Grinding Wheel Dressing – Wheel Dresser Types & Specification. Diamond grinding wheel dresser

Grinding Wheel Dressing – Wheel Dresser Types Specification

Dressing may be broadly defined as any operation performed on a wheel face to change the nature of its cutting action.

Why Grinding Wheel Dressing Needed?

Dressing is necessary when the individual grain crystal in the wheel face become dulled and the rate of stock removal is constantly decreasing as the grinding operation is prolonged without dressing.

Dressing is also necessary when the abrasive crystals or bond pores become loaded with metal or foreign matter, since this loading seriously affects the grinding action of the wheel.

Grinding Wheel Dressing Tools ( Wheel Dressers)

1) Diamond Dressers

Diamonds for dressing and truing grinding wheels are of several types, each having different characteristics.

“Multi-point”-An arrangement of twelve small set in a single plane in such a way that all stones contact the grinding wheel face simultaneously.

“Multi-Edge”-Three diamonds set in a line one behind the other, parallels to the wheel face. This tool is applied to the grinding wheel at a “down angle” and when the stones are flattened on one side from use, the tool is turned over.

2) Star Dressers

The Huntington or star type dresser has pointed discs loosely mounted on a pin, with solid discs as separators.

This type is exclusively used for dressing coarse grit wheels for snagging and offhand grinding and also for dressing segmental surface grinding wheels. It is low cost but requires some little skill in operation.

The Huntington dresser is the most efficient tool from the point of view of removing metal filling in general and the abrasive wheel type dressers are next in efficiency.

3) Precision Steel Type

This is popular and frequently used in place of diamond dressers for commercial grinding on precision grinding machines.

4) Abrasive Stick Dressers

These are of two shapes – square for hand manipulation and round for magazine mounting. Magazine mounting sticks find use in forming wheels for profile grinding and for dressing and truing relatively thin wheels.

5) Abrasive Wheel Dressers

These consist of properly bonded silicon carbide wheels rotably mounted in a suitable holder with high grade bearings. They will, in many cases, entirely replace the diamond on both center and centre less types of cylindrical grinding.

Their use imparts a smooth, clean cutting face which leaves no dressing marks on the work. With a few exceptions, since coolants are not generally used with the abrasive wheel dresser.

Diamond Dressers Specification

Hindustan surface grinding Segment are a universal choice for all those customers for heavy, Rapid stock removal and production work. These Segments can easily handle tolerance operations and are generally preferred in such uses only.

FAQs about Dressing a Grinding Wheel

Dressing of a grinding wheel refers to the process of re-shaping the abrasive particles on the surface of the wheel to restore its cutting ability. This is done by using a “dressing tool” which is typically a separate tool or a device built into the grinding machine. Dressing can be done manually or automatically and it can be done on a regular basis to maintain the quality of the grinding wheel.

Dressing and truing are both processes used to maintain the quality and condition of a grinding wheel, but they are different in terms of their specific purpose and the methods used to accomplish it.Dressing refers to the process of reshaping the abrasive particles on the surface of the wheel to restore its cutting ability. This is done by using a dressing tool, which is typically a separate tool or a device built into the grinding machine. The dressing tool removes worn abrasive particles, revealing new sharp edges and creating a uniform surface on the wheel.

Truing, on the other hand, is the process of making sure that the wheel is running concentrically and true. This is accomplished by using a truing tool, which is also typically a separate tool or a device built into the grinding machine. Truing is done to correct any run-out or wobbling of the wheel, and it is done to ensure that the wheel is round, straight and that its running face is square to the wheel axis.

Dressing a grinding wheel involves the following steps:1- Secure the wheel in the grinding machine and turn on the machine.2- Hold the dressing tool (e.g. a diamond dresser) against the wheel, with the tip touching the surface of the wheel.3- Apply light pressure to the tool and move it across the wheel surface in a uniform manner.Continue this process until the desired shape or condition is achieved.4- Inspect the wheel for any remaining defects and repeat the process if necessary.5- Turn off the machine and carefully remove the wheel.

It’s important to note that the specific steps and tools used may vary depending on the type of grinding wheel and the machine being used. It’s always recommended to check the machine and wheel manufacturer’s instructions before attempting to dress a wheel.

Also, it’s very important to use the correct type of dressing tool, as using the wrong one may damage the wheel or cause safety hazards. And also, it’s very important to wear proper personal protective equipment (PPE) such as eye protection and gloves while dressing a wheel.

A wheel dresser, also known as a dressing tool, is a tool or device used to dress or reshape the abrasive particles on the surface of a grinding wheel. The purpose of dressing a wheel is to restore its cutting ability and create a uniform surface on the wheel. This ensures that the wheel cuts consistently, reduces chatter and vibration and increases the wheel’s lifespan.Wheel dressers come in a variety of types and designs, each suited for specific types of grinding wheels and machines. The most common types of wheel dressers are:1- Single-point diamond dressers: These are used to create a specific shape on the wheel, and are typically used for precision grinding operations.2- Multi-point diamond roll dressers: These are used to true the wheel surface and are typically used for heavy-duty grinding operations.3- Stick or star dressers: These are made of tungsten carbide or steel and are used to true and maintain the shape of the wheel.

The frequency of dressing a grinding wheel depends on the type of wheel, the material being ground, and the grinding conditions. However, as a general rule of thumb, the wheel should be dressed at least once for every 10 grinding sessions.

The dressing ratio for a grinding wheel is the ratio of the volume of abrasive material removed from the wheel to the volume of dressing material used for the process. This ratio is an important parameter that indicates the efficiency of the dressing process.

Grinding wheels should be regularly dressed to maintain their geometry and cutting efficiency. Dressing helps to remove dull abrasive grains and expose fresh grains, which enhances the grinding performance and prolongs the wheel life.

Overlap ratio in dressing is the ratio of the width of the dressing tool to the width of the grinding wheel. This parameter affects the quality and efficiency of the dressing process. A higher overlap ratio means that more material is removed from the wheel per pass, which leads to a more aggressive dressing action but can also result in higher dressing forces and increased risk of wheel damage.

Grinding Wheel – 7 Tips for Dressing a Grinding Wheel

The grinding wheel diamond dresser is an essential tool in abrasive truing wheel and other tools we use in the diamond industry. However, these tools wear over time, which calls for the need to dress them so they can function more effectively.

Despite the apparent importance of these tools, unfortunately, only a few understand how to dress the grinding wheels. This article will provide step-by-step guides on using a grinding wheels diamond dresser. Also, we included tips for dressing diamond grinding wheels. You will find useful tips if you are a first-timer or an experienced person.

Table of Contents

• Step 1: Inspect the grinding wheel visually
• Step 2: Position the grinding wheel dresser on the wheel
• Step 3: Check for Wobble
• Step 4: Dress the wheel

• 1. Select the right dressing tool
• 2. Mount the dressing tool correctly
• 3. Step aside until the grinder reaches the maximum speed
• 4. Reduce the vibration
• 5. Use safety gears
• 6. Avoid wearing loose-fitting garments
• 7. Make coolant available

• 1. How often should I dress a grinding wheel?
• 2. Are there differences between wheel dressing and wheel truing?

What are grinding wheel dressers?

Grinding wheel dressers are tools that you can use in trimming (dressing) grinding wheel surfaces to return them to their original shapes. Grinding wheels diamond dresser works so that it exposes fresh grains for new actions.

Figure 1:A machine operator dressing a grinding wheel with dressing too

Four reasons to dress a grinding wheel

Maintaining the lifespan of tools is a critical behavior that all users of manufacturing tools must imbibe. Here are the reasons why it’s imperative to dress your grinding wheels:

• Improved efficiency: Grinding wheel and other abrasive tools accumulate particles over time. It reduces their effectiveness. Dressing a grinding wheel means it can work more efficiently as it will renew its edges, exposing new surfaces for more concise grinding.

Increased Durability: Grinding wheel will cease functioning after continuous use. However, you can extend the lifespan with proper maintenance, particularly dressing.

Better Output: The process re-balances the wheel to a more concentric shape for better output.

Value for Money: It can be expensive to replace grinding wheels. With adequate dressing, you can get the best out of your grinding wheels for an extended period.

Step-by-step guides for dressing a grinding wheel

Dressing a grinding wheel, although a simple do-it-yourself project, requires some wits. It is because it can result in an accident with any carelessness. Here are some of the step-by-step guides to dress a grinding wheel:

Step 1: Inspect the grinding wheel visually

It’s vital to ensure that the grinding wheel dresser is in good condition before you set to work. Check the wheel on the grinder to ensure that all parts are risk-free to the user. Also, see if the tool rest is in a perfect position. Since wheels wear down over time, there’s a need to slide them close to the grinding wheel.

Figure 2: New grinding wheel for electric grinder

Step 2: Position the grinding wheel dresser on the wheel

Firmly secure the grinding wheels dresser on the wheel and ensure it’s not shifting unnecessarily. Ideally, it would be best if you only left a gap of 1/16 inch between the tool rest and the grinding wheels. Anything beyond that might leave space that can drive your hand between the gap and the grinding wheel during operation. If the spacing is more than 1/16 inch, you might need to adjust the tool rest and the spark guard tool using a wrench or a spanner.

Step 3: Check for Wobble

Power on the grinder and turn it off quickly to see if it wobbles. A grinding wheel that wobbles side-to-side will require some shimming. Shimming is a way to balance the wheel and compensate for the wobbling. Alternatively, you can roll up the wheel using your hand. It will also detect any wobbling, although it might not produce a good enough result when you compare it to powering it on.

Step 4: Dress the wheel

Turn on the grinder. Place your grinding wheel diamond dresser on the tool rest, and press it against the wheel with little pressure. Move the dresser back and forth as the wheel works on it. You might need to do this for a few seconds until the wheel feels rough. Note that dressers come with replaceable parts. You can get customized new parts from NC Cutting Tools if the current one wears out.

Figure 3: Electrical grinding machine at work in the service station

Following these procedures carefully will ensure that you have a risk-free dressing a grinding wheels experience.

As a guide, here is a video on how to dress grinding wheels for improved truing:

Tips for Dressing a Diamond Grinding Wheel

Here are the seven tips for dressing a diamond grinding wheel:

Select the right dressing tool

Grinding wheels dresser comes in various types. These include dressing sticks, star or disc dressers, and diamond dressers. However, we will FOCUS on grinding wheels diamond dresser. It is due to its superior strength and versatility. Generally, diamond dressers come in two types depending on the number of diamonds they carry on their face. Type 1 has a single diamond, while the second type has multiple small diamonds on its broad surface.

Grinding wheels diamond dresser remains the hardest abrasive you can use for dressing the grinding wheels. They produce a desirable performance in comparison to other dressing tools. The good news about these tools is that you can always customize the dressing tool of your choice.

Figure 4: Single-point diamond dressing tools for grinding wheel

With NC Cutting Tool’s custom-made diamond dresser, you can choose any specification depending on your project. NC Cutting Tools will design a diamond dresser with superior performance, whether it’s a single point, multi-set cluster, or blade-specific type. It includes flawless rotation, higher frequency, and enhanced precision.

Figure 5:Diamond dressing for the high-precision grinding process

Mount the dressing tool correctly

We cannot overemphasize the importance of correctly setting up the grinder and dressing tool. Ensure that the clamp rests firmly and that the wheel can rotate freely. Also, bridge the gap between the wheel and the tool rest. As a rule of thumb, 1/16 inch is perfect for preventing the dresser or user’s hand from slipping into the tool rest and the moving wheel.

Step aside until the grinder reaches the maximum speed

Allow the grinder to speed up to the peak of its Revolution Per Minute (RPM) before you step before it. A wheel flaw can result in parts like the chip or the guard flying off. Keeping off will ensure that you are safe from any hazardous occurrences.

Reduce the vibration

Wobbling grinding wheels will wobble, which, in turn, will result in intense vibration. Also, firmly mount the dresser at the right angle of 10.15 degrees.

Use safety gears

Safety is always a priority in any workshop operation. Ensure that you wear a helmet and face shield to protect against sparks and inhaling aluminum oxide or silicon carbide dust. However, wearing a hand glove is not advisable, and the wheel can easily catch the glove during operation.

Avoid wearing loose-fitting garments

Loose-fitting dresses are a “NO” when dressing and grinding wheels. Long sleeves, jackets, and unbuttoned shirts are worn to avoid when working with grinding wheels diamond dressers. Even with a grinding wheel dresser diamond with a long handle, these dresses can get caught between the tool rest and the grinding wheels. Also, if you have long, free-flowing hair, you might want to use a hair net to tuck it in.

Make coolant available

The grinding wheel diamond dresser and the grinder give off lots of heat during use. You should keep coolant handy to reduce the temperature during overheating. If there is no coolant, allow the dresser to cool off during overheating to prevent it from early damage.

Frequently Asked Questions about Dressing a Grinding Wheel

Here are some of the questions we get often. Feel free to speak to our specialists if this article and our FAQ session don’t cover your queries.

How often should I dress a grinding wheel?

The frequency of dressing grinding wheels largely depends on how often you use them. For commercial purposes, it’s ideal for dressing your grinding wheels any time you notice the performance is unsatisfactory. Also, avoid using soft materials with your grinding wheel; they clog easily and require frequent dressing.

Are there differences between wheel dressing and wheel truing?

Although we use both terms interchangeably, there is a subtle difference between them in terms of purpose. While both operations eliminate particles from grinding wheels, dressing is more synonymous with surface finish maintenance. In contrast, truing involves putting the grinding wheels back in form from excessive wear. You will need more truing for precision grinding.

Recap and Final Thought

Now that you are familiar with the tips for dressing grinding wheels, you should have no problem getting the best result from your grinding wheels diamond dresser. And remember that NC Cutting Tools is the number one manufacturer of grinding wheels, cutting, and grinding tools. With over 20 years of experience, we are confident in supplying you with quality, uniquely customized tools at affordable prices. You can schedule a meeting with any of our specialists to get a free estimate on your projects.

Silicon Carbide Grinding Wheel Dresser

CRATEX rubber-bonded silicon carbide dressing stick for grinding wheels is ideal tool for truing, dressing and shaping different types of grinding wheels including CRATEX rubberized abrasive wheels. It is a perfect solution to keep your grinding wheel flat, sharp, clean and running smoothly!

With this easy to use, efficient and long-lasting dresser you’ll enhance your grinding wheel cutting and finishing performances. It’s simply a MUST for everyone who continuously uses a bench grinder.

Use CRATEX cleaning abrasive sticks and minimal effort and your grinding wheel will be in a top-notch form in just a few minutes. Simply choose the dressing wheel shape, grit and length and before you know it, your order will be on the way!

Recommended for CRATEX Large Grinding Wheels : Dressing Stick Size: 6” x 1/2” x 1/2”

Click the icon to jump to the desired section

CHAPTER 3

CHAPTER 4

What Is The Difference Between Dressing And Truing?

CHAPTER 1

Grinding wheels are tools used most often for grinding (abrasive cutting) operations. In our article dedicated to grinding wheels we already explained that grinding wheels are designed as self-sharpening tools, which means that the grinding process itself sharpens the wheel every time it’s used. Small abrasive cutting grains of the wheel become dull during the grinding process and break away from the bonding material, leaving the sharp grains exposed. However, this awesome self-sharpening ability is not quite enough, since the work material can cause it to load up, so it is necessary to occasionally dress or true the wheel to achieve satisfying results. If the wheels are not maintained, increased cutting forces and the created heat can cause damage to the surface finish and wheel breakage. Dressing is not so much important for rough grinding wheels, but you’ll need to always have a true, flat face on your wheel in case you’re doing some precision grinding.

Here’s where the grinding wheel dresser steps in. It is a handy tool used to remove the top layer of a grinding wheel in the purpose of:

• Truing it and making it concentric, which will minimize vibrations and improve the quality of the finishing operations. Loaded or clogged areas on the wheel will cause it to lose its roundness, and the loss of the roundness will eventually cause excessive vibrations of the bench grinder. The reason why the wheel loses its shape is because the clogged areas wear off at a different rate from the less loaded areas;
• Exposing fresh abrasive grains, which will enhance the cutting action. Dull grains of the wheels with extremely hard bond will usually remain in the wheel;
• Cleaning the pores between the abrasive grains, which get filled with workpiece fragments. This happens in case the workpiece has a softer grade than the one the wheel is designed for. In that case, the grains won’t break away in time and the workpiece parts will get stuck between them.

With dressing, the wheel will be good as new and ready for renewed grinding action!

CHAPTER 2

Grinding wheel dressers can be broadly divided in following categories:

• Dressing rolls and rotary tools – these dressers have rolls or wheels that are coated with diamonds;
• Dressing spindles. spindle-mounted tools that usually come with an integral brake and drive;
• Dressing sticks – or dressing blocks are made of bonded abrasives;
• Impregnated or grit dressing tools – these have a whole layer of diamond or superabrasive grains bonded in the matrix, much more sharp points than an ordinary multi-point tool. These are used in the same way as multi-points tools, but they are designed to provide a superior finish;
• Single-point dressing tools – these have only one diamond or superabrasive grit bonded in the tip and can be various: single point tools should be mounted at a 10°-15° angle to the wheel centerline while the contact point should be slightly below the centerline. The tools should point in the direction of wheel travel;
• Multi-point or Cluster dressing tools – unlike the single-point ones, cluster dressers have several diamonds or superabrasives across the dresser surface. They can be wide enough to reach across the entire cutting surface of the grinding wheel and most of them are used for straight-face dressing. They came into use mostly because they’re more affordable (instead of one large diamond they have several smaller ones).

Grinding wheel dressers used most often on bench grinders are as follows:

These are dressing bonded abrasives shaped as a stick or a block. You’ll usually use dressing blocks made from the same abrasive type as the grinding wheel, but you’ll choose a stronger bonding agent. Typical abrasives used in grinding wheel dressing sticks are aluminum oxide and silicon carbide. For resin and vitrified bond diamond and cBN wheels you should choose a dressing stick that is one or two grit sizes finer than the abrasive in the wheel. For metal bond diamond choose a stick the same grit size or one grit size coarser than the wheel abrasive.

These are heavy-duty dressers with long handles, a row of hardened free running either star-shaped cutters or wavy discs, and little ‘legs’ that are designed to go behind the tool rest. Star dressers provide a more ‘open’ texture, which is perfect for rough grinding, and they are more suitable for larger (e.g. 12″) grinders. They are consumable items that are going to wear down, so you’ll need to change the discs after they do.

These dressers have a short handle and you can find two types. Either those with a single diamond embedded in their face, or those with a lot of small diamonds embedded in a wide surface. Diamond is the hardest superabrasive used for truing and dressing conventional and superabrasive grinding wheels. It’s ideal for fine finishing cutting tools as it gives the grinding wheel a smoother finish. Although diamond dressers might seem pricey initially, rest assured you’ll get your money’s worth, since diamond is extremely durable and therefore a long-lasting tool.

When it comes to CNC grinders, four types of dressers can be used for dressing their wheels.

This is a wheel made of either high-speed steel or tungsten carbide, which is pressed against the grinding wheel while spinning at the same speed as the wheel. The dresser profile is the mirror image of the desired grinding wheel profile and cannot be adjusted, only replaced by a different profile.

This would be a crush roll which is coated with diamond grains. Diamond grains give them an advantage over regular crush rolls, because they wear more slowly.

These have a metal blade that has a single diamond embedded in the tip. A CNC program for dressing the wheel controls the wheel’s profile and is responsible for moving the dresser across the wheel’s surface.

These are sometimes called ‘pizza cutters’. A disc made of material (usually a diamond) is attached to the edge, and the grinding wheel’s profile is controlled by the CNC program used to wheel dressing as well.

CHAPTER 3

CRATEX silicon carbide grinding wheel dresser dresser is a perfect tool for dressing and truingdifferent kinds of grinding wheels including all rubber-bonded abrasive wheels. Thanks to its shape, fast cutting abrasive with a hardened bond, it’s an efficient, easy to handle and a long-lasting dressing stick that will help you achieve maximum performance from all your CRATEX rubberized abrasive wheels.

Selecting the appropriate dressing stick will depend on the size, type, speed, grit size and specification of the wheel, and of course, the workpiece material. A good advice would be to test several sticks to find the best possible solution for your needs.

RECOMMENDED: Check out CRATEX Mini Test Block Kit No.128B (shipping and handling included in the price)

Order Mini Block Kit No. 128B SKU: Q128B Block Kit

Dressing sticks are used for dressing and truing bench and pedestal grinder wheels. You’ll only need your hand and a dressing stick to perform the dressing which is done by moving the stick back and forth against the wheel face. In case the movement is fast, so will be the metal removal, which will cause rougher finishes on the workpiece. If the movement is slower, the grinding wheel face will be smoother, there will be less metal removal and the surface finish on the workpiece will be finer.

CRATEX dressing sticks are a perfect solution to keep your grinding wheel flat, sharp, clean and running smoothly! A MUST for everyone who continuously uses a bench grinder!

Order Square Sticks

CHAPTER 4

Both dressing and truing must be conducted in the purpose of creating satisfactory work. Both operations remove material from the grinding wheel. While dressing relates to a surface finish maintenance, truing relates to the loss of form control due to the excessive edge wear.

Although sometimes together referred to as ‘conditioning’, they mean two different operations. Conventional grinding wheels that are inexpensive can be trued and dressed at the same time and the process can be repeated periodically. However, superabrasive grinding wheels, like CBN or diamond wheels, are a serious investment and require much more attention to dressing and truing separately.

Truing is done when a new wheel is installed and before it’s used for the first time and is necessary for precision grinding. The purpose of truing is to bring every point of the grinding surface concentric with the machine spindle (to establish concentricity) and to introduce a form (shape) into a wheel. No matter how precisely manufactured, there will be a slight gap between the wheel bore and the machine spindle. Even if the gap is one thousand of a millimeter, problems like chatter marks will occur if the wheel is not trued to the center of the spindle. Conventional grinding wheels can be trued easily with a diamond cutter that is harder than the wheel, while the superabrasives cannot be cut and must be ground to size. This is done by using a sintered diamond roller or by traversing a conventional grinding wheel. Many like to use a brake-controlled truing device called BCTD which turns more slowly and provides a more precise and controllable truing. After the truing process, the wheel surface is smooth and closed, and since there are no abrasive grits exposed, the wheel can’t perform cutting.

Dressing is the process that comes after truing (especially in the case of superabrasives) and it represents grinding wheel sharpening by exposing abrasive grits above the bond. In other words, removing small chips of workpiece lodged in the wheel surface or removing dull abrasives which returns the wheel to its original dimensions and provides crystal exposure. The wheel surface after dressing is open with grits exposed.

• AIR TOOLS
• Rubberized Abrasives
• MX Abrasives
• Brightboy
• Regulating Wheels
• Spedecut

• 2023 © Cratex
• Tel: 800-800-4077
• Fax: 760-942-4513
• Email: sales@cratex.com
• Powered by IT Support San Diego | Design by San Diego SEO Expert

Diamond Wheel Dresser for Surface grinder। ड्रेसर क्या हैं डायमंड ड्रेसर से व्हील कैसे ड्रेस करे ।

Silverline Diamond Grinding Wheel Dresser

Heavy duty diamond-coated head. Dresses across the width of grinding wheels to give a flatter surface. Restores and prolongs the life of grinding wheels.

Silverline Diamond Grinding Wheel Dresser

Features:- Heavy duty diamond-coated head- Dresses across the width of grinding wheels to give a flatter surface- Restores and prolongs the life of grinding wheels- Improves balance of grinding wheel for safer working- Knurled handle provides excellent grip.

About Silverline Tools:Silverline are leading industry experts with many years history in manufacturing and supplying more than 5,000 quality hand and power tools throughout the UK and Europe. Silverline are so confident in their products that they offer a Liftetime Guarantee on all their Hand Tools, and 3 Years on Power Tools. must register your purchase online at https://www.silverlinetools.com/en-GB/Support/Guarantee within 30 days of purchase.

BANK HOLIDAY NOTICE

Please note that delivery time estimates shown at checkout may be delayed due to the bank holiday on Monday 29th May. This could delay your delivery by 1 day as our estimated time doesn’t take into account this public holiday.

Delivery Services and Prices

We offer a selection of delivery services that you can choose from. We can deliver directly to you, to your customer, or to your work site. Enjoy free or discounted shipping when placing orders over £100. Please note that delivery options at checkout vary depending on the products in your cart. See table below for further information.

DPD Saturday delivery service will only be available in the checkout from 2pm Thursday to 2pm Friday.

Public Holidays: delivery timeframes quoted exclude public holidays.

Some items are shipped directly by the manufacturer. In this case, the courier depends on manufacturer’s selection. Please see the below table for specialist direct from supplier delivery services.

Direct From Supplier Deliveries

NOTE: You will see your expected delivery timeframes during checkout.

Some large or heavy items will have restricted delivery options and may have a higher shipping cost to those listed above. We will contact you if there are any special shipping requirements.

Some delivery options have postcode restrictions, please view excluded postcodes below. We cannot offer delivery to BFPO addresses.

IMPORTANT: Please ensure you report any damages or shortages to us within 3 days of receiving your order, as these could be caused by the courier.

Which postcodes have shipping exclusions/restrictions?

Scottish Highlands: AB36-38, AB55-56, FK17-21, IV1-39, IV52-54, IV63, KW1-14, PA21-40, PH19-26, PH30-41, PH49-50

Scottish Islands: HS1-9, IV40-51, IV55-56, KA27-28, KW15-17, PA20, PA41-49, PA60-78, PH42-44, ZE1-3

Planning Ahead

Please do not schedule or start any installation work until after you have received your order and checked all goods for any defects or missing parts. This will enable you to resolve any technical questions or to order specific additional fittings if needed. We are unable to accept compensation claims towards loss of earnings for late/failed delivery of goods or missing/damaged items.

International Deliveries including the Irish Republic Channel Islands

We offer delivery services to countries all around the world, though due to the varying nature of product weights, dimensions and delivery services we invite you to contact us for a delivery quote for your specific order delivered outside the United-Kingdom.

Whether you want just one small order delivered to the other side of the world or a consignment of pallets, we can provide a delivery service fully insured and trackable to suit your needs.

Please make an enquiry for your international delivery using the below methods of contact and state what it is you would like to order (including quantity and size/colours variants) and your full delivery address including Zip/Postal code where applicable.

Please consider that if you are having the goods delivered to a country in the EU, then UK VAT rates apply. If you are having the goods delivered outside the EU, then UK VAT does not apply – this also applies if we have onward shipment proof of the goods leaving the EU.

NOTE: For deliveries outside the EU, you will have to pay your country’s import duties, taxes and any handling charges. It is your responsibility to find out what these are prior to ordering and your responsibility to declare and pay them.

We are not able to send some products abroad due to transport, import and export restrictions.

Order Tracking

You will receive a confirmation email once your item has been dispatched. We use a selection of different couriers to suit the requirements of the varying weight, dimensions and delivery locations and services required for each order, and as such it is not always possible to provide a tracking number for deliveries. In this case, you will be able to contact the courier directly, as we include their details and your consignment number in the dispatch confirmation email.

You can contact us for a delivery update if your parcel has not arrived within the timeframes stated when you placed the order.

Click Collect

Although we are working to bring a ‘Click Collect’ option to our customers, it isn’t here just yet.

We therefore cannot currently allow orders to be collected from our office or warehouses, but this option will be available in the near future.

Returns Faulty Goods

Hopefully, you won’t need to return an item, however, if you do, it is our aim to make this as simple as possible. By following the guidance below, you can help us to help you when a product is not what you expected, or is faulty. Your statutory rights are not affected by this guidance.

If you have any questions, please call our customer service team on 01179 780 174.

30-Day Money-Back Guarantee

Under our 30-Day Money-Back Guarantee you can return unwanted goods. Items should be unused, in a saleable condition, with their original packaging and with all component parts and any promotional items received. You should include your invoice and a completed returns form.

If you have any questions, please refer to our FAQ’s below.

How do I return my item?

If you purchased your item(s) from our website MAD4TOOLS.COM:

To return an item under the 30-Day Money-Back Guarantee you can (at your expense) either:

• Send it back via your local Post Office. click here for a Returns Form.
• Send it back via a Courier Collect service. Collections are on weekdays from 8.00 am to 6.00 pm, for more information call our customer service team on 01179 780 174.

Post Office return is not available for items over 1.5m in length or 4kg in weight. For these items please use the Courier Collect Service by calling or emailing our customer service team for further advice.

If you purchased your item(s) from our from our Amazon store:

• Log in to your Amazon account.
• Go to your Order History screen.
• Locate your order and select the Return option.
• Follow the Amazon guidelines.

If you purchased your item(s) from our from our eBay store:

• Log in to your eBay account.
• Go to your Purchase History screen.
• Find the item(s) you wish to return.
• Select the Returns option from the dropdown menu.
• Follow the eBay guidelines.

Which items are excluded from the 30-Day Guarantee?

Certain items are excluded from the guarantee. These include (but are not limited to) goods that are made to measure, cut, or mixed to your requirements, custom printed. Other excluded items are macerators and water pumps. For products delivered directly from our suppliers, please call our customer service team on 01179 780 174.

3 Types of Best Dressing Tools for Grinding Wheels!

What should I do if my delivery is faulty or damaged?

If you notice any damage or shortages on your goods, please inform us within 3 days of taking delivery. We would recommend refusing any delivery that looks damaged or making note of any damage to the box when signing for your delivery. If you have notified us of any Damage or Shortages with your goods within 3 days of receiving your delivery, we will either make good any non-delivery, replace, or repair any goods that are damaged or defective upon delivery, or refund to you the amount paid by you for the goods in question.

Any faulty good claims that have been reported within 3 days of taking delivery, must be returned within 30 days of taking delivery. You should include your invoice and a completed returns form. Please ensure that all petrol products are drained of fuel and oil before return. If the item has already been installed, call us on 01179 780 174 for further advice.

What do I do if my item has developed a fault after 30 days?

If you purchased the item more than 30 days ago, we aim to get the problem put right as quickly as possible. In most instances, relative to the product in questions warranty, we will either offer a repair or where this is not possible, we will replace the item with the same or an equivalent model.

If there is no warranty or repair service, or if you wish to return a faulty item:

Please remember to include your invoice, returns form and ensure that all petrol products are drained of fuel and oil before return. If the item has already been installed, call us on 01179 780 174 for further advice.

My item has developed a fault, but it’s already installed, what should I do?

If the item has already been installed, call us on 01179 780 174 for further advice.

I haven’t received my refund yet, when can I expect it?

Refunds to card and PayPal can take 3-5 working days (bank funded PayPal payments can take up to 10 working days). If you have not received your refund within the timeframe detailed, please contact us with your order and refund details.

How do I cancel my order?

A cancellation can be made up to 30 days from point of order via phone, email or mail (MAD4TOOLS.COM, Bridge House, Block 4, Cater Road, Bishopsworth, Bristol. BS13 7TW).NOTE: Certain items are excluded from this, these include (but are not limited to) goods that are made to measure, cut or mixed to your requirements, custom printed or other possible exclusions include macerators and water pumps.

Can’t find what you’re looking for? Call our customer service team on 01179 780 174.