the corner of the room is really straight and, if it is not, you need to adjust the cutting angle of the workpiece. To do this, measure the inner corner of the wall joint, and divide the result by two. If you do not have a professional rotary miter box that can change the cutting angle by the required amount, then to achieve the result, you need to saw additional grooves at the desired angle in a homemade miter box. This way you can cut the skirting board for the most accurate alignment.

Now you know how to cut a workpiece at a 45 degree angle. Perhaps the time has come to move from theory to practical action. The team of the mebeldok.com portal is sure that you will definitely succeed. Stay with us!

News

Pipe cutting at an angle of 45 and 90 degrees

If you need to cut the pipe at an angle of 45 degrees, which is more often required when laying water and heating pipes. Steel, cast iron pipes that are cylindrical in shape are often used. In the installation work, rectangular or shaped pipes are used. However, the pipe of the angle grinder should be cut correctly so that it can be easily connected later. Therefore, you should carefully mark the pipe.

Some craftsmen try to mark the place of the cut using a tape measure, but we warn you that the result is likely to be negative. And for a positive result, consider the following professional recommendation.

Take a sheet of paper or cardboard, preferably A4, fold it diagonally and wrap it around the pipe where you plan to cut it evenly. The edges of the paper should be exactly aligned with each other. And the side of the paper that is closer to the end of the pipe was perpendicular to the axis. Then mark the cut line in a circle.

If you need to cut exactly at an angle of 90 degrees, then solve the problem quickly using paper or masking tape again. Wrap around the pipe so that the ends match. Make even lines and saw off.

How to cut a profile pipe straight?

Masters advise using a square when cutting a profile pipe. To do this, apply the square in turn to the sides, and turn and mark with smooth movements. After action, fix the pipe and cut. Prepare yourself a template that will come in handy in the future and save time. It is better to produce an angle grinder, so the cut will be smoother.

How to cut a cast iron pipe?

When working with a cast iron pipe, keep in mind that it is a brittle material. Therefore, we will point out a method with which it will be possible to cut such a metal without damage.

Before starting work, make notes for the cut, just like with steel pipes. Place a piece of wood for support. Run your angle grinder around the circumference of the pipe making small cuts. Then take the chisels, insert them into the groove and hit hard with a hammer. Note that bakelite-based cut-off wheels are used to cut cast iron pipes.

If you don’t have an angle grinder on hand to cut a cast-iron sewer pipe or other purposes, use a metal hacksaw, chisels or special pipe cutters.

How to cut a gas pipe?

Cutting a gas pipe is dangerous, so it is best to entrust it to professionals. But if you are confident in your strength, then take an angle grinder, welding, hacksaw, gas welding to cut the metal.

Shut off the gas riser before work. Then release the rest of the gas from the pipe. To do this, light the gas in the burners and wait for it to go out.
After the actions taken, cut. Using the welding method, the metal base burns when exposed to high temperature. The result is fast and effective. But remember that cutting or rooting gas pipes again takes experience.

How to cut a pipe straight with an angle grinder?

When dealing with construction or plumbing tasks, you need to know how to cut the pipe straight from an angle grinder. In the article, we will consider quick and easy ways to properly cut an angle grinder pipe so that the result is perfect.

How to trim a ceiling plinth using a miter box template

Something resembling a miter box can be done by applying the required cut angles to paper, cardboard or wood. Draw two parallel mowing lines, locate the center, and then set the required angles using a protractor. The advantage of this method is that you can postpone any angle, including more than 90 degrees. Of course, before cutting the corners of the ceiling plinth, you must first check the angle between the walls with a corner and measure it with a protractor.

The technique for cutting a ceiling plinth using a painted miter box is exactly the same as using the miter box itself. We press the plinth plank to one of the parallel lines, then set the hacksaw at the desired angle, which is already outlined, and cut it off.

How to cut a corner of a ceiling plinth using a miter box

The miter box is a simple carpentry tool that allows you to cut the workpiece at the desired angle. Most often it is a tray made of plastic, wood or metal with vertical slots for cutting at an angle of 90 ° and 45 °. There are also more complex miter box designs. For cutting at angles of 90, 60 and 45 degrees. For more professional work, a miter box with a swivel mechanism is used, where the hacksaw can be fixed at any angle to the workpiece.

How to cut a skirting board with a miter box. Inner corner:

We apply the plinth to the ceiling, measure the required length.
Then we install the plinth plinth in the miter box so that the position coincides with the position of the plinth on the ceiling.
The plinth strip should be pressed against the far wall of the miter box.
We hold the plinth with your left hand.
We choose such a position of the hacksaw when the angle is 45 degrees and the handle of the hacksaw is as close as possible to the left hand.
We cut the workpiece without making excessive pressure on the saw.
The next step is to trim the plinth striker. We also install it to the far wall of the miter box.
Press and hold with your right hand.
We choose such a position for the hacksaw when the angle is 45 degrees and the handle of the hacksaw approaches the right hand.
Cut off the skirting board.

Next, we join the trimmed plinths and check the cutting accuracy. For a more accurate orientation, they also say that to complete the inner corner, it is necessary to start cutting from the front of the skirting board. Wooden skirting boards will most likely need to be filed after trimming.

How to cut a ceiling plinth with a miter box. Outside corner:

In order not to be mistaken with the dimensions, it is better to start by marking the inner corner, and then cut out the outer corner. Otherwise, a situation is possible when the planks may not be enough in length.
It is necessary to attach the plank to the ceiling and outline the dimensions.
Install the plinth strip and press it against the nearest wall.
Hold it with your left hand and choose a position for the hacksaw at an angle of 45 degrees, when the handle approaches the left hand.
We cut off the workpiece.
We install the striker to the nearest wall, hold it with the right hand.
We set the hacksaw at a 45 degree angle when the handle approaches the right hand.
We cut off the workpiece and join the corner.

Trimming the workpiece with a miter box is only suitable if the angle between the walls is even. 90 degrees. If the accuracy is poor, you will have to use other methods.

How to trim the corner of a ceiling plinth using ceiling markings

Marking the skirting board on the ceiling also allows you to cut the corner straight and precisely. The only drawback of this method is that it is difficult and inconvenient to keep the plinth strip suspended during the cutting process. Otherwise, you can mark the cutting angle in this way even more accurately than in other ways. Applying the plinth to the installation site, all wall flaws and deviations in the angle size are immediately taken into account.

Cutting the corner of the skirting board:

The first step is to cut two workpieces at a 90 degree angle.

Then we first apply one plank, resting its end against the perpendicular wall. We draw a line on the ceiling, outlining the contour of the plinth.

We remove this bar and apply a striker, also resting its butt against the wall. We outline the line.

The intersection of the marked lines will be the mark at which the skirting board needs to be cut.
Again, we apply each bar in turn and mark the cutting point on them.
We draw the line from this point to the other edge of the plinth.

We cut off the skirting boards along the outlined lines, join them and apply them to the installation site. Note that this method makes it easier to cut inside corners.

Sources: