How To Run The Trim Carver

The correct first start-up and running-in of the lawn mowers are very important steps in the start of operation of a new tool. On the one hand, they make it possible to preserve the motor resource of the gasoline engine laid down by the manufacturer, since at this stage grinding of moving units and parts takes place. On the other hand, the first necessary skills for working with a trimmer are acquired, if we are talking about the first tool in my life.

How to run the trim carver

  • Preparing for the first launch of the lawn mowers
  • Inspection and lubrication of the lawn mowing gear
  • Preparing the right fuel mixture
  • First Trimmer Trigger
  • Getting Started Running Lawn Mowers

Preparing for the first launch of the lawn mowers

Before you make the first start of the lawn mowing, you need to perform a series of sequential actions:

  • Inspect the gearbox and grease it;
  • Prepare the correct fuel mixture.

Inspection and lubrication of the lawn mowing gear

Checking the gearbox before starting the gas trimmer must be done on a regular basis. The absence of lubricant or its small amount increases the friction of the gear transmission of the gearbox operating at rather high speeds. As a result, overheating and gears occur. The lawnmow reducer fails. Prevent the occurrence of such damage during operation and helps regular inspection.

If, before starting the gas spit, an insufficient amount of grease in the gearbox or its absence is detected, “LITOL” is put into the housing. To do this, it is necessary to unscrew the screw on the bend of the gear housing and syringe “LITOL” in the amount of 1-2 ml.

Preparing the right fuel mixture

Before you start running in a new lawn mowing engine, you must also properly prepare the fuel mixture. As you know for two-stroke engines, it is prepared from special two-stroke oil and gasoline, taken in certain proportions. You can find out the proportions from the instructions that came with the tool or on the lubricant label. From the instructions you will also find out the recommended type of fuel, as well as the recommended type of engine oil.

Going to run in a new lawn mowers, many are faced with the problem of preparing the fuel mixture. And the reason for this disagreement in the instructions of the manufacturer of the tool and in the instructions of the manufacturer of motor oils. The former recommend a proportion of 1:25. The second recommend 1:50. Who to believe? How to proceed?

According to experts, if in the instructions for the lawn mowers the manufacturers write the proportion 1:25 or 1:30, then most likely this is either a cheap tool with poor cooling, or the manufacturer does not know which oil the consumer will add. But here it must be understood that an excess of lubricant does not affect the performance of the trimmer in the best way. Excess oil does not completely fade during engine operation. It cokes, clogs the cylinder and piston.

What to do in this situation when running a new tool? An ideal option would be to buy exactly the oil recommended by the manufacturer of the lawn mowers. In the case of run-in motors, when it is not possible to purchase the recommended oil, it is best to purchase a good Husqvarna two-stroke oil for the gasoline tool of the same name. It is not cheap, but it lasts for a long time. It must be disturbed as described in the instructions on the bank.

First Trimmer Trigger

When everything is checked and the prepared fuel mixture is poured into the tank, the time comes for the first start of the trimmer before it is run-in. To do this, perform the following manipulations:

  1. Place the lawn mow on a flat horizontal surface;
  2. Move the choke control lever to the closed position;
  3. We pump up a few strokes of the primer fuel into the carburetor;
  4. Turn on the ignition toggle switch;
  5. Gently pull the starter cord until you feel resistance;
  6. After that, make a cord 3 4 sharp jerks until the lawn mowing starts;
  7. After starting, open the air damper.

Getting Started Running Lawn Mowers

After starting, do not rush to run the trimmer immediately. Allow the engine to idle for about 5 minutes. While warming up, adjust the choke lever with the choke lever so that the spool with fishing line or knife does not rotate. As soon as the tool warms up, we completely open the air supply by transferring the corresponding lever to the “ON” position and squeeze the gas trigger by 1/2 and hold for 20 30 seconds. Then we dump the gas, let the trimmer work for XX for 30.40 seconds. In this mode, we continue for 10 15 minutes. Then we muffle and let rest 15 20 minutes.

Having cooled the lawn mowing, we continue to run the engine according to the previous scheme. Start on a hot, trimmer must already have an open air damper. Try not to hold gas for a long time, as the moving parts of the tool only rub against each other. And do not let the engine idle for a long time as it can overheat.

The next stage is the running-in of the gasoline braid gearbox. To do this, select a site with soft young grass. We mow 5 10 minutes with pre-gas for 1/2 2/3 of the full throttle. After we take a break for 20 25 minutes. The cycle is repeated 3 4 times.

In general, running the lawn mowers according to the described algorithm is performed until the fuel mixture is fully developed in the tank. After which the tool is ready for continuous operation. In the process, monitor the temperature conditions of the gearbox and motor. They should not overheat.

Source

The Carver trimmer in the domestic consumer market has become a real godsend for gardeners and gardeners. These are reliable, affordable and high-quality trimmers that work both from a 220 V network and from a gasoline engine.

The company’s engineers equipped trimmers with two, four stroke engines and an efficient cooling system. All products of the Carver trademark are convenient during operation. Excellent ergonomic characteristics contribute to this. For a more detailed acquaintance with the company’s products, check out the quality characteristics of the most popular Carver models.

Trimmer “Cover” GBC 31F model

In the model, cleaning the air filter is quick and easy. Management is quick and easy. The kit includes a special cutting disc for mowing high weeds and shrubs. Main technical specifications:

  • Power is 800 W;
  • The cylinder has a working volume of 31 cubic meters. Cm;
  • The weight of the trimmer assembly is 8.1 kg.

It is worth taking into account the fact that the engine cylinder is chrome plated, which significantly increases the life of the engine.

Lawn mowers “Carver” model GBC 31FS

The unit is equipped with an engine that runs on gasoline with an air cooling system. It can be used for mowing grass, vines, weeds. The main characteristics include:

  • The engine runs in four cycles;
  • Chrome cylinder;
  • Rotation speed of 7000 rpm;
  • Power is 800 W.

The model kit includes two cutting elements: fishing line, metal knife.

Lawn mower “Carver” model 052 PRO

This model is intended for professional use, in this regard, it is very popular among utility companies. The peculiarity of the model is that it is equipped with a rod with a diameter larger than the average, a rigid shaft, roller bearings and a powerful gearbox.

Qualitative characteristics:

  • Two-stroke gasoline engine;
  • Power 2300 W;
  • The engine cylinder has a displacement of 25 cc. Cm.

The unit is equipped with fishing line and a special knife

Lawn mowers “Carver” model GBC 043M

The model is characterized by an improved engine housing, high-quality cutting elements and improved ergonomic properties. This trimmer belongs to the category of professional garden tools.

Qualitative characteristics:

  • Power 1.7 l. With.;
  • Cylinder volume 43 cc cm;
  • Trimmer weight 6.7 kg.

The drive in the model is carried out using a hard shaft.

Model GBC 043MС

In order not to make a detailed description of the model and understand all its advantages, you just need to familiarize yourself with the technical characteristics that this trimmer has:

  • Powerful bar;
  • Steel shaft with bearings;
  • Special carbide disk;
  • Powerful gearbox;
  • Beveled strip width 23 cm;
  • Power equals 2.2 liters. With.;
  • The presence of brakes for the engine.

A model with such quality characteristics is ideal for professional use. Sometimes the buyer has a question: “How to maneuver a powerful bar and how to lubricate the bar?”. The answer is simple: “The maneuverability is excellent, the lubrication process is simple!”.

Source
Grass Trimmer ,