Trimmer for grass. Caliber does not start on a cold. How to get a trimmer for grass, bay 20 g. fuel…

Trimmer does not start for grass. Why?

A gasoline trimmer for grass is an amazingly useful thing, with which you can, without unnecessary troubles, put in order not only a miniature lawn in the backyard of the house, but also to dig a considerable size of the lawn. But, like all things in this world, it has the ability to break. In this article, we will try to figure out what to do in cases where a trimmer for grass refuses to work.

So, what to do if the gasoline trimmer for the grass is poorly started or not started at all? The most common reason for such a breakdown.This is poor.quality fuel. Remember that, for example, trimmers for the grass of brands “STIHL” and “Husqvarna” are unlikely to start the quality below AI-92. Do not save on fuel, t.to. Repair of cylinder parts.the piston group can be a third of the entire cost of a braid for grass, and sometimes even half. Also, when preparing the fuel mixture, it is necessary to correctly observe the proportions of fuel and oil, which are always indicated in the instructions for the trimmer.

What to do if high.quality fuel is flooded in the gas tank, there is a spark, but the tool still refuses to start up? It is necessary to check the condition of the candle. It is located in the center of the gas mowing housing. It needs to be carefully twisted and make sure if there is a raid on it. If it is, then carefully clean the candle from the carbon and dry it.

If the lawn mower does not start even after the methods proposed above, then you need to try to remove the air filter and start the device without it. If the trimmer for the grass has not earned, clean the old filter well from dust or buy a new one.

It also happens that the lawn mower works as a maximum of 5 minutes, and then stalls and does not start until it cools down. In this case, try to open the pouring cover of a benzogornin. a suction sound should appear. After that, tighten the lid back. If you do this manipulation during the time when the trimmer for the grass has just begun to stall, then the turns will recover, and it will be possible to continue to work. If the lawn mower stalled until the cover is opened, then you just need to start it as it should be according to the instructions.

Trimmer for grass does not start after winter

How to be in such a situation? Do not worry and panic. This is a very common problem that is solved in just 3-4 minutes. Firstly, if the fuel is left in the gas tank last year, then it must be drained. Gasoline loses its octave properties after 2 weeks of downtime. Secondly, start a lawn mower after a long stagnation in a slightly different way. First you need to open the damper and pump up a little fuel mixture into the carburetor, then stretch the handle until a small resistance is sensed. After that, you can start a trimmer for the grass.

If, when trying to start a trimmer for the grass, it starts up, but immediately stalls, then the cause of this may be an air filter again. It is necessary to remove it and check if it is clogged with dust. If this is true, then it is necessary to carefully clean it or purchase a new. Also, the problem may also consist of malfunction of the ignition coil. In this case, the lawn mower is best taken to the service center.

Why and what to do if a gasoline trimmer for grass does not start

If a benzotrimmer does not start, the breakdown can be caused by several reasons. Most often, the failure occurs:

• due to clogging of air or fuel filters;
• because of the exhausted old gasoline in the tank;
• due to damage to the fuel hoses;
• due to damage to the ignition system;
• due to a short circuit of the wires responsible for inclusion.

Also, the launch of the primer and the saapon, the clogging of the carburetor and the air damper drive clogged.

The most difficult thing is to repair a benzotrimer with a malfunction of the engine, but such a breakdown is rare

Exhausted gasoline in the tank

Many trimmers left fuel in the tank after using the unit. If the cover is not closed not, gasoline can exhale and absorb moisture from the air. As a result, the combination of the mixture is reduced, and the motor does not start.

It is very simple to fix the situation. you need to remove old fuel from a gasoline trimmer for grass. Do it like this:

• Pump up new gasoline primer.
• Twist the starter cable many times.
• Pump the old fuel through the combustion chamber until the tank is empty.
• Dry the candle.

You can also simply remove and disassemble the carburetor to drain the remnants of exhausted gasoline. But it is more difficult to do this, you must have minimal ideas about the device of a trimmer for grass that does not start.

A short circuit of wires

The wires suitable for the engine are responsible for the engine. they are connected by the switch, and as a result, the gasoline trimmer for the grass is launched. Due to poor-quality isolation or permanent vibrations, the cables can be wiped out.

If a short circuit occurs, the engine is not started by pressing the button. You can eliminate the problem according to this scheme:

• The wire departing from the start button is removed from the terminal terminal of the ignition system.
• Using the tester, check the cable resistance in “Inclusive” and “off” modes.
• If there is a malfunction, a working handle of a gasoline trimmer for grass is disassembled.
• Cut or solder suitable to the motor, ignition system and wire button.
• Extract the remains of cables and set new in their place.
• Collect the hilt back.

If the gasoline trimmer for the grass starts again, the repair was successful.

Attention! In good wiring during testing in “inclusive” mode should give resistance striving for infinity.

Flowing the air filter

If the trimmer for the grass has not stalled and does not start, the problem may consist in clogging an air filter. To diagnose a breakdown, you need to extract a candle from the unit case and inspect it. If there is clogging, it will be black.

To eliminate the problem, you need to disassemble the motorcycle and pull out the filter from the body. It is cleaned in accordance with the instructions for a specific trimmer for grass, and then set to place. To prevent the problem, it is recommended to conduct preventive maintenance of equipment from time to time.

Falf in the spark plug

If the benzotrimer does not start, the failure can be caused by a candle breakdown. Diagnosis is carried out as follows:

• Twist the element from the cylinder block head.
• Carefully examine. if the contacts of the candle will be covered with a malfunction, will be covered with a black coating.
• Soak the part in vinegar solution 20% for half an hour to clean.
• Sprinkled with soda and washed with water after another 30 minutes.
• Dry with compressed air and installed in place.

In some cases, after cleaning, the candle comes into an efficient state, and the gasoline trimmer for the grass starts again. If this does not happen, you need to replace the element with a new.

If a black fog quickly appears on the new candle, the problem may consist in re.enriched fuel

The ignition coil malfunction

If the trimmer for the grass is jerking off and does not start, it is worth checking the ignition coil. Do this as follows:

• All wires turn off the block and remove them from the candle.
• Measure the resistance of both coils-in the primary it should be 2-3 Ohms, in the secondary 4.5-5.5 ohms.
• With a strong deviation of the indicators, the ignition unit is replaced with a new.

You can check the knot in another way. Instead of a candle, the tip of the discharge is inserted into the appropriate wire and the latter is connected to the motor. Then you need to set a gap with a size of 0.5-0.8 mm and twitch the starter cable. The ignition unit requires replacement in the absence of a spark, but if it is, then the malfunction lies in the candle.

Recommendations and preventive measures

It is quite difficult to start a benzotrimer with malfunctions, sometimes repair requires a lot of costs and applies of efforts. Avoid breakdowns allows compliance with prevention rules. In particular, it is recommended:

• Timely clean the ribs of the starter and channels on the housing of a gasoline trimmer for the grass;
• Before a break in the operation of the unit, drain the remaining fuel from it;
• After cleaning the gas tank, start the engine at idle to eliminate the last traces of the mixture;
• use only high.quality fuel when operating the unit;
• load a gasoline braid in accordance with the instructions;
• Before cleaning for storage, disassemble and thoroughly rinse the trimmer for grass with solvents.

It is recommended from time to time to subject the gasoline braid to be careful to identify mechanical defects. Regular preventive cleaning requires air and fuel filters of the system.

Attention! Before cleaning the gasoline trimmer for storage grass, you need to lubricate the piston group with motor oil.

The more intensively the benzotrimmer is used, the more often its individual working nodes clog

Cycle: what mistakes of beginners lead to breakdown of the engine of the trimmer for grass and exclude its normal operation

6 common mistakes with fuel

The manufacturer in the instructions clearly indicates the brand of gasoline with an octane number, oil and their proportions.

The first three errors are that the user of motorcycles violates all or one of these requirements. The motor will most likely start and work, but its resource may decrease sharply.

A small amount of oil, like its absence, will lead to the fact that the walls of the cylinder will not grease normally, and the piston rings will scratch them, and not slide.

Excess oil will simply burn, forming soot. She will pollute everything, including the piston and cylinder.

Failure gets into the valve, blocks their work, after which the motor will not start.

Will have to disassemble and clean the carburetor, or even put a new. Of course, you can try to wash the piston and the cylinder: it may be possible to bring them into working condition, but it is better not to bring them to.

The fuel mixture must be prepared with high quality and in strict proportion. The repair of a spoiled engine is expensive, about 70% of the price for a new gasoline trimmer for grass.

For the preparation of high.quality fuel mixture, I have a special container with a factory division of divisions in a set of trimmer for grass. Gasoline is neatly poured into it to the level of 500 ml, and then the oil to the required label.

An alternative method is the preparation of a fuel mixture with filling gasoline into a calibrated container, for example, a liter canister or a plastic bottle to a label, and an oil additive with a medical syringe according to its divisions.

The dosage with a syringe is more convenient, is considered the most popular way.

I recommend filling gasoline through a funnel with a narrow neck that has a filter: a metal mesh. protection against small garbage.

The prepared mixture should be well shaken and mixed until a uniform color appears. Only after that it can be poured into the tank.

If the mixture does not blame, then it will remain in the tank, and through the carburetor will enter the combustion chamber in portions with different ratios of gasoline and oil.

Fractions of clots of oil clog a candle. The motor stops, stalls, does not start. This is the fourth mistake of beginners.

It should be borne in mind that gasoline is hazardous. The risk of fire exists. Therefore, it is necessary to fill the mixture at a safe distance from the buildings, and in the case of the strait, which often happens to eliminate the causes of a possible fire. Violation of fire fighting measures. error

After pouring the fuel into the gas tank, the latter closes with a screw plug and the lack of leaks is checked. The trimmer for the grass is raised up so that the gasoline fills the cork. There should be no subterations from under the lid or from the fuel hoses.

Lack of such a check. an error can cause a fire.

There is one technical cunning that can cause a benzotrimer motor is not started due to the cessation of fuel supply. If you look carefully at the center of the traffic jam, then a round hole is clearly visible.

We turned Motokosa. Gasoline filled the cork, but does not flow through the hole: there is a sapphone inside. He is working.

On the inside, its design is clearly visible: a valve system of plastic and rubber is built.

In the usual state, the valve is pressed to the hole and the fuel does not flow. Когда бензомотор работает, то топливная смесь расходуется через карбюратор. A vacuum is created in the tank. The vacuum opens the valve of the saapon, the pressure is restored.

You should know the two consequences of a malfunction of the sapuna:

• Constantly open hole. fuel pours out of the tank during its inclinations (excess consumption and the probability of fire).
• Contamination or sticking of the valve channel is the reason that the lawn mower does not start or stalls.

Check the soundtress is easy: you need to blow it in both directions.

All about the gas tank cover, including the repair of the saapun, is shown in the video of Bogdan Shabanov.

3 additional advice associated with limited chemical resistance of a mixture of gasoline with oil:

• Do not create an excessive fuel supply. Use freshly prepared fuel mixture. In a maximum of a couple of weeks, she will lose her useful qualities;
• Prepare as much fuel as it will go to one mowing during the day. At the end of the work, drain the rest from the gas tank and burn the last drops from the fuel canal with a neglected engine;
• It is especially dangerous to leave the mixture in the gas tank for a long time. winter. In the spring, you will make sure that the engine does not start without cleaning the carburetor (gasoline evaporated, the oil thickened and glued the valve).

In more detail, the technology for eliminating these malfunctions shows in its video video “Chinese lawn mower is not started” Sergey Lesnik. Pay attention to the fuel filter.

To adjust the work of the carburetor allows a special screw, but it is not worth it to twist it without need: the factory adjustment is accurately exhibited. It is better for novice users to contact the service center.

Cycle: why the piston may not move inside the cylinder

The flywheel of a trimmer for grass, aka Magneto’s rotor with magnets, is fixed on the shaft with a key.

This is usually a reliable connection. Under the flywheel there is a sealing oil seal that does not pass the oil from the crankcase out. But when he wears out, the craftsmen have to remove the flywheel and change the oil seal with a new.

Otherwise, the oil flies everything, including the air filter.

At the same time, it is not so easy to remove the key: people make special pullers.

When looking for information on trimmers, I came across a video of one master, who was brought into the repair of the lawn mower, where the flywheel gap was absent. Perhaps a factory marriage. Naturally, such a motor will not start.

A similar reason should also be borne in mind.

The lawn mower is not started on a cold

When starting a cold motor, it is not recommended to press the gas. Having tilted the lawn mower so that the air filter is on top, click on the fuel suction button 5-6 times, install the function of switching functions to the Start position, pull the starter’s cord several times until the motor starts up. After a few seconds of the engine, turn off the start system.

If the lawn mower was recently at work and did not have time to cool down but did not want to start. press the gas trigger, sharply pull the starter’s cord several times until the engine is started and only then the gas trigger is released. If a lot of time has passed and the lawn mower managed to cool, then it must be started as with cold. If the above methods did not help, the lawn mower did not start, then you should contact the service center.

Repair and service of garden equipment.

Specialized Service Center “AgrotechService”. Warranty and post.warranty service of the equipment of world manufacturers! Attention! Information for users!

Cleaning the soundtress

Often the engine of branded models of trimmers stalls as a result of clogging of the soundtress. The main task of the specified component. Setting pressure in the fuel tank. In the case of contamination of the node, a vacuum is formed here, which significantly complicates the supply of fuel. Eliminating the malfunction allows the cleaning of the saapon using a conventional sewing needle.

The stable functioning of a trimmer for grass can be impaired as a result of laying dirt in the graduation canal or the formation of a blockage on a muffler grid. This problem most often occurs during the operation of older generation trimmers. The issue is being solved by dismantling the anti.diploma mesh and its cleaning.

How to prevent sudden breakdowns during the operation of a trimmer for grass?

So that the unit is always in a functional state, it is worth observing several simple rules:

• Carry out timely, regular technical inspection of the main mechanical nodes of the device.
• Refill a trimmer for grass with exceptionally fresh fuel, the quality and origin of which is not in doubt.
• Check after each use of the tool, whether oxides and soot on the surface of the ignition system were formed.
• Avoid the strong load of the trimmer for grass during work.

In order for the unit to remain in a working state, it is necessary to properly prepare it for storage in the winter period. First of all, you should completely disassemble the tool, and then perform washing and cleaning the constituent elements. It is also important to examine the functional blocks for damage, with the need to eliminate the deformation of the parts, all kinds of distortions, gusts of materials.

Placing a trimmer for storage grass, it is worth filling the gearbox with a sufficient amount of oil. Then you need to clean the air filter, partially disassemble, blow and rinse the unit engine. Having dried all the mechanisms, lubricate moving elements. To carry out the processing of the piston system with oils, it is necessary to first extract the spark plug. Then you need to move the piston to the extreme position, then pour a small amount of oil into the candle hole and make scrolling the crankshaft. If the gasoline trimmer for grass in the offseason is not planned to be stored in the house, it is recommended to tightly wrap the engine of the unit with an oiled rag. This will avoid the development of corrosion on the surface of important components of the mechanism.

Dry and wet candle what it means and how affects the launch of the motor

Most of the owners of the tools immediately resort to checking the state of contacts of the spark plug. This is done in order to understand, by the state of the candle, what could be the reason for the impossibility of starting the engine of the lawn mower. According to the state of the candle contacts, you can draw the appropriate conclusions about what can be the cause of the malfunction. Diagnosis of the spark plug on the trimmer is performed in the following order:

• The spark plug unscrews, after which it is subject to inspection. The ideal state of the electrodes. if they have a brown carpet (brick color). If the candle is wet, has a black or white fog, then this indicates the corresponding faults
• If the candle is wet, then in the combustion chamber there is a portion of unbroken fuel, which does not need to be drained. Clean and dry the contacts of the spark plugs, then make sure of its serviceability. To do this, connect it to the immunity, and place it not the surface of the cylinder. Turn on the ignition and pull the starter handle easily. In this case, the candle should issue a quality and constant spark. If the spark is weak or it is not at all, then the spark plug should be replaced
• A trimmer does not start for grass may not be started due to a large gap between the contacts of the candle. The gap between the electrodes of the spark plug should be in the range from 0.7 to 1 mm. Special probes are used to set the gap

It is interesting!Dry candle contacts by pumping it is strictly contraindicated, since this method will lead to damage to the details. If there is a spark on the candle, but the trimmer for the grass does not start, then the reason is the supply of the fuel mixture in the combustion chamber. To make sure this, you should perform the following actions:

• Dial in a cap made of PET bucks or in a syringe of 20 grams of fuel
• Pour it into the combustion chamber through the candle hole
• Twist the spark plug
• Put on a candlestick and start the engine

If the engine of the lawn mower starts after the actions performed, then the cause of the malfunction should be sought directly in the fuel line and carburetor. If the motor does not start even after the actions done, then you need to check the serviceability of the high.voltage wire. The high.voltage wire, like the spark plug, refers to consumables. If there are suspicions of a malfunction of the armor of the trimmer for the grass, then it should be replaced. If, after the actions done, it is not possible to launch the engine of the lawn mower, then the following recommendations must be taken into account:

• If there are doubts about the serviceability of the spark plug and high.voltage wire, then it is recommended to immediately replace them
• Check the serviceability of sparking, and if there is no spark on the new candle, then the breakdown is associated with the ignition unit. the failure of the coil is out of order
• The ignition coil is not repaired, but changes. If the diagnosis really indicates a malfunction of the ignition of the lawn mower, then it is not difficult to replace it with your own hands

If there is a candle on the spark, and at the same time it is dry, and the trimmer for the grass does not want to start, then we move on to check the next node. air and fuel filters.

It is interesting!If the candle electrodes have a red or pink color, then this suggests that the composition of the fuel used contains a large number of additives. You should abandon such fuel by changing a gas station or a brand of gasoline.

The most frequent malfunctions of gasoline lawners

It is necessary to check the fuel. It is possible that due to its absence, the engine will not start. The reason for the refusal of the engine may be a candle. The car is removed and the engine is launched again.

Силовой агрегат завелся, но сразу заглох

The reason for the refusal of work may be an insufficient amount of oil in the motor crankcase. Because of this, the piston or crankshaft often jams. Try to hand it manually. Often such actions give a positive result. Then, before repeated start, it is necessary to add the missing oil.

To revive the unit, it may be enough only to pump up fuel with a plain in a carburetor. The speed adjustment to the maximum will help. Then pull the cord smoothly on yourself. Twenty centimeters will be enough and a sharp jerk jerk over yourself.

Often problems arise With improper location of the air damper

, when the first trial start of the motor is produced. It is recommended to completely open the damper.

can serve as an air filter. It is necessary to disconnect the wire from the spark plug on the disconnected lawn mower. Then remove the filter, having previously unscrewed the lid. Rinse it with gasoline and dry it. Put in place, carry out re.launch of the motor. If the actions are unsuccessful, replace the old filter with a new.

We remind you. the planned replacement of the air filter is carried out after 25 hours of operation of the equipment. If the lawn mower works on the battery, you need to check the level of its charging.

Can Check the safety lock

If the installation is carried out incorrectly, the lawn mower will not start. Experts advise regularly inspecting the lower surface of home appliances. Various malfunctions in this part may cause engine failure to work.

If your efforts are unsuccessful, contact the service center for the consultation and help of specialists who will be able to carry out any repair of the lawn mower, in particular it.

Not starting on a cold trimmer for grass. we eliminate the cause

On the cold.The reason is an air leak that does not allow fuel to download. In the camera.

After several jerks, he will start and stall, which is a normal phenomenon. What to do when the fuel was definitely normal, there is a spark, but a trimmer for grass does not start a gasoline? Putting the damper to the working position, start the tool again and start working.

Typical malfunctions

The most frequent breakdowns arising during the operation of the unit are:

• the engine does not work, the trimmer is not started for grass;
• The engine manages to start, after which it does not hold back and stalls sharply and for no reason;
• The rod of the motorcycles vibrates greatly;
• The gearbox overheats greatly;
• Weak turnover at the cutting fishing line.

Before you start repairing, study the instructions that must be in the kit to correctly diagnose

And again the carburetor.

Well, even if after such bullying your trimmer does not start for the grass, you can’t do without disassembling the carburetor. It may very well be that everything is to blame for the gathering of the needle in it. In any case, the disassembly and washing of this capricious mechanism certainly will not hurt.

In general, when a trimmer for the grass began to be capricious and stall, it is advisable to carry out complete prevention: to completely change the fuel mixture, try another oil, and also mandatory change the candle. The gasoline trimmer for the grass does not start? Reasons and decisions on. Practice shows that in many cases, it is precisely cheap low.quality candles that are to blame.

We examined the most typical reasons why a trimmer is not started for grass. If the matter is something more “exotic”, do not pass the campaign in the service center. You will probably find smaller and obvious breakdowns yourself.

A new trimmer for grass is not started by gasoline causes

The gasoline trimmer for the grass does not start? Prerequisites and solutions on the example of Elitech T750

In general, a similar conversation should start with the fact that after the purchase of a garden bench instrument, it would be better to first familiarize yourself with the annotation attached to it. Gasoline trimmer for grass filter or buy a new. trimmer for grass does not start. Then many troubles could have been avoided. But since this happened a gasoline trimmer for grass does not start, then you need to find sources of inoperability. And in this article we will see the main prerequisites why the trimmer for the grass is not started by the example of the Elitech T750 model, as well as tell the general advice on operating such a tool.

Start with obvious! We will figure out how to correctly start a gasoline trimmer for grass. Maybe such that the reason lies here.

First you need to bring a red toggle switch on a trimmer bar for grass to position “i”. This means the inclusion of power supply. Then you need to switch the fuel supply lever on the carburetor and use the fuel “suction” button (looks like a pipette, is on a carburetor). If the engine does not start or stalls quickly, not a trimmer for grass and turnover. This is necessary to supply gasoline to the engine. Fuel supply lever to return to its original position. At the end, sharply pull the starter handle on yourself. The trimmer for the grass should earn. Try it several times if the first time does not work. If after such manipulations the situation has not changed and a gasoline trimmer for grass does not start, then it is worth it to inspect it on your own first before you lead to the service center. There are two main reasons why the garden trimmer is not started:

Why is a trimmer not starting for the grass: the main malfunctions and their elimination

As already noted, such situations are characteristic of trimmers who were inactive for a long period of time. Therefore, after detecting the problem, you need to immediately take up the search for a malfunction.

Fuel as source of problems

The first stage is checking the presence of fuel and its quality. First of all, they are convinced that there is a fuel in the tank. Those who have acquired the unit recently, often forget that the trimmer for the grass needs refueling. If there is no fuel, then the equipment simply cannot work.

If there is a fuel in the tank, but the trimmer does not start for the grass, then the owner needs to check whether he is acting correctly. In this case, it is recommended to study the instructions. If the launch is made correctly, then the malfunction can cause the inappropriate quality of the mixture.

• Oil. It should be special. intended for two.stroke engines. It is not recommended to save on the product, since the life of the equipment depends on the mixture. Trammers for grass with a four.stroke engine require pure gasoline, it is not mixed with butter.
• It is necessary to use not only high.quality gasoline, but also the brand that is recommended by the manufacturer of a particular model. If it is not possible to find out what fuel is necessary, then it is recommended to choose either AI-95 or AI-92, and the last gasoline is a favorite, since the first has additives that react with two-stroke oil. Other brands do not advise using.
• The correct preparation is shifted for a benzotrimer. It is noted that at first this stage is paid to maximum attention, but over time, kosari begin to mix the composition “by eye”, and this is already a serious mistake. The correct ratio of gasoline and oil is 25: 1. For a liter of the first, 40 ml of the second, two.stroke. Motor oil intended for a car is an inappropriate option, since at high temperatures the liquid loses (partially) lubricating properties.

The correct storage conditions of the fuel mixture are important. To save time, some owners prepare it for the future to use it in the coming weeks. This option is contraindicated, since the prepared fuel mixture quickly becomes unsuitable. The reason is the precipitation of oil loss. With this change, both oil products lose their properties. Even repeated stirring is not able to restore the initial quality of fuel. Therefore, they recommend preparing a certain volume: 2 liters, no more.

If everything is in order with gasoline and oil, then they start diagnostics. to check the spark plug.

Candle and its condition

At this stage of diagnosis, you need to stop in more detail. Most experienced owners who are already familiar with the question of why a trimmer for grass does not start, first of all check the state of contact contacts. Diagnosis of this element is carried out as follows:

• First, the spark plug is unscrewed, then inspect. If the electrodes are in perfect condition, then they should have a carpet whose color resembles a brick. Wet element, or white, black plaque on contacts indicates the presence of any malfunction. Pink and red electrodes. proof of a large number of additives in fuel. Such a mixture must be replaced.
• In the event that the spark plug is wet, this means that the combustion chamber has unbroken fuel. It is left in place. Candle contacts are cleaned, then dried (calcination is prohibited). After this stage, the candle is connected to the nurser.
• Then the ignition is turned on, the frontier handle is pulled. When everything is in order with the element, it must issue a constant spark. If it is weak or completely absent, then the verdict is one. you need to replace the spark plug.

There is another reason why a trimmer is not started for grass. This is a big gap that appeared between the contacts of the candle. A distance of 0.7-1 mm is considered normal. To correctly adjust the gap between the electrodes, use special probes.

If there is no such device, then the folk method is used. A razor blade breaks, folds its parts together. Then this “probe” is inserted between the contacts. Ideal. blades that enter tightly.

The problem is in the fuel and the carburetor

If there is a spark, and a trimmer for grass still does not show signs of life, then nuisance can lie in the fuel supply to the combustion chamber. To make sure that this node is to blame, they perform such actions:

• They are typed in a syringe or poured into a lid from a plastic bottle of about 20 ml of fuel.
• Then, through the candle hole, the fuel is neatly poured into the combustion chamber.
• The candle is returned to the place, put on the imminent, the engine is launched.

In the event that the trimmer has started for the grass, the problem may be in the fuel and carburetor. Когда эффекта от проделанных манипуляций нет, диагностику продолжают — проверяют высоковольтный провод. At the slightest suspicion, this consumption element is replaced by a new.

What to do if the engine is a trimmer for grass still refuses to work? In this difficult case, you can follow the following recommendations:

• In doubt about the candle and the high.voltage wire, it is better to immediately replace them.
• If, when checking the new sparkling candle, it was not possible to achieve a spark, then it is almost possible to say with complete confidence that the ignition unit is faulty. the coil came out of the system.

Check its serviceability simply: they twist the candle, then it is led to the trimmer body for grass. If there is no spark when the starter jerks, or it does not appear every time, then a new coil is required. This element can also be replaced independently.

How to avoid most problems?

The work of this seasonal equipment is very affected by its proper storage. over, this applies not only to a long “rest” in the winter, but also of short intervals of inaction. To protect yourself and the technique from problems, you need to adhere to a few simple recommendations.

• Before sending on a well.deserved rest, a tank trimmer for grass is freed from fuel remnants. To remove the entire mixture, the lawn mower is launched and allowed to work until the engine is stalled.
• The first operation after “winter hibernation”. pouring a small amount of oil into the candle hole. Before that, the piston is moved to the extreme position. Such a lubricant will facilitate the launch and prevent premature wear of the details.

Before starting working with a motorcycle, they must check the candle and all the main equipment components.

Reasons why the trimmer for grass does not start is quite a lot. But most of them can be detected and fixed independently. The main thing is the correct diagnosis, attentiveness and sequence of actions. And about how you can cope with problems, the master from the next will tell in detail