Lawn mower troubleshooting sputtering. 9 Fixes For When Your Lawn Mower Won’t Start

There are a number of reasons, mechanical and otherwise, why a mower won’t run. The good news is that fixing most all of the issues is easy enough for a DIYer to handle.

By Tony Carrick and Manasa Reddigari | Updated Aug 8, 2022 4:03 PM

We may earn revenue from the products available on this page and participate in affiliate programs.

Lawn care can be tedious, but once the grass starts growing in the spring, mowing becomes a fact of life in most neighborhoods. When you finally muster the strength to tackle that first cut of the season, there are few sounds as disheartening as that of a lawn mower engine that turns over but doesn’t start.

Before you drag the mower in for repairs or invest in costly replacement parts, first make sure that a clogged air filter, soiled spark plug, damaged safety cable, clogged mowing deck, or contaminated gas isn’t to blame. Work through the following steps, and you may be able to get your puttering grass guzzler up and running again in no time.

A lawn mower repair professional can help. Get free, no-commitment repair estimates from pros near you.

Change the lawn mower carburetor filter.

Your lawn mower’s air filter guards the carburetor and engine from debris like grass clippings and dirt. When the air filter becomes clogged or too dirty, it can prevent the engine from starting. To keep this from happening, replace paper filters—or clean or replace foam filters—after every 25 hours of engine use.

The process for removing the filter depends on whether you are operating a riding or walk-behind lawn mower. For a riding mower, turn off the engine and engage the parking brake; for a walk-behind mower, pull the spark plug wire from the plug. Then, lift the filter from its housing.

The only choice for paper filters is replacement. If you’re cleaning a foam filter, wash it in a solution of hot water and detergent to loosen grime. Allow it to dry completely, and then wipe fresh motor oil over the filter, replace it in its housing, and power up the mower—this time to the pleasant whirring of an engine in tip-top condition.

Check the spark plug.

Is your lawn mower still being stubborn? The culprit may be the spark plug, which is responsible for creating the spark that ignites the fuel in the engine. If it’s loosened, disconnected, or coated in water or carbon residue, the spark plug may be the cause of your machine’s malfunction.

Locate the spark plug, often found on the front of the mower, and disconnect the spark plug wire, revealing the plug beneath. Use a socket wrench to unscrew the spark plug and remove it.

Check the electrode and insulator. If you see buildup, spray brake cleaner onto the plug, and let it soak for several minutes before wiping it with a clean cloth. Reinstall the spark plug, first by hand, and then with a socket wrench for a final tightening. If the problem persists, consider changing the spark plug.

Clear the mower deck of debris.

The mower’s deck prevents grass clippings from showering into the air like confetti, but it also creates a place for them to collect. Grass clippings can clog the mower deck, especially while mowing a wet lawn, preventing the blade from turning.

If the starter rope seems stuck or is difficult to pull, then it’s probably due to a clogged deck. With the mower safely turned off, tip it over onto its side and examine the underbelly. If there are large clumps of cut grass caught between the blade and deck, use a trowel to scrape these clippings free. When the deck is clean again, set the mower back on its feet and start it up.

Clear the vent in the lawn mower fuel cap.

The mower started just fine, you’ve made the first few passes, then all of a sudden the mower quits. You pull the cord a few times, but the engine just sputters and dies. What’s happening? It could have something to do with the fuel cap. Most mowers have a vented fuel cap. This vent is intended to release pressure, allowing fuel to flow from the tank to the carburetor. Without the vent, the gas fumes inside the tank begin to build up, creating a vacuum that eventually becomes so strong that it stops the flow of fuel.

To find out if this is the problem, remove the gas cap to break the vacuum, then reattach it. The mower should start right up. But if the lawn mower won’t stay running and cuts off again after 10 minutes or so, you’ll need to get a new gas cap.

Clean and refill the lawn mower fuel tank.

An obvious—and often overlooked—reason your mower may not be starting is that the tank is empty or contains gas that is either old or contaminated with excess moisture and dirt. If your gas is more than a month old, use an oil siphon pump to drain it from the tank.

(It’s important to be careful as spilled oil can cause smoking, but there are other reasons this might happen. Read more about what to do when your lawn mower is smoking.)

Add fuel stabilizer to the tank.

Fill the tank with fresh fuel and a fuel stabilizer to extend the life of the gas and prevent future buildup. A clogged fuel filter is another possible reason for a lawn mower not to start. When the filter is clogged, the engine can’t access the gas that makes the system go. If your mower has a fuel filter (not all do), check to make sure it’s functioning properly.

First, remove the fuel line at the carburetor. Gas should flow out. If it doesn’t, confirm that the fuel shutoff valve isn’t accidentally closed. Then remove the fuel line that’s ahead of the fuel filter inlet. If gas runs out freely, there’s a problem with the fuel filter. Consult your owner’s manual for instructions on replacing the filter and reassembling the mower.

Inspect the safety release mechanism cable.

Your lawn mower’s reluctance to start may have nothing to do with the engine at all but rather with one of the mower’s safety features: the dead man’s control. This colorfully named safety bar must be held in place by the operator for the engine to start or run. When the bar is released, the engine stops. While this mechanism cuts down on the likelihood of horrific lawn mower accidents, it also can be the reason the mower won’t start.

The safety bar of a dead man’s control is attached to a metal cable that connects to the engine’s ignition coil, which is responsible for sending current to the spark plug. If your lawn mower’s engine won’t start, check to see if that cable is damaged or broken. If it is, you’ll need to replace it before the mower will start.

Fortunately, replacing a broken control cable is an easy job. You may, however, have to wait a few days to get the part. Jot down the serial number of your lawn mower, then head to the manufacturer’s website to order a new cable.

Check to see if the flywheel brake is fully engaged.

The flywheel helps to make the engine work smoothly through inertia. When it isn’t working properly, it will prevent the mower’s engine from working.

If it is fully engaged, it can make a mower’s pull cord hard to pull. Check the brake pad to see if it makes full contact with the flywheel and that there isn’t anything jamming the blade so the control lever can move freely.

If the flywheel brake’s key sheared, the mower may have run over something that got tangled in the blade. It is possible to replace a flywheel key, but it does require taking apart the mower.

Look out for signs that the mower needs professional repairs.

While repairing lawn mowers can be a DIY job, there are times when it can be best to ask a professional to help repair a lawn mower. If you’ve done all of the proper mower maintenance that is recommended by the manufacturer, and gone through all of the possible ways to fix the mower from the steps above, then it may be best to call a pro. Here are a few signs that indicate when a pro’s help is a good idea.

• You see black smoke. The engine will benefit from a technician’s evaluation, as it could be cracked or something else might be worn out.
• Excessive oil or gas usage. If you’ve changed the spark plugs, and done all of the other maintenance tasks, and the mower is consuming more than its usual amount of oil or gas, consult a professional for an evaluation.
• The lawn mower is making a knocking sound. When a lawn mower starts making a knocking sound, something could be bent or out of alignment. It may be tough to figure this out on your own, so a pro could help.
• A vibrating or shaking lawn mower can be a sign of a problem beyond a DIY fix. Usually something is loose or not aligning properly.

Learn the reasons why a lawn mower won’t start after winter or during peak season, and how to fix those problems.

Family Handyman

Introduction

Most of the time when a lawn mower won’t start the cause is a problem with the gas or the lawn mower carburetor.

What to Do if Your Lawn Mower Won’t Start

Whatever kind of lawn mower you’ve got, the last thing you want once winter finally lifts and spring has sprung is a lawn mower that won’t start.

If you’ve taken the proper steps to winterize your lawn mower, you’re far less likely to be dealing with such issues. It’s also why you should tune up your lawn mower at the start of every season. However, it’s not out of the ordinary to find your gas-powered lawn mower not starting from time to time, so it’s important to know why your lawn mower isn’t starting and how to fix it.

Project step-by-step (6)

Check the Gas Tank

Let’s start with the obvious. Before you have a heart attack pulling on the rip cord, you’ll want to check the fuel. Like any gasoline-powered engine, lawn mowers run out from time to time. Maybe you forgot it was running on fumes when you finished mowing last time. It sounds simple, but we’ve all overlooked the gas tank from time to time.

Even if there is gas in the mower, if the fuel’s been in there more than a month, that could be the problem. Gas sitting around too long in the tank can get contaminated with dirt and extra moisture.

So if your gasoline has been in the mower for more than month, drain the gas properly, dispose of it correctly, and fill up the mower with new gas. It may take quite a few pulls to suck the new gas into the lawn mower carburetor, so be prepared to clean and dry the plug a few more times.

Add fuel stabilizer when you fill up the tank to help protect the gasoline in there from dirt and moisture.

Family Handyman

Check the Spark Plug

Start by making sure the lawn mower spark plug cable is connected to the plug itself. It’s quite possible that it got pulled off there over the winter while the mower was being stored in the garage.

If that’s not the issue, the next step is to remove the spark plug to see if it’s wet. There’s no way the engine will start if it is. So clean the plug with carburetor cleaner and let it dry. Cleaning it with compressed air isn’t enough; you need a solvent to remove oil residue. If it’s really grimy and dirty, it might be best to change the spark plug.

Fertnig/Getty Images

Check for Debris in the Mower Deck

Grass clippings can get clogged in the mower deck, which can prevent the blade from turning. This is a common problem if you’ve cut wet grass or let the lawn get especially long and bushy between cuttings. If the cord is hard to pull, that’s a good sign that there’s debris clogging up your mower’s deck.

This is a pretty easy problem to solve. With the mower off, flip it on its side or upside down and scrape out the gummed up grass clippings. Once that’s done, you can flip it back over and start it up again.

JJ Gouin/Getty Images

Check the Air Filter

The lawn mower’s carburetor regulates the mix of gasoline and air going into the engine where it’s burned to create power. Before air goes into the carburetor it passes through the air filter which prevents dirt and debris from getting into it.

If the air filer is clogged or dirty, it throws the ratio out of whack. Sometimes that results in your lawn mower smoking, and sometimes it prevents it from starting entirely. So take a look at the air filter to see if it’s dirty. If so, you can clean it or just change it outright.

Robert Maxwell for Family Handyman

Check the Carburetor

Another common reason for a lawn mower that won’t start is a clogged or dirty carburetor. It can also cause your mower to run rough or spew black smoke when you’re trying to cut the grass. If that’s the case, you may need to clean the carburetor.

To get to the carburetor, you’ll have to remove the air filter. Once that’s out of the way, you can remove the carburetor in order to clean it.

Once it’s out, check for corrosion. If you see chalky/powdery white corrosion like this, it’s probably better just to replace it. To clean it, take it apart and spray carburetor cleaner on the parts and inside the housing. After that, put the carburetor back together and reinstall it in the mower.

Check the Fuel Filter

Like the air filter, the fuel filter prevents dirt and debris from getting into the combustion chamber of your lawn mower’s engine, taking that stuff out before the gas gets mixed with air in the carburetor. Problems with the fuel filter might also result in the engine sputtering or rough idling, even before it gets to the point of preventing the mower from starting.

To start, tap the side of the carburetor to help the flow of gas. If that doesn’t work, you might have a clogged filter.

Not all lawn mowers have a fuel filter, but for the ones that do, it’s usually located in the fuel line or the fuel tank. To find out where the fuel filter is at, check your lawn mower’s owners manual, which will also tell you what type of filter it is.

If the filter is in the fuel tank, you’ll need to drain the gas from the mower into a drain pan, assuming you can’t run the engine until it’s out of gas. If the filter is in the fuel line, clamp off the fuel line before removing the filter. Once you have the filter off, you can check to see if it’s dirty and clogged by holding it up the light. If it is, install a new one. Make sure it works with this lawn mower maintenance checklist.

Lawn Mower Engine Surging – Check this easy fix first!

Lawnmower engine surging is a right pain in the Jacksie; it’s an engine that runs erratically and revs up and down by itself uncontrollably. In some cases, it may only happen under certain conditions, for example, only after the mower gets hot or only when the fuel level gets low.

So what causes the lawnmower engines to surge? The most common reason for a surging lawn mower engine is a blockage in the fuel supply, but there are other possibilities:

Often you’ll find playing around with the throttle helps or applying some choke. You are not on your own; this is a regular complaint. In this guide, we will cover the diagnosis, likely causes, and solutions.

Try the easy fix first – replacing/cleaning gapping the spark plug before attempting carburetor work. If your mower engine is a Honda or Kohler, the fix is simple. Honda and Kohler’s surging is commonly caused by a blocked idle jet see “Gas starvation” towards the end of the page.

If you need more help, check out the “How to fix a surging mower video.”

If your surging mower is a Honda, check out the “Honda mower surging video.”

For many mowers, the fix is to replace the carburetor, and as carburetors are inexpensive, it just makes sense to swap it out and save a ton of messing around. You can check out the quality carburetors available and conveniently delivered to your door by Amazon.com.

Need more info on the fuel system, carburetor components, and how they work, you can check them out here.

Briggs Stratton Surging

Surging BS Classic 450, 500, or 550Some engine types are famous for surging; the Briggs Stratton 450, 500, and 550 series engines are fitted with a metal fuel tank and priming bulb-style carburetor. If you have one of these types of engines and it’s surging – You’re in the right place.

If you don’t have this type of carburetor, skip this section and jump to “Surging Test” below. These engines are fitted with a metal fuel tank and carburetor combination. The gasket sandwiched between the tank, and carburetor distorts over time, allowing a vacuum leak.

The vacuum leak causes the surging; replacing the gaskets and cleaning the carburetor/tank will leave it like new, I promise. In this tutorial, we’ll remove the tank/carburetor unit, clean it and replace the gaskets. Just some basic tools are needed, but get yourself a can of carburetor cleaner; it makes the job a lot easier.

In the workshop, I use WD40 carb cleaner, and you can check out all the tools and parts I use here on the “Small engine repair tools” page.

Tools You’ll Need

Here’s a short list of tools you’ll find useful to complete the task of fixing your surging mower. These tools aren’t essential, but they do make the whole job a ton easier; you’ll need:

Fuel treatment – Every small engine owner should use gas treatment. Most people don’t know gas goes off, and gas left in small engines can cause real problems, as you already know.

Using a gas stabilizer will keep the gas in your mower and your gas can fresh for up to two years.

Carburetor gasket – If you’re fixing the BS Classic engine, then you’ll need this gasket set.

Complete carburetor – As an alternative to replacing your BS Classic carburetor gasket, replace the complete carburetor instead; it includes the replacement gasket.

Manifold – This will only be needed if you have confirmed it has failed. Note there are a few different types of manifold pipe, so be sure to check before ordering.

You can check out all these tools on this page “Carburetor Surging Repair Tools.”

This carburetor style is fitted to a few engines and is prone to gasket failure. The job of replacing is simple and will solve the surge. The process is as follows:

Remove the spark plug wire – prevents the mower from starting.

Remove – Remove and clean the air filter and filter housing – Clean it using soapy water, and when dry, smear some engine oil over the surface of the foam. This helps trap dirt.

Remove tank bolts – They hold the fuel tank to the engine.

With fuel tank bolts removed – pull the tank unit straight out gently and remove the governor control link.

Remove the black rubber elbow crankcase breather pipe. Remove the manifold seal and keeper ring. Sometimes they will come loose and get stuck on the manifold pipe.

Remove – Remove carb screws from the carburetor and set aside.

Using a can of carburetor cleaner – clean all the ports on the surface of the fuel tank.

Empty the tank and rinse it out with fresh gas.

Pull the Siphon from the carburetor; they can be stubborn. Remove both gaskets and use carburetor cleaner to clean the siphon metal filter and all ports of the carburetor. Check the primer bulb for damage; mice like to eat them.

Spray – Spray the carburetor with carb cleaner.

Remove – Remove old gaskets and discard them.

Careful of this spring; it lives under the gaskets, and it can drop off and be tricky to find, as I know only too well.

The gasket is a two-part kit; the rubber-type gasket faces the tank. (carb fitted here for demo only)

The Siphon pushes back into the carb with a click. If you don’t hear the click, it’s not right – try again.

Refit the carburetor to the tank. Don’t over-tighten the screws, as this will distort the gasket. Fit manifold seal and keeper. Smear a small amount of oil on the seal; it helps it seat.

Clean the intake manifold. The grey tube in this shot is manifold. Inspect it for any signs of damage; they are prone to cracking. This will also cause a surge.

To fully inspect the pipe, you need to remove the pull assembly.

I would only do this if there was obvious damage to the manifold or if I had replaced the carburetor gasket and the engine was still surging.

This manifold is cracked and will cause a surge.

Before refitting the tank, fit the keeper ring and O-ring seal. Lube the seal before refitting the gas tank.

Offer the carb/tank unit up to the manifold and attach the governor link and spring. Now push the unit firmly onto the manifold. Fit both bolts.

Refit the air filter and spark plug wire. Use only fresh gas; make sure your gas can is clean. Gas older than three months is stale.

If, after fitting the gaskets, you still have a surge – Replace the Manifold.

Surging Test

As you know, gas starvation causes an inconsistent flow of fuel which in turn causes erratic running. And you also know a vacuum leak will cause erratic running, but it is a much less common cause; however, some carburetors are prone to vacuum leaks.

As engine manufacturers strive to make their engines more efficient, they have also made the carburetors more likely to clog; this has become a common issue.

To quickly diagnose which problem you have, a clogged carb or vacuum leak, follow this simple test.

You will need a helper to hold the bail lever or improvise with duct tape. CAUTION careful where you place your fingers and toes; the engine will be running, so the blade will be spinning.

Your mower will have a Manual choke, Auto choke, or a Primer bulb. Identify which type your mower has; the test is slightly different for each.

If you have a manual choke – apply half choke with the engine running.

If the engine now runs without surging – Gas starvation is the likely fault. If it runs just the same – A vacuum leak is a more likely fault.

If you have an Auto choke – Remove the air filter cover and filter – place a clean rag over the intake while the engine is running.

If the engine now runs without surging – Gas starvation is the likely fault.

If the engine runs just the same – A vacuum leak is the more likely fault.

If you have a primer bulb – you can still do the test – while the engine’s running (need a helper); give it some extra gas by pressing the bulb.

If the engine now runs without surging – Gas starvation is the likely fault.

If it runs just the same – A vacuum leak is a more likely fault.

Gas Starvation

If the test revealed gas starvation, it also showed that your problem is likely a dirty fuel jet in the carburetor, or the gas may be stale or contaminated by water.

Cleaning the main jet usually does the job.

Idle Jet Surging – Honda and Kohler use a relatively easy-to-access idle jet that clogs up and causes surging. The Kohler is easier to access than the Honda.

The Kohler is easier to access than the Honda.

Briggs has fitted a plastic carburetor to a range of engines which also clog up and cause surging.

All of these carburetors can be repaired by cleaning, which I’ve covered previously in videos (links below). Videos cover step-by-step removal, cleaning, refitting, and adjusting your carb.

Fixing this is not difficult. Sometimes you can get lucky by just draining and cleaning the gas bowl, which only takes a few minutes.

I have written a complete guide to Carburetor cleaning with pictures; it includes the gas bowl clean-out, which, as said, is worth trying first.

If cleaning doesn’t work out for you, go ahead and swap out the carburetor for a new one. Check out “New lawn mower carburetors page,” here, I’ve listed good quality replacement carburetors for all the most popular engines.

Carburetors aren’t expensive; messing around with them doesn’t make sense.

You might find this page helpful too – “Carburetor repair tools” I’ve listed some really useful tools that make the job easy. Some of these tools I’ll bet you already have some.

But do try cleaning the gas bowl before removing the carburetor.

Finding a Vacuum Leak

Air that enters the combustion chamber without passing through the carburetor is un-metered. This means the fuel-to-air ratio is unbalanced and, in turn, causes erratic engine performance.

When air sneaks in like this, it causes the engine to run lean (lacks gas). A lean engine runs hot, which isn’t good for an engine, especially an air-cooled one.

Vacuum leaks usually occur because of damaged gaskets. Gaskets are sealing materials fitted between the mating surfaces of engine components. Their function is to create an airtight seal.

They are commonly made from paper, felt, cork, Teflon, neoprene, metal, and rubber. The material type is dependent upon where the gasket is to be used.

Gaskets wear out and break down, and that causes surging.

Extreme Caution – You need to be careful, the engine will need to be running, and so the blade will be spinning when running this test.

A vacuum leak check is performed with the engine running and a can of carburetor cleaner; WD40 works, too, (is there anything WD can’t do?)

Spray the cleaner around all carburetor gaskets anywhere the carburetor meets the engine. The trick is to hear an instant change in engine note; that’s the sign of a vacuum leak.

This can be challenging; you must train your ear to notice the instant change in engine note (and not the surging).

Just do a small section at a time; this will allow you to pinpoint the failure area. Jumping the gun and replacing gaskets without finding the actual leak may work out for you or leave you with the same problem after the rebuild.

You’re right in thinking carburetor gaskets usually cause the problem, but other components, such as manifold pipes, can crack or become loose, causing surging.

Fixing A Vacuum Leak

If a leak is detected, replace all carburetor gaskets, and as you have the carburetor removed, go ahead and clean it. Replacement gaskets are available online; you will require the make and model numbers from the engine.

All manufacturers will have a model number printed on a sticker placed on the body or on the engine. Have a poke around; you’ll find it. Most engine manufacturers will stamp the model numbers in an accessible area. Briggs Stratton stamp their numbers on the metal engine cover.

A new carburetor comes with new inlet gaskets; I like to fit original parts where I can; they fit and are guaranteed.

If, after replacing the carburetor gaskets, the engine still surges, you’ll need to go a little further and replace the manifold intake and gasket.

It’s not a big job, and they don’t give a lot of trouble, but they do crack as they get older. I wrote a step-by-step guide showing you everything you need to know – “Briggs Manifold Replacing.”

Related Question

Honda lawn mower surging fix? To fix a surging Honda lawn mower engine, clean the carburetor, gas tank, and fuel filter. Use fresh regular gas or e10. What causes a lawnmower to run slowly? The most likely cause is a throttle linkage bent out of shape by bumping into the shrubbery or a throttle spring has detached itself.

Hey, I’m John, and I’m a Red Seal Qualified Service Technician with over twenty-five years experience.

I’ve worked on all types of mechanical equipment, from cars to grass machinery, and this site is where I share fluff-free hacks, tips, and insider know-how.

And the best part. it’s free!

There are few things more frustrating than when you’re trying to mow the grass and the lawn mower keeps dying. Luckily, there are a few causes that you can troubleshoot without having to buy a brand-new mower.

By Melissa Graham | Published May 31, 2023 1:30 PM

We may earn revenue from the products available on this page and participate in affiliate programs.

Q: I’ve tried to mow my lawn multiple times this week, but the lawn mower keeps dying. What could be causing it to stop running? Do I need to call a professional or buy a new mower, or is this something I can fix myself?

A: Your mowing shoes are on, you’ve put on sunscreen, and you’re ready to tackle your overgrown yard. But instead of hearing the smooth sound of the engine running, the mower sputters to a stop. When a lawn mower keeps dying, it can prevent a homeowner from doing the necessary work to maintain the home’s curb appeal. The good news is that lawn mower repair can often be a DIY project. From how to clean a lawn mower carburetor to replacing a lawn mower’s battery, the steps below can help solve almost any lawn mower problems.

For those who lack DIY experience and would rather leave the repairs to a professional, one of the best lawn mower repair services will know why a lawn mower won’t start and how to solve the problem so it springs back to life.

A dirty carburetor or clogged carburetor bowl could cause a lawn mower to stop running.

If a lawn mower won’t stay running, a dirty or clogged carburetor could be the culprit. A carburetor mixes the air and fuel in the mower to create internal combustion. If the bowl gets clogged or fuel residue affects the inlet or outlet ports, the motor could stop running. Clogged carburetors also tend to result in the production of black smoke or sneezing and popping noises.

To resolve this problem, it’s possible to disconnect the fuel lines and apply a carburetor cleaner to get rid of any leftover slime from old fuel.

Old gasoline needs to be changed for the lawn mower to run properly.

When a lawn mower sits dormant for months without use, old fuel can evaporate and leave a sticky residue that prevents the mower from running properly. Old gasoline will also have a sour smell. If the lawn mower starts and then dies frequently, it may be necessary to drain the old fuel out of the tank and clean off carburetor ports before adding new fuel. This is especially true for mowers in cold climates, when conditions can lead to condensation inside the fuel tank.

Dirty or defective spark plugs can cause a lawn mower to stop working.

A spark plug ignites the fuel in the lawn mower’s engine, which is why a dirty or defective spark plug could be the reason a mower keeps dying. If the engine is turning over quickly but not starting, the lawn mower sounds weak, or it seems harder to pull the rewind on the mower, the spark plugs may be dirty or defective.

It’s first necessary to find and inspect the spark plug, which is typically positioned on the front of the mower. Here, it’s possible to see if the electrode and insulator have accumulated any buildup or become disconnected. If the plug is dirty, it needs to be disconnected and cleaned with a wire brush and specific spark plug cleaner. (Even if the spark plug doesn’t show significant buildup, it’s still wise to clean it.) The spark plug will then need to be reconnected to see if the mower starts and stays running. If the mower continues to die, it may need a new spark plug altogether.

Too much oil in the reservoir can cause lawn mower problems.

Even the best lawn mowers can experience issues if there’s too much oil in the reservoir. Excess oil in a lawn mower can force the engine to produce more heat, which could lead to the machine overheating. If the lawn mower is blowing white smoke after it’s started, that’s a good indication that there’s too much oil in the reservoir, and a lawn mower that stops running when it’s hot outside could be overheating from an overfull reservoir. Too much oil can also affect the crankcase by causing the oil sump to overflow and causing the crankcase to malfunction.

This issue can be resolved by unscrewing the oil tube and tilting the lawn mower on its side to release the excess oil into a container. At this point, it’s also best to change the oil filter after removing the oil to make sure it’s free from clogs. For those wary of troubleshooting a lawn mower, a lawn mower repair service can check out the machine and help with anything from riding lawn mower repairs to tips on regular maintenance.

A clogged fuel cap vent can make a lawn mower die.

A majority of mowers have a vented fuel cap that helps release pressure in the machine and allows fuel to flow from the gas tank to the carburetor. If the fuel cap vent becomes blocked or clogged, it could lead to excess gas fumes inside the mower, which stops the flow of fuel and could be why the lawn mower keeps dying. A needle or pin can be used to poke out any blockages from the breather hole. If the cap has any damage, it’s likely easier to buy a new cap altogether.

A professional repair service can solve any type of lawn mower problem.

When all of the options have been exhausted and you’re tired of tinkering with the mower, it may be time to throw in the towel and call a professional. The best lawn mower repair professionals have the skills and experience to identify problems right away and can often fix them on the spot so homeowners don’t have to keep running to the hardware store. The mower may also be experiencing an issue that only a professional can address, which is especially true if there is black smoke coming from the mower or if the mower starts vibrating or shaking once started.

Lawn mower maintenance can keep the mower running smoothly.

As with any appliance or machine, regular maintenance ensures a mower is in mint condition and won’t experience the many problems that can come with neglect. Regularly cleaning debris from air filters and mowing decks, removing any old gas from the tank, and replacing the battery when needed are all good practices to keep in place when it comes to lawn mower maintenance. The more a mower is taken care of, the less likely a homeowner is to experience issues such as a stalling lawn mower or lawn mower chugging.

Why is My Lawn Mower Smoking?

Four candles/Shutterstock

Leaking oil from the exhaust is the usual cause of blue, white or black smoke from a lawn mower. Learn to assess and fix a sputtering, smoking lawn mower.

Gas-powered lawn mowers can be full of surprises. Perhaps the most startling one happens when you pull the mower cord and the engine sputters into action, only to be followed by clouds of smoke from the motor and under the mower deck. What’s going on and what should you do about it?

Why is My Lawn Mower Smoking?

There are several reasons your lawn mower could be bellowing out smoke. While it looks kind of intimidating, like something bad is about to happen, in most cases, it’s nothing to be worried about, and it’s not usually hard to fix.

Oil spilled onto the engine: If you changed your lawn mower’s oil recently or added more to the oil reservoir, some may have spilled out onto the engine. Mowing on a steep slope in the yard, or turning it over to adjust the blade, could also cause some oil onto the engine. When that happens, the oil will burn off, causing blue or white smoke. It’s best just to let it burn off, so when you start up again, the oil will be gone.

Overfilled oil reservoir: Too much oil in the reservoir can also cause a lawn mower to smoke. The lubrication systems in most mowers are not well sealed, and usually there’s an overflow oil reservoir with a relief outlet where excess oil can leak. Check the oil level in your mower, and if there’s too much in there, consult the manual for how to drain some out until it’s back at the proper level.

Mower burning too much gasoline: The carburetor regulates the ratio of gasoline and air in a lawn mower engine. If the carburetor isn’t getting enough air, that means the mix is heavy on gasoline, which can cause black smoke from the exhaust. Often times that’s caused by a dirty air filter, which is preventing enough air from getting to the carburetor.

Different Types and Colors of Smoke

If the smoke is black, there may be an engine problem behind the smoke. In such cases, your first step after the mower cools down should be to check the air filter. If it’s clogged, the combustion chamber may not be getting enough oxygen, resulting in a too-rich fuel mixture that will cause the engine to run poorly and even spew smoke. The solution is to change the air filter, a relatively easy task.

Blue and white smoke is the result of oil on the engine. If there’s too much oil in your oil reservoir, you may want to drain some of it out. If it’s just some oil spilled onto the engine, all you have to do is let it burn off.

When to Take a Smoking Lawn Mower to the Repair Shop

If your smoke problems persist, chances are the oil seals in the engine lubrication system or around the pistons are the issue, or you may even have a cracked crankcase. These are repair jobs for a small engine pro, unless you’ve got experience working on engines.

There is also a chance the smoke is simply the result of a carburetor that needs cleaning or adjusting. If you’re up for it, most owners’ manuals include instructions on how to adjust and clean the carburetor.

Remember, it’s important to tune up your lawn mower at the start of the season, which will help make sure it’s running properly and prevent potential problems like a Cloud of smoke following you around the yard.

Troubleshooting and Fixing the Mower

Mark Johanson is an experienced home and garden writer/editor/publisher. He has written several books and hundreds of magazine articles. He has edited and directed more than 400 DIY and gardening books, including the BLACKDECKER® Home Improvement Library series and two of the best-selling gardening books in North America. He is an experienced DIYer and enthusiastic gardener.