Why is a gas cocked and stalls.

23rd November 2022

Why stalls a lawn mower or a lawn mower when pressing for gas, opening an air damper or at high speeds

The maximum and minimum engine speeds, even idle is regulated by the carburetor. The stable operation of the lawn mower depends on the amount of fuel mixture and air. The lawn mower is not started with disturbed adjustment of the carburetor. The procedure for setting up the device for supplying fuel at low speeds (L), high speeds (H) and idle (T) is regulated by the same vints:

The chainsaw should work for at least 10 minutes, since the adjustment is carried out in hot.
The screw n is flooded smoothly to maximum speed, then turning on ¼, counterclockwise, reducing the speed of rotation of the engine shaft.
The idle stroke is regulated by the screw T, ensuring that the braid for the grass does not rotate.
The screw l is regulated, first opening the throttle as much as possible, and then smoothly reducing the speed to stable minimum.

After adjustment, a proper carburetor with cleaned filters should ensure the operation of the engine. In the event of a malfunction of the carburetor, after its repair, it will again need to configure the supply system before starting the lawn mower.

Rare breakdowns that prevent the operation of the lawn mower can be:

Well, even if after such bullying your trimmer does not start for the grass, you can’t do without disassembling the carburetor. It may very well be that everything is to blame for the gathering of the needle in it. It stalls in idle. Когда нагреется ее триммер для травы сразу глохнет почему глохнет. Why is hot stalling ? Actually, if you take a hot one for a hot trimmer for grass? Hitachi. In any case, the disassembly and washing of this capricious mechanism certainly will not hurt.

In general, when a trimmer for the grass began to be capricious and stall, it is advisable to carry out complete prevention: to completely change the fuel mixture, try another oil, and also mandatory change the candle. Practice shows that in many cases, it is precisely cheap low.quality candles that are to blame.

We examined the most typical reasons why a trimmer is not started for grass. If the matter is something more “exotic”, do not pass the campaign in the service center. You will probably find smaller and obvious breakdowns yourself.

Not starting a chainsaw on hot

There are no unnecessary phrases in the operating instructions, everything that is proposed is aimed at the trouble.free operation of the lawn mower. Cleaning all parts after each cycle of work contributes to the light removal of not hardened residues and dirt. You need to clean only cooled nodes. This technique contributes to the quality of the air cooling of the engine and the gearbox.

For refueling, it is necessary to use fuel with oil recommended in the instructions. If you leave the combustible mixture in the fuel tank, the oil will float and dies on the damper when starting, worsening its adjustment. The mixture can give a sediment and score fuel supply in the carburetor.

When preserving equipment for the winter, make an audit, grease the gearbox and the piston system, wrap the entire saw in the oiled rags and store in a dry place.

It is impossible, dangerous for the instrument and health of the mowing, use a metal cable instead of fishing line. It cuts more efficiently, but the load on the gearbox and the engine increases. A demolished piece of wire when separating flies at the speed of a bullet. Effective mowing can lead to a speedy wear of the piston group of the engine. For greater efficiency of the mowing, it is proposed to use the profile of the “Star” fishing line.

It is impossible, dangerous for the instrument and health of the mowing, use a metal cable instead of fishing line. It cuts more efficiently, but the load on the gearbox and the engine increases. A demolished piece of wire when separating flies at the speed of a bullet. Why is it hot bad if the motor is poorly started on why a trimmer does not start for grass.

What could break

Malfunctions with a benzocosa associated with the fact that this device is not started, in a certain way are classified by specialists of service services. They stand out malfunctions with the following nodes of the mechanism:

the engine in which the piston and bearings can be worn out or fail to crack the crankcase;
the fuel supply system, while it is possible to clog the filter or problems with the carburetor;
mechanical damage to wires, tubes, hoses;
The ignition chain.

To correctly determine the knot where the breakdown occurred, it is necessary to pay attention to the circumstances of the trimmer stalls for the grass.

Ways to eliminate breakdowns

Subsequent work is likely on the carburetor:

cleaning and adjustment of the fuel supply valve;
similar work with a valve producing redesigned gases and pairs (after burning fuel);
replacement of the spring more weak on the entrance valve;
restoration of the tension of the carburetor cable;
replacement of the fuel leaks hose, verification and strengthening of a weakened connection;
changing the rotor damper disk;.
Change of faulty wire or ignition coil.

Immediately after the start

Smelting Motokos or a trimmer for the grass after starting is justified by subsequent reasons:

impressive of previously adjusted valves;
first the wrong settings of the valve mechanism;
clogging with deposits of the fuel supply valve;
the hose is worn or poorly annexed.

Due to the violated method of injection of a fuel, a lawn mower or a trimmer for grass is very vibrated in work.

Asseting device and common malfunctions

The easiest way to give the lawn mower for repairs, allocating a certain amount of funds from the family budget, operational and high.quality repair with your own hands is no less simple and convenient to understand the design of the lawn mower and fix all the problems.

The massive and piece manufacture of trimmers is based on the use of generally accepted technology, the typical design scheme consists of certain elements and parts, it is important to know them when carrying out independent repair work:

top part. The basis of the entire structure, where all important elements are collected, such as the starter, carburetor and the engine of the lawn mower;
middle part. Hollow rod, inside it is a cable connecting the engine and gearbox, which sets the cutting fishing line for the trimmer. In this part there are mounts for the distribution of weight of the entire structure and a belt for fixing a trimmer for grass on a belt of a person using a trimmer for grass for its intended purpose;
Bottom part. It has a gearbox and cutting elements that are hidden under a practical casing, which protects the user. The casing provides an increased level of safety, preventing large fractions of garbage, pebbles and glass in a person while working with a gas station.

The most common and often encountered, subject to independent correction of the breakdown of the unit can be called the following problems:

engine malfunction, due to which the lawn mower is not started and does not work;
enhanced vibration of the bar motorcosa, which complicates its targeted use;
increased overheating of the gearbox, its accelerated heating during operation;
slow and weak functioning of the cutting fishing line at insufficient speeds;
the clogging of the starter grill causing the engine overheating and its refusal to work;
rapid and frequent clogging of the carburetor due to the use of poor.quality fuel;
clogging of the air filter in case of non.compliance with measures to care for the device.

All these problems can lead to the fact that the device will lose its ability to work before ordering the necessary spare parts for non.bosomeds should be carried out by a visual inspection and diagnosis of the device.

Special attention is required by individual spare parts and assemblies of the device, to verify them, you will not have to turn to a professional master, a complex of diagnostic measures will help to identify a consequence of the occurrence of a loss of performance.

The lawn mower stalls

When purchasing a lawn mower, you need to be prepared for the fact that, as in all other similar tools, it may also have breakdowns that will require repairs.

However, do not immediately run to the service center and pay a lot of money to the masters who convince you of a serious malfunction in the device.

The lawn mower stalls at high speeds

Perhaps the most common complaint related to gasoline trimmers sounds like this: “The lawn mower stalls“.

Of course, the reason for this may be a rather serious malfunction. However, most often the situation is much simpler than it seems at first glance.

To cope with such a problem, first of all, try to deal with its causes on your own, because, having found out the reason, it is much easier to fight the problem, and sometimes it is even self.destructive.

In fact, the reasons are when the lawn mower stalls at high speeds, there are quite a lot of these reasons.

Another, this is the presence of malfunctions in the power system.

In this case, the lawn mower will stall at idle. The problems with the power system may lead to a drainage or incorrect carburetor adjustment.

Vibrations that take place in the process of operation of the lawn mower can lead to a reservoir.

Incorrect adjustment of the lawn mower can be fixed by simply adjusting it in accordance with the requirements specified in the operating instructions.

In addition, sometimes gasoline trimmers for grass can stall due to the fact that the valve located in the gas tank lid just clogged or sticks.

To find out, try using a braid by loosening the gas tank cover.

If in this mode the device works properly, clean the valve.

over, the lawn mower can stall due to poor fuel flow into the carburetor

Why then the device starts up, ask you?

The reason for this is that at first the fuel gradually falls into the carburetor and is enough for work with increased power.

However, then it is produced and at large speeds the engine begins to stall.

As for the carburetor, here the problem may also be that its body is too pulled.

The reason that the lawn mower stalls at high gas speeds may also be an air leak.

We are talking about the possible presence of a place through which air can pass during the heating process of the engine.

Among other things, do not forget to check the fuel intake hose. The problem may be that it is weak or cracked at all.

These are the main reasons why the gas mowl can stall.

The gasoline trimmer for the grass starts and stalls

Why is a trimmer not starting for grass gasoline? Reasons and their elimination

Recently, a gasoline trimmer for grass has acquired the status of one of the main tools in the arsenal of summer residents. And this is not surprising, because a motorized braid for grass allows you to quickly put a personal plot in order. However, sometimes it happens that the trimmer for the grass does not start hot and even on cold. In such situations, you have to independently establish the cause of the malfunction. Let’s find out what to do if a trimmer does not start for grass. The reasons that most often lead to such troubles will be considered further.

Diagnostics strategy

Where to start the diagnosis of malfunctions if a trimmer is not started for grass? In situations where the tool stalls immediately after starting, it is worth examining the following units:

It is the breakdown of the above locations that most often leads to the fact that a trimmer for grass is poorly started. Let’s look at how to eliminate such troubles.

Checking the fuel mixture

Suppose you don’t start a trimmer for grass. In this case, the first thing is to check whether the fuel is enough in the tank, as well as evaluate the quality of the fuel mixture. To refuel a motorized unit, it is necessary exclusively high.quality gasoline. It is recommended to use fuel, the brand of which is not lower than AI-95. Refueling a trimmer for grass with fuel of unknown origin, not bought at a gas station, is fraught with frequent failures in the work of the tool. This can cause a breakdown of the cylinder-piston system. Repair in this case often exceeds the cost of the device itself.

Why is a trimmer not starting for grass gasoline? Incorrect preparation of the fuel mixture may also lead to this, which consists of oil and gasoline. The proportions in which the specified components are connected are indicated by manufacturers in the guide for the operation of a trimmer for grass. Preparing the fuel mixture is extremely not recommended in large volumes, that is, for the future. Indeed, with prolonged savings, there is a loss of the determining properties of the substance. Therefore, if a trimmer for grass does not start, it is worth draining the old fuel and use freshly prepared fuel mixture.

Read which trimmer for grass is better than rotary or vibration

Diagnosis of the candle channel

What to do if the used fuel mixture is in perfect order, but a trimmer for grass is still not started by gasoline? The reasons for the refusal of the mechanism may lie in excessive moisture of the candle channel. To diagnose and eliminate the problem, it is necessary to do the following:

To twist the candle. Wipe it thoroughly, and then dry it.
Drain excess fuel in the chamber through the corresponding candle hole.
Clear the old candle if there is a dozen on its surface. Cope with the task will allow the use of a conventional ladies’ nail file or file.
When installing the element in place, set a gap of 1 mm. To check the parameter, it is enough to place any coin in the lumen.
Collect a functional block back.
Try to start a trimmer for grass.

It is recommended to perform a candle channel to dry for at least half an hour. However, in no case should you resort to the calcination of its elements. After all, heating the spark plug can lead to its final corruption. Что предпринять, если обслуживание функционального блока было выполнено в соответствии вышеуказанным рекомендациям, но триммер для травы не заводится, искра есть при этом? In this case, it should be treated with gasoline threaded connection. The latter does not need to be saturated abundantly fuel. It should only be slightly moisturized. Resort to such actions should be to ensure the ignition. After all, no matter how much the candle gives a strong spark, in an absolutely dry chamber there simply will not be something to ignite.

The lawn mower stalls

Carburetor adjustment, well start

,stalling when pressing gas. My Skype: Ork.Vitek tel. 380979677418

The lawn mower stalls or suffocates when you press the gas

Even more information about the repair and choice of tools on our website www.Looktool.Ru, we are happy for everyone.

If even in this case a trimmer for grass does not start, it is worth evaluating the quality of the contact between the high.voltage wire and the candle. In the absence of a spark (in the presence of a reliable connection between the indicated elements), most likely, the problem is caused by breakdown of the ignition unit. In this situation, you will have to turn to the services of masters who will reinstall the knot.

Checking filters

Another common cause, due to which a trimmer for grass does not start, is the presence of a blockage in the filter area. To confirm the conjecture, just dismantle the indicated block and try to start the unit without it. If the engine of the trimmer for the grass has launched, most likely you will have to replace the air filter or at least perform a thorough purge of the old. In the presence of abundant contaminants on the surface of the filter element, it is necessary to use a new grid. Relying to such actions, you should not leave a suction pipe at all without a filter. After all, rush in this case can lead to the need to repair the entire piston group of the unit engine.

Cleaning the soundtress

Often the engine of branded models of trimmers stalls as a result of clogging of the soundtress. The main task of the specified component is to align the pressure in the fuel tank. In the case of contamination of the node, a vacuum is formed here, which significantly complicates the supply of fuel. Eliminating the malfunction allows the cleaning of the saapon using a conventional sewing needle.

Diagnosis of the graduation channel

The stable functioning of a trimmer for grass can be impaired as a result of laying dirt in the graduation canal or the formation of a blockage on a muffler grid. This problem most often occurs during the operation of older generation trimmers. The issue is being solved by dismantling the anti.diploma mesh and its cleaning.

How to prevent sudden breakdowns during the operation of a trimmer for grass?

So that the unit is always in a functional state, it is worth observing several simple rules:

Preventive measures and operating rules

So that the lawn mower does not work and does not stall when starting, it must be correctly stored and operated. Compliance with the following simple recommendations will forget about problems.

When begging the grass, you need to monitor the state of the cooling system. It is also necessary to regularly clean the channels in the case and starter’s ribs.
To clean the tool, you should use kerosene, solvent, or other washing tools.
You can not clean a hot tool. it must cool before washing.
It is important to observe the recommended working mode. this will avoid overheating of the engine.

To store the tool in cold weather, you need:

completely drain the fuel;
disassemble the lawn mower, wash and clean all available components;

inspect the condition of the parts, eliminate all defects that can be corrected;
pour the required amount of oil into the gearbox;
Clean the air filter;
perform partial disassembly of the engine, wash all moving parts, blow and lubricate thoroughly;
To lubricate the piston, unscrew the candle, then raise the piston to the upper dead point by the starter, pour a small amount of oil into the hole for the candle and do the crankshaft several times.

Important! If there is no way to store a trimmer for grass in a warm dry room, you must first wrap the motor with an embarrassed rag.

Only by observing these rules, you can be sure that the lawn mower will work properly and will not stall for a number of seasons.

As you can see, stopping the work of a trimmer for grass can be caused by many reasons. Most of them can be fixed independently using the user instructions. In cases where there is no self.confidence, the equipment is recommended to be attributed to repairs. It is worth remembering that incorrect actions can cause even greater harm to the trimmer. As a result, the repair of Motokos will cost a much larger amount than it would be initially, and in the worst case, it may be necessary to buy a new unit.

Why is the lawn mower stall at idle

Why does the lawn mower stall when you press the gas: the prerequisites and their solutions. The lawn mower stalls (trimmer for grass):. On idle

Users have repeatedly ask about stopping the braids for the grass “on hot”, that is, when the mechanism started, worked a little, and then took it. and stopped, stalled. The reasons for this situation are the following:

problems with the carburetor damper;
Gasoline in a carbe can even boil;
If the ignition is damaged, then the trimmer for the grass will also heat up and stall.

In each of the situations, check the details for strength, and if they have already outlined their own, order new ones from specialists. We will call one of the most popular situations: the lawn mower stalls at idle. This happens for reasons:

The carburetor was diluted himself, or was illiterately adjusted;
the carburetor is contaminated;
The air filter is very contaminated;
The use of inappropriate fuel can cause a reduction in the gearbox revolutions;
At idle, your trimmer for grass can stall if the throttle closed;
Air fell into the carba system;
The lawn mower receives a missing portion of gasoline to work fully, and therefore stalls.

We are sure that you received the maximum of useful information, and found a way out of your individual situation through our technical councils. Any spare parts, like a starter, motorcycles, its components and accessories are located at the lowest value in the country. Hurry up!

Often, when reducing the speed, the motor motorcycles stalls and does not support idle speed when re.starting. The main reasons for the occurrence of such a breakdown include pollution or the dumping of the carburetor, as well as clogging of the air filter.

In case of violation of the optimal settings of the carburetor, it is necessary to clean it and repeated adjustment. You can cope with clogging the air filter of a trimmer for grass by placing it for several hours in a solution with a conventional domestic detergent. If independent cleaning has not helped to cope with the blockage, it is better to purchase a new filter element in accordance with the operating manual.

After the measures, the user will not encounter a situation for a long time when a trimmer for grass stalls in idle and functions only when gas supplies.

A braid braid with a gasoline drive is a useful thing for owners of personal plots, lawns, and when a trimmer for grass suddenly stalls, the work on cleaning the territory stops from the grass. The device itself is a rather complex mechanism, so there are many different causes of its breakdowns.

reducing the speed of the gearbox when heating it, which is a consequence of the use of inappropriate fuel mixture;
clogging of the throttle;

air entering the system;
not enough fuel for the operation of the lawn mower.

If a carburetor is a problem place, then the technique will stop at the “cold” and with a “hot” launch.

At idle

At single speeds, the common reasons for stopping a trimmer for grass are as follows:

We Defibrillated a Steak

reducing the speed of the gearbox when heating it, which is a consequence of the use of inappropriate fuel mixture;
clogging of the throttle;

air entering the system;
not enough fuel for the operation of the lawn mower.

Immediately after the start

The stalling of motorcycles or a trimmer for the grass immediately is due to the following reasons:

impressive of previously adjusted valves;
Initially incorrect setting of the valve mechanism;
clogging with fuel supply valve;
the hose is worn or poorly attached.

Due to the violated algorithm of fuel injection, the lawn mower is or is vibrated in the work.

When pressing gas

If the lawn mower stops when pressing the gas, then the prerequisites may be subsequent.

The more increased option is a carburetor adjustment failure that appears with significant load loads after a long.term inaction of the mechanism or when using it in languid criteria.

If the problem is associated with the carburetor node, then it can be recognized by the appearance of vibrations of the lawn mower. Когда лопается шланг или растягивается трос — выполняют замену данных комплектующих.

At high speeds

When a braid for grass stalls at high speeds, this is due to the following problems:

clogging or clutching a valve located on the gas tank lid;
The carburetor was diluted under the influence of vibrations arising during the operation of the mechanism;
Circulation problems fuel mixture;
atmospheric air
The hose intended for fuel fuel cracked or slightly connected.

The carburetor is regulated by relying on the operational instruction to the trimmer. For configuration, it is often enough to weaken the tightening of its body. If there are problematic issues with the circulation of the fuel mixture, then it can gradually enter the carburetor. After its production, the engine stalls at high speeds.

Why is a haircut machine heated? What to do with it?

The haircut machine is very hot when working? It is unpleasant. Here we will figure out possible reasons. and explain what to do in these cases.

Why should the machines be avoided completely?
Why the machine begins to heat up hard during operation?
What the heating of the machine from the very beginning depends on what?

Why should the machines be avoided completely?

What kind of elegant and accurate your machine would not be, do not forget. inside it is an electric motor. And, if you have a good machine, this motor is quite powerful. For example, Mustang haircut machines give out 5,900 revolutions per minute. That is, approximately 98 revolutions per second! Yes, yes, this is the time that you need to say “once”.

Knives move at an incredible speed. Naturally, they heat up. even with good lubrication, the friction force still remains. And the engine itself, which issues such power, is heated. This cannot be avoided other than turning off the machine.

But. This does not mean that the machine in your hands has the right to turn into an included iron. The design of the machine should be such that the release heat is distributed and does not cause discomfort during operation. And if the machine begins to bask indecent, then either the design was initially not reasonable enough, or something happened to the machine.

Why the machine begins to heat up hard during operation?

The reason number one, which accounts for most situations when the initially working machine begins to overheat. pollution. Cutting hair, settled by skin fat, dust. all this increases friction when knives move. Accordingly, the system heats up harder.

Thus, the first thing to do if the machine begins to bask is to clean it. The matter is thin, but quite real. We wrote a separate article about this, we will not be repeated better.

So, the machine needs to be cleaned, lubricated, and then look. and if nothing has changed, carry it to the service and ask the master what could happen to it.

This, of course, concerns cases when the machine was originally working normally and did not particularly warm-and then suddenly began to heat up somehow suspiciously. Because many cars begin to bask from the very beginning. fierce and inconvenient. What to do with such cars?

Liquifying Suicide Bombers in Baghdad | Ultimate Warfare

What the heating of the machine from the very beginning depends on what?

What can be done with a machine that begins to warm powerfully from the very beginning, even despite the fact that it is quite clean and lubricated? Well, there are two options. either to suffer and endure, or throw and buy a normal.

Because the heating of the machine depends on the rationality of its design and the quality of the selected motor. And if one of this is originally done incorrectly, then the machine can only be redone.

In Mustang, we pay great attention to both the design and the motor, because we believe that the hairdresser should serve for a long time and without complaints like excessive heating. It’s nice to know that our tools are proud and boasted

The gasoline trimmer for grass stalls at idle

Often, when reducing the speed, the motor motorcycles stalls and does not support idle speed when re.starting. The main reasons for the occurrence of such a breakdown include pollution or the dumping of the carburetor, as well as clogging of the air filter.

Gasoline trimmer for grass stalls at idle

After the measures, the user will not encounter a situation for a long time when a trimmer for grass stalls in idle and functions only when gas supplies.

The trimmer for grass stalls. how to eliminate the problem

A gasoline trimmer for grass is a useful tool for cleaning from unnecessary grass of house territories and large area lawns. The design of this technique is quite complicated, therefore, if the device breaks, there may be several reasons. The most likely factors that have caught a breakdown are usually described in the user guide. Knowing why a trimmer for grass stalls, you can try to independently eliminate the defect. The most common malfunctions provoking the motorcycle stops, and the ability to repair them with your own hands is in the material further.

In order to most accurately determine the cause of the trimmer malfunction for grass of any brand (for example, echo) and find out the possibility of eliminating it, you need to install, when performing what action the device stalls. The engine can turn off both at idle and at high speeds, heated under load or immediately after starting and t.D.

If you stalled after gas supply

Owners of gasoline braids often mention that the lawn mower stalls when you press the gas. Usually such a breakdown occurs due to problems in the carburetor. A failure in his work can occur due to long-term storage, use in difficult conditions, significant overload of the motor. The symptom of such a breakdown will be vibrating movements of the device during operation.

On a note! Users familiar with the repair of a car carburetor can try to restore this important node of the trimmer for the grass on their own, using the instructions for operating. Otherwise, the correct decision will be to seek help from the service center representatives.

Sometimes a trimmer for grass stalls when you give gas because the fuel valve is clogged. This interferes with the supply of gasoline. To eliminate the problem, it is enough to loosen the valve. Thus, normal supply of carburetor fuel will be restored.

Another possible reason why the lawn mower stalls when gas is supplied is pollution of the soundtress (check valve). This detail prevents the appearance of a vacuum in a gas tank. If it is clogged, the air does not flow, which means that fuel does not go to the carburetor. To eliminate the problem, it is necessary to clean this element.

If it stalled at high speeds

If the carburetor stalls at high speeds, this means that in idle and small there are enough incoming fuel, and to work on high is not enough. Then it is necessary to check the serviceability of the following nodes of the trimmer for the grass.

Fuel hose. its integrity could be violated as a result of cracking. In this case, you need to replace the part. Or maybe you just need to tighten the clamps.
A filter network between a carburetor and a hose for supplying a gasoline mixture-it could clog. In this situation, it is necessary to clean the detail.
The valve on the gas tank cover. he could stick or clog with garbage. Cleaning is also necessary.
Carburetor. perhaps as a result of constant vibration, it was resolved. This is usually characteristic of cheap Chinese details. To eliminate the problem, it is necessary to set up according to the instructions. In some cases, it is enough to only weaken the tightening of the carburetor case. If the adjustment is not possible, it is necessary to install a new element.
Additionally, check the air filter. Perhaps it will need to be washed and cleaned or replaced with a new one, as he could clog with dirt and particles of grass when tilted technology, when the user mowed in hard.to.reach places.

If you stalled during work idle

If the lawn mower stalls, working idle, there may be several factors reasons.

First you need to check the prepared fuel solution, when it comes to a four-stroke trimmer working on a gasoline-oil mixture. There is a chance that it is made incorrectly. the proportions are not withstanded. Because of this, the gearbox is warming up, and the revolutions on the drum are lowering.
Another probable cause is blockage of elements such as a throttle, air filter or carburetor. You need to clean the indicated details.
Another possible factor is to resolve or incorrectly carried out carburetor adjustment. You need to adjust the setting according to the instructions.
Observe this problem mono and when opening the air damper. In this situation, the lack of fuel for a trimmer for grass occurs through the fault of the air flow.

If the device does not have enough fuel, it works properly at high speeds or when they increase, but stalls at idle. If the root of the problem consists in the carburetor, the lawn mower will be disconnected both with cold startup and hot.

If you stalled after starting

If the technique starts and stalls immediately after starting, this indicates the wrong settings or deducting the device. As a result of this, the fuel enters the engine unevenly, which leads to significant vibration and disconnecting the trimmer for the grass. To fix the breakdown, it is necessary to reconfigure the device according to the user management.

Another probable problem is the blockage of the valve supplying the gasoline mixture. It must be cleaned.

On a note! If the trimmer for the grass starts, but immediately stalls, it may also mean that the fuel is moving to the carburetor with difficulty. Weakening the valve will help to eliminate the problem. this will provide uniform and free circulation of fuel in the device.

Another possible reason is the damaged fuel intake hose. Air can penetrate through cracks and holes into the system. To solve the problem, you need to increase the engine speed in order to get rid of air bubbles that have penetrated the device.

If you stalled when opening the damper

If the technique works properly at idle, but stalls when opening an air damper, this reports about the penetration of air into the system through cracks in the fuel supply hose or damaged oil seals. To fix the breakdown and establish the work of the tool without driving air from the atmosphere, it is necessary to replace damaged parts.

Preventive measures and operating rules

So that the lawn mower does not work and does not stall when starting, it must be correctly stored and operated. Compliance with the following simple recommendations will forget about problems.

When begging the grass, you need to monitor the state of the cooling system. It is also necessary to regularly clean the channels in the case and starter’s ribs.
To clean the tool, you should use kerosene, solvent, or other washing tools.
You can not clean a hot tool. it must cool before washing.
It is important to observe the recommended working mode. this will avoid overheating of the engine.
If a braid for grass is not used over the next thirty days, the fuel must be drained, otherwise it will fall into heavy components that can score the channels of the carburetor.
After the fuel is merged, the trimmer for the grass should work at idle for some time until it turns off. This will allow you to completely get rid of the rest inside the working mixture.

To store the tool in cold weather, you need:

completely drain the fuel;
disassemble the lawn mower, wash and clean all available components;

inspect the condition of the parts, eliminate all defects that can be corrected;
pour the required amount of oil into the gearbox;
Clean the air filter;
perform partial disassembly of the engine, wash all moving parts, blow and lubricate thoroughly;
To lubricate the piston, unscrew the candle, then raise the piston to the upper dead point by the starter, pour a small amount of oil into the hole for the candle and do the crankshaft several times.

Important! If there is no way to store a trimmer for grass in a warm dry room, you must first wrap the motor with an embarrassed rag.

Only by observing these rules, you can be sure that the lawn mower will work properly and will not stall for a number of seasons.

The lawn mower is heated

In many lawnmands, an electric engine is installed, which in certain situations can overheat with the subsequent disconnection.

Interpretation in the winding;
problems with the start.up capacitor (inconsistency of the container, failure);
long work (from above the recommended parameter);
bias of flanges during assembly, which creates an increased load on bearings;
incorrect connection (for example, confused basic and launch windings);
wear and damage to the brushes/bearings;
Numbering voltage problems.

Judging by the reviews on the network, the common reasons for overheating of the gas mowing electric motor are an interval circuit and work with the device in excess of the set time.

When opening an air damper

It happens that the unit stalls when opening an air damper, working normally at idle. This is due to the air leaks of the system caused by the presence Cracks of the fuel hose

or problems with seals. The carburetor dosing system can also work malfunctioning, while the lawn mower will stop after the opening of the damper.

All possible reasons that the lawn mower stalls, and the methods of eliminating them are contained in the next video

There are many reasons for stopping Motokos, but the most commonly occur in work related to its carburetor. They can arise in any case. The most problematic option is when there is a serious breakdown, and you will need to purchase new parts or change the lawn mower.

Sources:

https://fermerx.ru/vyraschivanie/zavoditsya-benzokosa-garyachuyu-glokhnet-nazhatii-remont-svoimi-rukami-video/
https://tehnostroiplus.ru/sad-ogorod/trimmer-glohnet.html
https://101benzopila.ru/benzokosa-glohnet-pri-nazatii-na-gaz/
https://ltruck-service.ru/elektro/trimmer-ne-razvivaet-oboroty-i-glohnet.html
https://101benzopila.ru/benzokosa-pri-nagreve-glohnet/
https://isoprofteh.ru/v-sadu/benzokosa-nagrevaetsya-i-glohnet.html
https://himpribor-reaktiv.ru/dvigatel/diesel_engine/greetsa-dvigatel-trimmera-pricina.html
https://hitech-online.ru/tehnika-dlya-sada/trimmer/glohnet.html
https://benzo-electro-instrument.ru/pocemu-greetsa-benzinovyj-trimmer/

Articles stalls