VIKING lawn mowers problems. Lawn Mower Overheating: What Causes It and How to Fix It

The VIKING Lawn Mower Starts And Immediately Stalls

If at the first start-up, your new lawn mower refuses to start, try the following: based on the outdoor temperature, set the air damper to the appropriate position (at a temperature of less than 30 ° C – “the damper is closed”, above 30 ° C – the half-closed position), then pump it into the carburetor fuel and gently, but rather sharply pull the starter handle until you feel some resistance. Repeat these steps in the same sequence several times. A completely new tool should start. If this finally happened, you can safely get to work, having previously fully opened the shutter.

If the lawnmower is no longer new, then it is necessary to start its inspection from the gas tank. If the device has not been put into operation for a long time, then it is necessary to drain the old gasoline, which has the feature of “exhaling”, i.E. Lose their octane properties, and pour fresh fuel mixture. The ratio of gasoline / fuel, as well as their necessary brands are usually indicated in the instruction manual of the tool.

Now you need to check the spark plug – either the problem is in it, or in the fuel system. The candle must be carefully unscrewed and its condition evaluated. If the candle is heavily filled or there is black soot on it, then it must be removed, cleaned and dried. Drain excess fuel, if any, from the spark plug holes, drain the cylinder itself, then screw in a dried or, even more desirable, a completely new candle. If the candle was initially completely dry, you need to look for a problem in the fuel supply system. First, check the fuel filter. To do this, disconnect the suction hose and remove the dirty filter from it, clean it and reinstall it, or replace it with a new one. If this does not help, you should contact the specialists of the service center.

Doesn’t start after winter

In this case, you just need to drain the old and, possibly, even frozen fuel and fill in the freshly prepared mixture. Then you need to perform the same manipulations as during the first start of the lawn mower.

Starts up and stalls

If the mower stalls after starting, check the air filter. When this filter is very clogged with dust, it ceases to allow the necessary amount of air to pass into the carburetor and allows dust to enter the fuel mixture. Carefully remove the contaminated filter, clean and rinse with gasoline. If the air filter is clean, and the tool stalls anyway, then it is better to contact professionals to determine the cause of the malfunction and to eliminate it.

• The blog
• About Service Center
• Serviced Brands
• Diagnostic and repair prices
• Delivery
• Spare parts
• Contacts

Repair and service of garden equipment.

Specialized Service Center Agrotechservice. Comprehensive warranty and post-warranty maintenance of landscape gardening and public utilities of world manufacturers! We carry out the sale of spare parts with delivery throughout Russia!

When caring for the lawn, you should not trust the English proverb that it will become ideal only after 200 years of constant mowing. Russian owners of private territories will not wait so long, because with proper care the site will have lush and dense grass next season. It remains only to choose the right tool for care. There is no need to mention the grandfather’s spit, because you cannot achieve a level lawn with its help.

Overview of lawn mower models from VIKING: MV 650 VE

If you are interested in the gasoline model, then you should consider the option of a lawn mower, which was mentioned in the subtitle. You will have to pay 67,000 rubles for it. This equipment is a self-propelled model that works due to an engine with a power of 2.3 kW. In one pass, you can mow the grass 48 cm wide.

Additional properties

The case is made of aluminum, which indicates the ease of construction and the long life of the tool itself. This self-propelled VIKING lawnmower can be used to care for an area of ​​up to 2000 m2. Tires with a profile are mounted on the drive wheels, which provides good traction and stability. The frame has a rigid structure, thanks to which it retains its shape, which is true even with intensive and frequent use.

Characteristics of the model MV 650

Considering the model of the lawn mower MV 650, you should pay attention to its technical characteristics. Among others – power, it is 3.2 liters. With. This self-propelled model has a grass catcher and an autostart system. The mowing height reaches 85 mm, while the minimum bevel is 30 mm. You can adjust the modes in 7 steps.

The design has a rigid grass catcher and the ability to choose the speed, which not every lawn mower can boast of. The manufacturer provided for the presence of a self-adjusting folding handle, as well as wheels on bearings. Grass is ejected from behind.

Height adjustment is central. The device works due to the gasoline engine of the 675 RS series. The unit weighs 45 kg. You must consider that it does not have large rear wheels. The design provides for the option of mulching. The drive is rear.

Video: The VIKING Lawn Mower Starts And Immediately Stalls

Reviews on the self-propelled model MV 650

• Comfortable work;
• The presence of a knife with flaps;
• Strength;
• Power;
• Directivity down air holes.

If we consider the positive features in more detail, we can say that comfortable work is provided by a motorized wheel drive. You can mow grass even on large areas and slopes. In order to start work, it is necessary to turn the key, which starts the mower.

The VIKING lawnmower knife has flaps. Thanks to the powerful air flow created in the aerodynamic type casing, the grass rises before mowing, which means that the result of cutting will be excellent. Consumers also like the high durability of the case. It is made of aluminum, so it has a low weight and impressive strength. The surface is covered with a powder composition at the manufacturing stage, so the design gains the ability to stably tolerate the effects of corrosion and fuel.

The VIKING lawn mower has, according to consumers, become a popular equipment during its existence on the market. This fact cannot be called random, because it is due to many positive features. Among others, consumers highlight the presence of a grass catcher fill indicator. Thanks to this addition, the structure will be able to signal to the operator when it is necessary to empty the tank from grass.

You can mow using the described models, even along the curbs and walls, this feature is provided by the plastic overlays that the case is equipped with. The latter, by the way, has special handles for carrying. This also makes loading easier, for example, in the trunk of a car. There is also a handle on the front that will allow the lawnmower to be moved from place to place.

Starting equipment is facilitated by the availability of automation. When the engine is cold or hot, with the help of the described system you can ensure a leak, which will make the start of work easier. You can change the cutting height of the grass thanks to the practical handle on the body. This supplement, according to buyers, is very useful. You can adjust the speed smoothly. It is impossible not to mention the durability, as well as the reliability of the wheels, which have a double bearing. Leading equipped with profile tires, which indicates exchange rate stability.

Overview of the Lawn Mower Model MV 2.2 R

You can buy this model of gasoline lawn mowers for 23,000 rubles. It is a maneuverable lightweight unit that is suitable for the maintenance of areas up to 1,500 m 2. The mower has a professional engine.

The machine has a compact size, so it easily goes around obstacles. Keyless locks allow folding the handle, which saves space during transportation and storage. You can adjust the mowing in 4 modes, this allows the operator to achieve the desired result.

Specifications MV 2.2 R

The VIKING MV 2.2 R lawnmower has a capacity of 2.2 liters. With. The model does not have a catcher, it is not self-propelled. The device weighs only 22 kg. The fuel tank holds 0.8 liters. The maximum mowing height reaches 85 m, while the minimum mowing rate is 28 mm.

Height adjustment – axial. The housings are based on sheet steel. The dimensions of this VIKING lawn mower are 1240x490x1000 mm. Grass is ejected from behind. The spindle speed is 2900 rpm. The engine capacity is 125 cm 3. Power in kilowatts is 1.6. There are no large rear wheels in the design, as well as autostart options, but there is mulching.

Model reviews

When consumers consider the MV 2.2 brand lawn mower, they note that it has many advantages, among which are:

• Durability;
• Shredding mowed grass;
• The ability to adjust the cutting height;
• Convenience of storage.

As for durability, it is also provided with double-bearing wheels, which are reliable and have a long service life. Customers also like the fact that the model of equipment has the ability to grind grass.

The mulching function frees the operator from the need to remove mowed grass. Mulch will be thrown into the area, enriching the lawn with nutrients. The described VIKING lawn mower, the price of which is reasonably reasonable for most consumers, provides the ability to adjust the cutting height. This function is implemented in the adjustment on the axis of the front and rear wheels.

Convenience of storage is the presence of a folding handle. Consumers additionally emphasize that the gasoline engine in the design has a long service life. But the case reliably protects the internal components of the lawn mower from damage.

For some consumers, the VIKING Electric Lawn Mower is the best solution, especially for those land owners who care for the lawn within the city. The described model is used for small areas, it is quiet and easy to manage. Its power is 0.9 kW, and the mowing width is 33 cm.

The equipment weighs only 11 kg. This feature, according to consumers, facilitates the transfer and transportation, as well as loading and unloading. The maximum cutting height reaches 57 mm. The cultivated area is 300 m 2. According to customers, this is quite enough for private areas. The VIKING Electric Lawn Mower has central height adjustment. She is not self-propelled.

On sale you can even find cordless models of lawnmowers from the manufacturer VIKING. One of them is MA 339, which you can purchase for 25,000 rubles. Cutting width reaches 37 cm. The set includes a hard grass catcher and central adjustment of the cutting height. You can adjust the last parameter from 30 to 70 mm.

The equipment weighs only 12 kg. The design works due to the engine at 600 watts. This model is suitable for areas of small and medium areas, the size of which reaches 6 acres. You will no longer depend on gasoline. This also applies to the lack of cord limitations. The battery is universal, so it can be used in conjunction with the VIKING and STIHL tools. Among these tools should be highlighted:

With the VIKING cordless lawnmower, you can process small areas in a short time, which is ensured by the mowing width. The equipment guarantees convenient and easy operation. The case is made of shockproof plastic, which makes the device more durable. The design has special knives, they create an air flow that provides better mowing. According to customers, this also contributes to the optimal filling of the grass catcher.

Cost of spare parts

The VIKING lawn mower, which is based in Austria, is of high quality. However, even such equipment may require replacement of tools over time. The supplier recommends using only original spare parts, among them you should highlight the mulch, which you can purchase for 2550 rubles. But the knife blades cost only 532 rubles.

A circular knife will cost the consumer 3571 rubles. But a multifunctional knife costs 1886 rubles. Spare parts for the VIKING lawn mower are expensive, but only those supplied by the manufacturer should be used, because otherwise the equipment will not last long.

Instruction manual

Before starting any maintenance work on the equipment, it is necessary to disconnect the plug of the spark plug wire. All screws, bolts and nuts must be tightened to failure, the only way you can be sure that the device will work reliably.

After reading the instructions of the VIKING lawnmower, you can understand that when a cutting tool collides with an obstacle, stop the device and inspect it. Mowing tools should be inspected regularly for wear. They must remain operational.

Lawn Mower Overheating: What Causes It and How to Fix It

Lawn mower overheating is an issue often neglected by users because after cooling it down, you may proceed with another round of mowing. It may be caused by the engine itself or even the mowing deck etc. and will be solved mostly by maintenance.

Note that continuing to use it can lead to more damage, if not the total destruction of your lawn mower, especially its engine.

Overheating problems can be addressed even if you’re not an expert mechanic. Just by reading the manuals and this article, you could solve the problem right away. So keep reading on to find out more about lawn mower overheating.

• What Reasons Cause Lawn Mowers Overheating?

• – Clogged Engine Parts
• – Cooling Fins Are Blocked
• – Muffler is Not Working Correctly
• – Incorrect Amount and Use of Oil
• – Can Blunt Blades Be to Blame for an Overheating Lawn Mower?
• – Mower Deck is Full of Debris
• – A Loose Engine Guard
• – Defective Engine Parts
• – Overworked Machine

• – Clean All Parts of the Lawn Mower
• – Replace or Fix the Defective Parts of Your Lawn Mower Engine
• – Observe Intervals During Your Mowing Session
• – Use the Correct Type of Engine Oil
• – Maintain the Correct Engine Oil Level

• – What Can I Do To Cool Down My Lawn Mower?
• – How Long Does It Take for a Lawn Mower To Cool Down?
• – Can Water Be Used To Cool Down Overheated Lawn Mowers?
• – How Do You Know Your Lawn Mower is Overheating?

What Reasons Cause Lawn Mowers Overheating?

The reasons that cause mowers overheating are many – among them are clogged engine parts and incorrect amount and use of oil. But, before knowing what causes lawn mower overheating, first identify what type of mower you have. For a start, is it the riding mower or the walk-behind type?

Lawn mower overheating is really a problem that is experienced by almost all lawn mower owners. In order to fix it, you need to know its causes first.

– Clogged Engine Parts

Dirty and clogged lawn mower engine parts are a common cause of mower overheating. This happens because the air cannot flow freely (in air filters, too) because of the blockage caused by debris and filth from previous mowing works. Easily clogged parts include the lawn mower cooling fins, cutting decks, and air vents of the mower engine.

– Cooling Fins Are Blocked

The cooling fins are those small plastic (or metal) materials near the spark plug. Through their movement, hot air dissipates from the engine. These generally get dirty very quickly and have to be cleaned regularly.

– Muffler is Not Working Correctly

The muffler removes the hot exhaust gases in the mower. If it is dirty it will not be able to do so properly and the outflow will decrease. When this happens the lawn mower may overheat and stall. It can be cleaned with a water and a brush. If they get too dirty you will have replace them.

– Incorrect Amount and Use of Oil

The mistake of using engine oil is not uncommon among mower owners. Engine oils aid in lessening friction between the moving parts of the engine. Having only a small amount of engine oil or not being able to reach the appropriate engine oil level would eventually result in engine overheating as friction increases.

Another engine oil mistake that could result in overheating is the use of unchanged oil. Oil becomes stale or bad when it is not changed regularly. It could also result in a thicker oil texture, which makes the engine parts work harder. Also, there are people who tend to pour (aware or unaware) the wrong kind of engine oil into their machine, which is a big mistake in the first place.

Engine oil comes in different varieties, depending on the engine type and the environment or the climate in which the machine is to be operated. SAE 30- is used in regions with warm temperatures.

Needless to say, you need to determine first what engine oil is appropriate for your mower. Negligence to do this could be the cause of walk-in or riding mower engine overheating.

– Can Blunt Blades Be to Blame for an Overheating Lawn Mower?

Yes, blunt blades can be to blame for an overheating lawn mower. When your blades are dull it causes a greater strain on the machine, therefore making it overheat. A sign to help look out for dull blades is that the grass seems to be torn rather than cut.

– Mower Deck is Full of Debris

Meanwhile, the cutting deck occupies the largest part of your mower as the blades are underneath this. When grass debris and other clippings accumulate in these parts, clogged air intake happens.

A mower deck full of debris will cause your engine to work harder and possibly overheat, just like with dull blades. The blades will start to get stuck and jam – but, the machine will just try to continue anyway and that will cause friction and overheating.

– A Loose Engine Guard

A loose engine guard can contribute to an overheating lawn mower. If the engine guard has come loose for whatever reason and it is not in its proper place you will not have the cool air kept around the engine as it should be. Overheating will ensue.

– Defective Engine Parts

Lawn mowers are among the most reliable pieces of equipment that you do not need to buy or replace often. With extra care, it could last for years. However, with long service, it is unavoidable that some parts would become defective. These defects may become the source of overheating in the machine.

A leaky gasket, a detached engine shield, broken fins, missing screws, and other minor defects that you may think of as inconsequential may, in the long run, interfere with the smooth operation of your lawn mower. Such defects could make the lawn mower overheat, or they could altogether stop the machine’s operations.

– Overworked Machine

Sometimes, a mower overheats simply because it has worked non-stop. Other reasons include being exposed to different weather elements, working on wet grasses and not making sure that the turf is dry first before starting the machine the next time, and cutting dense grasses not specified in their capacity.

These scenarios could also lead to the heating of the engine and, when not addressed, could result in overheating and, worse, is engine combustion.

How Do You Fix Overheating Lawn Mowers?

To fix overheating lawn mowers you must clean all the parts of the mower, replace or fix the defective parts, observe intervals during your mowing session, use the correct type of engine oil and maintain the correct engine oil level.

– Clean All Parts of the Lawn Mower

Practically, ensuring that your mower is clean is the first step in avoiding overheating. Free it from all the debris and dirt that congested all air filters and air vents. Knock off the stubborn dirt clinging to the insides of the machine.

Vacuum cleaners, sprayers, and even old toothbrushes can be used to reach out that deep-seated junk inside. Regular cleaning of the cooling fins and air filter will not only benefit the machine but also you and your yard in the long run.

– Replace or Fix the Defective Parts of Your Lawn Mower Engine

Whether it is a detached screw, a flapping engine shield, or cooling fins, they must be fixed immediately to avoid further trouble. Leaky gaskets of your carburetor could be replaced either by you or through the nearby shop. Replacing belts on your hover mower is also another way to minimize the risk of overheating.

– Observe Intervals During Your Mowing Session

Let the lawn mower have a break from a day’s work, and do not force it to cut wet grass. Letting the grass dry before mowing your lawn is a sure way to ensure that your mower will not be damaged. Also, let it cut grass according to its specification.

For your overgrown and dense yards, have the grasses cut twice or thrice so as to minimize the force exerted by the machine in doing the tasks. Adjusting the cutting deck to the appropriate level of the grass you want to cut would do the trick.

– Use the Correct Type of Engine Oil

The small engine of a lawn mower relies on oils to achieve maximum operation. Thus, feeding it with the correct oil type is an absolute requirement. Lawn mower overheating could really be minimized when following the necessary brand requisites.

– Maintain the Correct Engine Oil Level

See to it that the engine oil does not go below the minimum level required for the machine to function. Engines that are already low in oil are on deck for overheating, as friction and overworked parts would occur because of the lack of lubrication. Checking your oil level gauge regularly and keeping an extra stock will be a big convenience for you.

Frequently Asked Questions

– What Can I Do To Cool Down My Lawn Mower?

You can use air cooling to cool down your lawn mower. Turn it off first, and then cool your mower down by just letting it sit. See to it that no flammable materials can be found nearby. When it is cold, you can check for the cause of its overheating.

– How Long Does It Take for a Lawn Mower To Cool Down?

How long it takes for a lawn mower to cool down depends on a number of factors – the surroundings, particularly how airy it is and how much cover you were able to remove or detach from the mower before cooling it off.

– Can Water Be Used To Cool Down Overheated Lawn Mowers?

No, water isn’t recommended to cool down a lawn mower. The engine and all the metal parts could crack. It is better to allow overheated lawn mowers to cool down naturally by turning them off and leaving them alone in a well-ventilated area for at least 30 minutes.

– How Do You Know Your Lawn Mower is Overheating?

To know if your lawn mower is overheating you must observe certain signs. However, the first, and most obvious sign is that it simply cuts out. Other signs you may observe are smoking and you can physically feel the heat from the engine.

Conclusion

Small engines like that of your lawn mower could overheat due to various reasons. The ability to identify what causes the lawn mower to behave like this can help solve the problem.

• A common cause of overheating among lawn mowers is grass cuttings, rubble, and other debris filling the engine.
• These scraps are stuck in air intake manifolds and parts with air vents, thus preventing the smooth movement of air within the engine.
• The use of bad or stale oil, wrong choice of engine oil, and inadequate oil level would also cause the overheating of the engine.
• Overheating could be fixed by having regular checkups of the engine, using the correct amount and type of engine oil, and learning how much the lawn mower could work.

Lawn mowing is a satisfying activity as long as you don’t encounter any issues. Overheating of lawn mowers could be readily fixed if you know the cause, and act on it prudently to save more time and money.

New VIKING Mowers plus behind the scenes at the Kufstein HQ

One of the upsides of spending most of my ‘free’ moments updating GadgetyNews are the invitations to attend events. The latest one was over in the Tyrol, Kufstein to be exact.

VIKING and their range of mowers might not quite be the household name that it should. However, along with their sibling STIHL, VIKING are well known amongst gardening professionals and enthusiasts.

I was honoured to be asked to attend the very first press-day at the VIKING HQ. Especially being the only tech/gadget blogger on the trip.

This was no doubt to get the brand a bit more visibility. What it also showed me was the amount of pride that everyone at VIKING puts in to what they produce. The head quarters not only houses the offices, but the research and development labs, design team and factory. All under one roof.

VIKING – a quick history

Not only am I going to keep this brief but the company isn’t really that old either.

In 1981 the company started making shredders and then, in 84, their first mower was produced.

Jump to 1992 and this is when VIKING joined the STIHL group.

Then, in 2001 VIKING opened its new Competence Centre. This was necessary to accommodate the company’s Rapid growth. The new state-of-the-art facility is just 4km from the original site and houses production, marketing, sales and administration. It also has this (above) as a view from its factory floor!

VIKING cleverly bought a plot large enough to cater for expansion. Phase II happened in 2007.

Up to present day now. The motto for the VIKING brand is “Love your lawn”.

VIKING is a premium brand that designs, develops, manufactures and sells an expansive range of lawn mowers, lawn tractors, scarifiers, garden shredders and tillers.

Consistent development of high-quality products, a powerful reputation and strong collaboration with the STIHL Group have made VIKING a leading company in the gardening power tool sector.

VIKING press day

Our rather small, yet select, Band of journalists were treated to some time with Peter Pretzsch, VIKING’s MD, Robin Lennie, MD of STIHL GB as well as a number of the VIKING staff.

As well as formal presentations and QA sessions, we were given a tour of the facility.

Now, visiting a lawn-mower factory might not sound that interesting to most people. I will admit, I wasn’t sure how much I would get out of this trip either. I am glad I went though.

The main thing that hit me was the amount of research and development goes in to every part of what VIKING produces. The latest mower blade is a prime example. Something like 2 years has gone in to this part alone. Not only to improve cutting but damage limitation. You see, when a metal blade strikes a large rock or similar, that force is usually transferred up the driveshaft. This is costly to repair and you could be looking at a new engine and therefore a new mower.

What VIKING has done is build in crumple zones to the blade which will deform and save the shaft.

All very clever. But, while they were doing that, they also looked how they could make mowing quieter.

I had no idea that I would be visiting Europe’s largest anechoic chamber at a mower manufacturer! This is the level that this company goes to in order to ensure what comes out of its doors is top quality gear.

What impressed me was that the assembly was all done by hand. Not only that, the workers on the line actually appeared happy, as well as proud to show us what they were doing. As I said, this goes from the shop-floor all the way to the head honchos. That has to make a difference.

New VIKING mowers

As well as taking us around their operation, the company also had some new kit to show off.

Naturally, being GadgetyNews, the robot mowers from the iMow series caught my eye first.

iMow Series 4

The Mi 422 and Mi 422 P are specially designed to suit small and medium sized gardens, changing the way home-owners think about lawn care.

Both models feature simple intuitive programming via a NLCD display. This allows you to set up an automatic mowing-plan calculation based on your garden.

The clever tech can also be set up to avoid obstacles such as patios, trees and sheds. While the Mi 422 will mow lawns of up to 500m 2. the Mi 422 P will take on gardens of up to 1,000m 2.

What’s more, with adaptive slope speed, both mowers can master even hilly terrain; with the new Mi 422 P performing on an incline of up to 40%.

They boast variable cutting height adjustment and, like all of the VIKING iMow models, features mulching blades so they fertilise the lawn naturally for lush, well-nourished lawns, without the need to dispose of clippings.

Weather is no issue for iMow. Thanks to a sensor, it automatically reacts to rain. So, whether it has to run for cover because of a downpour or dock because you’ve cancelled today’s mow, it will intuitively make up the lost time another day.

iMow Mi 632 PC

It wouldn’t be a robot mower range without an app-enabled version.

The Smart and intuitive technology allows you to control the iMow’s mowing operation from wherever you are via an Android, iOS or Windows mobile app.

As well as sending your obedient Mi 632 PC out to mow, the app allows you to easily send it back to its docking station, with no need to be there.

A GPS module fitted in the mower means your app will know where your iMow is at all times. You can also change the mowing plan easily from the app, amending the times you would like iMow to go out to suit your lifestyle.

What’s more, the Mi 632 PC will give you helpful feedback via the app if it runs into any problems such as needing the blade replaced or requiring a service.

You, of course, still get variable cutting height adjustment and a robust mowing blade which is sharpened on both edges – cleverly alternating the direction of rotation to prevent wearing on one side.

Just like the 4 Series, you can programme it via a NLCD display. So you can set it up to avoid obstacles such as patios, trees, sheds and swimming pools. What’s more, with adaptive slope speed it can master even hilly terrain of up to a 45% gradient. The Mi 632 PC efficiently mows lawns of up to 4,000m 2 in just a few hours per week.

MA 235

New for 2017, the Compact Cordless System VIKING MA 235 gives homeowners a battery-powered mower that offers maximum flexibility for small to medium sized gardens up to 200m 2.

This small, quiet mower is perfect for lawns and gardens with tight corners and obstacles to mow around, when a cable might get in the way.

Intelligent design

The powerful long-life battery works with an impressively efficient electric drive system. This forward-thinking feature allows the user to mow for longer on a single battery charge.

Further efficiency gains are achieved through eco-mode. This adapts the speed of the motor to suit the grass it is cutting. The motor therefore only uses as much energy as it needs at any given time.

Comfort features

In addition to all of its technical advantages, the mower is also extremely easy to use. At just 14kg, the machine is lightweight and manoeuvrable. This makes it ideal for mowing in tight areas. Add in the height adjustable ergonomically designed handlebar, it should be a pleasure to use.

The robust 30L capacity grass catcher box has a clearly visible level indicator to show when it is full. What’s more, large recessed grips and an extra-wide aperture in the lid help with handling when emptying.

A feature of all VIKING mowers is the central cutting height adjustment. This can be smoothly adjusted in five settings between 25mm and 65mm.

The MA 235 combines VIKING premium quality and comfort, material and function, with advanced battery technology from STIHL.

MA 339

The VIKING MA 339 C battery-powered lawn mower is the perfect partner for maintaining lawns, as Lithium-Ion technology revolutionises lawn care for both professional and home users.

Comfort control

The Compact Cordless MA 339 C weighs just 14kg with a cutting width of 37cm. This makes it ideal for smaller gardens where manoeuvrability is key.

The cordless nature of the mower makes light work of lawn care as there is no dependence on a power supply – allowing for greater mobility.

The mower’s convenient mono handlebar provides the gardener with extensive freedom of movement with easy access to the grass catcher box.

The mower’s handlebar is adjustable to ensure a comfortable experience for any user. This feature is combined with a sturdy die-cast aluminium console, which ensures even force application and minimises the strain on your back.

Compact capacity

Whilst the mower may be compact in size it can still carry up to 40L of clippings which is perfect for a medium to large size garden. The grass catcher box can be easily emptied thanks to the large carrying handle and a hinged cover.

Those wishing to mulch their grass clippings can convert the mowing deck quickly and easily using the kit available from VIKING’s accessory range, which comprises a multi-blade and mulching key.

Innovative technology

The cordless lawnmower is powered by a low-noise, 600W motor. This technology was developed by parent company STIHL.

Owners of cordless, battery-powered STIHL Compact Cordless System tools can use the same battery in this VIKING mower too.

VIKING Mowers – time to cut and run

I’ve always tried to buy the best of what I can afford. Until recently, I was pretty much unaware of either STIHL or VIKING. This is probably due to them not featuring in DIY stores. After using STIHL products and seeing the effort that goes in to the VIKING range, I have a feeling that my aged Flymo will soon be kicked in to touch.

With that in mind, I hope that I can bring you reviews of the Compact Cordless mowers when it’s cutting season

Price and availability

Like all STIHL and VIKING products, you cannot just grab one at Homebase. Such is the customer service from these companies, you have to pick them up at a specialist service dealer.

Some offer an option to buy online for home delivery or click and collect. The thing is, when you do pick up your new VIKING or STIHL product, the people there will assemble it and talk you through how to use it. That’s all part of the service.

MA 235 – RRP £249.00 (machine only) or £369.00 (with battery and charger)

iMow prices

Mi 422 has a RRP of £999, the 422 P – £1,199 and the 632 PC £2,299

Riding Lawn Mower Blades Won’t Engage — How to Fix, Causes, and

If you buy something through our posts, we may get a small commission. Read more here.

It can be frustrating when your riding lawn mower blades won’t engage after powering it on. This won’t only make your day’s work difficult but ruin your other engagements and turn your work session into repair. Several factors can cause your lawn mower’s blades not to turn on. But how can you fix this issue? Our professional team has come up with solutions to try.

Riding Lawn Mower Blades Won’t Engage

Taking care of the lawn is made easy with a riding lawnmower. Like every other machine, you don’t expect it not to develop faults. From the belt to the battery, things can cause the riding lawn mower blades not to engage even when the mower blades are fully sharpened. When these problems arise, our technical expert advises that you should do the following.

Refer to Manual from Manufacturer

One of the first things to do when you discover that your mower’s blades won’t engage is to refer to the manufacturer’s manual. Lawnmowers differ from manufacturer to manufacturers, so as their manuals. You won’t expect a Craftsman mower manual to be exactly the same with Husqvarna, Cub Cadet, or Ryobi. For this reason, you must refer to the manual whenever the blades won’t turn or if you notice any fault.

Inspect Belt

One of the reasons why the blades on your newly purchased Troy Bilt lawnmower may not engage is the belt. It’s either stretched or too loose, worn-out, or damaged, causing it to fall off easily. It could also snap out of position, especially if you tried to cut more grasses at a time that’s beyond its capacity.

The deck belt, located under the operator’s seat, works by engaging and disengaging the mower’s blade. The belt runs through a pulley system and spins the blades. If it has become damaged, the blades won’t engage.

Before carrying out any replacement, you should inspect the belt first in case your Cub Cadet mower has belt that keeps coming off. The configuration depends on the model and manufacturer, but most lawn mowers have the same design. Reduce the deck to its lowest setting and check out if it’s damaged or has accumulated grasses.

The belt must be inspected at least every six months. This way, you won’t be surprised and frustrated when you want to take care of the lawn.

Replace Belt, Cables, or Clutches

If you notice any damage or excessive wear on the belt during the inspection, it is advisable to address the issue by replacing it. Similarly, if the belt appears loose or excessively stretched, it is recommended to return it to ensure optimal performance.

If the blades don’t still work even after replacing the belt, you should check the blade cable. The cable is made up of metal with cast metal ends, a plastic sheath, and a bracket. If the metal ends are damaged or the cable gets kinked, you should replace it immediately.

You can do the same to the clutches if you find any of the parts damaged. Lawnmowers have clutches that shut off the blades while the engine is running. This part can wear out over time, and when they do, they won’t be able to power the blades.

It’s necessary that you inspect them for proper diagnosis. Disassemble the mower to monitor the clutch better.

If any of the parts that make up the clutches develops a fault, the blades won’t engage. It means you should replace them.

Check Pulley

The pulley could be another reason why the riding lawn mower is having issues causing the blades not to engage. The mower’s pulley controls the tension in the drive belt, which in turn turns the blades. If the pulley freezes and doesn’t rotate, the blades won’t engage.

This is why you need to check the pulley to know its state. If it’s frozen, then you should replace it. You should also investigate if other pulleys on the deck are okay [1].

Check Power Source/ Battery

Lawnmowers use the PTO (Power Takeoff) clutch mechanism to engage the blades. PTOs are either manually operated or electric. Batteries run the electric PTOs.

If the battery has a weak charge or is dead, it won’t power the blades. So, if the blades refuse to engage after powering it on, ensure that you check the battery. You must fully charge the lawn mower battery, and if it’s faulty, you should replace it with a new one.

Tips and Reminders

Here are some tips and reminders you must have at the back of your mind when engaging the mower blades.

• Check if the deck belt is installed properly.
• Make sure that you charge the battery fully if the mower blades are electrically powered.
• Ensure the deck is lowered to the desired height before starting it.
• Allow the engine to warm up for a few minutes before using it. Replace all damaged belts, cables, and clutches after inspection.

Why won’t my riding mower blades engage?

Even if you have a reverse threaded mower blade, your riding mower blades won’t still engage if the clutches are broken and the cable is damaged. Additionally, if the deck belt is damaged, the pulley system is frozen, and the battery has a weak charge, the chances are that your riding mower blades won’t engage.

How do you engage the blades on a riding lawn mower?

To engage the blades on a riding lawn mower that’s manually operated, turn the key clockwise to power it on, increase the throttle to half speed, and allow the engine to warm up for two minutes.

Then, lower the mower to the preferred cutting height. Push the lever to the right of the steering to engage the blades.

It’s the same if you want to engage a lawnmower with electric blades, except that you don’t have to push the lever to the right of the steering to engage the blades. Just pull up on the yellow Power Takeoff switch to the right of steering.

Conclusion

Lawnmower blades are liable to damages, so it’s typical for them to have issues. However, the level of damages depends on how often you use the mower. This is why carrying out periodic inspections is necessary to prevent escalating the damages. With these practical solutions explained, you can fix the issue that arises.

If you are unable to fix them, contact a professional or if warranty still covers your lawnmower, contact the brand’s customer service. Some manufacturers that have good customer support include Husqvarna, Craftsman, Cub Cadet. and John Deere.