Oil Flows Out Of The Chainsaw When Lying
Dacha affairs Construction and repair of materials for an apartment or house online. Articles and knowledge base. Free construction consultations
What to fill with oil for chainsaw Stihl 180 (stihl 180)
- Spend some money on the original oil. Stihl HP 2-stroke oil costs a little more, but cleaning is even more expensive.
- You can pour high-quality fuel into the fuel and Mobile 1, and a three-phase one is suitable for lubrication, in no case do not fill the workings.
- From inexpensive options, mineral oil 15-40, in winter 10-30. You can M8, for example, or M10.
Remember your personal safety when working with your chainsaw.
Remember that the quality of the oil being poured affects the operation of the chainsaw. Poor quality oil can cause ineffective tool performance and adversely affect tool parts.
To ensure that the STIHL MS 180 oil pump delivers oil without difficulty, periodically check and clean the pump. Thus, the oil supply process will be normal.
Stihl MS 180 oil supply repair
The owners of this model of the tool should be prepared for the fact that they may be faced with such an unpleasant moment as a leak of oil to lubricate the chain. Oil can leak out while working with the tool and even when it just lies without action.
What is the reason for this phenomenon? The fact is that oil leaks due to leakage in the area where the hose from the oil tank and pump is connected.
In order to solve the STIHL MS 180 oil supply problem, it is advisable to disassemble the device.
Solution to the problem:
- Check the hose, if it is damaged, then replace it with another one. Or try to degrease the hose and rinse and put on a sealant, it should work.
- Check the filter oil for breakage, clean it (if you filled in the waste)
- There may also be a clogged zapune, which creates a vacuum in the fuel tank and affects the fuel supply. The problem may be in the adjustment of the carburetor and the channels may be clogged, well, or the air filter, you need to thoroughly clean the filter and carburetor channels.
In general, the problem is mainly due to poor oil.
It is not recommended to pour oil into a chainsaw that is not intended!
Manufacturers of adhesive oils
Almost all manufacturers of chainsaws are engaged in the production of consumables for them, explaining by the fact that these products are most suitable for use in conjunction with their saws. There is no information about how true this is, but based on the experience of operating and repairing chainsaws, it can be noted that there are no significant differences in the service life of parts or at least visible wear.
But the fact is the fact, the manufacturers recommend and cannot be hidden. So, back to the manufacturers, and start with the popular Stihl brand.
How to replace the original expensive oil and is it worth
In situations where it is not possible to use original ones, they can be replaced with oil for car engines. Cheap automobile oils such as autol or diesel lubrication options are unsuitable for long-term use due to low adhesive properties.
Some owners, despite the recommendations, still use analogues, preferring to change the tire and chain more often, but here everyone decides for himself. Such oil cannot have any negative effects on the lubrication system, which means that the only difference is in the quality of the tire protection from chain friction.
What oil to use to lubricate the chainsaw chain
The answer to this question is quite simple, for this you need to open the instructions for any saw and it will indicate that you need to fill in oil that has a good adhesion effect.
What is it for? The fact is that the chain moves along the tire at a high speed, and if an oil with low adhesion is used as a lubricant, then most of it, by inertia, flies off the end of the tire and lubrication of its lower part does not occur. This phenomenon can be observed with a little experiment. Start the chainsaw, point the end of the tire towards a bright surface and add maximum gas. As a result, oil stains will appear on it, which are proof of the theory.
Chainsaw ignition system malfunctions
Problems in the ignition system in most cases become a prerequisite for the failure of the gasoline tool motor. Reasons for stopping the oil supply in the chainsaw. How can you fix oil leaks on a chainsaw. Therefore, you should start looking for defects specifically from it.
Stihl MS 180 oil supply repair
The owners of this model of the tool should be prepared for the fact that they may be faced with such a nasty moment as a leak of oil to lubricate the chain. Likely not flowing from the chain, flowing from under the linings. The oil flows right from the start. Well I do not know. Oil can leak out while working with inventory and even when it just lies without action.
What is the reason for this phenomenon? The fact is that oil leaks due to density violations in the area where the hose from the oil tank and pump is connected.
How can you fix oil leaks on a chainsaw.
One of the cases eliminating spontaneous leaks lubricating oils for saw chain made of chainsaw. Repairs.
What kind of oil should you use
It is widely believed that quality branded chainsaw oil should only be used in the engine’s gasoline-oil mixture. However, the choice of oil for lubrication is a simple matter. Anyone will do, as long as it gets to the right place.
But adding lubricant to the chain is half the battle. It is necessary that it hold on to the metal and remain on the lower edge, with which the tree is sawn. For this purpose, substances with increased adhesion are used, that is, the ability to adhere to the surface and stay on it. Oil with poor adhesion will fly off the rapidly rotating chain, splattering around uselessly. Of course, some part will remain, but it is not known whether this will be enough so that during intensive work the circuit does not overheat.
Mineral materials that provide chain and tire lubrication at freezing temperatures crystallize and thicken in the cold. This will cause the lubrication to be difficult to feed and the load on the oil pump will increase. Its service life is shortened and it may fail prematurely. In winter, it is necessary to choose synthetic materials with special additives that provide reliable lubrication in frosts down to 40 ℃. In low frosts and temperatures near zero, semi-synthetics are used.
Estimates of the use of different oils for lubricating chainsaw chains boil down to the fact that the wrong choice can increase the engine load by up to 10%. The service life of the chain and guide bar is further reduced.
Due to the fact that in recent years great importance has been attached to ecology, more and more branded oil products are made on the basis of decomposable substances. But during long-term operation, the consumption of chain lubrication can be measured in liters. And for people who are not indifferent to nature, this will be another reason to choose an environmentally friendly product. If not all the same, what your area is sprayed with and what marks remain on the wood after cutting.
How to replace expensive oil
Special branded chain lubricants have the disadvantage of their high price. Buying a liter of other expensive oil is not burdensome. And if work is coming, requiring several liters, or even tens of liters, thoughts of saving will certainly arise. The main thing is not to go to extremes when considering options. You can save on oil to such an extent that you will have to change the chain several times, or even the tire itself or the oil pump.
There are three replacement options. Firstly, you can use specialized products of little-known manufacturers for chain lubrication. But such oils still need to be looked for. In addition, there is a risk of stumbling upon a low-quality product.
Application of oils for automobile engines. They can be used as a temporary replacement, but they cannot boast of high adhesion, so the quality of their work will be clearly worse than special ones. For this reason, it is not recommended to use spindle and diesel oils. The worst in adhesion.
And we must definitely say about one more option. Working off. This is the name of the oil that has worked out its life in the engine, and is drained from it during replacement.
In fact, this is not an option at all. Metal particles are always present in mining. And if they may not damage the chain itself, then they certainly will not damage the oil pump and the entire lubrication system. On forums on the Internet, you can find a “killer” argument in favor of working off. That the Soviet Druzhba chainsaw had no chain lubrication at all and worked. So you can pour anything. And so it will do. Well, Stihl will also work with a working off or even with a non-lubricated chain. The question is how long it will work and how many chains will have to be changed during this period.
Caution for those who have a chainsaw within the warranty period. Masters of warranty workshops are able to identify cases of use of low-quality chain lubrication. Especially when using mining. Repairs under warranty will be denied immediately.
Main manufacturers
Leading manufacturers of chainsaws produce consumables and lubricants for them, including those specifically for chains and tires. All other things being equal, you should give preference to the products of the manufacturer of the chainsaw itself. But the quality of the best brands is such that the use of lubricants from another manufacturer will not have a negative impact on performance.
The most famous brands are the German company STIHL, the Swedish company Husqvarna and the Japanese company Makita. They provide a fairly wide selection of adhesive oils, among which there are:
- Mineral Stihl ForestPlus is designed to work at temperatures up to 15 ℃. Standard packing. 1 and 5 liters. For long-term work, it has recently been produced in a 20-liter container;
- Highly sustainable Stihl BioPlus is plant-based. Once in the soil, it quickly decomposes without contaminating it. The working temperature is also up to 15 ℃. Packing. 1 and 3 liters;
- For low temperatures, the semi-synthetic Stihl SynthPlus is suitable, working usable up to 25 °.
- Eco-friendly, biodegradable Bio and Bio Advanced. It is presented as a universal multigrade oil. Bio Advanced option. Improved oxidation resistance and up to 10% better lubricating properties;
- Makita. Biotop oil;
- Adhesive Champion oil.
Among the Russian brands specially for chains is ZUBR ZMPM-M. There are other, less well-known manufacturers, whose lubricating oil is noticeably lower in price.