How To Thread The Line Into The Auto Trimmer Spool
How much line will you need?
For normal functioning of the trimmer, 3-4 meters of material is enough. The length of the thread depends on the dimensions of the spool. The larger it is, the longer the line.
Two cutting elements
If your trimmer has a spool with not one, but two cutting elements, unwind the required amount of fishing line and thread the thread through the hole, the fishing line should be divided into 2 parts equal in length. Then start winding 2 pieces at the same time. When almost all of the line is wound, leave short ends and clamp them in the grooves. This method is suitable for a single groove spool.
If the device has not one, but two grooves, you need to insert the fishing line in a different way. fold the cut thread in half, at the end you will have a loop. You need to insert this end into the groove, it is located between the two grooves. Each groove has one end. Assemble the coil in the same way as in the previous case.
Line selection
First of all, you will need to choose the correct line. You should not do it “at random”, as it all depends on the model of the unit. Pay attention to indicators such as the diameter of the thread, as well as its cross section. You can find information about the diameter in the instructions for the trimmer. The second indicator (section) depends on what kind of work you are going to perform. If this is a soft young grass, a round one is suitable, if it is hard. choose a square or 5-sided section.
How to thread the line into the auto trimmer spool
You don’t have to work on site for hours on end to trim and tidy your lawn. With any volume of work, such a device as a trimmer will cope as quickly as possible. This type of technique can cut grass of any length and density, it all depends on the chosen model. In order for the unit to fully work and perform its main function, you need to refuel the line, otherwise the trimmer will not be able to complete the task.
How to properly fill the line in the trimmer: instructions
If you set the line incorrectly, the unit may break down and you will have to fork out to repair it. Therefore, before proceeding with the procedure, be sure to read the detailed step-by-step instructions. It’s easy to learn how to do this and in a few minutes you can go to mow the grass.
How to tuck the line into the trimmer:
- First, you need to remove the nozzle that is located on the gearbox. This is easy to do: the connection is the hole located on the side of the bottom washer and the recess. You can find notches on the axis. Be sure to insert a screwdriver to prevent the shaft from turning. When removing the nozzle, you need to twist to the right, not to the left. Disassemble the coil. sink the clips located on it into the body, then gently squeeze the edges.
- How to handle the line automatically? You need to handle it as carefully as possible, otherwise a spring will fly out of it (the same applies to fishing line with a semi-automatic mode). Hold the parts with your fingers and take your time.
- Spool with a through hole on the body. you need to pull the line through both holes (outer and inner). Then turn the button and release the thread.
- If the reel functions only with 1 cutting element, the procedure is quite simple and quick. You will find a small hole in the inside of the spool that will keep the thread in place. You need to insert the end of the thread into the hole, then start winding. This should be done in the opposite direction in tone to the movement of the coil. Take a closer look. perhaps your reel model has an arrow, it indicates the direction in which you need to wind.
- The end of the thread is fixed with a groove located in the inner part of the bobbin. Leave a long piece of line outside.
- If your model does not have a groove, hold the end of the thread with your hand, then install the top of the spool and thread the end of the thread into the hole.
- Place the spool in the trimmer and get to work!
How to properly thread the line into the trimmer spool:
If the instructions above didn’t work for you, check out this. You will clearly see how to thread the line step by step.
The first way
Line bent in half
The prepared segment (in this case, it is 4 meters) is bent approximately in half. one segment should be 15-20 cm longer, and inserted into a special slot located on the dividing partition.
The line is inserted into the slot
The line is wound in the direction determined earlier. This is done in an interference fit, the line is neatly distributed. In this case, you need to wind a segment that is longer in the section that is closer to the button.
There are designs that do not provide for dividing the coil into two sections. This does not change anything, the line is wound in a similar way. You just need to make sure that the segments do not overlap with each other.
The first should end the segment that is located at the bottom of the coil, i.e. The one closest to the fixing holes.
This tip fits into the corresponding hole in diameter. The line is securely fixed.
The line is securely fixed
A long segment is wound another half turn. There he is similarly fixed. In this case, the segment crosses another section of the coil.
A long segment is wound another half turn
The fixed ends of the coiled line are inserted into the holes in the trimmer spool body.
The coil is attached to the body. The ends of the fishing line are pulled up with effort so that the fishing lines previously fixed in the holes of the reel jump out from there. It is easily identified by the characteristic sound (click).
The ends of the line pull up with effort
Button spool snaps into trimmer spool housing.
The line was changed successfully. In this case, you need to put it back on the trimmer and you can start mowing the grass.
It should be repeated, there is no need to remove the spool from the trimmer. this was done for clarity of the process of replacing the fishing line. You can disassemble the spool in place, wind it on the spool and put it back.
Line replacement completed successfully
Tips so that they do not hit on the trimmer cover can and should be trimmed.
Coil with two working antennae
In this type of spools, you should determine the number of grooves for winding the line, lying on the inside of the spool:
- One groove. both tendrils are wound together in one groove;
- Two grooves. each tendril is wound on an individual groove.
For both cases, a line with a length of 2-3 m is taken.In single-groove reels, the line is pulled into a through hole, its ends (antennae) are folded together and aligned, after which they are wound in the opposite direction of rotation of the bobbin on the rod side. inside the arrow usually indicates the correct direction of winding. If there are fixing grooves, the ends of the fishing line are threaded through them or held with the fingers of the free hand, they are threaded into the through hole of the outer half of the bobbin, the spool is closed and attached to the trimmer bar.
The difference in line winding in two-groove spools is that initially a 2-5 m long line segment is folded in half (to determine the middle fold), and the fold loop is inserted into a special groove between the grooves. Both antennae of the fishing line are wound each along its own groove, fixing the antennae and assembling the coil is similar to the one discussed above with one groove.
The first execution of this procedure, perhaps, will seem long and rather laborious, but with time and experience this task will be solved much faster and easier.
The following will clearly show how to thread the line into the trimmer reel and wind it correctly. this operation is not difficult and with some patience it will certainly be crowned with success:
Preliminary preparation
First of all, to wind the fishing line, you need to remove the spool (bobbin, spool) from the trimmer. specific actions will depend on the complexity of the configuration and the type of the product itself:
- Small electric trimmers with a working engine and bottom coil usually have side buttons on either side of the bobbin. When pressed at the same time, the upper part of the spool together with the inner content for winding the line is detached, while the lower part remains on the trimmer. It is advisable to disassemble the bobbin on a flat, smooth place so that the spring included in the structure does not jump out and get lost;
- Electric and gasoline trimmers with a curved bar without the possibility of installing a knife, as a rule, have spools with a special wing: in such designs, hold the spool in a stationary position with one hand, and rotate the locking reel on the rod with the wing nut counterclockwise with the other. After disconnecting the nut, the entire bobbin is removed.
- Electric and gasoline trimmers with the ability to install the knife on a straight bar (for example, Stihl trimmers) have a hole under the reel. To keep the rod stationary, a screwdriver or other suitable object is inserted into this hole and, with slow rotation, such a mutual arrangement is achieved when the screwdriver enters the hole and the bobbin is fixed. After that, the coil body is scrolled clockwise (with a left-hand thread) and removed from the trimmer.
For the second and third cases, the coils, depending on the design, are disassembled in different ways. In bobbins with a lamb, a lamb is unscrewed, in coils with latches, the latches are pressed and one part of the coil is released from the other. If the halves of the bobbin are connected by thread, then it is enough to turn them by hand in opposite directions until they are completely unscrewed.
Single-barbed trimmer coil
Single-barb lawn mowers reel
Many owners and experts note the ease of use and ease of refueling the bobbin with one mustache. Depending on the manufacturer, the length of the threaded line can vary from 2 to 5 meters. The end of the line is inserted into the head into a special technological groove or hole, and the winding is carried out in the direction opposite to the working rotation of the bobbin. Most reels have arrow marks on the outside of the body that indicate the direction of travel of the trimmer reel.
After winding, you need to leave a free end of 15-30 cm to enhance the centrifugal force, which is decisive when removing the trimmer line in automatic and semi-automatic spools. We pass the left end through the working hole of the coil and assemble the head.
Preparing for replacement
We disassemble the trimmer spool
For clarity, the mowing head (spool) was removed from the lawn mower. To replace the fishing line, you do not need to remove it, everything is done locally. It doesn’t take long.
We disassemble the trimmer spool. it rests on the latches. Remove the cover by pressing on the latches. If you do not have enough effort to do this with your hands, then use a screwdriver.
The spool consists of the following:
- Spring case
- Cover with locking latches
- Reel with button
The principle of operation is as follows. By pressing the button, the spool presses on the spring and comes out of the locking grooves in the spool cap. Holding in this state, the reel can be twisted, thereby adjusting the length of the line. When the button is released, the body spring returns the coil to its original fixed state.
Disassembled trimmer spool
On the bottom of the reel there are several holes for different diameters of the lines. They may differ from trimmer manufacturer. In some cases (like here) they are signed, in others they are not.
These holes are needed to fix the line when replacing it. After winding the fishing line on the bobbin, the ends of the latter are inserted into them. This is necessary so that the scaffold does not unwind when the coil is installed in the trimmer body. In other words, it makes it easier to change the line.
Holes for fixing the line
There are models without specifying the diameter of the consumable. Then, in order to find out what the maximum diameter of the scaffold can be used, it is tried on along the holes for the outlet of the fishing line from the trimmer spool body (see Figure below).
Fitting on the holes of the line output
The reel has two line sections separated by a baffle. They may not exist. They are needed only to delimit and facilitate the winding of the consumable.
Two sections for line
First, they are determined with the required length of the loess. The latter is wound into one of the sections of the coil so that it does not go beyond its limits. In this case, 3 mm was wound, the length turned out to be about 2 meters. THOSE. For two sections, you need a 4 meter segment. this is for the 1st method. For the second method, you need two segments of 2 meters each.
Determining the required line length
Now you need to figure out which way you need to wind it. To do this, many trimmer manufacturers apply special designations to the spools, such as in the figure below.
Special designation on the reel
If no such designations were found, then you need to pay attention to the spool body. There is necessarily an arrow that indicates the movement of the mowing head. The line is wound in the opposite direction.
Bobbin case designation
Trimmer head with two antennae
Double flute head
After removing the spool from the spool body, we determine the number of strands for winding the line (1 or 2). There is no fundamental difference between bobbins with one and two grooves, but if carelessly threading into the twin groove, there will be operational problems. Due to the likelihood of interweaving adjacent lines of the tool, a situation may arise when, after wear of the working antennae, it is impossible to remove new.
Regardless of the number of streams, a fishing line with a length of 1.5 to 3 meters is taken for refueling. Winding must be done in the opposite direction to the rotation of the head, since winding in the direction of travel will lead to the fact that the line will not be removed from the reel. After the fishing line is tucked into the trimmer coil, thread the free ends (15-30 cm) into special holes. Next, we assemble the head in the reverse order of disassembly and check the operability. Do not worry if the ends of the two antennae are very different in size, because when you start the trimmer, the knife installed on the protection will cut off the excess.
Coil with one working antenna
The simplest option and uncomplicated sequence of actions:
- The dimensions of the reel and the length of the original factory winding determine the recommended length of the line for winding. 2. 5 m.
- One end of the line is inserted into the fixing technological hole located inside the spool.
- The fishing line is wound on the drum in the opposite direction of the spool rotation on the trimmer product. as a rule, on the inside of the reel, an arrow indicates in which direction the winding is carried out.
- A small section of the line is left free to lead it out. it is fixed in a specialized groove on the inside of the bobbin, designed to hold the winding when assembling the bobbin into working condition.
- The left end of the line is passed through the hole in the outer part of the reel.
- The bobbin halves are assembled and put on the trimmer bar.
How to wind line around the trimmer cutter head or lawn mowers
How to thread the line into the trimmer spool
The warranty production of the factory trimmer refueling will inevitably require line replacement. Having a very rough idea of how to thread the line into the trimmer reel on their own, beginners are reluctant to take up this business. However, with some skills, mastering this simple science does not present any difficulties, and the similar instruction presented below will make this process as easy as possible.
Replacing the line in the Patriot trimmer
Display of line replacement in Patriot pt 535 trimmer reel.
Option number 1
To remove the trimmer head, you will need to completely disassemble it.
How to wind line on a trimmer reel: key points
A gasoline or electric trimmer is an indispensable tool in the arsenal of a modern summer resident or owner of his own home.
Thanks to these garden tools, even a large garden plot can be mowed with ease.
For an inexperienced user, the first operation to replace it will seem problematic and time-consuming, since the developers often do not fully reflect the instructions for replacing the fishing line in the operating manual.
What can be used instead of fishing line
Many trimmer users are wondering: what can replace the default cord used in this kind of machines? Begin unsafe experiments by placing metal or copper wires, metal ropes or strings, and regular fishing line in the mowing head.
If you install a metal cable instead of a fishing line, the trimmer turns into a dangerous device not only for the user, but also for others. This fact is explained by the fact that during the operation of the unit, the steel cable will gradually work, its ends will unravel, and small pieces of wire will fly in different directions at high speed.
And if you accidentally hook your or someone else’s leg while working with a steel cable (wire), then a strong and deep tissue incision, and in some cases amputation of toes, is guaranteed. It is not in vain that the manufacturer uses nylon for these purposes, since it is quite lightweight and durable, and when it comes off it does not fly far and cannot cause injury.
In practice, the installation of a regular line is justified if the user is going to mow the grass near the fence, especially if he is from the netting. In this case, in order to protect the standard and sometimes expensive cord from wear and tear, it is changed to a fishing line, which is not a pity. Usually, in order to change the line to line, it must be selected with the greatest thickness. 2-3 mm.
Automatic line winding to a spool
There is a type of reel in which the automatic mechanism winds on its own. from the user it is enough only to correctly fill the line.
The fishing line is passed through a hole on the inner part of the body, its antennae without winding are passed through the hole on the outer body, the reel is assembled, and when the winding button is rotated, the fishing line inside is wound independently. Running in a huter petrol trimmer.
In such a spool, it is impossible to make the winding wrong: the mechanism itself will determine the correct direction, since it can only rotate in one direction.
Trimmer head with automatic line threading
Types of trimmer heads
Some models on the market have a reel with an automatic winding mechanism. It is enough for the owner to properly thread and fix the ends in the head, and the winding operation will be performed by the tool itself when it is turned on.
It is almost impossible to wind the line incorrectly into a trimmer with such a head, since the coil independently determines the position of the antennae.
How to wind line on a trimmer reel: key points was last modified: June 28th, 2018 by Admin
Threading the line into the trimmer
The main question is how to properly wind the line on the trimmer spool, securely fixing it there?
In the case of a device with one antenna, up to four meters of fishing line is unwound, one end is inserted into the hole inside it, which fixes the fishing line, and moved in the direction indicated by the arrow. The end of the thread is fixed in a groove inside the bobbin so that it does not unwind during assembly. If there is no groove, then this free end is fixed with a finger. Then the coil is assembled.
How to thread a trimmer coil if it has two antennae? In this case, check how many grooves there are on it. one or two. In the first case, both antennae are directed into a common groove, if there are two of them, then each of them. into its own.
The ends of the thread are inserted into the grooves or held with a finger, the device is assembled and attached to the trimmer.
In a spool with two grooves, the same piece of thread is folded in the form of a loop, sent to the groove between them and the ends are wound simultaneously. Then repeat the previous assembly.
With semi-automatic winding, the bobbins operate as follows. The line is passed through the hole inside, its ends are fixed in the holes on the body, collect it and press the button.
The thread can be easily wound in the correct direction.
See: How to Insert Line into Trimmer
Single-barbed trimmer coil
Single-barb lawn mowers reel
Many owners and experts note the ease of use and ease of refueling the bobbin with one mustache. Depending on the manufacturer, the length of the threaded line can vary from 2 to 5 meters.
The end of the line is inserted into the head into a special technological groove or hole, and the winding is carried out in the direction opposite to the working rotation of the bobbin.
After winding, you need to leave a free end of 15-30 cm to enhance the centrifugal force, which is decisive when removing the trimmer line in automatic and semi-automatic spools. We pass the left end through the working hole of the coil and assemble the head.
How to remove and disassemble a coil
Before starting the cord replacement process, trimmer users need to remove and disassemble the reel. Let’s see how to do it.
The trimmer cutter head consists of several parts: a cover, a spring (not on all models), a bobbin with a cord and a cover.
In trimmers, 2 options for attaching the mowing head are most often used.
How to thread the line into the trimmer spool?
To cut the lawn quickly and effortlessly, the trimmer was invented. When using this technique, sooner or later it is necessary to replace the fishing line, which is the main cutting element. To avoid any problems, you need to know how to properly thread the line into the reel.
First, it is important to choose the right line based on the trimmer model and type of work. The main parameters to be guided by: diameter and section. The first value should be selected for a specific model, and it is indicated in the passport data. The section is selected depending on the type of work, so a round section is suitable for young grass, for coarser plants. square and pentahedral fishing line.
How to thread the line into the trimmer spool?
In order not to break the device, it is necessary to take into account some rules for refueling, which will allow you to get a good result and cope with the work in 15-20 minutes. When figuring out how to tuck the line into the trimmer spool, you need to start by removing the nozzle from the gearbox. To do this, it is necessary to connect the side hole located in the lower figured washer and the recesses on the axle. Insert a screwdriver to prevent the shaft from turning. To unscrew the nozzle, turn it to the right. To remove the coil, disassemble the case. In most models, the cover is secured with latches, which must be sunk into the body, and then squeeze the edges of the cover. Please note that if the line is fed in automatic or semi-automatic mode, then the spring may fly out during disassembly, so the parts must be carefully supported. Since there are different coils, consider the main options.
If the trimmer uses a reel that has a through hole on the inner and outer housing, then thread the line through both holes and assemble the reel. To wind the line, you need to turn the button, which is usually used to release it.
Let’s figure out how to thread the line into a reel working with one cutting element. This option is the simplest. Find a hole inside the spool that allows you to fix the fishing line. Insert its end into it and start winding, moving in the other direction relative to the rotation of the coil itself. Some reels have an arrow indicating the correct direction. The required length of the line directly depends on the size of the reel, usually 2-4 m. A sufficiently large piece of line should be left unlocked so that it protrudes out. Inside the spool, you should find a groove designed to fix the end of the line. If not, then hold the end with your hands. Put on the top of the reel by threading the end of the line through the hole. It remains only to install the coil in its rightful place.
Now let’s figure out how to thread the line into the trimmer spool with two cutting elements. The coil may have one or two antenna grooves, which determines the principle of operation. If there is only one groove, then unwind 2-4 m of fishing line and thread it through the through hole so that it divides the fishing line into two parts of the same length. Guided by the indicated arrows, two parts of the fishing line are wound at once. Leave small ends and pinch them into the grooves or hold them with your hands. Slip on the outer body of the coil where there will be two holes for each end.
In the event that there are two grooves, then the measured piece of fishing line must be folded in half to form a loop, and insert the fold into the groove located between the grooves. Wrap two lines at once, placing them in their grooves. Further assembly is carried out as in a coil with one groove.
Preliminary preparation
First of all, to wind the fishing line, you need to remove the spool (bobbin, spool) from the trimmer. specific actions will depend on the complexity of the configuration and the type of the product itself:
- Small electric trimmers with a working engine and bottom coil usually have side buttons on either side of the bobbin. When pressed at the same time, the upper part of the spool together with the inner content for winding the line is detached, while the lower part remains on the trimmer. It is advisable to disassemble the bobbin on a flat, smooth place so that the spring included in the structure does not jump out and get lost;
- Electric and gasoline trimmers with a curved bar without the possibility of installing a knife, as a rule, have spools with a special wing: in such designs, hold the spool in a stationary position with one hand, and rotate the locking reel on the rod with the wing nut counterclockwise with the other. After disconnecting the nut, the entire bobbin is removed.
- Electric and gasoline trimmers with the ability to install the knife on a straight bar (for example, Stihl trimmers) have a hole under the reel. To keep the rod stationary, a screwdriver or other suitable object is inserted into this hole and, with slow rotation, such a mutual arrangement is achieved when the screwdriver enters the hole and the bobbin is fixed. After that, the coil body is scrolled clockwise (with a left-hand thread) and removed from the trimmer.
Coil with two working antennae
The simplest option and uncomplicated sequence of actions:
- The dimensions of the reel and the length of the original factory winding determine the recommended length of the line for winding. 2. 5 m.
- One end of the line is inserted into the fixing technological hole located inside the spool.
- The fishing line is wound on the drum in the opposite direction of the spool rotation on the trimmer product. as a rule, on the inside of the reel, an arrow indicates in which direction the winding is carried out.
- A small section of the line is left free to lead it out. it is fixed in a specialized groove on the inside of the bobbin, designed to hold the winding when assembling the bobbin into working condition.
- The left end of the line is passed through the hole in the outer part of the reel.
- The bobbin halves are assembled and put on the trimmer bar.
How to wind the line onto the trimmer spool
Unplug the trimmer before changing the line (switch off the engine for lawn mowers). The procedure is as follows:
- On a curved bar trimmer, unscrew the thumbscrew and remove the mowing head.
- On a straight bar trimmer, insert a screwdriver or hex key into the hole under the spool. Lock the key and unscrew the coil.
- Remove the top cover. There are two options: press the latches (if any) or simply unscrew the cover. Be careful not to lose the spring!
- Take out the rest of the line.
- Measure the line to the desired length and fold it in half. The length depends on the size of the coil and is indicated in the instructions. Usually. from 3 to 5-7 meters.
- Hook the middle of the line into the notch and wind the line in the direction of the arrow on the body. Each end of the line fits into its own half of the reel. Try to keep the line flat, without overlaps.
- Leave free ends 15-20 cm long.Pull them out through the holes on the coil body.
- Close the cover and reinstall the coil, not forgetting about the spring.
Automatic winding reel for lawn mowers.
There is a type of reel in which the automatic mechanism winds itself. from the user it is enough only to correctly fill the line. The fishing line is passed through a hole on the inner part of the body, its antennae without winding are passed through the hole on the outer body, the reel is assembled, and when the winding button is rotated, the fishing line inside is wound independently. In such a spool, it is impossible to make the winding wrong: the mechanism itself will determine the correct direction, since it can only rotate in one direction.
How to properly wind the line around the trimmer spool? Overview
In this type of spools, you should determine the number of grooves for winding the line, lying on the inside of the spool:
- One groove. both tendrils are wound together in one groove;
- Two grooves. each tendril is wound on an individual groove.
The difference in line winding in two-groove spools is that initially a 2-5 m long line segment is folded in half (to determine the middle fold), and the fold loop is inserted into a special groove between the grooves. Both antennae of the fishing line are wound each along its own groove, fixing the antennae and assembling the coil is similar to the one discussed above with one groove.
The first execution of this procedure, perhaps, will seem long and rather laborious, but with time and experience this task will be solved much faster and easier.