Lubricant for the STIHL mower gearbox. Repair trimmer for STIHL grass with STIHL FS 38

Lubricant for a trimmer gearbox for STIHL Evdiral grass.Ru

Reducer Motokosa Purchase of any equipment in its kind a lottery, but much also depends on the gardener. In caring hands and Chinese samples serve for a long time and do not let their owners at the wrong time. And if you forget to lubricate the motorcosa gearbox in time, do not clean filters, use cheap low.quality gasoline, then garden equipment from the most eminent brands will be a headache.

Lubrication of the gearbox Motokos is one of the most important elements of maintenance of a gasoline trimmer for grass, which the user should be carried out directly.

Time and procedure for the prevention of the gearbox

I recommend that the prevention of a new gasoline trimmer for grass immediately after purchase, with the addition of lubrication in the gearbox. For all the high cost of garden technology, some manufacturers save and lay lubrication only at a minimum, for the duration of the run.in.

How often to lubricate the gearbox motokos

Often, a preventive inspection of the transmission with the addition of liquid consistent lubrication is carried out once a year at the beginning or end of the season. If the gasoline trimmer for grass is used not in professional volumes, this is enough.

With large volumes of the mowing, lubricate the motorcosa gearbox every 20-50 hours of work. If the conditions of the operating mode of garden equipment are difficult, for example, a large field is pumped out at a time, and at the same time the lawn mower does not have time to cool down, or cheap lubricants are used, then the lubricant must be checked and added every 20 hours of work.

Indirect evidence that it is necessary to lubricate the gearbox to overheating or increased noise of the node.

I also recommend a complete replacement of lubrication, with disassembly and flushing of the node, when buying a used gasoline trimmer for grass.

Lubrication for gearbox of gasoline trimmer for grass

Assortment of lubricants for garden technology

According to the instructions for lubricating the conical gearbox, a special transmission liquid consistent grease should be used. As a rule, manufacturers of garden equipment produce and recommend the chemistry of their brand as the most adapted to their devices.

At the same time, to reduce the cost of the operation of garden equipment and increase the attractiveness of a brand of auto chemistry, grease for garden equipment usually produces multifunctional. It is intended not only for lubricating gearboxes of gasoline trimmers, but also for processing hoses, transmissions and gearboxes of any garden equipment and mechanical devices operating under high loads.

Such lubricant for the gearbox is sold in the tubes convenient for use and subsequent storage.

Even if a specialized lubricant for the gearbox was almost completely developed during operation, the additives still create an effective lubricating protective film on the surface of the gears.

It should be noted that many owners of the motorcycle in the vast CIS for lubrication of the gearbox use ordinary litol-24 or lubricant for Circus on a lithium basis. It is convenient to refuel the gearbox using a 5-cc medical syringe.

A undoubted plus of the use of lithola and lithium.based lubricant for refueling the transmission of motorcycles is a reduction in operation. But there are nuances because of which spears are breaking on the forums of the Internet gardeners. My thoughts on the topic, what can be lubricated with lubric.based lubricants, and what is not read in the article “Litol as lubrication of the motorcosa gearbox”.

How to lubricate the motorcosa gearbox, gasoline trimmer for grass

Side Bolt on 17 on the gearbox of a gasoline trimmer for grass

In order to avoid random launch, all preventive work on a motorcycle is necessarily carried out with a removed electric cap / plug from a candle. Do not turn the trimmer for the grass to avoid gas leakage.

We unscrew the side screw on the motorcosa gearbox. Depending on the company.manufacturer of a garden tool, instead of a screw for a hexagon, there may be a turnkey bolt, more often at 17. The thread is ordinary, unscrew counterclockwise. Do not lose the sealing puck.

If the lubricant is not visible on the internal end part of the screw, then it is necessary to add 3. 4 grams. Scroll through the gear with your hand, changing the direction of rotation so that the lubricant is distributed through the gears.

Then set the screw in place, tightly tightening it.

Why choose a FS 55 lawn mower

If you still do not know which model of the described equipment to choose, then you should read reviews about the gas tanks “Stihl FS 55″. Having familiarized themselves with them, you can understand that consumers identify many reasons that made them bow towards the described model. So, for example, instead of a strap, the manufacturer supplied the device with a belt. This allows you to distribute the load from the device throughout the back. Otherwise, the weight would be focused on only one shoulder. With this option, even after a very long operation, there is no back pain.

Buyers like a bicycle handle that increases the convenience of management. When working, the hands will be widely placed, so it is easier to control the aggregate. He is very maneuverable. Buyers like that the handle and belt can be adjusted for the needs of the operator.

The tool can be easily configured for comfortable use. Control elements are on one handle. You need to stretch anywhere, everything is located under the palm. The Stihl FS 55 lawn mower, according to consumers, is also convenient for the fact that it has a couple of protective covers, one of which is installed for a knife, while the other is for fishing line. The casing for the latter has a narrowing of the bar.

A trimmer for grass has a head that is clearly visible and allows you to process narrow places. The departure of stones from under the knife will be excluded thanks to a special casing. This allows you to protect the operator. With the help of an existing primer, you can pump up fuel into a carburetor. Even after a long downtime, as consumer reviews testify, the lawn mower is quite simple. The start of the engine is light due to a special light starting system. As the home craftsmen emphasize for a long stretch of the cord, now you will not have to spend strength, because for this it will be necessary to make 2 jerks.

Stihl fs 120 lawn mower. Gear lubrication. Fishing line refueling. Installation of a knife.

Service of the Stihl FS 120 lawn mower. Reducer lubrication, fishing line without taking off the coil and installation of a knife.

I welcome you dear mowers and happy owners of the lawn mower of this and not only model. There is such a saying-man loves affection and technique lubricant. Timely care and maintenance extends the work of any equipment. Tax friends, grab smart replicas, go to business)).

The first where to start the lubrication of the gearbox is a specific container did not tell me.how often it is necessary to do this, it is understandable. Using mowers for everyone is different.

I have a hot climate that I would understand what the speech is about which was already below the cold by the evening of 38 s, so I do not lazy and look into the gearbox every 20-30 mowed hundredths.

Here you can make a uniform or an asterisk, I use the full-time, it is just in common keys, while the mowel is new and the slots are intact)).

As they did not say in the store, the lubricant should be visible and not the bare gears.

While with this everything is fine, I am lubricating.

Here friends will make a small stop. Although I am a self-made one who is interested in working, breaking and doing and even have some kind of technical education, but there are places where it is better not to climb and not to be clever, well, if you are certainly not an engineer who knows more than stoomers of these mowers. Guys do not need to reinvent the bicycle, he is already riding. I saw more than one video where these grief masters advise to shove and clog there a lubricant that is not at all for these purposes-it woven from the heat after a couple of hours of work.

Here has already been done before us, all for a person.

We wind up a tube to the gearbox-drove a little, the excess will go where you need, do not worry.

We twist the tube-and switch the screw-all is ready.

Now let’s move on to winding the fishing line on the coil.

On this model, she pleased with her simplicity and convenience, unlike older models. While the braid has not passed much, 50-60. Everything works like a clock, but the capacity of the coil is up to 8 meters, not to rejoice not to please the hard worker of this machine).

I use mainly a fishing line for a 2.thick trimmer.7 mm, this can be smeared up to 6 meters, on average I do not overload-dramatize. 5 meters.

I was pleased that here it can be done without taking off the coil from the mowing, here is a smart head, which came up with it, who mows at a time more than at least 10 hundred-pages of what about it.

Put the mitch with a reel up and make these marks and slot.

Click on a black slope and insert a fishing line for a trimmer, remove it to the middle and begin to wind it up. For this, there are arrows and cavities, you need to think nothing.

Here, check the seller with how and with what details your knife is placed. I will show on the example of what was in the kit-two-sided (more in the video).

Put the knife-fix the site so that it does not rotate.

Here in principle, all friends, today, perhaps everything. Feel free to ask the supplier important information for you, well, the safety saba itself, so yet, nickname has not canceled it.

Watch the video and more detailed. With you, as always, romance is a rugged homemade.

What lubricant should be used for a trimmer gearbox for grass?

In the process of work, the mechanical part of the trimmer for grass is loaded with contact efforts on the teeth, resistance reactions from adhering grass (sometimes with dirt), dynamic, shock loads due to a constantly changing torque. The lubricant for the gearbox of the trimmer for the grass should fully consider these features, so the selection of the brand should be strictly individual.

The following factors are taken into account:

• Manufacturer’s brand. Repair of a trimmer for the grass Champion T 336 with your own hands of the lawn mower how to lubricate the shaft pcs video. Example. Each trademark is not unreasonably focused on lubricants of its own manufacture (you can talk about cheap Chinese products later). This applies to manufacturers such as Husqvarna, Stihl, Huter, Makita, etc. The exception is trimmers for domestic grass: for example, the caliber in the user’s instructions does not indicate a lubrication brand at all.
• Break of lubrication. As you know, all lubricants are divided into three groups. high.speed (colloidal systems containing various additives), plastic compounds of universal use and hard lubricants softening during operation.
• Good adhesion to the surface of the parts of the gearbox, as a result of which the lubricant is not squeezed into the gaps or outside the node.
• The intensity of lubrication consumption by the gearbox. Here you have to focus on their own experience and recommendations of specialists, since some manufacturers of trimmers, hoping for their own service centers, do not give clear recommendations at all regarding the period of the reducer between two lubricants.

How to lubricate the gearbox of a trimmer for grass?

In the upper part of the case, where the gear unit is installed, there is a technological hole that, when operating the trimmer for the grass, is drowned out with a screw. This screw is twisted, and 1.5 2 ml of grease is introduced into the hole using a nose available on a tube. If the lubricant was purchased in another packaging, then a regular disposable medical syringe is suitable for this operation.

After that, the screw is installed in its former place. This procedure, regardless of the user’s recommendations, should be performed every 10 15 hours of operation of a trimmer for grass in working mode. Other reasons for updating or replacing the reducer lubrication are the independent performing of small regulatory work (for example, cleaning and washing the gear of the gearbox before the start of the summer season), repair of the node, preserving the trimmer for grass for the winter period, etc. D.

If the reducer node is disassembled, it is recommended to completely remove the remaining lubricants from the surface of the parts, even if it does not have traces of oxidation and pollution. And only then apply a new grease. After applying the lubricant, it is recommended to handle the shaft several times manually, and make sure that the grease is evenly distributed over all the details of the gearbox.

When lubricating, special attention is paid to the following elements:

• Flywheel: on its surface, as a rule, intensively sticks the remnants of grass, and thickening herbal juice creates additional resistance.
• Dog of a starter coil, which in the process of turning on the drive is constantly in contact with the grooves on the flywheel. At the same time, not only mechanical wear occurs, but also the mechanochemical corrosion of the Makhovik-Sobachka compound, since the materials of this pair are different (the flywheel is aluminum, and the dog is steel).
• Bearings, if their seals are worn out, and through them the remaining lubricants are squeezed out. In this case, the unit begins to vibrate intensively when loading. This happens with trimmers of Chinese.made, so it is worthwhile to think about replacing a bearing unit with a better, for example, from the Swedish company SKF.
• Anti.sympathetic additives that do not contain toxic lead;
• Solid oils with the presence of graphite or disulfide molybdenum (the latter is preferable because the oil is completely stored for a wide range of shaft speeds);
• Only mineral (inorganic!) Oil with a high degree of cleaning.

Gear Grease Oregon or Champion EP-0, domestic compositions Oleo-Mas, Litol.24 or Azmol 158, as well as recommended by the manufacturer of a particular trimmer model for grass, fully meet these requirements.

How to lubricate a gearbox of a trimmer for grass?

In the upper part of the case where the gearbox is installed, there is a technological hole, which when the trimmer for the grass is twisted by a screw. This screw is unscrewed, and 1.5. 2 ml of fat is injected into the hole with a nozzle on the tube. If the oil was purchased in another package, then a regular disposable medical syringe is also suitable for this operation.

After that, the screw is installed in its former place. This procedure, regardless of the user recommendations, must be carried out every 10. 15 hours of work of a trimmer for grass in working mode. Other reasons for the renewal or replacement of transmission oil are independent minor repair work (for example, cleaning and flushing the gearbox before the summer season), repair of the unit, preserving the trimmer for grass for the winter, etc. D.

If the gearbox is disassembled, it is recommended to completely remove the remaining preliminary lubricants from the surface of the parts, even if there are no traces of oxidation and pollution on it. And only after that apply new oil. After applying the oil, it is recommended to turn the shaft several times manually and make sure that the oil is evenly distributed over all parts of the gearbox.

When lubricating, special attention is paid to the following elements:

• Flywheel: on its surface, as a rule, the remnants of the grass are intensively stick, and thickened grass juice creates additional resistance.
• The starting coil of the dog, which is in constant contact with the grooves on the flywheel when the drive is turned on. In this case, not only mechanical depreciation occurs, but also mechanical and chemical corrosion of the compound of the flywheel, since the materials for this pair are different (flywheel. aluminum, dog-old).
• Bearings, if their seals are worn out and lubricated through them. In this case, the device begins to vibrate greatly under load. This happens with trimmers of Chinese.made, so in the future you should think about replacing the bearing unit with better, for example, from the Swedish company SKF.

Engine starting

ICE of household braids are equipped with manual starters. The starter device is simple: a strong cord is wound on a drum that is directly or through a reducer with a crankshaft, the launch is carried out with a sharp stretch of the cord, while the drum is spent, driving a crankshaft, which in turn leads to the launch of the engine. complex models are equipped with a light launch system Flash Starter. This system provides a special clumsy spring, which is twisted through the ratchet by several stretching over the launch cord, accumulating kinetic energy. After that, a special vacation button is released from the latch, the spring is spent with the drum and crankshaft. “Light Start” provides faster launch and less energy consumption of the owner. Also, for quick starting, an additional fuel supply is provided to the carburetor with a special button. To serve an additional portion of gasoline, click on the button once. twice. The reducer of the starter with oil designed to lubricate the gearbox is lubricated.

Reducer lubricant 80 grams. Stihl

Consistent lubrication for brake system details. The product is characterized by the following advantages: excellent protection against wear; High resistance to increased loads; High adhesion (sticking); Water resistance; Corrosion protection

Car lubricant TRW PFG110 0.025 kg

High.quality science lubricant for gearboxes, hoses, transmission of coils and motorcade gearboxes. Recommended for lubrication of any mechanical devices subject to high loads. Dropproof temperature: not lower than 191 CO penetration at 25 ° C with mixing.

Gear lubricant Patriot Arsenal AR-417 855400417

Lubrication for gearboxes 250005 is a universal tool that is used in the maintenance of equipment with a gear gear (planetary, hypoid gears), as well as mechanisms operating at temperatures from.40 to 120 degrees for medium or high.

AL-KO garden lubricant for gearboxes, 100 g

High.tech nanosomic to maintain the technical characteristics of your tool and facilitate the conditions of its work features, advantages:.Specialized semi.synthetic plastic metal.sized lubricant is designed for use in equipment.

Bison 125 g, EP NLGI 2/3.fifty. 130 gr.C, lubricant for drill ZSB-125

Lubrication for reducers of the ULTRA-0 power tool is designed to serve gear gearboxes (in T. h. planetary and hypoid programs). The lubricant contains anti.sympathetic and anti.oxidative additives that ensure reliable operation of the mechanisms for debt.

Lubrication for drills (tube-suspension, 60 g) Elitech 2006.000100 is designed to lubricate the tails of drills, chisel, shoulder blades and other mechanisms of drilling equipment. Lubrication reduces friction between contacting details, protects accessories from corrosion and premature.

Lubrication for garden technology VMPAVTO ULTRA-0, 0.2 l

-457 Multifunctional DDE Multifunctional oil session for 0.1l gearboxes (NLGI 2. Graphite and Molybdenum di-Sulph multi-purpose, antifriction, waterproof lubrication with EP additives. Application: gearboxes and flexible shafts of motorcycles, trimmers and black cutters; Roller and needle bearing.

Multifunctional DDE oil-mesh for gearboxes 0.1l (NLGI 2. Graphite and Molybdenum Di-Sulph

Elitech 2006 grease name for garden technology.000300. Category of oil technology oil. Type of product lubrication. The type of engine is two.stroke and four.stroke. Seasonality is all.season. Additional information for gearboxes

Lubrication for garden technology Elitech 2006.000300, 125 g

Lubrication for gearboxes multi-purpose ECO 100 g (OG-101)

STIHL 0781120118 Lubrication of the STIHL gearbox 225

Universal multi-purpose outdadical plastic lubric lubricant based on highly purified mineral basic oil with the addition of anti-sympathetic and outfit (Ep.Extreme Pressure) molybdenum and lubricant disulfide, which has a high t.

Lubrication Mannol EP-2 Multi-Mos2 Grease 0.23 kg

High-tech oversight of the ZSB-125 bison to maintain the technical characteristics of your tool and facilitate the conditions of its work: consumable material of excellent quality for your instrumentalized semi-synthetic plastic metal-plate.

Designed for gearboxes of any garden motonels and electric saws. Carefully lubricates all the rubbing parts and remains for a long time even in open places of the mechanism. Has good adhesive ability. Significantly reduces the wear of details. Mass 225 g

Universal heat.resistant anti.symbolic grease made on the basis of highly purified mineral oils with a thickener based on a thermostable complex lithium soap with the addition of special anti.symbolic, antioxidant and anti.corrosion.

Autonomous heat-resistant lubricant Mannol 230g High Temperature Grease LC-2

Arsenal Patriot AR-417 lubricant is designed for high-speed gearboxes, also in closed gearboxes with cylindrical and conical gearboxes. Due to its fluidity, the lubricant spreads evenly in all places even with small volumes. It is significant.

Lubricant for the STIHL mower gearbox

Sergey, there is a case of a bay in the study gearbox. The gearbox of the couple (surprisingly) did not suffer, but the bearings were “offended” and burned the shaft in combat. He was broken off. The owner thought that from using the development of the gearbox would not be anything.

Ilvir, well, the grease of Stihl is not very expensive, and enough for a long time. What is it here to save 300, I have it for the third year for the third year, I squeeze it into the gearbox a little

Valentin Voinovich

And tell me what inexpensive coil can be put on a trimmer for FS38 grass, or absolutely any, even from Chinese trimmers is suitable?

Valentine, strange people however. Not an expensive coil. And then after 20 minutes of work, this coil of your coil is scattered and you are running behind the reel again. I put it again in the trash. Buy the original and don’t worry

Sergey Rudygov

How often you need to lubricate the gearbox

Alexander, it all depends on the volume of work. Someone mows a clearing at the house, someone cooks hay. The more you work, the more often lubricate. 1 time per season this is a minimum

Stihl Superlub fs in the tube 40 g. it costs 299 two seasons can be lubricated with a gearbox (9.5 g each. It is necessary there). 150 per season. it is expensive?

P.S. Why two seasons? She has two years of shelf life.

Pavlovich Petrarov

This is a protection against idiots, lubricant is enough for the entire expiration period, you cannot imagine how many reducers were diluted by the mazal workers. They drink in a cold gearbox to the eyeballs, in his work he will heat up and the lubricant will squeeze the lids of the bearings and leaks, then they have to shove it regularly, and if they forget and go to buy a new gearbox.

Viktor, firstly, the assertion that the lubricant for the entire period of its service is not specified in the gearbox. What time it is? STIHL does not explain. At the same time, gear lubrication on the site of Stilya has a shelf life of 2 years. The tube in the tube is suitable for use for 2 years, and in the gearbox will work and work for many years? So, or something? One is not consistent with the other.Secondly, on the example of the fs 55 gearbox, 629th bearing (article 9503 003 006) experiences oil starvation. There are enough lubricants for a maximum of 1-2 years, and then you need to change the lubricant in the gearbox. At the same time, take at least a serviced, at least an inconsistent gearbox. Lubrication to this bearing cannot be added without disassembling the gearbox. If you leave everything as it is, then the bearing begins to wear out, the chips appear that is visible in the composition of the oil. There is only one way out. timely (once a season) to disassemble a gearbox, clean from old lubricant and add a new one.

Vasily, they are easy to serve. One fastening screw. Removes and with a syringe through the shaft opening, press the lubricant. We collect back)))) elementary renewing the life of the gearbox)

DIY lubrication for corner grinder

Do.it.yourself lubricant for gear of corner grinders consists of the base and diluent. The basis of homemade lubrication is usually a cheer with molybdenum disulfide or cyatim-221. They have a second viscosity in NLGI, therefore, for use in the gearbox of an angle grinding machine, the basis must be diluted. As a diluent, it is best to use simple mineral industrial oil, which, for example, is I-20 oil. To obtain viscosity NLGI 0, you will need to mix approximately 70 percent of the base and 30 percent of the diluent. The resulting mixture is thoroughly mixed and ready for application to the gears and bearings angular grinder.

Timely maintenance of any electric tool is the key to long.term and reliable work. A correctly working tool is also a guarantee of security for a person who uses it. Taking advantage of the tips above, everyone can choose the right lubricant for the gearbox angular grinder and replace it, without resorting to the help of expensive service centers for servicing power tools.

Reducer device trimmer for grass

Regardless of the manufacturer and model, the modern trimmer for grass is equipped with a gearbox for changing the angle of mechanical energy between the drive shaft and the head with a fishing line. The most widespread in the benzocos were conical gears, since, unlike straight.tooth, gears with screw teeth are able to carry huge speeds, have a more smooth clutch and have increased bearing capacity.

In the duralumin case (1) there is a shaft-shuster (2) and a gear conical wheel (3), pressed on a driven shaft (4). To reduce friction forces during rotation, rolling bearings (5) are installed at the support points of the shafts. Any gear gear is a highly loaded mechanism, whose duration and reliability of which depends primarily on the lubricant. Therefore, in addition to the main components of the trimmer gearbox, the trimmer reducer includes a special hole, through which you can grease bearings and gears without disassembling the assembly.

Lubrication for reducers of trimmers

Lubrication for gearboxes 250005 is a universal tool that is used in the maintenance of equipment with a gear gear (planetary, hypoid gears), as well as mechanisms operating at temperatures from.40 to 120 degrees for medium or high.

AL-KO garden lubricant for gearboxes, 100 g

Lane lubricant 50g. MS 4115-0 for power tools, prevents the jamming and rusting of toothed gearboxes in corner grinders, peorators, rupture of part 1002 manufacturer VMPUUTO

Lubrication for gearboxes of the Ultra-0 power tool, Vfavto, 50 g

Mineral.based universal oil for lubrication of saw chains, guides, sliding bearings and stars of modern high.speed chain saws. Protects against corrosion and wear, extends the service life of equipment. Recommended for chain saws Huter

Lubrication for reducers of the ULTRA-0 power tool is designed to serve gear gearboxes (in T. h. planetary and hypoid programs). The lubricant contains anti.sympathetic and anti.oxidative additives that ensure reliable operation of the mechanisms for debt.

Vfavto. Lubrication MS Ultra, 200g tube. 1003

Drill multi-slylic lubricant for coffee machines and meat grinder Original Bosch 10g.40/200 is used in models: Bosch TE603201RW/01, Bosch TE603201RW/02, Bosch TE603201RW/03, Bosch TE603201RW/04, Bosch Te603201RW/05, Bosch Te603201RW/07, BOSCH TE603201RW, BOSCH TE603201RW, BOSCH TE60320.

Lubricant for the Makita gearbox. 30g, for peorators

Machine oil (domestic lubricant) in an oil 50 ml, suitable for use at home, for lubricating locks, door loops, various mechanisms. Protects parts from corrosion

Universal multi-purpose outdadical plastic lubric lubricant based on highly purified mineral basic oil with the addition of anti-sympathetic and outfit (Ep.Extreme Pressure) molybdenum and lubricant disulfide, which has a high t.

Lubrication Mannol EP-2 Multi-Mos2 Grease 0.23 kg

Product: grease for gearboxes; Dimensions, mm: 170x80x50; Weight, kg: 0.12; Product volume, m3: 0.00068; Appointment: for gearboxes; Volume, ml: 100

Lubrication for gearboxes of grass-shirt/bush cutter 100 grams, Husqvarna 5039764-01

Lubrication for reducers of the ULTRA-0 power tool is designed to serve gear gearboxes (in T.h. planetary and hypoid programs). The lubricant contains anti.sympathetic and anti.oxidative additives that ensure reliable operation of the mechanisms for a long time.

Performance

The choice of a benzocosille, or they are also called by the name of the cutting device. trimmers for grass, should be made from the volume of work, the more processed area, the more power is needed. For small plots, household are chosen, trimmers for middle.class grass are suitable for garden areas, for pumping a large area, especially if there are weeds or shrub thickets, a powerful professional tool is needed. park. Such a technique has an engine power of more than 2.5 liters.With. And it can work 3-4 hours a day.

The trimmer gearbox for grass includes 2 shafts. the first has a drive from the engine, and the other is used to rotate the cutting blade Motokos or Electimimer fishing line. Conical gears are made as a whole with a shaft, but there are versions with the installation of a separate part on the slotted connection. Models with different angles of the location of the teeth are available, which depends on the layout of the tool. There are modifications of gearboxes with worm, planetary or mixed (multi.stage) gears.

Shafts are installed on rolling bearings, which are closed with protective washers. Details ensure the preservation of lubricant and prevent dirt from getting on the workplace. The bearings are installed in the gearbox body made of aluminum alloy. The unit unit, consists of 2 symmetrical halves, which are interconnected by screws. To ensure the tightness of the joint, a separate gasket or sealant is used.

The lower gearbox for a trimmer for grass is installed on the tool through the planting nest. There are several varieties of the joint that differ in shape.

The most widespread are round seats with a diameter of 24 or 26 mm.

There are modifications of the tool with a square or multifaceted joint of elements. The transmission of torque is carried out through the slotting connection.

User reviews about lubricants

Experts advise using only original materials, the characteristics of which meet the requirements of the manufacturer. If there are no one, you should clarify how to lubricate the gearbox of the trimmer for the grass. Experienced users do not advise using solidol, because this material is not suitable for the temperature and speed characteristics of the node, as well as in consistency. Also, the above material does not have anti.intelligence properties.

The range of operating temperatures of the solidol is from minus 40 to 65 degrees, but even with such parameters in the process of heating, the density of the material increases, and the lubricant itself becomes rough. With emergency need to process the tool, you can use Litol-24.